hi folks,
I have tried configuring a PAN network using the private subnet 192.1658.50.0/24, giving explicit addresses to my PC (192.168.50.1) and my BA (192.168.50.2).
I set up the BA's address in System->Connections->Network Cards-> Bluetooth PAN driver
i tell my Windows PC to connect to the PAN, the BT tray icon goes green (means active connection on WIDCOMM stack), but I can't ping the device. It disconnects shortly thereafter.
Any ideas?
Same here with BlueSoleil PAN :/
And have u tried windows to configure ip automatic? I still think it must work without any user-additional-interaction
Install helmi's broadcom bluetooth stack into your device, and remove any bluetooth software from your pc so it will use microsoft generic driver, then setup pan connection from your BA and connect your pc to it
anyone experiencing slowness / lockup on their HTC when plugged into the USB port?
Windows loades the HTC USB Driver and my handheld becomes unresponsive and is unable to establish an activesync.
when i unplug the USB the phone becomes responsive again
when i use my bluetooth connection - i have no such problem.
when it doesnt work/sync - here is the activesync debug:
Pinging Desktop gateway 192.168.1.1 started
Ping echoed successfully
The IP address of device is unknown
Unable to establish a connection between the PC and the device. Get up-to-date solutions to common connection problems. Please click the following link:
http://go.microsoft.com/fwlink/?LinkId=65257
The device appears to be disconnected. Please connect your device to the PC
ActiveSync is performing a sync, please wait......
Searching ActiveSync log file
Log start found
No errors found in ActiveSync log file
Exiting
when it does work/sync this is the activesync debug:
Pinging Desktop gateway 192.168.1.1 started
Ping echoed successfully
Pinging Device 127.0.0.1 started
Ping echoed successfully
Attempting to connect to device
Device operating system version 5.2.1620
ActiveSync is performing a sync, please wait......
Searching ActiveSync log file
No errors found in ActiveSync log file
Exiting
Has anyone else had problems getting their N6 to consistently connect to Bluetooth devices properly? My N6 always says pairing or connecting to the device and then says it failed to connect, I have to do this several times before it will connect successfully. It's super inconsistent. Is there an easy fix?
Hi, i searched the whole forum and no luck =(
After oreo update, the sixaxis app stopped working.
Usually worked at method 2, but now it says "wrong number of ports were opened"
I tried somehow to connect the sixaxis with directly system Bluetooth, but It requires a pin.
I tried otg cable and none of those steps worked.
I'm so sad, any help please =))
fbrauns said:
Hi, i searched the whole forum and no luck =(
After oreo update, the sixaxis app stopped working.
Usually worked at method 2, but now it says "wrong number of ports were opened"
I tried somehow to connect the sixaxis with directly system Bluetooth, but It requires a pin.
I tried otg cable and none of those steps worked.
I'm so sad, any help please =))
Click to expand...
Click to collapse
I have the same issue. I believe its to do with Oreo update. Try emailing the dev, I have emailed them but no reply so far
This problem will be forever
It seems that the developer is dizzy and almost crazy. Because it won't be able to overcome this. Or because he has given up and resigned his life in the real world
Sixaxis works for me in almost every oreo custom ROM, not sure what you have experienced but mine works, I tried all oreo ROMs to get the best of PUGB smooth non-overheating like a lava and used sixaxis in every single one of them.
I just change my connection method to 2 and nothing else. *at first I changed my dualshock bluetooth address using the OTG* and then didn't need to do it all over again.
aboodyaiman said:
Sixaxis works for me in almost every oreo custom ROM, not sure what you have experienced but mine works, I tried all oreo ROMs to get the best of PUGB smooth non-overheating like a lava and used sixaxis in every single one of them.
I just change my connection method to 2 and nothing else. *at first I changed my dualshock bluetooth address using the OTG* and then didn't need to do it all over again.
Click to expand...
Click to collapse
So are you using Bluetooth or is it working with OTG?
---------- Post added at 06:45 PM ---------- Previous post was at 05:49 PM ----------
aboodyaiman said:
Sixaxis works for me in almost every oreo custom ROM, not sure what you have experienced but mine works, I tried all oreo ROMs to get the best of PUGB smooth non-overheating like a lava and used sixaxis in every single one of them.
I just change my connection method to 2 and nothing else. *at first I changed my dualshock bluetooth address using the OTG* and then didn't need to do it all over again.
Click to expand...
Click to collapse
Tried method 2 and it didn't work for me. I'm on stock OOS
Quick Start:
- Pair controllers via USB using supplied utility
- Use 'start' and 'stop' to toggle driver
- Press power button on controllers to activate
- Change input method to 'Sixaxis Controller'
- Check 'help' menu for detailed instructions
Getting bluetooth address...
Attempting connection method 2...
Driver Starting...
Wrong number of ports were opened
Error: Failed to configure bluetooth
Getting bluetooth address...
Attempting connection method 1...
Driver Starting...
Error: Failed to configure bluetooth
Getting bluetooth address...
Attempting connection method 2...
Driver Starting...
Wrong number of ports were opened
Error: Failed to configure bluetooth
Getting bluetooth address...
Attempting connection method 3...
Driver Starting...
Could not find stack manager interface in library
Error: Failed to configure bluetooth
Getting bluetooth address...
Attempting connection method 4...
Driver Starting...
Could not load bluetooth library
Error: Failed to configure bluetooth
Getting bluetooth address...
Attempting connection method 5...
Driver Starting...
Could not load HCI library
Error: Failed to configure bluetooth
Getting bluetooth address...
Attempting connection method 6...
Driver Starting...
Could not set HCI raw mode
Error: Failed to configure bluetooth
Getting bluetooth address...
Attempting connection method 7...
Driver Starting...
Could not set HCI raw mode
Error: Failed to configure bluetooth
Attempting to close server...
Restoring previous bluetooth state...
Disconnected
ceanth said:
So are you using Bluetooth or is it working with OTG?
---------- Post added at 06:45 PM ---------- Previous post was at 05:49 PM ----------
Tried method 2 and it didn't work for me. I'm on stock OOS
Quick Start:
- Pair controllers via USB using supplied utility
- Use 'start' and 'stop' to toggle driver
- Press power button on controllers to activate
- Change input method to 'Sixaxis Controller'
- Check 'help' menu for detailed instructions
Getting bluetooth address...
Attempting connection method 2...
Driver Starting...
Wrong number of ports were opened
Error: Failed to configure bluetooth
Getting bluetooth address...
Attempting connection method 1...
Driver Starting...
Error: Failed to configure bluetooth
Getting bluetooth address...
Attempting connection method 2...
Driver Starting...
Wrong number of ports were opened
Error: Failed to configure bluetooth
Getting bluetooth address...
Attempting connection method 3...
Driver Starting...
Could not find stack manager interface in library
Error: Failed to configure bluetooth
Getting bluetooth address...
Attempting connection method 4...
Driver Starting...
Could not load bluetooth library
Error: Failed to configure bluetooth
Getting bluetooth address...
Attempting connection method 5...
Driver Starting...
Could not load HCI library
Error: Failed to configure bluetooth
Getting bluetooth address...
Attempting connection method 6...
Driver Starting...
Could not set HCI raw mode
Error: Failed to configure bluetooth
Getting bluetooth address...
Attempting connection method 7...
Driver Starting...
Could not set HCI raw mode
Error: Failed to configure bluetooth
Attempting to close server...
Restoring previous bluetooth state...
Disconnected
Click to expand...
Click to collapse
I didn't try it on OOS actually, and input method was left untouched.
Sixaxis works with bluetooth I only used OTG in pairing at first, maybe your app is somehow corrupted?
Btw sixaxis still works on Pie too.
Still not working for me
anyone found any solution for it?
Hulk555 said:
anyone found any solution for it?
Click to expand...
Click to collapse
Nope, only solution I could find was to buy a Nintendo switch. On the plus side my phone battery now lasts for days as I don't play any games on it
aboodyaiman said:
I didn't try it on OOS actually, and input method was left untouched.
Sixaxis works with bluetooth I only used OTG in pairing at first, maybe your app is somehow corrupted?
Btw sixaxis still works on Pie too.
Click to expand...
Click to collapse
Are you sure about that: is sixaxis working on Pie?
Hi all!
I am kind of new to XDA so please bear with me. I have an issue with Sixaxis Controller application where It does not connect via bluetooth. I have taken all the steps and checked them 15 times now. I have pasted the exact error here.
If someone could please explain why this is happening and if it is possible to fix, I would DEEPLY appreciate this. Furthermore I had noticed that the SELinux was enforced and many reddit posts mentioned changing it to permissive so I had to install TGP Kernel, but even that had no effect!
Thanks again!
Error:
Getting bluetooth address...
Attempting connection method 1...
Driver Starting...
Error: Failed to configure bluetooth
Getting bluetooth address...
Attempting connection method 2...
Driver Starting...
Could not load bluetooth library
Error: Failed to configure bluetooth
Getting bluetooth address...
Attempting connection method 3...
Driver Starting...
Could not load bluetooth library
Error: Failed to configure bluetooth
Getting bluetooth address...
Attempting connection method 4...
Driver Starting...
Could not load bluetooth library
Error: Failed to configure bluetooth
Getting bluetooth address...
Attempting connection method 5...
Driver Starting...
Could not load HCI library
Error: Failed to configure bluetooth
Attempting to close server...
Restoring previous bluetooth state...
Disconnected
Getting bluetooth address...
Attempting connection method 2...
Driver Starting...
Could not load bluetooth library
Error: Failed to configure bluetooth
Getting bluetooth address...
Attempting connection method 1...
Driver Starting...
Error: Failed to configure bluetooth
Getting bluetooth address...
Attempting connection method 2...
Driver Starting...
Could not load bluetooth library
Error: Failed to configure bluetooth
Getting bluetooth address...
Attempting connection method 3...
Driver Starting...
Could not load bluetooth library
Error: Failed to configure bluetooth
Getting bluetooth address...
Attempting connection method 4...
Driver Starting...
Could not load bluetooth library
Error: Failed to configure bluetooth
Getting bluetooth address...
Attempting connection method 5...
Driver Starting...
Could not load HCI library
Error: Failed to configure bluetooth
Getting bluetooth address...
Attempting connection method 6...
Attempting to close server...
Restoring previous bluetooth state...
Driver Starting...
Disconnected
Can't connect to pipe for device
If I had to guess, the driver hasn't been updated to be compatible with later versions of android. Are you referring to the Sixaxis app by Dancing Pixel Studios?
Ah. Yes. It is the sixaxis app by dancingpixel!