Dear Community,
after changing my display due to an unfortunate meeting between my device (Honor Play) and the floor, the device won't turn on again and is showing, what seems to be an error code via the status LED (green and yellow in short succession followed by a long green light).
I changed the display myself, following video tutorials and did not encounter any obvious problems. Additionally I installed a new battery. Both new parts are originals. The display was tested beforehand and worked fine. After testing, I removed the broken display, replaced it and the battery and put the phone back together.
Trying to turn the phone on results in a short vibration and an error code of the status LED. Green and yellow is flashing in quick succession, followed by a longer green light. Total duration of the code is approximately 2 seconds.
Unfortunately I could not find any documentation on that code, so I have a real hard time pinpointing the problem.
Until now I cleaned and reconnected all connectors to no avail. They also seem to connect firmly.
Holding down the power and vol-up or vol-down buttons to reset the phone change nothing.
The phone was charged for more than an hour now. Reconnecting the old battery (formerly working), did yield the same result.
I am at wits end and hope that some of you might have an idea...
Thank you!
Muppel
Related
Well, I think I have finally managed to kill my PDA2k. It was a late night and long story short, it got wet (but not too wet).
The next day, I plugged it into a usb power supply (car charger) and it would begin to boot (displayed the info at bottom right screen) but would fail when it tried to load the OS. I waited for a bit a re-tried a few times. Then the red light came on (top right led) and it no longer even attempts to boot. I disassembled it and made sure everything was dry and clean and it still just turns on the red light and does not attempt to boot.
So, does anyone have any other thoughts/suggestions?
I'm going to go ahead and be prepared for the worst and assume that it is in fact, done. What should I do with it? I do have an insurance policy on it (via State Farm) but I'm not sure if that is covered.
Anybody know of some cool DIY projects to make use of the parts? Or just fun ways to say "farewell" to a phone?
Well sweet moogly googly, it started working again!!! I just left it on the charger for a while and the red light went off...then I hit reset and it booted just fine!
Its like Christmas came about 15 days early...I hadn't made a backup of my data in a LONG time.
If anyone looks over my posts history, they'll see that there have been several "close calls." But I guess this is just a testament to HTC and their ability to build "resilient" hardware.
Well all is not well in PDA2K land...again.
The last post was a bit premature as it is having some serious issues. First, I cannot communicate (hear/talk) on any phone calls. I can make and receive calls fine, but no audio coming or going (despite sounds and recording working). Second, I am unable to connect via ActiveSync (or even mtty), so I can't reflash to see if that is the issue. Third, although it is becoming less frequent, the device will just power off and the red led will come on. After a few seconds the light will go off and it can be restarted. Last, the power button does not work at all. So even when it is working, there is no way to turn off the screen (without using a program).
One other related note: when you do a reset it loses the date/time.
All in all, it seems as though it is very rapidly becoming a glorified paperweight. Any ideas? If not, I'm back to deciding how to send it to "gadget heaven."
Would anyone has any use for the hardware?
Hey all,
I just installed a new digitzer on my Vivid. Everything went fine, and nothing broke as I was taking apart the phone, or putting it back together.
Now that the phone is back together, however, it is having some problems.
First off, When I try to power the phone on, it vibrates like usual, but then doesn't display anything. The phone then proceeds to enter in to a bootloop and keeps vibrating every couple moments. When plugged in to the computer, the orange light comes on for a few seconds, then turns off. Windows will not recognize the phone. All the while, the screen is completely black, and none of the lights come on for the buttons either.
The phone was working fine before replacing broken digitizer.
The phone is NOT rooted, nor has it ever been. I am running stock ICS.
have tried entering Hboot with no avail.
Any advice?
Thank you!
Can you get into any other modes? Try to get to hboot(hold down power button and volume down) while plugged into computer. Should take it to fastboot.
how long for? I tried holding down for a good 30 seconds...nothing happened other than my orange light turning off
I noticed with mine I had to go with:
Remove battery.
Replace battery
hold vol down + power
few seconds later release power
few seconds later in hboot
YMMV due to repair.
You can also try a knoppix boot disc and some tutorial to see if you can find any sign of life off the phone in dmesg.
hope this helps some.
Sounds like a loose connection. Make sure that you've correctly reconnected all internal connections. Especially the connection under the little door with the void sticker on the screw in the battery compartment. If after verifying all connections are made and proper, the problem persists, I'm sorry to say you may have physically damaged the connectors during disassembly. Please visually inspect all connections for damage. A powerful magnifying glass is recommended.
(I have successfully replaced my digitizer twice, and my LCD panel once on this phone...)
Sent from my HTC Dark Raider using XDA.
I have taken it apart twice, checked all connections, and everything is good. Phone cannot enter any boot mode, and computer still doesn't recognize it. The orange light still only stays on for a few seconds when plugged in, then turns off. The phone then proceeds to keep trying to restart itself, but the screen remains pitch black blank
idk.. get a replacement.?
Hello !
My problem is a bit long to explain, but I'll try to make it short ^^
So, at the beginning, I think the problem is about water resistance, because I put it in water with all the covers closed but when I took it back, the jack's "white thing" turned red and so did the others as well (even if I don't know how it happened).
From that moment, I began to try a lot of things, like charging it, connecting it to the computer, put it in rice during one night, etc... In order to dry it and to see how it's reacting, and here is the differents "states" I noticed:
-when it was charging with the wall charger, the red LED was blinking regularly
-when I connected it to my computer, the red LED turned on, my computer made the connected sound, the LED turned off 2 seconds after, and 10seconds after it went on again with the disconnected sound and the connected sound again and repeating (disconnected - LED on - connected - 2sec - LED off - 10sec)
-it wasn't doing that usually but it did it one time; red LED blinking without any connection to anything ( blinking 2 times every 2 seconds)
-and nothing was happening with the dock
At the moment I'm writing, it's acting a bit different:
-nothing's happening whithout connection
-when charging to the wall charger or the dock, it vibrates 1 time, red LED turning on, waiting 4 seconds, vibrating 3 times pretty fast, then the LED is turning off and it repeats a dozen of seconds right after that. (a bit like that - --- - --- - --- - --- - ---)
-when it's connected to the computer, it's now doing the connected and disconnected sound without stopping just like somebody is playing with the USB
I tried to press any button at any state, but I did'nt noticed anything changing.
I think that's all.
So if you have any idea about what's happening to my phone, please tell me
Thank you !
...
It's water damaged and needs sending for repair. Red LED indicates a hardware error.
There is nothing you can do yourself to repair it.
Sent from my Hudl HT7S3 using Tapatalk 4
So, yesterday, I brought it to a repairer but instantly when he saw that the "little squares" were red, he told me that there's nothing to do, end of discussion.
I came back home a bit sad because I knew I had to buy a new phone but then, this morning, I was in a mood like "I don't give a f***" so I put it in charge and I tried hard with the Power Button, and the Vol+/- when suddendly, I saw the screen blinking during one short moment. Then, I tried again and I finally saw the "Charging screen" but the screen was going on and off. I waited a bit and it turned on by itself, and it went until the PIN-code phase but there again, the screen was turning on and off repeatedly, and, trying hard again with the buttons, I managed to go until the homescreen, but seeing the screen turning on and off again with sometimes the menu to power off the phone/restart/etc... I realised that the real problem was about the buttons ! So I turned it off ( trying to press the button rapidly before the screen do it again) and now I finally understood evrything ! When it was doing the strange patterns with the LED and the vibrations, it was because there is some problem in the contact with the buttons (it was turning on and resetting by itself because of this).
Now that we finally know what the problem is, have you got an idea about how to solve it ? Do you think there is still some water around the buttons and that I should try to dry it again (and how in that case ? Rice ? Hair-dryer ?) ? Or will the buttons stay like that even without water remaining ? In that case, do you have any solution ?
Thanks again !
You can buy all the replacement buttons on ebay if you are confident enough, it seems that you're warranty has been voided by the water so that's out of the question. I would suggest buying a new battery at the same time.
replace the battery ..
S.P.F said:
So, yesterday, I brought it to a repairer but instantly when he saw that the "little squares" were red, he told me that there's nothing to do, end of discussion.
I came back home a bit sad because I knew I had to buy a new phone but then, this morning, I was in a mood like "I don't give a f***" so I put it in charge and I tried hard with the Power Button, and the Vol+/- when suddendly, I saw the screen blinking during one short moment. Then, I tried again and I finally saw the "Charging screen" but the screen was going on and off. I waited a bit and it turned on by itself, and it went until the PIN-code phase but there again, the screen was turning on and off repeatedly, and, trying hard again with the buttons, I managed to go until the homescreen, but seeing the screen turning on and off again with sometimes the menu to power off the phone/restart/etc... I realised that the real problem was about the buttons ! So I turned it off ( trying to press the button rapidly before the screen do it again) and now I finally understood evrything ! When it was doing the strange patterns with the LED and the vibrations, it was because there is some problem in the contact with the buttons (it was turning on and resetting by itself because of this).
Now that we finally know what the problem is, have you got an idea about how to solve it ? Do you think there is still some water around the buttons and that I should try to dry it again (and how in that case ? Rice ? Hair-dryer ?) ? Or will the buttons stay like that even without water remaining ? In that case, do you have any solution ?
Thanks again !
Click to expand...
Click to collapse
How is it now?
S.P.F said:
So, yesterday, I brought it to a repairer but instantly when he saw that the "little squares" were red, he told me that there's nothing to do, end of discussion.
I came back home a bit sad because I knew I had to buy a new phone but then, this morning, I was in a mood like "I don't give a f***" so I put it in charge and I tried hard with the Power Button, and the Vol+/- when suddendly, I saw the screen blinking during one short moment. Then, I tried again and I finally saw the "Charging screen" but the screen was going on and off. I waited a bit and it turned on by itself, and it went until the PIN-code phase but there again, the screen was turning on and off repeatedly, and, trying hard again with the buttons, I managed to go until the homescreen, but seeing the screen turning on and off again with sometimes the menu to power off the phone/restart/etc... I realised that the real problem was about the buttons ! So I turned it off ( trying to press the button rapidly before the screen do it again) and now I finally understood evrything ! When it was doing the strange patterns with the LED and the vibrations, it was because there is some problem in the contact with the buttons (it was turning on and resetting by itself because of this).
Now that we finally know what the problem is, have you got an idea about how to solve it ? Do you think there is still some water around the buttons and that I should try to dry it again (and how in that case ? Rice ? Hair-dryer ?) ? Or will the buttons stay like that even without water remaining ? In that case, do you have any solution ?
Thanks again !
Click to expand...
Click to collapse
yeah i think my problem is buttons too.. after i wash it, with flaps closed tightly, my volume indicator increases automatically and constantly.. and after a while it will take a rest and annoy me again.. my power button doesnt respond too.. until it opened in safe mode.. to cut it short, my phone wont boot and whenever i charge it it vibrates with a pattern 1 short and long stop and 3 short and so on
i think the buttons is pressing power button and volume up by itself when it is charged.. pls help
Hello everybody,
I'm not an expert in android or any other phone software, that's why I kindly ask you for help.
Trying to install an air company application from Play store on my desire 500, I got a message saying there is no enough memory to install it. The phone froze with this screen without any reaction on touching, sweeping etc. The only thing I could do was to restart it. After initial screen and entering SIM card PIN code the home screen appeared and began blinking at uneven periods of 0.5 - 1 s. It wasn't possible to control it in any way. Yet, the phone became hot and quickly drained the battery. I removed the battery, put it back, charged it and turned on the phone - it showed the same behavior. After 200 attempts I managed to unlock the screen and to make it operative. Didn't find anything suspicious except that it's hot, takes more current than the charger could supply (battery diagram goes down although charging is on) and reacts very slowly on touching and sweeping. When connected to computer HTC sync manager starts automatically but doesn't establish connection (No phone connected). After expiring wake time and the screen gets black and power button is pressed, the same blinking appears.
I made a hard reset (luckily I have a backup) but nothing changed even the phone is now completely naked, as came from the shop, without additional apps, files, contacts, nothing.
Please advise what could I do to solve the problem. This is my only phone and I can't afford a new one.
I could give all info I have concerning firmware, OS etc.
Thanks in advance!
Best regards
Emil
P.S.
Android 4.1.2
Build 1.34.901.2 CL364226
Kernel 3.4.0-g996394e
Hello, members. I come here to ask your help because i haven't found any solution for it anywhere on the internet. This is what happened: some days go (around a week or two) i updated my security patch to the last one released by Motorola and the phone was OK, pretty much the same. Then around five to six days ago the problem started: my phone started going off even with full battery, and so i had to hold high volume key + power key for the phone to boot again (this happened twice and was "solved" by the time) and so the headache started. Around four days ago i went to sleep and left my phone charging, then when i woke up some hours later it was completely off, showing nothing on the screen, then i removed the charger and turned it on, and for my surprise the phone booted saying Hello Moto, vibrating and all but the screen showed absolutely nothing but a black/grey screen, not even the boot logo was shown. Once the phone started i noticed the screen touch is working for turning on the flashlight, receiving or rejecting calls and all, but it is completely dark. I have already tried lighting up a flashlight in front of its light sensor to see if the ambient display was active, but it is not. I have also tried turning it on by holding low volume key + power for a lot of seconds and it resulted in no changes. I have tried turning it on by holding high volume key + power key, and even low + high + power keys simultaneously for tons of seconds and NADA. I'm completely desperated because i have found no solutions for it at all anywhere. My phone has not fallen to the ground and neither got watered, so i don't know what the **** has happened to it. It got like this completely out of a sudden, no one even touched it.
I had the same issue with my moto g6 and it happened a few days ago. i unlocked bootloader and rooted the phone and then installed some apps . it happened 2 times. First time happened i solved it. While it was charging screen went black and nothing appeared on screen but phone was working . i called from another phone and it was ringing. I thought an app was causing this issue so i uninstalled some apps that i installed when i got the phone. I turned it off and waited for a while to cool down ( i thought it was heated from over charging ). When i turned on it was ok everything came back. Week later it did the same issue but this time it was completely gone. I removed back cover to check battery . I disconnected the battery and then connected again , turned on the phone , screen was going on and off. After turning it on it stayed around 10 min. and then again everything gone. People who had similar issue are saying hard reset or fastboot mode etc. but nothing appears on screen so how can i do hard reset when i do not see anything on screen. Right now it is unusable . I cannot do nothing with the phone.
I fixed this problem on my G6+
The screen went black after the phone being in the hot sun for a while. I believe the problem was due to a poor connection to the screen because when I pressed hard at the very bottom of the screen the display flickered on. I then pressed very hard at several points along the bottom of the screen and the screen then started working constantly again. Not really a proper fix but I now have a working display again.
---------- Post added at 12:17 AM ---------- Previous post was at 12:12 AM ----------
The screen went black after the phone being in the hot sun for a while. I believe the problem was due to a poor connection to the screen because when I pressed hard at the very bottom of the screen the display flickered on. I then pressed very hard at several points along the bottom of the screen and the screen then started working constantly again. Not really a proper fix but I now have a working display again.