Database Develop

Helpme Please My HTC Kais130 (AT&T Tilt) NO RUN , IS DEAD

Helpme Please My HTC Kais130 (AT&T Tilt) NO RUN , IS DEAD, only power on and ( smart mobility in display black) and no more
helpme please

Hello there, we all understand youre frustration. But for beeing able to assist you everyone need to know what exactly happend here? Where you flashing? Did it fell out of youre pocket? What where you doing last on it and so on. Take 5 minutts or more and provide as much info you can then edit youre post. That is AFTER you have searched and digged trought this board using google aswell for keywords on youre issue.

didnt flash, it was working well suddenly is dead, plug in cable usb,and is the same but on screen appear "smart mobility" vibe and then off

hanster said:
didnt flash, it was working well suddenly is dead, plug in cable usb,and is the same but on screen appear "smart mobility" vibe and then off
Click to expand...
Click to collapse
did u try hard reset?

No , i didnt do it, i dont kwon how to do it?

hanster said:
didnt flash, it was working well suddenly is dead, plug in cable usb,and is the same but on screen appear "smart mobility" vibe and then off
Click to expand...
Click to collapse
I know this is a abiouse question but I have to ask, mate.. You are not running flat on batteries? If you havent flashed youre device, and it wount boot and you got power on it you should check youre waranty on the device. Try to charge it for 10 minuts or so (check that you have charging light on) then try to start it again.
I understand you correctly that you havent HardSPL youre device at all or?

hanster said:
No , i didnt do it, i dont kwon how to do it?
Click to expand...
Click to collapse
u should do a hard reset.
Here is a step by step for u:
http://wiki.xda-developers.com/index.php?pagename=Kaiser_Resets
Remember after performing a hardreset, u will loose all your data on your phome(not on SDcard).

Kaiser_Resets
Back to Kaiser Wiki
--------------------------------------------------------------------------------
Soft Reset
Using a stylus, press the soft reset button at the bottom of the phone
Hard Reset **NB** This cannot be performed while the device is connected/charging!**
Press and hold both soft keys
Using a stylus, press and hold the soft reset button at the bottom of the phone
Keep all three buttons pressed until the keypad lights turn off and then flash
Release the soft reset button while still pressing the soft keys
Let go of the two soft keys once the message "This operation will delete all your personal data, to manufacturer default" appears on screen
Finally, press the green call button to perform the hard reset, or press other key to cancel
Bootloader
Press and hold the Camera button
Using a stylus, press and hold the soft reset button at the bottom of the phone
Release both buttons once the bootloader screen appears

did u do it?

this is my phone
this is my phone where is it the soft key
Press and hold both soft keys

I have currently disabled pics so I cant see the pics of your phone.DOnt u have kaiser?

The soft buttons are the ones next to gren and red phone buttons and above messaging and internet buttons.

im doiin that but dont do anything, dont show a message for reset phone what more can i do, can i repair with any software, any test mode , any flash

hanster said:
im doiin that but dont do anything, dont show a message for reset phone what more can i do, can i repair with any software, any test mode , any flash
Click to expand...
Click to collapse
just be sure u are doing the hardreset right. Some guys had problems, cause they had big fonger and they were pushing not just the soft buttons but also a buttons that are around them.
Hold these two soft buttons, then stick the stylus to the hole and hold it there antil a white screen appears where is the message shown. Then push the green phine button.

http://www.mediafire.com/?rc3vbcqdtbh
here you go a video

http://www.mediafire.com/?lrgmtzy4mat
here you go a video of problem the my HTC

hanster said:
http://www.mediafire.com/?lrgmtzy4mat
here you go a video of problem the my HTC
Click to expand...
Click to collapse
Ok, I have seen the videos. Did u try the reset with the kaiser closed?
I remember a thread with similar problem, will try o find it and post back.
PS: In the first video, u have three hands!!

OK, I found this one:
http://forum.xda-developers.com/showthread.php?t=374388&page=3
Similar problem, does your kaiser reboot continuosly or the screen just flashes.
Your best bet is to read the whole thread, try to learn something about mtty and contact gsleon.

Bizarre boot up problem after upgrade to wm6.1

I've strange problem with my BA after upgrade to wm6.1 (no matter which ROM version, all behave in the same way, no matter which radio version either). I have to switch on BA twice before RADIO shows up. That's mean if I switch it on, only by button on the top, there will be no radio. It's shows up after soft reset. For clarification, my switch on procedure looks like this:
1. button on top
2. color stripes shows up (no radio)
3. soft reset
4. color stripes, radio is on
After roll back to WM2003se everything backs to normal.
Is there any possible way to have normal boot up after upgrade?
Best regards,
Mar.S

as found in many other entries here in the forum and in the wiki, this bug/problem has been there on every rom, every build since wm5. it is not bizarre at all. we all have that. takig out the battery is not a legit way to soft reset your device. and i believe "switch on" is not the right term, because if you press the power button on top, it should wake up from stand by.
so, if you are talking about the soft reset behaviour, it is perfectly normal, that the device acts this way.
Chef_Tony

all you have to do to solve it is every time you switch on from a "cool boot" (as in turning on from a point of having taken the battery out) is press the soft reset button.
easy
josh.
this happens on my blue angel with wm6

Diamond freezes upon startup - No Sync Connection

Hi there,
i recently flashed this Rom: /ROM\WM6.5|23017&23060|Benko's 4.9ROM's|NEW| Full, Prime&Clean[Manila2.1 R1.5/16.10]
and everything was working fine. Then i installed some program (SPB Diary). And since then my Diamond keeps on freezing up upon startup. It shows the Notifications Windows (Network provider, Battery status, "No new notifications" and the "close" button at the bottom).
But then he wont react to anything. He doesnt establish a connection to my computer, so i cant flash a new rom on my device either.
Im totally lost, can someone help me?
Che

che27 said:
Hi there,
i recently flashed this Rom: /ROM\WM6.5|23017&23060|Benko's 4.9ROM's|NEW| Full, Prime&Clean[Manila2.1 R1.5/16.10]
and everything was working fine. Then i installed some program (SPB Diary). And since then my Diamond keeps on freezing up upon startup. It shows the Notifications Windows (Network provider, Battery status, "No new notifications" and the "close" button at the bottom).
But then he wont react to anything. He doesnt establish a connection to my computer, so i cant flash a new rom on my device either.
Im totally lost, can someone help me?
Che
Click to expand...
Click to collapse
you will have to hard reset, when u switch ur diamond on, hold volume down, the big round button and hit the red reset button under the stylus, do this while windows is booting b4 it freezes..... i had a simlar problem with spb mobile shell ageees ago lol

I tried then, then i see the 3 colored screen, then it says "No Image File" on a grey screen, then it says "trigger usb host" and "retry entry usb" (does the a few times), then it goes back to the 3 colored screen after a while of waiting, and it says "USB" in the center.
But thats it, problem still there
Any idea?

no if that appears your holding the back button not the round centre button

Thank you so much for your help, i though hard reset was hard reset either way, didnt know that there was a difference between which of the buttons (back, hang up, center) to press.
My Diamond is up an running again, Thanks for the help!
BTW: What exactly are the different modes of hard resetting for? Is there a manual somewhere?

che27 said:
Thank you so much for your help, i though hard reset was hard reset either way, didnt know that there was a difference between which of the buttons (back, hang up, center) to press.
My Diamond is up an running again, Thanks for the help!
BTW: What exactly are the different modes of hard resetting for? Is there a manual somewhere?
Click to expand...
Click to collapse
The method you described is for flashing a rom from your internal storage... Next time you download a rom, take the .nbh file and change its name to DIAMIMG.nbh, Then copy it to the root of the internal storage, if you then hold vol down, the back button and press the red reset button, you can flash the rom without using a ruu, this way is also alot faster then the old method

[Q] Need Help, My Diamond doesn't boot properly

Hi, I'm new to XDA Dveloper. sorry if its already questioned..I don't have time to search for them, I'm running my laptop on battery that only will last about 15 minutes..and I have my electricity out..
Yesterday, I got My diamond exposed to water...it was raining hard and I was on my bike with my diamond in my pocket..
when I got home, my diamond begin to act strangely, it keeps lower its volume(to vibrate state) when I try to press the increase volume rocker, it goes back down to vibrate. but I manage to shut it down with slide2shutdown...and charge it (the battery only 7% left). this morning I get up and switch on the diamond, but It doesn't boot like usual(theTOUCHDiamond sceen)...
it only shows 4 bars (RED, GREEN, BLUE, and WHITE)consist of:
RED BAR with this:
DIAM100 64M
SPL-1.37.Olinex
MicroP-Diam (LED) v11
GREEN Bar with:
PSOC-Diam Stage_PVT v0x30
BLUE Bar : blank
WHITE Bar with
Serial (only "serial is written, nothing more)
That all, and when I try to connect with USB cable, it demands Qualcomm CDMA Drivers...(I use My friend's laptop....no activesync installed)
anyhelp would be appreciated.
thanks

Its strange..., Now my phone could boot normally, but the volume control still error..it keep decreasing( i tried to increase it but it keep getting back to 'vibrate' is this becaus the water?
EDIT: I'm sorry...its still the same, if I restart the device..it shows the 4 colored bars screen again. when I try to reset it, 1 of 10 attempts is likely that diamond boot normally..but the volume error is still there...can sum1 help me?
PS: Sorry, I don't know that I could edit my post..

bellsprout said:
Its strange..., Now my phone could boot normally, but the volume control still error..it keep decreasing( i tried to increase it but it keep getting back to 'vibrate' is this becaus the water?
EDIT: I'm sorry...its still the same, if I restart the device..it shows the 4 colored bars screen again. when I try to reset it, 1 of 10 attempts is likely that diamond boot normally..but the volume error is still there...can sum1 help me?
PS: Sorry, I don't know that I could edit my post..
Click to expand...
Click to collapse
what are you trying to hardreset device..??
A hard reset should only be performed if a normal reset does not solve a system
problem. After a hard reset, the device is restored to its default settings—
the way it was when you first purchased it and turned it on. Any programs you installed, data you entered, and settings you customized on your device will be lost. Only Windows Mobile® software and other pre-installed programs will remain.

Try flashing back to stock rom?
Sent from my GT-P1000 using XDA App

Hi!
I have a boot problem also.
I used Memo ROM about 1 month ago. That was worked well still today. I restarted my Diamond today, it was not boot correctly. Only reboot the phone after showing the ROM information. I made hard reset and put back the rom again, but the phone is not boot properly.
Could to help somebody for me?

I solved the problem.
I downloaded the original rom (included with radio rom) from htc.com.
I put the phone to bootloader mode and flashed this original ROM.
After flashing finished, my diamond boot to WM6.1.
I don't know what was the problem, but it works again...
I hope never happening this again!

i bricked my x1

i tried to upgrade the rom from WM6.1 to dynamics 2.0
i did everything and update successfully.
x1 reboot and went into start up screen saying hard reset on first run,
i tried to hard reset but my "R" dont seems to be working..
so i pressed "space bar" to restart.
after that it cant start up, i tried to hard reset, soft reset, take out battery, nothing seem to work, only a pulse of vibratiion... the screeen remains totally blank.
is my x1 dead?
thanks for the help

B3nGz said:
i tried to upgrade the rom from WM6.1 to dynamics 2.0
i did everything and update successfully.
x1 reboot and went into start up screen saying hard reset on first run,
i tried to hard reset but my "R" dont seems to be working..
so i pressed "space bar" to restart.
after that it cant start up, i tried to hard reset, soft reset, take out battery, nothing seem to work, only a pulse of vibratiion... the screeen remains totally blank.
is my x1 dead?
thanks for the help
Click to expand...
Click to collapse
try to flash that rom again

try to hold two silver keys and push the power button till you see tricoloured screen or try pushing two silver keys and soft reset button with stylus which is located in a tiny hole just stylus sized on the back right side of the phone

i tried 2 silver buttone with the power button and the back hole.
but my screen still remain blanked.
totally nothing.. only a pulse of vibration.
is it possible to be in this stage? will a totally bricked x1 still able to get tri color?

i think u should charge your battery. and then put a kovsimg.nbh file on sd card.
after that install the rom by pressing the volume button down and power button.

px1ilanmy said:
i think u should charge your battery. and then put a kovsimg.nbh file on sd card.
after that install the rom by pressing the volume button down and power button.
Click to expand...
Click to collapse
hi,
i have tried charging the phone,
i tried pressing 2 silver buttons and power button
i tried pressing 2 silver button and stylus poke reset hole for 5 sec
i tried power button with volume down..
nothing works.. its just give a pulse of vibration and a black lighted up screen, nothing else.
anyone please help. =(

you know those leds on the sides of the phone try charging the phone and see if they glow if they do then your screen may be broken or your flex cable has worn off i'll put my money on the flex cable if so then you should order a new one and replace it or take it to a service centre

Info about the way you've got to the trouble looks little... not clear.
i tried to hard reset but my "R" dont seems to be working..
so i pressed "space bar" to restart.
Click to expand...
Click to collapse
How did you press space bar if "R" doesn't work?
Then... If you can get into bootloader mode, you can reflash any rom you like... you have hard-spl installed, have you?
You can use few different combinations to get into bootloader -"power"+"vol-down" OR "power"+"cam button". As you have vibration on the start, I assume your bootloader isn't broken, so you should be able to do these operations.
Charging should work as well, even if you don't see any sign of charging.

bruno_123 said:
you know those leds on the sides of the phone try charging the phone and see if they glow if they do then your screen may be broken or your flex cable has worn off i'll put my money on the flex cable if so then you should order a new one and replace it or take it to a service centre
Click to expand...
Click to collapse
Yeah i can charge,
Led at the side does glow, when i call it will blink and vibrate, but i cant pick up, no buttons is working on the front screen, dont know about th qwerty..
i guess flex is crappy.. but if flex is crappy, the screen will light up but remain blank? the led will glow?

ultrashot said:
Info about the way you've got to the trouble looks little... not clear.
How did you press space bar if "R" doesn't work?
Then... If you can get into bootloader mode, you can reflash any rom you like... you have hard-spl installed, have you?
You can use few different combinations to get into bootloader -"power"+"vol-down" OR "power"+"cam button". As you have vibration on the start, I assume your bootloader isn't broken, so you should be able to do these operations.
Charging should work as well, even if you don't see any sign of charging.
Click to expand...
Click to collapse
thanks for the advise. i will try again! and report in again..
thanks alot bro!

B3nGz said:
i guess flex is crappy.. but if flex is crappy, the screen will light up but remain blank? the led will glow?
Click to expand...
Click to collapse
if you don't see SE logo on the start and backlight is turned on, if you don't see bootloader tricolor... looks really like it is flex (double check - I am not so advanced in hardware repairing).
Yes, leds should glow in that case.

ultrashot said:
Info about the way you've got to the trouble looks little... not clear.
How did you press space bar if "R" doesn't work?
Then... If you can get into bootloader mode, you can reflash any rom you like... you have hard-spl installed, have you?
You can use few different combinations to get into bootloader -"power"+"vol-down" OR "power"+"cam button". As you have vibration on the start, I assume your bootloader isn't broken, so you should be able to do these operations.
Charging should work as well, even if you don't see any sign of charging.
Click to expand...
Click to collapse
Hi the x1 is able to start up already.
surprisingly, for its blank screen, im able to connect and sync on windows centre and load up hardspl.
after that i follow ur instruction on power+camera, it started showing tricolor and rom flash.
thanks for all the help guys.
THANKS!

my bad , sorry for wrong info