Difference between 2020 and 9090 camera program - MDA III, XDA III, PDA2k, 9090 Software Upgrading

Hello,
I have tried to look for a subject on this matter but I found nothing.
I have just bought a qtek 9090 to replace my 2020 and I have notice that the camera is not anymore in full screen when you take a picure like it was on the qtek 2020.
Is there a way to fix this ?
Thanks in advance.

i dont think there is a fix for this.....

Related

Camera problems in spv m2000

HELLO!
I reeved my Spv m2000 today, very good but i cant put the camera to work When i turn on the camera the screen becomes green and freez the PPC ... and i have to hard reset.
Did this Happen to anybody?
Want shell i do to fix this??
Help.....
I miss my XdaII allready
thanks

qtek 2020i ph10c screen will not align after hard reset

Hi i am new to this site so hello peeps...
Anyway i have had my qtek 2020i for about 3 months now and apart from the odd reset (that i have done) its been a useful tool.
Now the other morning it decided to have a freak out and the start menus locked up. I tried to do another reset but nothinge changed..
Now my dilemma is....i performed a hard reset and now the screen will not align...it asks me to tap to set up my device and i start tapping the little crosses but it will not work..i seem to be tapping the crosses for ever with no luck. Can anybody help?
thanks in advance.
Sounds like "Take it back to the shop" time to me.
Something far wrong mate.
Danny-B- said:
Sounds like "Take it back to the shop" time to me.
Something far wrong mate.
Click to expand...
Click to collapse
spot on simple logic i suppose cheers geez
hehe, you could try a rom update or reflash, might be a problem with the rom
I got the new unit it was working fine......then i restored the backup that my last phone took before it went away and guess what....the problem returned :evil: .
Anyway i reflashed the rom with the qtek one and its sorted. :lol:
What is the best rom in your eyes for the alpine device?
The last O2 ROM with Pugs adaption, the 1.3 radio included.
Search for Pug it should come up with a link to his rom.
The newest O2 rom has an older radio version(1.0) because it has Blackberry support (which i will never use)
I am hardly recommend 1.04 radio version. It solved 3 issues for me and made my phone recieve signal better! This is "must have" version of radio!

9100 LCD Problem 60H00032-00

So i got a Qtec 9100 with broken LCD, with part number - 60H00037-00.
But i found a 60H00032-00. And when i dig in da net i understood that 9100 was manufactured with this two kind of LCD. So i put da LCD on and turn it on. It works but the colors are inverted (like on foto-film). I found also that Cingular version - 8125 is with 60H00032-00 LCD. So i down the RUU for Cing8125 - but it says "Invalid Vendor ID". So how can i convert it to 8125 or i don't kwon just wanna to make the colors on LCD Right. Will be thankful of any solution you provide me with.
You have to CID-unlock your device to get the rom flashed.
BUT:
Most people on this forum have flashed a damn lot of different roms and nobody has got wrong colors on the lcd =)
So, i think this is a hardware issue (depends on a jumper or something like this).

Qtek 9100 going blind

Hi have a qtek 9100 with multiple problems.I cannot reset (hard or soft)each time i try it turns of and i have to take out the battery and back again to make it start.And after a few minutes when the phone is on i cannot receive and make any calls or enter any programm.When i try i see a variety of messages.Please someone HELP.
My QTEK is a G4,OS is 2.17.7.2,WM5.

Align screen

ok i'm stuck on the Align screen after the hard reset of my Qtek 2020i and i searched all the forum thoroughly all i found is the way by using Remote alignment tool, but the problem is i dont have cradle for the phone, and its kinda not availaible in my country and i'm use bluetooth to activesync my device but now as i'm stuck in the align screen i cant activate or deactivate my device bluetooth, and now i'm in a big trouble n i dont wanna lose my device so help me out guys.
ok after many taps i succesfully start the phone but its not aligned properly, i just need a calibration data for Qtek 2020i plz help
http://forum.xda-developers.com/showthread.php?t=290272
should i used this calibration data?
at least tell me is this gonna work with my screen or not?
looks like this should work, qtek 2020i is the same device, just a different name, I can't say for certain if this will work, since it may be a problem with the screen itself, but it's worth a try.

Categories

Resources