Related
Alright my At&t tilt front face buttons started to not work (i could only use the arrow buttons and the ok button) and my keyboard stopped working but the arrow keys would. i upgraded the rom after calling htc for help. that didnt fix a thing and now today none of the buttons work. i keep getting the PTT to come up and ask for installation and edfc keeps typing themselves on the screen. so idk if it is a software problem or if the hard ware is malfunctioning.
Damn, I got the same problem. Does anybody know how to fix this?
the same problem here... :/
same problema here.
i already tried another radio, another SPL, another ROM and nothing.
any idea?
Just updating.
Yesterday my tytn started working perfectly again, but today the same problem is occuring. I did nothing, so probably is really a hardware issue.
I have a similar problem.
Send/End + Soft Keys + Keyboard are not working. The issue is not resolved yet?
Wow, this problem just happened to me as well. I've searched everywhere on the net and couldn't find anything.
So is this a pervasive issue? Anyone with any hint as to what might be the source of the problem?
Originally, I thought it the PTT button was stuck in the PRESSED position because the phone behaves as if this button was constantly being pressed. For example my PTT button was mapped to Voice Recorder if the PTT button was held down. The voice recorder constantly comes on everytime I turn the phone on!!
1234567890
I have the exact same problem.
The only change I recently made (two weeks ago) was installing tom tom navigator.
First I thought it was a virus and I installed bull guard, but with no success.
It opens/closes the start menu every second, no buttons work apart from the directional buttons and it writes "edfc" in my textmessages when I turn on/off the screen with the power button.
Most of the time(!) this irritating opening/closing of the start menu only happens after I first turn off/on the screen (with the power button).
I saw this problem described in a post dating back almost two years ago. Someone ought to know the answer to our problems. What does HTC say about it?
I have been lucky and not had this issue yet; but I would recommend starting by flashing the stock rom from HTC. Then hard reset; that will clear everything back to original. If you still experence this after that, then you have a hardware issue. Good luck
This just happened to me this morning. I cant use any buttons and nothing is popping up. This is soo wierd cause the phone was just sitting there overnight!!
Me too...
I have been going nuts with this issue for a couple months now. Makes the phone unusable half the time. I am so disappointed to find that a ROM reload doesn't fix it!! I remapped the 6 key to none and that sort of helps but it was mapped to Voice record before and it would constantly record memos until all the memory was gone in the phone and then it would all crash from there. So frustrating.
I too get the edfc message after I reboot....
It really seems like a virus the way it acts but I guess if it is a hardware issue then it's not a virus.
Anyone ever figure anything out with this? Nothing has changed on my phone recently.
Still an issue?
Holy Toledo fellow Tilt Users. Have you ditched your half-functioning touchscreen, or have we figured out how to solve this issue.
Recently I FOUND THE SAME PROBLEM!
I am going to do what was suggested (original HTC Rom & hard reset) and will let you know if I get the rest of my keyboard back...
All buttons except for power and... NOT WORKING
Outside "Enter" buttons work but they are mapped to Windows key. ? Weird. For some reason the kaiser thinks it is something else. I do not know how it got this way, but there must be a way to convince the hardware of the existence of all my other buttons. The entire keyboard does not work.
Hard Reset & stock HTC Rom did not help. I was surprised that I could hard reset it at all since the two soft buttons are unresponsive to software.
Anyone figure this out yet?
Hi, I got the same issue today as well - Has anyone got rid of this?
(Sorry - this was previously in the wrong thread category)
Hi,
after installing some software apps (numerous freeware utilities), my diamond does not ring anymore when I am called (it does vibrate).
I have checked everything but cant switch the darn ringing on again - other sonds work fine, it just doesn't ring. This is the second time this has happend - after the first time the hard-reset fixed the problem, but then I reinstalled several programs again and the same problem is back again.
Does anyone have any ideas what I can do about this without doing a hard reset?
Perhaps there is a Tweak utility where I can see if the ringing has been switched off?
Please help.
Thanks in advance - I would really appreciate any suggestions.
Berx1 said:
(Sorry - this was previously in the wrong thread category)
Hi,
after installing some software apps (numerous freeware utilities), my diamond does not ring anymore when I am called (it does vibrate).
I have checked everything but cant switch the darn ringing on again - other sonds work fine, it just doesn't ring. This is the second time this has happend - after the first time the hard-reset fixed the problem, but then I reinstalled several programs again and the same problem is back again.
Does anyone have any ideas what I can do about this without doing a hard reset?
Perhaps there is a Tweak utility where I can see if the ringing has been switched off?
Please help.
Thanks in advance - I would really appreciate any suggestions.
Click to expand...
Click to collapse
didi you installed pointUI and the SystemInternalsV2????
you might not like the answer, but hard reset has fixed that problem for me with the diamond and 2 other htc phones i had in the past.
adempozhari said:
did you install pointUI and the SystemInternalsV2????
Click to expand...
Click to collapse
What is pointUI ? - I have the standard diamond branded user interface from O2 with all the system internals and the ROM version 1.93.207.2 German.
Please help me - I really do not want to do a hard reset because the last time I could not retrieve my back up with the Sprite backup utility .
Thanks in advance for any help.
i can't believe i'm now posting in this. i remember telling you to post this on the main diamond forum and now i'm having the same problem.
i've tried putting the ringtones in the internal storage, and on the phone's main memory, sometimes i hear the ring for a split second before it goes silent.
from searching, it seemed like some people have had this issue with some SRS WOW program but I don't have that.
have you been able to resolve this? I too would like to avoid a hard reset if at all possible, i just got the phone setup the way i want it and it would take a ton of time to get it back....
This may sound stupid, but give it a try, it has helped before...
Go to the settings tab in TF3D.
Tap Sound
Set Volume at 100%
Sometimes, the ring volume gets reset to 0 by itself, and it took me 4 weeks before I found it, after trying about everything, from uninstalling every app to hacking the registry.
Twabi2 said:
This may sound stupid, but give it a try, it has helped before...
Go to the settings tab in TF3D.
Tap Sound
Set Volume at 100%
Sometimes, the ring volume gets reset to 0 by itself, and it took me 4 weeks before I found it, after trying about everything, from uninstalling every app to hacking the registry.
Click to expand...
Click to collapse
that's usually one of the first places i check... i'll keep it in mind though.
i think i might have an idea what my issue might be, so it was working this morning but i noticed microsoft's voice command was announcing the name of the caller as it was ringing. so i think it might be an issue with the msvc. i'm going to try disabling the voice announce and see what that does...
Problem Solved!
Hi,
guess what - I finally found the solution
I never bothered to read the Diamond manual as I believed the user friendly interface to be self-explanitory - however, I overlooked something very important!
When setting the volume up or down by means of the buttons on the left hand side of the Diamond, the usual vertical bargraph type of display appears and reacts according to how the adjutment is made with the volume up or down buttons, this is clear. There is also the possibility to mute the phone or to put it into vibration-only mode.
Now, at the top left hand side, there is an arrow (looks like this: <). If you quickly tap on that with the stylus before the screen goes away again, you will get a new screen for another setting - now this setting is for adjusting the ringing volume / mute / vibration settings (now the arrow is on the top right and looks like this: >
It is so simply expained: The system volume is not the same as the telephone ringing volume and just requires the quick click on the top left hand side of the screen and voila, bob is your uncle! You can then set the ringing volume up and your phone will ring again.
I wantend to know why the heck the ringing volume just changes or what caused the problem and I have also been able to determine why the ringing volume settings change - to explain:
When setting the SYSTEM VOLUME to mute - then the PHONE RINGING VOLUME is also muted! However, when then setting the system volume up again, the ringing volume still remains muted! This is important to know and it can also happen accidentally or it may be forgotten to reset the ringing volume. I dare to say that this was not really thought about very well and I hope the developers will change this or show a VOLUME STATUS for both the SYSTEM and RINGING volumes somewhere on the desktop/today screen.
... or would that not be a good project for a developer here on this forum perhaps? I would appreciate a comment here...
Thanks anyway for the kind responses and willingness for your help.
I have to date still not read the actual over 260 page little manual booklet, but it probably is described in there. Moral of the story: RYFM (for those who know what that stands for)
Amendment: Found it described on page 42 in the manual booklet - it's actually described there but can be easily overlooked and it is not described that the system volume settings affect the ringing volume settings.
Ok, so the phone rings now but I have a similar problem with my GPS receiver
I will open another thread for this - hopefully someone can help me.
Best regards,
Mike - Germany.
I had the same problem.
It happened to me.
All the system sounds were fine, but the ring wasn't there.
Checked settings, change ringtone, tried a lot of stuff.
I was begginning to think about a hard reset when I found my problem origin:
At least in the ROM that I use (Shaks), when you press one of the volume keys in the side of the phone, you change system and ring volume.
If I press it all down, it goes to zero then vibrate then silent, and normally the system and ringer volumes are equal when you do this.
In that system volume screen that appears when you press volume key, there is a arrow in the top left. If you press it, you'll go "ringer volume" screen. I noticed that system volume was in maximum but the ringer volume didn't fallow it.
That said, if your ROM uses the volume keys in that same way, press that arrow and check if the ringer volume is on too.
Hello Guys, (love this forum)
I have the HTC PRO and I'm getting depressed because the volume buttons alway (somehow) turn down the volume of the ringtone. I miss calls more then ever.
I searched this forum but couldn't find any answers to this.
I did found one solution for the HD. Change something in the Register (defaultpage from 1 to 0) Didn't on my Pro aswell on the HD of my friend.
Anyone else got a clue to switch this buttonoption off. Tho I need the buttons for the systemvolume. Maybe somebody knows how to get rid of the ringpage completly and just leaving the systempage working.
MANY THANKS to Anybody that can help..!
(if I did anything wrong on this forum or upset anyone - sorry, I am a newbe)
Greetings,
MDK
I can honestly only advise 1 thing, and that is that you install S2U2 which is a free soft that locks your phone and the buttons as well,
I've got another option which is changing the volumecontrol.dll but afterwards all your apps will minimize every time you open the keyboard = flip the screen... And this is even more annoying when you want to reply to an sms...
I had the same problem but S2U2 is the best option
Another vote for S2U2
But, if you have updated to the "leaked" 6.1 update (at&t rom), it might cause you a headache, at least it did with me. When the phone would announce an incoming call, s2u2 & the new built in slide to answer will fight each other.
Wait, I think you mean that when you put the system volume down, the ring volume goes down...right. You can put the system volume down and tap the Ring tab and put that volume up.
Hi all, please can you help me with this!?
Firstly when my phone boots or is taken out of sleep mode it immediately activates voice record as if this button has been pressed. It then opens the dialler and types ‘EDFC’. If I open pocket word and then wake the phone up it also types ‘EDFC’ before doing the above.
My keyboard is not working and the only hardware buttons that function are the power button (only for a while), the camera button and the silver select button in the middle of the d-pad. The jog wheel and silver directional d-pad buttons occasionally come to life. The others don’t work (green call and red end buttons, ok, windows etc).
When I use the standard keyboard SIP on the screen the directional buttons and delete do not function?!
I’ve reverted to a stock ROM to make sure this isn’t the problem.
It appears as though my Kaiser thinks these buttons are being depressed, but I’ve checked them and they click normally and release when pressed (even though they don’t perform a function) so nothing is stuck down etc….
I’m going to use AE Buttons to try and unhinge the button functions for now, but it would be great if someone has any suggestions!!
Thanks in advance.
Update - AE Button won't unhinge the buttons or change their function to anything else (e.g. nothing). I can't stop this from happening every time the phone boots/wakes up!
Help!
Mine got the same symptoms last week except it opens quick something or other,and then the dialler dials 2547.The screen for my pin then comes up,which I can enter normally.Home screen fires up normally but the keyboard will not work or any buttons except the silver one in the middle.Searched a bit and this problem is very common although I cannot find a solution anywhere.Can someone please help
AE button didn't work?
When mine did that, I reset all the hardware buttons (not the keyboard, just the buttons reachable from the outside. A soft reset and viola!
That's the only solution I have. It's worked for me 2x.
Also try pulling the battery for 20 seconds or so and restarting. That has fixed my touchscreen not working after it gets spashed 3x. Yeah, my phone is old and abused, but keeps working.
Will
wasilvers said:
"I reset all the hardware buttons (not the keyboard, just the buttons reachable from the outside. A soft reset and viola!"
Click to expand...
Click to collapse
Thanks for your replies - I've got Orange sending me another one in the morning now and sods law it's just stopped happening.... Taking the replacement anyway in case it happens again.
For my knowledge, how did you reset the buttons? I deleted some registry keys to completely stop them working (although I couldn't find the registry keys for the red and green buttons).
Searching on Google there are quite a few reports of this, but no one has ever posted the cause!
I am having the same problem... please help. My phone is going crazy. I did a hard reset but still didnt solve the problem....
I am also having this issue. Phone starts typing EDFC and then initiates the voice recorder. I reflashed various ROMs and regardless of what was flashed.. initially they appeared okay, then it started happening again. I also tried hard and soft resets. Nothng has worked so far.
I resorted to disabling the keys and some of the applications which I dont use which appear to be getting started/run (Voice recorder for one). So far I havent had the issue, knock on wood.
I think this is more than likely a hardware error. My tilt is actually pretty old so I wouldnt be surprised. If someone finds either the cause or a workable solution please post. Im trying to hold off until January when my contact expires to get a new HTC.
I searched and searched but found no solution for this and ended up getting the phone replaced.
HTC seemed to know nothing of such a problem....
Have you tried whacking it?!!?
Hope you get it sorted.
brandall said:
Have you tried whacking it?!!?....
Click to expand...
Click to collapse
Hmm, yes, but I don't see how that helped my phone.
lol, all jokes aside, my friends, I ask in this thread as well,
what is causing this problem? I ran into this issue after ALL my buttons stopped working (except for the power).
I installed a new rom (I forget which one), and still nothing works except for power button.
It would be even better if someone knows the solution!
-Calling for Help-I'm still convinced it is a software/registry problem...
Okay, so there's no solution available for this weird problem of ours.
On the bright side, however, it is amazing that we can still use the phone, even after it requires servicing (some way or another). I have accepted this handicap that has been placed on my phone for now, simply hoping it will grow out of it one day.
But something isn't right. When I looked in the registry (trying to follow some directions I found within the wiki for when your keyboard STILL doesn't work properly), there was a discrepancy between what was supposed to be found in the registry and what was actually there. It wasn't that the values were wrong, it was the names of the values that were different. Why could this be?
Or even if you have moment of time, and you have an AT&T Tilt, and it works perfectly, maybe you could write up a run down of what you have hanging around in that section of the registry?
Hey, just so I can be sure, is there some place I can cross check what I have in my HKEY_LOCAL_MACHINE\HARDWARE\DEVICEMAP with what is supposed to be there in a fully functioning AT&T Tilt?
Dear PDA experts, please help me!!
since a couple of days I am having a VERY annoying problem with my HTC Diamond. This occurs when I am using the original hands-free. It looks like the cable is losing contact or making an incorrect contact...
So, when using the hands-free, the phone starts dialing the last dialed number by itself. When I am listening to music, the music stops and I am hearing how the phone is dialing. This usually happens, when I make the move to put my phone in my pocket. Also, when I speak with someone, the phone automatically puts him on hold, which is even more annoying for the other party! The problem persists even when I switch off the phone module, it still tries dialing!
I had tried many times to get rid of the voice dialer (sddialer.exe), but I cannot delete or rename the file even when I connect the Diamond to a PC. Finally I have disabled it from the registry and it still starts dialing when I make the move to stick it into my pocket!
And I dont have the impression, that the cable is somehow defective, as when I am listening to music, it does not break up. And it always does, when there is a problem with the cable, unfortunately I have a lot of experience with defective hand-frees. Please please help me!! It is not worthy to buy a new handsfree for such an old phone... Is there a way to disable all the buttons of the hands-free, it is the last possible solution I can think of...?
Use the lock screens
My Diamond did that too.
There are several lock screen capabilities that you can enable under settings. More important if you added a custom Rom they usually have a few different options.
With the custom Rom I was running, I could make a call and after pushing the power button, it would lock the phone when on the line with someone. This would happen if you hit any button after the power button was pressed (which usually turns off the screen).
Hope that helps.