Related
Hi.
I got into problem after flashing the Beta 7.0. I need to restore my phone using fastboot since the eRecovery that I got gave me only 3 options: download latest version and recovery, reboot, shutdown.
I have tried flashing the system.img, boot.img and recovery (both stock and TWRP). During flashing everything looked OK without any error but I still get this when booted:
"Your device has been unlocked and cant be trusted - your device is booting now..." and it got into bootloop.
darthkir said:
Hi.
I got into problem after flashing the Beta 7.0. I need to restore my phone using fastboot since the eRecovery that I got gave me only 3 options: download latest version and recovery, reboot, shutdown.
I have tried flashing the system.img, boot.img and recovery (both stock and TWRP). During flashing everything looked OK without any error but I still get this when booted:
"Your device has been unlocked and cant be trusted - your device is booting now..." and it got into bootloop.
Click to expand...
Click to collapse
try to put the update.app of B130 on dload folder on SD Card, external sd or OTG and it should be able to flash..
i had a similar issues, almost was going to go the service center when i was able to flash the firmware B130 thru the auto update from OTG (flash drive) (Hold Volume Up + Volume Down + Power).
The dload / 3 button method doesn't work any more, here is what worked for me:
I got to the state where I could only enter Fastboot mode (Press vol- and connect power cable). When I tried to start the phone / go into recovery it would only display the "Your device has been unlocked and can't be trusted" Message. My mistake was to relock the bootloader in an attempt to get the recovery to work.
I looked for hours for the answer, here is what worked for me:
follow this tutorial (the "update firmware" part)
German
English
But with real precision, every step.
If you have a european unbranded L09 you should be fine using the firmware you can find on this site:
https://thedroidguru.com/download-install-huawei-p9-b394-nougat-update-europe/
if not you gotta find the full firmware (3 files!!) yourself - good luck!
If you only want to go back to stock you should be fine afterwards.
If you want to install twrp for root/custom rom/... follow these steps after installing twrp with the tool:
Upon flashing TWRP, FIRST THING YOU MUST DO is rebooting to TWRP. If you don't do that, stock Recovery will ovewrite TWRP.
Find instructions in the TWRP threads how to enforce immediate booting to TWRP, upon you flashed it:
-Type on the PC: fastboot reboot -but don't press Enter yet.
-Press and keep pressing Vol+ and Power buttons together on the phone
-Press Enter on the PC and then immediately unplug USB cabel.
-When phone shows Booting, release Power but keep pressing Vol+. button
Hope this helps, I don't take responsability for anything, happy flashing!
Nooby Paul said:
The dload / 3 button method doesn't work any more, here is what worked for me:
I got to the state where I could only enter Fastboot mode (Press vol- and connect power cable). When I tried to start the phone / go into recovery it would only display the "Your device has been unlocked and can't be trusted" Message. My mistake was to relock the bootloader in an attempt to get the recovery to work.
I looked for hours for the answer, here is what worked for me:
follow this tutorial (the "update firmware" part)
German
English
But with real precision, every step.
If you have a european unbranded L09 you should be fine using the firmware you can find on this site:
https://thedroidguru.com/download-install-huawei-p9-b394-nougat-update-europe/
if not you gotta find the full firmware (3 files!!) yourself - good luck!
If you only want to go back to stock you should be fine afterwards.
If you want to install twrp for root/custom rom/... follow these steps after installing twrp with the tool:
Upon flashing TWRP, FIRST THING YOU MUST DO is rebooting to TWRP. If you don't do that, stock Recovery will ovewrite TWRP.
Find instructions in the TWRP threads how to enforce immediate booting to TWRP, upon you flashed it:
-Type on the PC: fastboot reboot -but don't press Enter yet.
-Press and keep pressing Vol+ and Power buttons together on the phone
-Press Enter on the PC and then immediately unplug USB cabel.
-When phone shows Booting, release Power but keep pressing Vol+. button
Hope this helps, I don't take responsability for anything, happy flashing!
Click to expand...
Click to collapse
DLOAD does not work for half a year, ie since Huawei stopped releasing FullOTA-MF-PV builds (it worked only for them)
Here, on XDA there are two proven guides for recovering Nougat (not just for EU c432 but for all custs, not only for P9 L09 but also for L19, L29) - just search for them: HWOTA7, HuRUpdater
PS: You have crossposted the same to several threads?!
I was trying to downgrade and something went wrong.
Now i'm stuck in Huawei LOGO and can't turn off phone, he keeps turning on and freeze at Huawei Logo.
He's getting really hot.
Tried a few tools to get him at adb but no luck...
Also tried update from dload sdcard but combo keys not working either...
Any ideas?
Delete
Enviado do meu iPhone usando o Tapatalk
migueli2 said:
I was trying to downgrade and something went wrong.
Now i'm stuck in Huawei LOGO and can't turn off phone, he keeps turning on and freeze at Huawei Logo.
He's getting really hot.
Tried a few tools to get him at adb but no luck...
Also tried update from dload sdcard but combo keys not working either...
Any ideas?
Click to expand...
Click to collapse
Same problem but on EVA-AL00 running AL19C636B190
Have u tried to unlock bootloader or flash boot/recovery with fastboot mode?
I have the same problem, any ideas?
I had the same issue, three only thing that worked for me was to get the phone into recovery, vol down and power and flash through DC phoenix
My P9 make "self reset" all time, until battery gets empty. I can't get into recovery
Open hisuite enter recovery area plug phone to pc you see vol down + power screen. Press vol- and power button you must go to fastboot screen. If phone recover by hisuite thats ok.
If not, you need unlocking bootloader with srk tool ( must have unlock code ) flash twrp with command fastboot flash recovery twrp.img or use srk tool to flash twrp recovery.
Enter recovery upload files to sd card, flash L09C432B322 zip than hw_eu zip. Your phone must boot with nougat. (Of course your phone dont C432, you must use your phone B322 files)
If you dont use nougat do a rollback prosedure.
master' said:
Open hisuite enter recovery area plug phone to pc you see vol down + power screen. Press vol- and power button you must go to fastboot screen. If phone recover by hisuite thats ok.
If not, you need unlocking bootloader with srk tool ( must have unlock code ) flash twrp with command fastboot flash recovery twrp.img or use srk tool to flash twrp recovery.
Enter recovery upload files to sd card, flash L09C432B322 zip than hw_eu zip. Your phone must boot with nougat. (Of course your phone dont C432, you must use your phone B322 files)
If you dont use nougat do a rollback prosedure.
Click to expand...
Click to collapse
I have same problem ,but my is Eva 19l,not support hisuite,and I can't turn on the phone check product ID can't unlock bd ...... anything can help me?
Happy baby said:
I have same problem ,but my is Eva 19l,not support hisuite,and I can't turn on the phone check product ID can't unlock bd ...... anything can help me?
Click to expand...
Click to collapse
Use dc phoneix for unlock bootloader . (I dont use so i dont know how to use)
Did anyone ever find an working solution for this, my problem is almost identical to the OP's but mine gets stuck on the bootloader unlocked warning screen, says the phone is rebooting but never does. I'm unable to turn the phone off without it instantly restarting and hanging on the bootloader warning screen, phone also gets super warm when on this screen. HELP
Hello guys!
I have bricked my P9 EVA-L09 today. i want to update it to android 7 with update from erecovery. i put files from update_data_full_hw_eu.zip and it went good but phone wont boot up and the second file "update.zip" ive extracted to dload but phone cant install it. I've tried many things to unbrick my phone but i cant do it. flashing system via fastboot is impossible cause it says that it cant be written. i have no root ant no bootloader unlocked. Please help me guys QQ
If you have C432, try this:
1. install via sdcard + 3buttons UPDATE.app from HUAWEI_P9_Rollback Package_EVA-L19_from Android 7.0_EMUI 5.0_to Android 6.0_EMUI 4.1_C900B300
2. install via sdcard + 3 buttons HUAWEI_P9_Firmware_EVA-L09_Android 6.0_EMUI 4.1.1_C432B182_Western Europe
marjaN_ said:
If you have C432, try this:
1. install via sdcard + 3buttons UPDATE.app from HUAWEI_P9_Rollback Package_EVA-L19_from Android 7.0_EMUI 5.0_to Android 6.0_EMUI 4.1_C900B300
2. install via sdcard + 3 buttons HUAWEI_P9_Firmware_EVA-L09_Android 6.0_EMUI 4.1.1_C432B182_Western Europe
Click to expand...
Click to collapse
that's the question, because i dont remember my previous working build but ill try this two packages anyway, thanks a lot for your reply
edit: now i cant even go to recovery after flashing rollback :/
edit2: i know why, you posted rollback for eva-L19 and i just copied it and flashed but phone have installed it correctly and i cant go to recovery :'(
Nobody can help me? :crying::crying::crying:
power off, then press the Power + voulume +, wipe data+cache
ziemiak said:
that's the question, because i dont remember my previous working build but ill try this two packages anyway, thanks a lot for your reply
edit: now i cant even go to recovery after flashing rollback :/
edit2: i know why, you posted rollback for eva-L19 and i just copied it and flashed but phone have installed it correctly and i cant go to recovery :'(
Click to expand...
Click to collapse
try installing 6.0 firmware for you model.
i cant go to eRecovery, i cant even shut down device - only full discharge can make it.But i can go to fastboot. Ive tried with fastboot commands but i have locked bootloader and every time my flashes are rejected by phone. The simpliest metod - HiSuite send me message: "no recovery packages are found for your phone model". It should be a way to unbrick it with fastboot but i dont know how.
Hi I was in your shoes yesterday I had to pay for the dn Phoenix to fix my phone it uses a backdoor to install firmware from fastboot
You could try and look for the backdoor commands I found this , I would post a link but can't yet
fastboot oem backdoor info
FB LockState: LOCKED
USER LockState: LOCKED
fastboot oem backdoor get
FBLOCK**obfuscated**
fastboot oem backdoor end
remote: fastboot stat not match
fastboot oem get-bootinfo
locked
fastboot oem check-rootinfo
old_stat: SAFE
now_stat: SAFE
change_time: 0000000000
fastboot oem check-image
secure image verify success
fastboot oem relock
remote: stat not match
fastboot oem backdoor set
remote: data parse fail
fastboot oem frp-erase
Haven't tried, but should remove the Factory Reset Protection (FRP)
fastboot oem emmc_diag
cid info:
mid 17,oid 256,pnm 064G70,prv 0.0,psn 0x18b66278,
csd dump:
D02700320F5903FFFFFFFFEF864000AB00
ext_csd dump:
...
FMW FAIL! WRITE PROTECT!
fastboot oem emmc-dump
unknown status code
fastboot oem get_key_version
huawei_key_v1
fastboot oem battery_present_check
3984mv
fastboot oem get_hwnff_ver
Ver2.3
fastboot oem get-psid
SN:**YourIMEI**
fastboot oem get-build-number
V100R001C00B000
fastboot oem get-product-model
HUAWEI M2-A01W
I will try to send my Huawei to warranty service and if they wont repair my phone ill pay for DC Phoenix too
I had the same problem!
Hi there.
Was in the same situation as you not so long ago.
Get a micro SD card, plug into PC, create a dload folder then download the rollback file from the Huawei website.
I'm a new user so can't post URL. Just Google "Huawei P9 rollback" should be the 2nd option (consumer.huawei link)
Put in the dload folder and put into your P9.
Press and hold power, vol up and down together till the Huawei logo appears and let go when you feel the vibrate.
This should force update and restart. (does not rollback to email 4.1, only unlocks the rollback from emui 5)
Next you need to download your previous firmware, in my case I'm in the UK with unlocked P9, so I downloaded EVA-L09C432B166.
Same again, put micro SD into PC, delete the rollback file and put your firmware in its place.
Put back in the P9 and repeat the above force update.
This will put you back to working stable stock.
For further reassurance, download a build previous to B166 so when it's up and running you can search for an OTA update to make sure all is in order.
Hope this helps.
Did you meant that the rollback flashes without going to eRecovery? I said some posts earlier that i cannot enter eRecovery so i cant dload anything. Im stuck on Huawei logo all the time do you think than i can flash something via dload without going to eRecovery?
erecovery is different.
I'm saying to do a force update, but in order to do so you need a microSD card.
Erecovery involves holding power up while connecting to PC in order to use HiSuite etc to recover.
Force updater tells the phone to search for dload folder on SD card or phone and install the update before trying to boot up OS.
So, if you connect microSD to your PC via a card reader etc and not via your phone, you can create a dload folder, download the rollback file from Huawei (above) the file is only around 80mb or so, plug the SD card back into your phone while powered off, hold down Power + vol up + vol down. The Huawei logo will appear, when it disappears let go of all the buttons. This should bring up the Update screen.
At this point the phone will install the rollback file. and this will bypass the rollback prevention in emui 5 and therefore allow you to install a previous emui build (4.1)
Again though your phone will still not boot at this point as there is no OS working or installed.
So you need to download the corresponding firmware for your phone/country/operator. Once downloaded, remove the memory card from the phone, connect to PC via card reader, delete the rollback file you placed in the dload folder and replace it with the downloaded OS and repeat the process used to install the rollback.
From there you should be back to stock marshmallow.
I should point out the files you download may be in zip folders. You need to extract the "update" file and that's what you place in the dload folder.
Hope this all makes sense, if not I can make a YouTube video and post it.
Good luck.
Now i know what did you mean, but sadly i cant update it too. I tried with my friend's P9 and when i hold these 3 buttons then shows special update screen and in my P9 it doesnt probably because of my bad flash rollback for P9 EVA-L19 and i have EVA-L09 model
http://www.android-hilfe.de/thema/downgrade-von-b360-zurueck-auf-b182.813366/
You must first make a step.
Only http://download-c.huawei.com/download/downloadCenter?downloadId=92743&version=363740&siteCode=de
Then
http://download-c.huawei.com/download/downloadCenter?downloadId=91783&version=358257&siteCode=de
're After You on MM and then can do what you want.
In the first link is a guide.
I did the same thing is what you doing today I've tried this and it fixed my phone
ziemiak said:
Now i know what did you mean, but sadly i cant update it too. I tried with my friend's P9 and when i hold these 3 buttons then shows special update screen and in my P9 it doesnt probably because of my bad flash rollback for P9 EVA-L19 and i have EVA-L09 model
Click to expand...
Click to collapse
The rollback package for L09 model is here: http://download-c.huawei.com/download/downloadCenter?downloadId=91892&version=363759&siteCode=es
Inform the results please.
I made a video to better understand. This wideo is showing that phone isn't searching any dload folder. https://youtu.be/oD9AI_6SqLs
edit: i have tried your advices to put rollback and try to dload it and then same with firmware but there is no reaction i didnt see there any circle with progress of flashing (like it was before i flashed rollback for L19)
Mine is now doing the exact same thing - I too tried the dload method to update from C432B182 to C432B361 and it's screwed my device up too.
Until I tried to use the 'rollback' package, it would at least allow me to power off, so I could get back into the Update screen - after doing that, and trying the B182 again, it's got into this position where I can do literally nothing with it. No combination of buttons, no matter how long I try to hold them, seems to do anything.
An update...
After letting my battery drain completely, I have been able to get into Fastboot mode, by pressing and holding the Volume Down button whilst connecting a USB cable to my PC.
From here, I have been able to run DC-Phoenix, and have been able to write some .APP files to it - which has at the very least got it booting into eRecovery, rather than the boot loop it had before, but is still not fully booting.
It looks like I might need the full, original firmware, in order to proceed?
And I've got about 68 hours left to flash using DC-Phoenix, or I'll have to spend another €15!
Yes you download the original firmware unzip it and put it in the "dload" folder of SD card then do a force update. Hold all the buttons vol + vol - and power
hi everyone...Please help!
I would like to update to( L19C636B361 EMUI 5.0). But I am stuck at a bootloop as I flashed in the wrong order. I first flashed the update.app (HUAWEI P9 Rollback Package-EVA-L19, from EMUI5.0+Android7.0 rollback to EMUI4.1+Android 6.0, C900B300) instead of updating to update.app(L19C636B361) [ wrong SD card inserted].
Then the phone rebooted and I got into the bootloop at Huawei logo. It cannot be turned off. It can only go into fastboot mode. Bootloader is locked and I cannot unlock it (though I havent unlock code). I tried adb/fastboot
There is always an error:
"FAILED: Remote: Command not allowed"
Now I tried to extract (L19c636b190) system.img , recover.img, boot img, flash it via adb/fastboot, but all failed. When I try to get into fastboot it says locked for both lines, and HiSuite tells me it has no software version for this phone version to repair the phone.
Could anyone help me solve the above situation?
Big [email protected]@
Anyone can help....please.
Coz i bring it to the service center, they charge me a unresonable price.
Try with the Marshmallow version and three buttons
Hey buddy. I had the same situation. Here is what I did: First format your sd card. After then download the right firmware where you can find at the huawei support official web page. After than try dload method. First time it will fail but your phone will open. Do a factory reset. Open your phone and flash firmware with dload method again. This time it will be successful and your phone will be stock. Just try. Sometimes methods fail bcoz of wrong files or sd card mistakes.
hiphoplife77 said:
Hey buddy. I had the same situation. Here is what I did: First format your sd card. After then download the right firmware where you can find at the huawei support official web page. After than try dload method. First time it will fail but your phone will open. Do a factory reset. Open your phone and flash firmware with dload method again. This time it will be successful and your phone will be stock. Just try. Sometimes methods fail bcoz of wrong files or sd card mistakes.
Click to expand...
Click to collapse
hi buddy, thanks for your reply
I follow your instrustions, i download the firmware on huawei web site {huawei_Asia_L19c636b190_16_01_2017(3,246,250kb)} with SD card format (fat32) or (exFat). Itried to dload method, I hold volume+- and power key and plug in to computer(windows 10). The phone will vibrate after 5 seconds. But it stuck into huawei logo,it cannot move forward to EMUI update. Besides, the notification light is red and flashing. Reboot and reboot again.
On the other hand, i tried the fastboot mode. I confirmed my device driver works with window, but i don't have any unlock code in order to flash any 3rd party rom. In my P9 , It showed "phone lock" & FRP Lock".
How did you work with dload method? Please kindly share with me ...thank for your reply again.
I had same issue with L19C432B378 92mb rollback file, first time bootloop. Try 5-6 times with 3 button restart and finally enter dload mode.
Second time 92mb flashing and my phone boot L19C900B300.
If there is red led notification, you are out of battery. Charge it about 15 minute first. So card format must be fat32 and fully formatted, not quick format. After than dload method. One more thing; dont plug your phone when trying dload method. Just hold 3 button about 10 seconds. Just try again. If you have right firmware, you will be successful.
hiphoplife77 said:
If there is red led notification, you are out of battery. Charge it about 15 minute first. So card format must be fat32 and fully formatted, not quick format. After than dload method. One more thing; dont plug your phone when trying dload method. Just hold 3 button about 10 seconds. Just try again. If you have right firmware, you will be successful.
Click to expand...
Click to collapse
Hi,
I have the same problem. After trying update in dload mode stuck in bootloop mode. I tried several times to reenter dload mode, but unsuccessful. Now I am out of battery and didn't want to charge in any mode.
Keep restarting every time I put it to charge. Any idea how to charge the battery?
Thanks
Did you got any solution?? Im having the same problem right now
Here’s what you need to fix your P10/P10+ brick.
This method was tested on a bricked P10 (didn’t test on the P10+)
Bootloader already unlocked + Code (no need of twrp)
SD Card
Custom recovery (fix the entire update process)
Stock rom UPDATE.APP from update.zip and update_full_xxx-xxx_hw_xx.zip
for your P10 + P10+ (choose the one you want to install, no need to be the one that come from with your P10, it could be the most recent one but linked to your exact model)
Be patient
Extract the stock rom update.zip and update_full_xxx-xxx_hw_xx.zip, both have an UPDATE.APP,
we are going to flash the one from the update.zip first and repeat the same process for the update_full_xxx-xxx_hw_xx.zip one.
(1)Get ready your SD card
Insert your SD card on the PC, create a folder at the root and name this one dload, move the update.APP from the update.zip
to the dload folder.
(2)Boot your phone in fastboot (Hold Vol- + Power) USB cable need to be plug
Launch terminal on OSX or Windows with adb/fastboot
Write the command fastboot flash recovery customrecovery.img
(3) Before rebooting your phone, insert your sd card that contain dload folder (update.app stock rom from update.zip) inside your P10/P10+
Turn off your P10/P10+
(4) Unplug the USB cable and hold vol+/vol- 5 to 10 sec or (until you see the message this device can not be trusted)
(5)Now the custom recovery updater should trigger and your P10/P10+ is updating, wait until 100% (it restart by itself).
(6)Your P10/P10+ should now boot without problem (bootloader locked)
(7) Is not finish yet, you are going to face NRD90M Test-keys that is normal, you simply need to
flash your cust.
(8) For that, we repeat the same process than before but instead of using the update.app from update.zip, you use the one from update_full_xxx-xxx_hw_xx.zip and replace the one you have on your sd card (dload folder)
(9)reboot your P10/P10+ in fastboot (with of course USB cable plug and hold vol- + power)
There you simply write the command, fastboot oem unlock yourcode. Your phone is going to reset to unlock back your bootloader and you need to go back to fastboot
(10) after that, you reflash again the recovery with customrecovery.img using the command fastboot flash recovery customrecovery.img
and you reboot again in the custom recovery mode (same than before) there the P10/P10+ is updating again, take a few secs
(11) the P10/P10+ will restart and boot in the UI, congrats.:good::good:
P.S : This process was not possible without proper change in recovery and manipulation, hopefully it help you
to recover your brick.
neverd said:
Here’s what you need to fix your P10/P10+ brick.
This method was tested on a bricked P10 (didn’t test on the P10+)
Bootloader already unlocked + Code (no need of twrp)
SD Card
Custom recovery (fix the entire update process)
Stock rom UPDATE.APP from update.zip and update_full_xxx-xxx_hw_xx.zip
for your P10 + P10+ (choose the one you want to install, no need to be the one that come from with your P10, it could be the most recent one but linked to your exact model)
Be patient
Extract the stock rom update.zip and update_full_xxx-xxx_hw_xx.zip, both have an UPDATE.APP,
we are going to flash the one from the update.zip first and repeat the same process for the update_full_xxx-xxx_hw_xx.zip one.
(1)Get ready your SD card
Insert your SD card on the PC, create a folder at the root and name this one dload, move the update.APP from the update.zip
to the dload folder.
(2)Boot your phone in fastboot (Hold Vol- + Power) USB cable need to be plug
Launch terminal on OSX or Windows with adb/fastboot
Write the command fastboot flash recovery customrecovery.img
(3) Before rebooting your phone, insert your sd card that contain dload folder (update.app stock rom from update.zip) inside your P10/P10+
Turn off your P10/P10+
(4) Unplug the USB cable and hold vol+/vol- 5 to 10 sec or (until you see the message this device can not be trusted)
(5)Now the custom recovery updater should trigger and your P10/P10+ is updating, wait until 100% (it restart by itself).
(6)Your P10/P10+ should now boot without problem (bootloader locked)
(7) Is not finish yet, you are going to face NRD90M Test-keys that is normal, you simply need to
flash your cust.
(8) For that, we repeat the same process than before but instead of using the update.app from update.zip, you use the one from update_full_xxx-xxx_hw_xx.zip and replace the one you have on your sd card (dload folder)
(9)reboot your P10/P10+ in fastboot (with of course USB cable plug and hold vol- + power)
There you simply write the command, fastboot oem unlock yourcode. Your phone is going to reset to unlock back your bootloader and you need to go back to fastboot
(10) after that, you reflash again the recovery with customrecovery.img using the command fastboot flash recovery customrecovery.img
and you reboot again in the custom recovery mode (same than before) there the P10/P10+ is updating again, take a few secs
(11) the P10/P10+ will restart and boot in the UI, congrats.:good::good:
P.S : This process was not possible without proper change in recovery and manipulation, hopefully it help you
to recover your brick.
Click to expand...
Click to collapse
Thanks, will try this tomorrow!
This sound interesting if this method is working both P10 and P10+. It mean that we can rebrand all of L09 models to L29 easily. Am i right? No more FunkyHuawei.
Sent from my iPad using Tapatalk
I have a problem, my P10 boots and lets me configure like it's the first time, but doesn't go anywhere from there, just keeps asking the same stuff... Pls help :/
neverd said:
Here’s what you need to fix your P10/P10+ brick.
This method was tested on a bricked P10 (didn’t test on the P10+)
P.S : This process was not possible without proper change in recovery and manipulation, hopefully it help you
to recover your brick.
Click to expand...
Click to collapse
Perfectly. Quite another matter. :good:
CrazyKat8091 said:
This sound interesting if this method is working both P10 and P10+. It mean that we can rebrand all of L09 models to L29 easily. Am i right? No more FunkyHuawei.
Sent from my iPad using Tapatalk
Click to expand...
Click to collapse
Not sure about the rebranding, for that you need to mod your oem info and product/vendor id.
There is no need of FunkyHuawei, I actually don't support those kind of forcing.
SkexxGo said:
I have a problem, my P10 boots and lets me configure like it's the first time, but doesn't go anywhere from there, just keeps asking the same stuff... Pls help :/
Click to expand...
Click to collapse
Question about the bootloader relock
the command to relock is fastboot oem relock yourcode.
Now about your issue, did you try a wipe cache/wipe factory/reset, go into the stock recovery and do a wipe cache/wipe factory reset.
neverd said:
Here’s what you need to fix your P10/P10+ brick.
This method was tested on a bricked P10 (didn’t test on the P10+)
Bootloader already unlocked + Code (no need of twrp)
SD Card
Custom recovery (fix the entire update process)
Stock rom UPDATE.APP from update.zip and update_full_xxx-xxx_hw_xx.zip
for your P10 + P10+ (choose the one you want to install, no need to be the one that come from with your P10, it could be the most recent one but linked to your exact model)
Be patient
Extract the stock rom update.zip and update_full_xxx-xxx_hw_xx.zip, both have an UPDATE.APP,
we are going to flash the one from the update.zip first and repeat the same process for the update_full_xxx-xxx_hw_xx.zip one.
(1)Get ready your SD card
Insert your SD card on the PC, create a folder at the root and name this one dload, move the update.APP from the update.zip
to the dload folder.
(2)Boot your phone in fastboot (Hold Vol- + Power) USB cable need to be plug
Launch terminal on OSX or Windows with adb/fastboot
Write the command fastboot flash recovery customrecovery.img
(3) Before rebooting your phone, insert your sd card that contain dload folder (update.app stock rom from update.zip) inside your P10/P10+
Turn off your P10/P10+
(4) Unplug the USB cable and hold vol+/vol- 5 to 10 sec or (until you see the message this device can not be trusted)
(5)Now the custom recovery updater should trigger and your P10/P10+ is updating, wait until 100% (it restart by itself).
(6)Your P10/P10+ should now boot without problem (bootloader locked)
(7) Is not finish yet, you are going to face NRD90M Test-keys that is normal, you simply need to
flash your cust.
(8) For that, we repeat the same process than before but instead of using the update.app from update.zip, you use the one from update_full_xxx-xxx_hw_xx.zip and replace the one you have on your sd card (dload folder)
(9)reboot your P10/P10+ in fastboot (with of course USB cable plug and hold vol- + power)
There you simply write the command, fastboot oem unlock yourcode. Your phone is going to reset to unlock back your bootloader and you need to go back to fastboot
(10) after that, you reflash again the recovery with customrecovery.img using the command fastboot flash recovery customrecovery.img
and you reboot again in the custom recovery mode (same than before) there the P10/P10+ is updating again, take a few secs
(11) the P10/P10+ will restart and boot in the UI, congrats.:good::good:
P.S : This process was not possible without proper change in recovery and manipulation, hopefully it help you
to recover your brick.
Click to expand...
Click to collapse
Hi neverd, I'm gonna give this method a try. Could you tell me where I can find the appropriate files for my P10 VTR-L29C636B120?
Much thanks.
JustXDAing said:
Hi neverd, I'm gonna give this method a try. Could you tell me where I can find the appropriate files for my P10 VTR-L29C636B120?
Much thanks.
Click to expand...
Click to collapse
Carefully, they use the same name (update.zip) but one is the full ota, the other one the ota mf (cust, etc. the one that you need to flash the second time)
Update.zip VTR-L29C636B120
Update cust/hw xxx
neverd said:
Question about the bootloader relock
the command to relock is fastboot oem relock yourcode.
Now about your issue, did you try a wipe cache/wipe factory/reset, go into the stock recovery and do a wipe cache/wipe factory reset.
Click to expand...
Click to collapse
Thanks about the relock command. I'll try it when I recover my phone.
I tried that, but it's like I don't have the full system installed, I tried a "full" ROM on the first flash, but I don't think it was actually a full rom, it was too small, I wanted to try another one, but the file being over 4gb I can't even copy it to a fat32 sd card... If I find another version that is a little smaller, maybe I could try, but now I only have erecovery, can't access anything else, hope it's enough.
neverd said:
Carefully, they use the same name (update.zip) but one is the full ota, the other one the ota mf (cust, etc. the one that you need to flash the second time)
Update.zip VTR-L29C636B120
Update cust/hw xxx
Click to expand...
Click to collapse
Thanks for the files!
I'm having a problem at step 4, it says software install failed right after 5%.
Just to confirm what I did. Press all 3 buttons (vol up, vol down, power) on until screen shows message.
Guys check this thread https://forum.xda-developers.com/mate-9/how-to/guide-mate-9-flash-update-package-t3593108 it will flash the complete FULL Firmware and you also got your bootloader closed again
JustXDAing said:
Thanks for the files!
I'm having a problem at step 4, it says software install failed right after 5%.
Just to confirm what I did. Press all 3 buttons (vol up, vol down, power) on until screen shows message.
View attachment 4136448
Click to expand...
Click to collapse
I'm having the same problem, can someone send me the files to the VTR-L09 C432? Or maybe the VTR-L29 if my phone supports it, I'd like the dual sim feature.
Just to make sure I'm using the right firmware.
If I find a solution I'll share it here as well btw.
crucky said:
Guys check this thread https://forum.xda-developers.com/mate-9/how-to/guide-mate-9-flash-update-package-t3593108 it will flash the complete FULL Firmware and you also got your bootloader closed again
Click to expand...
Click to collapse
Does it work for P10 Plus (VKY) ? I only see VTR oeminfo/recoveries files in the zip.
Edit : I went ahead and renamed everything in the VTR folder to VKY (except for eominfo files, since I just want to update), and it worked ! Updated from VKY-L29C432B123 to B130
Hi all,
I have the same issue software install failed right after 5%. Did anyone get past this?
What other files other than update in dload folder need to be present?
Thanks
---------- Post added at 05:09 PM ---------- Previous post was at 04:33 PM ----------
SkexxGo said:
I'm having the same problem, can someone send me the files to the VTR-L09 C432? Or maybe the VTR-L29 if my phone supports it, I'd like the dual sim feature.
Just to make sure I'm using the right firmware.
If I find a solution I'll share it here as well btw.
Click to expand...
Click to collapse
Have a look for files :
http://hwmt.ru/hwmtsite/firmware-database/?firmware_model=VTR&firmware_page=0
I think it is the FULL OTA required.
I still cannot get mine to go past 5% stage.
Atf130 said:
Hi all,
I have the same issue software install failed right after 5%. Did anyone get past this?
What other files other than update in dload folder need to be present?
Thanks
---------- Post added at 05:09 PM ---------- Previous post was at 04:33 PM ----------
Have a look for files :
http://hwmt.ru/hwmtsite/firmware-database/?firmware_model=VTR&firmware_page=0
I think it is the FULL OTA required.
I still cannot get mine to go past 5% stage.
Click to expand...
Click to collapse
I've did it with mine, take a look to this post https://forum.xda-developers.com/ma...te-package-t3593108/post72148764#post72148764
CrazyKat8091 said:
This sound interesting if this method is working both P10 and P10+. It mean that we can rebrand all of L09 models to L29 easily. Am i right? No more FunkyHuawei.
Click to expand...
Click to collapse
Really interested in this one too. Do you have any additional information please? As I just have plan to pull the trigger on funkyhuawei method during the next weekend... But of course I would rather use this manual method if possible.
Guys, did you flash the custom recovery before trying to update.
You really need to flash the stock recovery with the custom recovery, this fix the 5% update fail.
You can also flash recovery2 with.
neverd said:
Guys, did you flash the custom recovery before trying to update.
You really need to flash the stock recovery with the custom recovery, this fix the 5% update fail.
You can also flash recovery2 with.
Click to expand...
Click to collapse
Write that you need to extract customrecovery.img from customrecovery.zip. That would be understandable.
Hi,
does this work - i bricked my Huawei P10 with VTR-L29C432B113 firmware like this
Installed TWRP and i flashed magisk.zip -> that worked for a while
But on next phone reboot it says there is no space on the storage 0%
Now i cant do anything - phone is not usable..
Exept booting twrp and fastboot&rescue mode wich shows
PHONE unlocked
FRP Lock
When i try to
fastboot flash boot boot.img it says that stupid message command not allowed..
I tried to put in a SD Card with the folder dload and an update.app on it in and tried to flash it via VOL+ and VOL- but that fails
Does the provided method work or what can i do?
Thanks! chrizz