Qtek 9100 going blind - 8125, K-JAM, P4300, MDA Vario Software Upgrading

Hi have a qtek 9100 with multiple problems.I cannot reset (hard or soft)each time i try it turns of and i have to take out the battery and back again to make it start.And after a few minutes when the phone is on i cannot receive and make any calls or enter any programm.When i try i see a variety of messages.Please someone HELP.
My QTEK is a G4,OS is 2.17.7.2,WM5.

Related

qtek 2020i ph10c screen will not align after hard reset

Hi i am new to this site so hello peeps...
Anyway i have had my qtek 2020i for about 3 months now and apart from the odd reset (that i have done) its been a useful tool.
Now the other morning it decided to have a freak out and the start menus locked up. I tried to do another reset but nothinge changed..
Now my dilemma is....i performed a hard reset and now the screen will not align...it asks me to tap to set up my device and i start tapping the little crosses but it will not work..i seem to be tapping the crosses for ever with no luck. Can anybody help?
thanks in advance.
Sounds like "Take it back to the shop" time to me.
Something far wrong mate.
Danny-B- said:
Sounds like "Take it back to the shop" time to me.
Something far wrong mate.
Click to expand...
Click to collapse
spot on simple logic i suppose cheers geez
hehe, you could try a rom update or reflash, might be a problem with the rom
I got the new unit it was working fine......then i restored the backup that my last phone took before it went away and guess what....the problem returned :evil: .
Anyway i reflashed the rom with the qtek one and its sorted. :lol:
What is the best rom in your eyes for the alpine device?
The last O2 ROM with Pugs adaption, the 1.3 radio included.
Search for Pug it should come up with a link to his rom.
The newest O2 rom has an older radio version(1.0) because it has Blackberry support (which i will never use)
I am hardly recommend 1.04 radio version. It solved 3 issues for me and made my phone recieve signal better! This is "must have" version of radio!

G4 T-mobile MDA Vario, problems, solution - New ROM maybe???

Hello!
I bought my T-mobile MDA VARIO G4 few months ago and now I have some problems. When I am writing Emails or SMS just suddenly keyboard locks and I am able to write message only with stylus. When this happens also all the keys on the phone freeze and after I push the main key on the front several times I get screen telling me that I have to align screen and I have to follow the mark on the screen with my stylus.
So my Wizard is becoming Magician and I don’t want that, because I bought this device in the first place because of the full keyboard.
I have two explanations for my problems:
a) Problem is in a software and I would like to upgrade the ROM, but I don’t know how or where can I get the latest ROM (as far as I know it has to be from T-mobile, because my phone is CID locked)
b) Problem is in hardware because I had once my MDA in moistures atmosphere. I work in a hotel and I had to inspect Turkish sauna once and my phone was exposed to water steam for about 10 minutes. Problem didn’t started immediately but one day later, so I am assuming that this could also be the cause for all the problems.
I would be very glad if you could help me with your advices.
I apologies for my English, I am not a native speaker.
Can I install this ROM http://www.tm-phonedownloads.com/download_manager_mda_vario.html
on my device, regarding that I have CID locked device??

Big troubles with my QTek 9100...

Hi all,
First of all, I would like to thank the authors (and all people concerned) for this great forum. You're doing a great job !
Then my problem:
Some days ago, I tried to upgrade my QTek because I wanted it in dutch. To do this, I followed the method explained by Risidoro in his thread (http://forum.xda-developers.com/showthread.php?t=271043)
I downloaded the dutch 2.18 ROM from the official MyQTek website.
I've done everything like it was described in the pdf and everything seemed to go well.
The problems came after first restart:
- my QTek was very very slow, e.g. 5 to 10 seconds to expand start menu.
- when I pluggged the USB cable, battery didn't charge and QTek wasn't detected by my computer, so no ActiveSync possible anymore.
Acutally, I've lost the AC charger and now, my battery is completely off.
I really don't know what to do.
If someone has a suggestion for me, he's welcome !
Thanks in advance !
FJ
f.jacobs said:
Hi all,
First of all, I would like to thank the authors (and all people concerned) for this great forum. You're doing a great job !
Then my problem:
Some days ago, I tried to upgrade my QTek because I wanted it in dutch. To do this, I followed the method explained by Risidoro in his thread (http://forum.xda-developers.com/showthread.php?t=271043)
I downloaded the dutch 2.18 ROM from the official MyQTek website.
I've done everything like it was described in the pdf and everything seemed to go well.
The problems came after first restart:
- my QTek was very very slow, e.g. 5 to 10 seconds to expand start menu.
- when I pluggged the USB cable, battery didn't charge and QTek wasn't detected by my computer, so no ActiveSync possible anymore.
Acutally, I've lost the AC charger and now, my battery is completely off.
I really don't know what to do.
If someone has a suggestion for me, he's welcome !
Thanks in advance !
FJ
Click to expand...
Click to collapse
you will either have to buy another battery, use the 9-volt trick detailed in one of the threads in this forum, or have a friend charge it in their phone for you.
After your battery is good again, I would suggest flashing your carriers approved rom to your phone and then following the instructions in the Definative guide to CID Unlocking and Rom Upgrading G3 wizards sticky.(assuming you have a G3) When your device is CID unlocked you will have much better results with trying to flash your device.
My best guess (since you didn't give any information such as IPL, SPL, GSM, or OS versions) is that you mixed a 2.xx OS with 1.xx bootloaders, which puts your phone in a pretty much unusable state, boots but is sluggish and phone does not work, will not charge.
Thank you for your answer !
You probably noticed that I'm a totally newbie in this, that's why I do mistakes.
I was looking the forum for this 9-Volt trick thread, I only find a sentence about 2 wires to connect. Maybe you can give me the direct link ? (or maybe I ask you too much )
And when I'll have my battery full, I'll give you the IPL, SPL. As I remember, it was something like 1.09 or 1.26 ! Sorry, I don't know much more !
Another thing: how to know if my wizard is a G3 or G4 one ?
Thanks again !
FJ
Ok, I found some definitions like CID, IPL, SPL...
Now, I have to charge this .... battery !
FJ
Trick
I found this in french:
http://qtek9100.forumpro.fr/LES-DIF...-f11/TUTO-forcer-la-charge-Batterie-t4154.htm
Here are the steps explained :
1. Find an AC adaptor close to your battery values: for Wizard 3.7v and 1250mA (the author of the post used a laptop adaptor 5.2v and 700mA)
2. Carefully check the positive and negative pole of your adaptor connector (must be available on the adaptor)
3. Connect the adaptor directly to the battery using the first and the last connection
4. Wait 1 hour
5. Put the battery back in the Wizard and use USB cable to finish charge
Still have to test it... I'll keep you informed !
Enjoy !
FJ

HELP: can't flash original rom on G3 wizard.

Facts:
QTEK 9100 IPL/SPL 2.17
After HTC logo it goes to QTEK logo, then fades to white and reboots.
After x number of reboots it sometimes boots Windows WM5. No radio though.
Story is long, sorry.
I wanted to upgrade my phone to WM6 last summer.
Since I was careful not to brick my phone i ordered help from IMEI-Check.co.uk.
I got the code and the software and got busy.. It did'nt work however.
First time it seemed to go fine at first but later it reported to have lost communication with the device. On reboot it would display the problems on line 4 and 5 above. I followed advice and reflashed the device with original rom. Now the device was fine again.
I retried the procedure but got the same problem.
again I tried to reflash original rom but now RUU reported "Invalid Vendor ID"
I sent the device to repair but got it back in the same condition I sent it. "Moisture damage". I opened the device but found very litte evidence of moisture damage.
The device have been sitting in a box ever since, I bought a TYTN, but now I would like to see if there is really nothing I can do to bring my Wizard back to life.
Any good advice will be very appreciated.
Regards
/m
Since warranty is void and you already opened the phone i suggest you get an old tooth brush and some alcohol and give a good 'sponge bath' to it just in case there's some short circuit happening in a hidden place. Be sure to have it well dried before inserting the battery (leave unassembled for some hours or use a hair dryer from a large distance)
After that get phone in bootloader mode and write a 1.xx ROM to it to attempt CID unlocking via free procedures.
If that goes well just upgrade to a 2.xx ROM (with IPL/SPL) and then to WM6
good luck
I will try it
but can there really be a short circuit if the device has been in a box for 6+ months? I suppose it's possible.. I'll let you know.

Align screen

ok i'm stuck on the Align screen after the hard reset of my Qtek 2020i and i searched all the forum thoroughly all i found is the way by using Remote alignment tool, but the problem is i dont have cradle for the phone, and its kinda not availaible in my country and i'm use bluetooth to activesync my device but now as i'm stuck in the align screen i cant activate or deactivate my device bluetooth, and now i'm in a big trouble n i dont wanna lose my device so help me out guys.
ok after many taps i succesfully start the phone but its not aligned properly, i just need a calibration data for Qtek 2020i plz help
http://forum.xda-developers.com/showthread.php?t=290272
should i used this calibration data?
at least tell me is this gonna work with my screen or not?
looks like this should work, qtek 2020i is the same device, just a different name, I can't say for certain if this will work, since it may be a problem with the screen itself, but it's worth a try.

Categories

Resources