Related
Nightmare.
Got my Diamond today, and charged it up.
It ran out 5 minutes ago, so I plugged it into the mains charger.
It vibrates, shows HTC and then gets stuck in a constant reboot. It's like it gets a little charge, uses it, then restarts the process.
I guess the battery is so dead that even the mains charger cant give it enough boost to start charging.
Help Please
If you only got it today then id be sending it back as it seems to be a faulty unit. Perhaps someone can give you a fix but if it was me, id be demanding a new working unit...you just never know what other faults the phone might have.
Good job I didn't Hard-SPL it straight away.
Damn, Always happens to me.
Are you trying to charge it with the wallcharger or by usb to a computer.
Beacuse if you are doing it by the computer there is an option on the phone that disables charging when conected to the computer.
Good luck dude.
Definately wall charger.
I think it's f(***d
I'll go back to my Kaiser and wait for the Raphael I think.
i would first try to charge the battery device turned off!
i noticed that the led in center button does not blink in the beginning but it should charge!
after a while try a hard reset!
Tried the following:
I cant switch off the device as soon as power is applied via USB it switches on. Tried holding the power button down but nothing.
Tried entering bootloader but same reset loop.
Tried hard reset, gets to grey screen with blue text but then reset loop again.
I tried leaving the battery out for half an hour and trying again but soon as usb is in it powers up and reset loop.
I put a multimeter on the battery and it is dishing out 3.7v as expected.
I think the device is knacked, even though I was using it for most of the day.
laporte said:
i would first try to charge the battery device turned off!
i noticed that the led in center button does not blink in the beginning but it should charge!
after a while try a hard reset!
Click to expand...
Click to collapse
Usually a hard reset solves everything (hopefully)
Sergio PC said:
Usually a hard reset solves everything (hopefully)
Click to expand...
Click to collapse
Tried hard reset, gets to grey screen with blue text but then reset loop again.
Nope
leave it charging for at least 10 minutes before turning it on.
bakman said:
leave it charging for at least 10 minutes before turning it on.
Click to expand...
Click to collapse
I cant switch off the device as soon as power is applied via USB it switches on. Tried holding the power button down but nothing.
don't even touch the power button!
the device should not start if you touch nothing and just plug the powercable!?
i don not think that you press the powerbutton accidentally while plugging the cable, i hope i'm right?
Without touching the power button, I plug in the charger and the phone vibrates and starts.
From dead:
1. Plug in charger
2. I get 2 swirls of white on the round button thing
3. Phone vibrates
4. Smart mobility logo shows
5. Phone reboots
GOTO 1:
i miss the touch diamond screening with rom version etc.
normally it shows up before the htc smart mobility screen.
i don't think the battery is the badguy. seems more a fault in ipl or spl?
You're right.
I was wrong when I said smart mobility.
It comes up with TOUCHDiamond across the centre of the screen and right where the little red numbers USUALLY appear in the bottom right, it reboots before that.
To perform a hard reset
1. Pull out the stylus.
2. With the device turned on, press and hold the VOLUME DOWN and ENTER buttons, then press the RESET button with the stylus tip.
3. Release the RESET button, but continue pressing the VOLUME DOWN and ENTER buttons until you see message on the screen
4. Release the VOLUME DOWN and ENTER buttons, then press the VOLUME UP button to perform the hard reset, or press any other button to cancel the reset
save this info on your computer
Sorted!
I left the battery out overnight, and when I came to work this morning, I plugged it into the charger and it didn't automatically start up so it got a good 3/4 hour charge which then enabled me to fire it up for a full charge.
congrats! i hope for you that this problem doesn't come back!
Sounds to me like it also could have been the power button was jammed pushed in. Maybe leaving it for a while without pushing the button did the trick, allowing it to release itself.
In case that was the problem, keep an eye on the power button in case it seems to be a bit dodgy. If it is going to do it again, then you want to swap it immediately for a replacement brand new unit. After a while, if you try to swap it out, they will give you a refurbished unit, not a brand new one!
Of course it could have just been a software bug, that was cleared by letting it fully power down (as others have said).
Just make your decision quick before you end up with a refurbished model for replacement.
Just to let you all know.
Over the weekend I fully charged my Diamond, and without even making a phone call or using WiFi, Bluetooth or anything the battery lasted 1.5 hours.
It's gone back to clove now for a replacement.
I've seen a few people having this issue so I advise getting it back for replacement asap.
My diamond got very hot during normal use (without charger). Is that normal? Not the battery but the actual device.
NOTE - I added this post here thinking the CM9 experts could help. I then realized it should be in the Q&A section. If this does not belong here, I ask a moderator to please delete it.
I have been running CM9 nighties for some time now with no issues on my 16GB US WiFi only Touchpad. I installed TWRP and after some time decided to remove it and just use CWM. After trying several things from the posts (which would not work) I decided to remove CM9 completely then reinstall. This is where I got into trouble...
I loaded all necessary CM9 files in the cminstall folder on the Touchpad. I successfully ran ACMEUninstaller and got back to the WebOS language selection (i.e. the initial WebOS screen from factory). Instead of logging into WebOs (felt there was no-need since I never use it), I put the unit in Download mode (vol down + power). I then ran ACMEInstaller2. I received an error (text on the black touchpad screen which I assume is the bootloader) saying the needed files were not installed and something like "remove the wall". I thought I would reboot the unit and now log into WebOS and reinstall the CM9 files (thinking I made a typo when loading them). Now I cannot get the Touchpad to reboot - totally black and even when connected to the PC I dont get the USB connection sound.
Does anyone know if there is a hardware method to bring the unit back (maybe a different sequence of button presses or shorting a pin on the USB connector)? I have tried home+vol up+power, home+vol down + power, home + power, and of course power only and home only. Each combination was held for 30 seconds and then again for a minute and with power connected, PC connected, and nothing connected to the USB port.
Any thoughts would be greatly appreciated.
Resolution: In a post I saw dated May of 2012, the user indicated HP was still honoring their warranty. I contacted HP via their Chat service, after giving them my model and serial number, I was told I had three weeks remaining on my warranty. HP sent me the return box with authorization and in a week I received (what seems to be) my exact Touchpad... only now it booted just fine. I have since reinstalled ICS and am running fine. Thanks to all who responded. I wanted to share this as I am extremely impressed with HP's warranty service (no questions were asked if I had rooted the device, where I bought the device, etc).
I remember this happened on my brothers and what it was is that the battery was completely dead. I believe it has a backup that needs to charge before the main one. That's the only time I have personally seen this happen. Perhaps if you leave it on the charger for a while it will boot and u can use web os doctor to get it to stock.
Live and Die on this day....
chozyn said:
I remember this happened on my brothers and what it was is that the battery was completely dead. I believe it has a backup that needs to charge before the main one. That's the only time I have personally seen this happen. Perhaps if you leave it on the charger for a while it will boot and u can use web os doctor to get it to stock.
Live and Die on this day....
Click to expand...
Click to collapse
Thanks, I let it charge all night then tried it this morning (as described not just powering it on). Of course, with only a black screen I can't tell what the charge is. I have checked the cable and am now using a different power supply in case that had failed. I think because this happened during the removal/install process I scrogged something in the bootloader?
enmriley said:
Thanks, I let it charge all night then tried it this morning (as described not just powering it on). Of course, with only a black screen I can't tell what the charge is. I have checked the cable and am now using a different power supply in case that had failed. I think because this happened during the removal/install process I scrogged something in the bootloader?
Click to expand...
Click to collapse
It's a good idea to use only stock cable and charger.
Sent from my ClassicJewel
enmriley said:
Thanks, I let it charge all night then tried it this morning (as described not just powering it on). Of course, with only a black screen I can't tell what the charge is. I have checked the cable and am now using a different power supply in case that had failed. I think because this happened during the removal/install process I scrogged something in the bootloader?
Click to expand...
Click to collapse
Are you able to get into download mode at all?
A$$h4t said:
Are you able to get into download mode at all?
Click to expand...
Click to collapse
No, totally black device. I was hoping at least I'd get the USB connection on my PC, but not even that.
enmriley said:
No, totally black device. I was hoping at least I'd get the USB connection on my PC, but not even that.
Click to expand...
Click to collapse
This happened once to my TP when I first put CM7 on the device a while back. I woke up one morning, forgot to plug it in overnight and it had died. No response to any charger, I was getting worried but then I found a solution. With it plugged in, hold the power button and home button down together for 15 to 30 seconds. It was that or hold the power button down and keep pressing the home key over and over. Not 100% sure, but it came back to life and I remember it took me a couple tries. Try holding both down simultaneously for 30 seconds or a minute, if that doesn't work, push and hold power first then home right after and hold both for 30 seconds.
Okay.... hard reset has been a life saver for me. Hold the home button down, then press and hold the power button, so you will be pressing them at the same time. Keep holding them till you see the HP splash screen, it may take a few min and seem like nothing is happening. I thought I fried mine the first day I got it, but this worked for me!
Good luck!
And, if you decide that does not work for you there is such a thing as the WebOS doctor which will get you back to stock. Link here: http://en.m.webos-internals.org/wiki/How_To_Recover?wasRedirected=true
-SGA- said:
Okay.... hard reset has been a life saver for me. Hold the home button down, then press and hold the power button, so you will be pressing them at the same time. Keep holding them till you see the HP splash screen, it may take a few min and seem like nothing is happening. I thought I fried mine the first day I got it, but this worked for me!
Good luck!
And, if you decide that does not work for you there is such a thing as the WebOS doctor which will get you back to stock. Link here: http://en.m.webos-internals.org/wiki/How_To_Recover?wasRedirected=true
Click to expand...
Click to collapse
This post should do the trick for you....just press the power and home buttons at the same time, hold them down for about 30 seconds until you see the HP logo on the screen then release them...good luck!!!:good:
rhidalgo1973 said:
This post should do the trick for you....just press the power and home buttons at the same time, hold them down for about 30 seconds until you see the HP logo on the screen then release them...good luck!!!:good:
Click to expand...
Click to collapse
Nope... As stated in the OP, "I have tried home+vol up+power, home+vol down + power, home + power, and of course power only and home only. Each combination was held for 30 seconds and then again for a minute and with power connected, PC connected, and nothing connected to the USB port."
I need to know if ACME Installer is doing anything in the Bootloader. I have flashed and reflashed CM7, CM9, and multiple ROMs. Even uninstalled CM all together when I went from CM7 to CM9. I am familiar with getting into Download Mode and the hard reset (which apparently isn't solving this issue).
I appreciate the feedback, just hoping someone familiar with the Bootloader and Touchpad partitions can help out.
enmriley said:
Nope... As stated in the OP, "I have tried home+vol up+power, home+vol down + power, home + power, and of course power only and home only. Each combination was held for 30 seconds and then again for a minute and with power connected, PC connected, and nothing connected to the USB port."
I need to know if ACME Installer is doing anything in the Bootloader. I have flashed and reflashed CM7, CM9, and multiple ROMs. Even uninstalled CM all together when I went from CM7 to CM9. I am familiar with getting into Download Mode and the hard reset (which apparently isn't solving this issue).
I appreciate the feedback, just hoping someone familiar with the Bootloader and Touchpad partitions can help out.
Click to expand...
Click to collapse
If the battery was low when you got into this state then it could be that there is not enough power to even let the charging circuits work properly. WebOS has better protection against getting into this fix.
I experienced this once and the trick that fixed it for me was to connect the standard micro USB to the Touchpad and use the standard HP charger unit. Then repeatedly remove the big USB from the charger, wait about 5 seconds then plug it in, wait about 10 seconds and repeat the cycle. After about twenty goes I was rewarded with the battery low icon and it started charging again. I think the theory behind this trick is that when you first plug the power in the battery gets a bit of charge before the circuits kick in, detect very low battery and stop the charging cycle. Doing it enough times gets enough charge into the battery to kick start proper charging.
Now I am not saying this will fix your problem but it might be worth giving it a go.
To prevent myself ever getting into this state again indavertently I now have Tasker set up to shutdown the whole device if the battery level drops below 8%.
bobtidey said:
If the battery was low when you got into this state then it could be that there is not enough power to even let the charging circuits work properly. WebOS has better protection against getting into this fix.
I experienced this once and the trick that fixed it for me was to connect the standard micro USB to the Touchpad and use the standard HP charger unit. Then repeatedly remove the big USB from the charger, wait about 5 seconds then plug it in, wait about 10 seconds and repeat the cycle. After about twenty goes I was rewarded with the battery low icon and it started charging again. I think the theory behind this trick is that when you first plug the power in the battery gets a bit of charge before the circuits kick in, detect very low battery and stop the charging cycle. Doing it enough times gets enough charge into the battery to kick start proper charging.
Now I am not saying this will fix your problem but it might be worth giving it a go.
To prevent myself ever getting into this state again indavertently I now have Tasker set up to shutdown the whole device if the battery level drops below 8%.
Click to expand...
Click to collapse
Bobtidey
To prevent myself or more importantly my daughters tablet ever having this problem I have now purchased Tasker as recommend by yourself and others. But cannot yet figure out how to setup an automatic shutdown, if you have the time could you possibly advise how to do it . I have read the guide but am struggling any help would be appreciated.
Thanks
sstar said:
Bobtidey
To prevent myself or more importantly my daughters tablet ever having this problem I have now purchased Tasker as recommend by yourself and others. But cannot yet figure out how to setup an automatic shutdown, if you have the time could you possibly advise how to do it . I have read the guide but am struggling any help would be appreciated.
Thanks
Click to expand...
Click to collapse
In Tasker add a New profile and give it a name like Battery_Low
Choose State and then Power for the profile.
In Power choose Battery level and set From to 0 and To to say 8%
Set New Task and do Add give it a name like Shutdown and then pick the Misc category
Choose Reboot and set Reboot type to Shutdown
All done. When battery level drops to 8% or below then Tasker will shut the tablet down. Note it will do this without warning. I think one could probably arrange a pop up warning first but I preferred to keep it simple.
bobtidey said:
If the battery was low when you got into this state then it could be that there is not enough power to even let the charging circuits work properly. WebOS has better protection against getting into this fix.
I experienced this once and the trick that fixed it for me was to connect the standard micro USB to the Touchpad and use the standard HP charger unit. Then repeatedly remove the big USB from the charger, wait about 5 seconds then plug it in, wait about 10 seconds and repeat the cycle. After about twenty goes I was rewarded with the battery low icon and it started charging again. I think the theory behind this trick is that when you first plug the power in the battery gets a bit of charge before the circuits kick in, detect very low battery and stop the charging cycle. Doing it enough times gets enough charge into the battery to kick start proper charging.
Now I am not saying this will fix your problem but it might be worth giving it a go.
To prevent myself ever getting into this state again indavertently I now have Tasker set up to shutdown the whole device if the battery level drops below 8%.
Click to expand...
Click to collapse
I have tried this since your post - thanks. No luck, but will continue to try. I found a post online with disassembly instructions. I think I may try pulling the battery. Looks rather easy... with the right tools.
enmriley said:
I have tried this since your post - thanks. No luck, but will continue to try. I found a post online with disassembly instructions. I think I may try pulling the battery. Looks rather easy... with the right tools.
Click to expand...
Click to collapse
The only way I know is to put it on a Touchstone and after an hour or so it Will come back to life. All thanks to Reverand KYLE. His site is well worth checking out.
Good evening everyone, I have a Nexus 7 8gb, but the thing is, I cannot turn it on now.
It happened as follows:
I was using it every now and then, mostly to read and play.
I was using the charger to charge my cellphone too (XTC Explorer) as it was a lot faster, being 2amp/h.
I updated the cell to 4.1 and at the same week noted the battery wasn't running that long, but blamed it to the rom.
The cellphone also took a lot longer to charge with the nexus charger, yet again I blamed the rom.
I noticed the Nex was at 8% while reading so decided to charge it, but I guess I forgotten.
The next time I wanted to use it it wouldn't turn on. I figure it had no battery.
I plugged the nexus charger to the nexus a whole night and in the morning it still wouldn't turn on.
I figured something must be wrong with the charger, so I tried with the cellphone and nook color charger, but both are .5 amps/hour.
It wouldn't charge, neither connected to the pc (also .5a/h via usb) so I tried a psp go charger, as it is rated at 1.5 amp/hour, much closer.
I connected it at night and saw the charging icon (white on black battery with the ray) and left it overnight.
The next morning it wouldn't turn on either.
I've bought it almost two months ago and I really enjoy it =) but now I'm desperate.
I cannot call google play for the warrant because I'm in Argentina, and I don't believe they will ship me a replacement, nor anything. This one my brother bought from them, but he went back to US a few days ago, and I didn't think of giving it to him to RMA.
I tried keeping the on button, for 5 secs, 30 sec, 90 secs, 120 secs, and no dice. Also tried holding the Up Volume key to restart it, but no chance.
Please help!
Had a similar issue to this over the weekend after not charging for 2 days and the battery going dead. I let it sit on the original charger overnight and for some reason it did not charge. It kept booting and shutting down once it booted due to a low battery warning. It eventually got to the point where the screen would go to fuzzy lines and light but no boot.
To finally get it working I did a combination of a few things but don't actually know what got it going.
Put it on a different (kindle) charger and let it sit for an hour or 2, did several hard resets holding both just the power and also the up/down volume and power all at the same time for up to 60 plus seconds. I switched back to the stock charger and did an additional hard boot by holding just the power for 30+ seconds and it started booting and charging.
I did however put it on the charge again last night and noticed this morning it was still at half battery and didn't get a charge. I ended up putting it on a mifi charger this morning and it's charging again so don't know what is up with the stock charger. Also, have all the latest updates to 4.2 as far as I know as there have been charging issues reported with earlier versions...
Sent from my Nexus 7 using Tapatalk 2
Try this, it just saved my device:
davidcampbell said:
try holding down the volume DOWN and the power key for 10 seconds, then release the power key and keep the volume down key pressed, and it will force the unit to restart into the bootloader from any stage, its effectively like pushing the restart button on the front of a computer and constantly pressing the delete key to get into the bios.
Click to expand...
Click to collapse
I have a new Motorola Atrix HD. I was using it and the screen went black. i hit the power button to unlock but nothing happened. i plugged it in but nothing happened. i took the back off to see if the battery was disconnected. I didn't know the battery was different than other phones and ripped the power cord connecting the battery to the phone when i took it out. lesson learned. Ordered a new battery and installed correctly. phone won't turn on. The green charge light blinks when i plug it into the wall and then stays on for about 20 seconds and then the phone tries to turn on but while the motorola icon is illuminated, it cuts back out and repeats the cycle. I left it plugged in for a couple hours and still the same thing. i tried holding in power and volume buttons for the boot screen. if i do that just as the phone attempts to turn on i can get the screen up and scroll the list of boot options with the power buttons but i can't select any of them and the phone cuts out after the same amount of time. Everytime. When i plug it into my laptop, the light blinks on and then stays on like with the wall, but the phone doesn't attempt to power up. Please, any help would be greatly appreciated. i have read a lot of forums where the battery was acting up because of the chargers people were using. The difference between my situation and those of the people i read about is that my boot screen cuts out and cannot be used. This all happened 2 days after my exchange period ended and because i took the back off myself, best buy won't have anything to do with me so i'm on my own and cannot afford another phone right now. Thanks in advance for your time and concern.
katlic said:
I have a new Motorola Atrix HD. I was using it and the screen went black. i hit the power button to unlock but nothing happened. i plugged it in but nothing happened. i took the back off to see if the battery was disconnected. I didn't know the battery was different than other phones and ripped the power cord connecting the battery to the phone when i took it out. lesson learned. Ordered a new battery and installed correctly. phone won't turn on. The green charge light blinks when i plug it into the wall and then stays on for about 20 seconds and then the phone tries to turn on but while the motorola icon is illuminated, it cuts back out and repeats the cycle. I left it plugged in for a couple hours and still the same thing. i tried holding in power and volume buttons for the boot screen. if i do that just as the phone attempts to turn on i can get the screen up and scroll the list of boot options with the power buttons but i can't select any of them and the phone cuts out after the same amount of time. Everytime. When i plug it into my laptop, the light blinks on and then stays on like with the wall, but the phone doesn't attempt to power up. Please, any help would be greatly appreciated. i have read a lot of forums where the battery was acting up because of the chargers people were using. The difference between my situation and those of the people i read about is that my boot screen cuts out and cannot be used. This all happened 2 days after my exchange period ended and because i took the back off myself, best buy won't have anything to do with me so i'm on my own and cannot afford another phone right now. Thanks in advance for your time and concern.
Click to expand...
Click to collapse
Is it possible that the that connection between the power cord and the phone itself is loose or damaged? I'm just guessing here as I have never opened up the back of my phone.
I would check your battery terminals then leave it to charge if it does. You could also try a factory cable. Another thing would be to try fastboot while connected to your laptop and see if it stays on, and if it does, try reflashing all partitions.
Sent from my MB886 using xda premium
I recently went on a 3 month trip. Before I left, my nook was working perfectly fine, when i got back, it didn't work at all. It's not dead because i left it plugged in overnight but it still didn't turn on. when i plug it in the LED goes from orange to green and then off (or green to orange, i can't remember). The screen doesn't turn on at all. I can't get to recovery either.
This is a Nook HD, I believe it had CM11.
:crying:
Can this be fixed
or should i plan it's funeral
Same here
The same has happened to me. Screen doesn't turn on, but there is power, I can play it into my laptop and something is there, just not enough.
Good excuse for a new tablet!
It can be fixed. I've done it before. It has to do with the fstrim not being compatible with certain hardware versions of our device. If I can remember how I fixed it, I'll post it here. Trying to fix mine (again).
tambourineman86 said:
It can be fixed. I've done it before. It has to do with the fstrim not being compatible with certain hardware versions of our device. If I can remember how I fixed it, I'll post it here. Trying to fix mine (again).
Click to expand...
Click to collapse
If would be fab if you could fix. Seems to be a common issue
I was able to fix it. YMMV.
1) Make sure the Nook is completely off and unplugged
2) Take out your sdcard
3) Hold down power button until the "battery depleted" icon shows, then promptly plug in the power before the icon disappears.
4) Let it set. The screen will go black, then it will attempt to boot and get stuck on the faint black screen, but this time, the charging light should stay amber.
If you want to be safe, wait until the device reboots itself. That could take hours though. If you're plugged into the wall wait at least 30 - 45 minutes before holding the power button down til it shuts down and then rebooting it (with the sdcard inserted).
Good luck, I hope it works for you.
EDIT: Also, I've read this may also have to do with wifi sending the device into some sort of strange bootloop when the screen is off. I personally believe it has more to do with the fstrim of JB but perhaps changing the wifi sleep policy may prevent this issue from happening again. I'm skeptical, but figured I'd pass that info along if anyone wants to try it as well.
tambourineman86 said:
I was able to fix it. YMMV.
1) Make sure the Nook is completely off and unplugged
2) Take out your sdcard
3) Hold down power button until the "battery depleted" icon shows, then promptly plug in the power before the icon disappears.
4) Let it set. The screen will go black, then it will attempt to boot and get stuck on the faint black screen, but this time, the charging light should stay amber.
If you want to be safe, wait until the device reboots itself. That could take hours though. If you're plugged into the wall wait at least 30 - 45 minutes before holding the power button down til it shuts down and then rebooting it (with the sdcard inserted).
Good luck, I hope it works for you.
EDIT: Also, I've read this may also have to do with wifi sending the device into some sort of strange bootloop when the screen is off. I personally believe it has more to do with the fstrim of JB but perhaps changing the wifi sleep policy may prevent this issue from happening again. I'm skeptical, but figured I'd pass that info along if anyone wants to try it as well.
Click to expand...
Click to collapse
Not sure we have the same problem. My screen doesn't come on at all, I don't get a battery depleted icon, no matter how long I hold in the power button. The only sign of life I get is when it's plugged in, when it goes from orange to green after about 10 seconds.
Thanks for the help, but I think it's a lost cause.
YMMV. But mine was the same issue. You should be able to get the icon by holding the power button down for 5 or 6 seconds. I'd say just eff with it until that icon appears. Try different button combinations. I used power and home trying to get the icon to show.
developerbuzz said:
when it goes from orange to green after about 10 seconds.
Thanks for the help, but I think it's a lost cause.
Click to expand...
Click to collapse
Anyway... since people are continually running into this kind of issue...
Give or take 21 seconds after turning orange it turns green during actual boot cycle into rom
Give or take 10 seconds after turning orange is cwm internal recovery.
After about 10 seconds the charging screen image disappears.
The charging screen image once finally no longer may not show up again until full power off/on (holding power button > 10 seconds or full battery discharge). Unplugging and plugging back in does nothing except making the device look bricked if there's too much light shining on it.
Device may not automatically leave the above state under a specific situation(s). May still need manual full power off/on.
Guessing 10 seconds could also be something else during the early/late boot process or other. The light changing color though should indicate that something is indeed happening.
Light should stay green during the boot process if its completely and fully no questions asked 100%. If you go based on that than yours doesn't appear to be completely fully charged which should either mean its turning on and using battery or not charging correctly.
The light turning off is curious. The device could be shutting off. If light comes back on a moment later then the device has rebooted. if the light stays off = n/a.
If its booting into recovery then the device would be available via adb. At that point it could be further evaluated.
On the off chance the screen was damaged it should boot and usb should be available via computer as well as adb.
If not then its probably toast unless its simply not getting a good enough current causing mislead battery stats and/or not enough energy to get to charging screen (bad wall power adapter in use, damaged power cable - though could be bad battery, defect, damage or whatever). OR there's some major error on behalf of the user happening (think should have tried that in the morning not while 1/2 asleep or came home from long trip and forget how that works).
Maybe the only other things are the emmc brick bug, was left sitting in the sun or heat or ocean air or other physical damage/defect even to the power port as well.
Or maybe it was mad that you left it. Shouldn't have hurt its feelings you know. At least its not crying battery acid on you.
That should just about cover everything except for the things not mentioned. Since its your device, you decide what happened.
Its complicated so anyone see any improvements, clarifications, or mistakes? Please put it in a post.
Jsorren said:
when i plug it in the LED goes from orange to green and then off (or green to orange, i can't remember). The screen doesn't turn on at all.
Click to expand...
Click to collapse
Bumping this thread to make it aware that there is a real answer. I have been able to duplicate this problem and rather easily too.
The problem is indeed from bad power. The device isn't receiving the correct amount of power needed to charge and start from a fully discharged battery.
To safely* duplicate this you can use a usb extension that isn't fully connected to the nook power cable. You may need to fully connect it first then slowly disconnect/connect till the light turns green when it should actually be charging. It won't actually charge in this state, or if it is, its very little and the battery percentage will continue to drop.
Leave the cable as is and unplugged. After the tablet is fully discharged, connect the usb cable. The light will change through the modes and turn off. The device will not turn on.
There are probably other ways to cause the problem like for instance a portable usb battery that doesn't put out enough juice (not the orange kind). Etc.
* It didn't hurt mine, but not my fault if it breaks your device.
sandsofmyst said:
Bumping this thread to make it aware that there is a real answer. I have been able to duplicate this problem and rather easily too.
The problem is indeed from bad power. The device isn't receiving the correct amount of power needed to charge and start from a fully discharged battery.
To safely* duplicate this you can use a usb extension that isn't fully connected to the nook power cable. You may need to fully connect it first then slowly disconnect/connect till the light turns green when it should actually be charging. It won't actually charge in this state, or if it is, its very little and the battery percentage will continue to drop.
Leave the cable as is and unplugged. After the tablet is fully discharged, connect the usb cable. The light will change through the modes and turn off. The device will not turn on.
There are probably other ways to cause the problem like for instance a portable usb battery that doesn't put out enough juice (not the orange kind). Etc.
* It didn't hurt mine, but not my fault if it breaks your device.
Click to expand...
Click to collapse
I actually ended up fixing it yesterday!! I haven't touched it in about 3 months, and I was planning on just throwing it out getting rid of it some how. For the heck of it, I decided to plug it in, assuming that it was gonna go through the same process. But this time it went from green to amber, but it never went off. So I pressed the power button and the battery icon appeared. This was a really good sign. So I left plugged in for about 5 to 10 minutes then tried to power on.:fingers-crossed: As soon as I saw that '' Nook" boot up screen, my heart stopped. It booted up perfectly and I almost blew up from excitement :victory:. So I then flashed the stock firmware back onto it, so this would never happen again.
I guess the battery had to be completely depleted or just had to cool down. Idk but either way this was one heck of a miracle
So I recommend for anyone having this problem to just leave it off and don't mess with it. I wouldn't say for 3 months like I did but maybe test it each week or wait a month if you have good patience
Wow. Man, that's awesome! Glad you posted that update on it. Thought if you had posted an update it would be the opposite as in trashed it
Actually, I guess only you could answer if you had also moved/unplugged the power cable from the wall adapter or put it into a different wall adapter, etc. Thinking there could have been a difference there.
These modern day devices are so finicky, guess anything is possible. Like you say, maybe sitting without power is another answer.
From some experimentation I have etermined that your power adapter (that plugs into the outlet) is the issue. It does not like to be leaft plugged in indefinately. It will continually use power even when the nook is not plugged in.
Also, if you use a differnt adapter you will have the same problem unless it is also of the exact same voltage and amps.