Hello, i have question. Soon i will replace my damaged screen to another, and question is should i change thermal paste or better not ?
if yes which one will be ok for this.
thanks.
Hi I repaired mine 2 months ago and used Artic Silver MX-4. Use the same amount as before.
EDIT: I first cleaned the old paste with isopropyl alcohol.
Related
My touch screen stopped working on my phone, but the screen is still visible. I'm assuming it's the digitizer. I was wondering if anybody has done or tried replacing only the digitizer. Does this work, is it better just to replace both? Any suggestions? Thanks.
Save yourself the headache
Just replace the complete screen unit (lcd + digitizer).
The digitizer is held on the screen with some super strong adhesive that is nearly impossible to get off cleanly. Also, there are three (4?) thin ribbon tabs that have to be soldered to the board on the rear of the lcd. Unless you are really confident with a soldering iron, it is extremely hard to do.
I replaced my screen unit in about a half hour. Make sure you go to the wiki and find one of the excellent disassembly guides before you start.
Thanks
Thanks, that's exactly the information i needed to know. I found the fon logix video. Is it only a t6 tool i need, or do i also need a t5. I have seen conflicting info on this? Thanks again.
I got my scren unit from ebay, and it included a torx driver and a plastic case tool. I honestly can't remember what size came in the kit, because I used my own torx set. Im pretty sure its just the one size, though.
Good luck!
You might find this information interesting.
http://forums.wireless.att.com/cng/board/message?board.id=cingular&thread.id=116836
Disregard ............
i always replace only the touch screen. okay i've done it aprox 30 times. But i never broke one.
if you decide to replace only the touchscreen, there are 2 types. thus check which on you have, and i found out that sometimes reassamble, and cleaning can help.
good luck.
torx is 5 and 6, 6 for opening the back of the phone, 5 for the screen part removal of the body and opening it. you need an opening tool!!
adhesive
is there a terrible adhesive between the screen and digitizer, as the second poster mentioned? how difficult is it to deal with?
just cut away with snapoff knives. It wil break in more pieses. (the glas that is) just be carefull, and take your time
Thanks
Thanks for all of the info, i went ahead and purchased the screen with the digitizer and tools. One thing i have noticed though is the d-pad has stopped working also, i'm using a custom rom so i'm not sure if it's just that or it's something else. i will prob re-image after i replace screen.
Abel2007 said:
just cut away with snapoff knives. It wil break in more pieses. (the glas that is) just be carefull, and take your time
Click to expand...
Click to collapse
Well, guess I was a smarty pants and bought my stuff before consulting XDA...as such, I ONLY bought the touchscreen rather than the entire new unit. Cheaper, yes, but I had no idea about the adhesive until just now. My only question is, once I remove the old screen from the LCD with a razor blade, how do I affix the new one?
Anyone?
i would love to know this too because i have to also replace my digitizer!
drokkon said:
Well, guess I was a smarty pants and bought my stuff before consulting XDA...as such, I ONLY bought the touchscreen rather than the entire new unit. Cheaper, yes, but I had no idea about the adhesive until just now. My only question is, once I remove the old screen from the LCD with a razor blade, how do I affix the new one?
Anyone?
Click to expand...
Click to collapse
I used rtv gasket maker the transparent blue one worked well.
you can find it in automotive section. Actually any silcone will work.
also can use double sided tape but needs to be very thin
I've already changing my digitizer, but it doesn't seem to work. So I've change the whole part. cost me $20 more on ebay.
my advice is to change the whole package with the lcd too.
Hi Guys!
I had sent my Xperia to the service center some 14 months back for an LCD change. Now I wanted to change the housing with something I bought off Ebay. The background is necessary because, once I pulled out the 2 small plastic studs next to the camera lens - there were no screws inside! Anyhow I opened the case and found the bottom screw (beneath the antenna) is missing also And my last shock was the sliding apparatus has four screws, in my case another one was missing
Needless to say I am chagrined beyond words! Can some wonderful person here guide me as to how to get these screws replaced? If someone can give me the list of all screws used in the phone (I believe these screws have some codes or something), and where to buy them - I would be highly obliged.. Looking forward to your support.
PS: I still LOVE my Xperia after almost 3 years of rigorous usage.
This morning I was cleaning my phone (getting rid of the finger prints/smudges) while standing up when it slipped out of my hand and hit the tiled floor. Everything is fine except the screen (which is cracked). Screen works fine but is unresponsive no matter where I press or touch the screen. How much does a Z3 Compact replacement screen cost? I searched around and it seems it is about $100?
Screen replacement costs in Poland +/- 135$
(authorised sony service)
Yes' it's hard to get original one cheaper than 100-120$. You can search for some Chinese replacement cause sometimes it looks quite similar to original one but You must check it before buying. Last time I had a client with Z1c replacement screen which he bought for 40$ and there was no white color, everything what should be white was purple.
Voids warranty, cheap replacement
Got mine from here replacebase dot co dot uk (can not post links ), of course you void your warranty if you do it yourself.
Parts are good quality till now. I advice to order a back glass too, I broke mine when taking it out and had to reorder again (costs approx 6 pound).
Next time just heat up back glass with hair dryer and You wont break it.
Chamelleon said:
Next time just heat up back glass with hair dryer and You wont break it.
Click to expand...
Click to collapse
Thanks for the input
The problem was a small crack which did not matter until you have to remove it, you can not pull on it when its cracked. Anyway I will use a hair dryer to put it back together (assemble, heat up, press with books).
Thanks for the replies.
I'll be getting the repair done from the official Sony shop/distributor I bought the phone from. Just wanted to get an idea of how much it "should" cost before I approach them.
m4mbax said:
Thanks for the input
The problem was a small crack which did not matter until you have to remove it, you can not pull on it when its cracked. Anyway I will use a hair dryer to put it back together (assemble, heat up, press with books).
Click to expand...
Click to collapse
Hello
I have tried to change my backglass 3 times but after a few hours the glass falls off... (Yes, I cleaned the phone removing all the old adhesive - and yes, I had pressure on it over night ) But all the instructions I have found on the internet never mentioned anything about putting the glass on, and HEATING it up, and the putting pressure on it... Where have you found that advice? You could imagine that heating up would ruin the adhesive/making it thinner and thereby not waterproof...? But on the other hand your succesrate probably beats mine...
Foxhunter123 said:
Hello
I have tried to change my backglass 3 times but after a few hours the glass falls off... (Yes, I cleaned the phone removing all the old adhesive - and yes, I had pressure on it over night ) But all the instructions I have found on the internet never mentioned anything about putting the glass on, and HEATING it up, and the putting pressure on it... Where have you found that advice? You could imagine that heating up would ruin the adhesive/making it thinner and thereby not waterproof...? But on the other hand your succesrate probably beats mine...
Click to expand...
Click to collapse
I think it was a comment below the iFixit tutorial. But one big warning here, I did extra maximally stupid and put it to 'press' under my table (with books around it). The table was too heavy and cracked my front screen once again :crying:
+ The rear glass sits fixed and has not loosened.
- Don't put too much pressure or you destroy it yet again like stupid me
m4mbax said:
I think it was a comment below the iFixit tutorial. But one big warning here, I did extra maximally stupid and put it to 'press' under my table (with books around it). The table was too heavy and cracked my front screen once again :crying:
+ The rear glass sits fixed and has not loosened.
- Don't put too much pressure or you destroy it yet again like stupid me
Click to expand...
Click to collapse
Doh!!! ? I have also read on Ifixit and can see there are different opinions about if it is nessesary to heat or not. But I think I will follow your advice and heat the new back before putting it under (less pressure) ?.
Another thing I read on Ifixit is that someone writes that you should put on an adhesive sticker - eventhough the new back comes with adhesive already on...? What is your advice on this?
Most pre-glued adhesive stickers on back are useless. Now everytime I change back in Xperia Z, Z1, Z2, Z3 and compacts I need to remove pre-glued sticker and change it to original one. Many times I had complaint on it from my clients saying that back glass came off. So it's better to order original back glass or just original adhesive.
Foxhunter123 said:
Doh!!! I have also read on Ifixit and can see there are different opinions about if it is nessesary to heat or not. But I think I will follow your advice and heat the new back before putting it under (less pressure) .
Another thing I read on Ifixit is that someone writes that you should put on an adhesive sticker - eventhough the new back comes with adhesive already on...? What is your advice on this?
Click to expand...
Click to collapse
Good
Mine came with the adhesive ON the screen, I used that one, I didn't have a separate one. Be extra careful when 'placing' the adhesive where it belongs because you can not remove it once place (okay maybe slightly). Its important that it fits on the first to first and a half try. More adhesive means thicker layer --> glass will stick out
Anyway, most of the stories you read online are partially BS, the phone will work even when the glass is a tiny bit loose or when the adhesive rotated and is a bit thicker in one place. In my eyes, when you dared to order, you are very much capable of assemble the parts.
In btw, ordered new glasses today, hope my two left hands fix it this time.
PS: A lesson I learned on a friends Galaxy S2, do NEVER EVER try to use force when something sticks or is not as loose as in a video. Google or ask another person maybe you just dont do the trick. A connector didnt want to come off so we used a lever to lift it, CLICK, the place where the lever levered broke the board... :silly:
Edit 1: I think its not necessary to HEAT it, it just has to be a lil bit warmer than in your pocket or when calculating heavily. 30s under a hairdryer will be more than enough i guess.
Forgot to update this thread. I received my fixed phone last week. They replaced the screen and even the "bumpers" around the phone for $98. They even delivered the phone to my home free of charge. Looks brand new, all the minor dings I had on the phone are gone.
On another note, I also bought my first iPhone. Got an Space Gray iPhone 6s 128 GB with the official/Apple leather case for the 6s. Got it last Thursday. Been playing around with it a lot and, overall, I love it. Deciding on whether to keep my Z3 Compact as a back-up phone or just sell it. But geez, does the iPhone 6s load games and other apps fast (thanks to its NVMe storage).
Hey Guys,
i have a problem with my Z3compact.
My Display comes up on one site corner so i have to fix it again with some special glue.
I've watched some Videos how to change the display completely but then i must dismantle everything in the phone from the back.
This is a lot of work.
Is there a way to fix the display from the front without dismantle the back?
Can i heat the Display carefully and lift it of for some Millimeters. Is the connector cable long enough to do it?
Then i would take the glue and fix it again.
Or is there no chance to do so?
Thanks for Help
OK today i made it.
It is possible to lift up the display for some millimeters.
Thats enough to clean the old glue and put the new one on it.
Now i have to wait until the glue is safe.
First little Test i made everthing works.
what kind of glue did you use?
darxider said:
what kind of glue did you use?
Click to expand...
Click to collapse
i think he used water with sugar from shop. no glue will resist more than some months bcs this phone is a little cripi sh*t from japan of kabushiki....also no adezives with 1 dolar or 2, dont save us...
Hi everyone . I would like to share with you my experience during the dismantling of the redmi note 10 pro last night I started to remove the backplate to access the phone I noticed that the motherboard had very little thermal paste so I took the liberty of adding it. is I also removed the front camera which I no longer use it does not help me in reality. Is I also unplug the fingerprint sensor sight that I do not use it I liked to think you that I can remove the motor linear ?
Take note m'y phone didn't overheat and CPU throthling test is very stable why Xiaomi does not add more thermal paste
Can't wait for the post in a week or two when your phone is hardware bricked...
Can't wait for your next post regarding how to remove excess thermal paste from your phone's motherboard.
ralphpaPIPS said:
Can't wait for your next post regarding how to remove excess thermal paste from your phone's motherboard.
Click to expand...
Click to collapse
I see you didn't trust me I'm starting to doubt what I did. finally speaking of surpluses I opened my phone to check is unfortunately cella overflowed I have to pay with a container of alcohol .
But do you think the alcohol is really dangerous for the motherboard think you that I said obligatorily to use the isopropyl alcohol to rate the components of my phone.