GPRS Internet Explorer t-mobile uk settings connection - 8125, K-JAM, P4300, MDA Vario Software Upgrading

1
Find "Advanced"
Press Start.
Press Settings.
Press the Connections tab.
Press Connections.
Press the Advanced tab.
2
Create new connection settings for WAP and Internet
Press Select Networks.
Press New... below Programs that automatically connect to the Internet should connect using.
3
Enter name
Press the Enter a name for these settings input field and key in T-Mobile GPRS
Press ok.
4
Edit settings
Press the Programs that automatically connect to the Internet should connect using drop down list.
Press the connection settings you have just set up (T-Mobile GPRS).
Press Edit... below Programs that automatically connect to the Internet should connect using.
5
Create new data connection
Press New....
Key in T-Mobile GPRS
Information
If you want to establish a GPRS dial-up connection via another PDA or phone with a modem, you need to select the Generic IrDA connection type.
6
Select connection type
Press the Select a modem drop down list.
Press Cellular Line (GPRS).
Press Next.
Information
The APN name general.t-mobile.uk must be in lower case letters.
If you selected the connection type Generic IrDA in step 6, you are now asked to key in a dial-up number. Key in *99# and go to step 8.
7
Enter APN name
Press the Access point name input field and key in general.t-mobile.uk
Press Next.
8
Enter username
Press the User name input field and key in user
9
Enter password
Press the Password input field and key in one2one
10
Delete domain name
Press the Domain input field and make sure the field is empty.
Information
You do not need to edit the settings in Advanced....
11
Save settings
Press Finish to save the settings and return to the list of data connections.
12
Activate the data connection
Press the data connection you have just created (T-Mobile GPRS) to mark it.
Press OK to activate the data connection.
13
Exit
Press OK twice to exit the menu item.
Press Close to return to stand-by mode.

also found these settings
T-Mobile
GPRS Settings (WAP)
Profile / Connection Name T-mobile GPRS
Data Bearer GPRS
Access Point Name (APN) general.t-mobile.uk
Username user
Password wap
Authentication type Normal
Gateway IP address 149.254.1.10
Homepage http://wap.t-mobile.co.uk/
Connection Security Off
Session Mode Permanent / Continuous
Port Number 9201

BUT REMEMBER t-mobile has to have enabled your SIM card to engage in GPRS. Check with them as this is not an automatic default.

Related

GPRS Setup for O2 Ireland

Hi there,
I have the Qtek 9090 with an O2 pay as you go sim. O2 said that the sim card should work.
Go to Start > Settings > Connections Tab > Add a new modem connection.
Enter the following settings:
Enter a name for the connection: o2 gprs web
Select a modem: Cellular line (GPRS)
Press Next button
Access point name: internet (contract) / pp.internet (speakeasy) *
Press Next button
Username: gprs
Password: gprs
Domain: leave blank
Press Advanced button, leave first page as is. Press the Servers tab, tick the option "Use specific server address" and enter the following:
DNS: 62.40.32.33
Alt DNS: 62.40.32.34
WINS: leave blank
Alts WINS: leave blank
Press Ok then Finish
still get the following Error message:
cannot connect for unknown reason. to check your connection settings and change them if needed, tap settings.........if problem continues reset your devive according to manufacture documentation.
Please help! Thanks

Help with Internet Connection

Hi all,
i have had my Alpine opened from o2 and its now on Tmobile. I am trying to connect to the net via wap or gprs yet it tries to connect then tells me the following
The answering modem has disconnected. To check your connection settings and chenge them if needed, tap settings.
Ive no idea what im doing
Any help in plain English please.
Thank You so much
Hi Cheryl, XDA-IIi (Alpine) is an O2 device and the default setting for everything would be on O2 network, if you are using T-Mobile on that then you need to create the settings of GPRS & Wap from T-mobile, I have attached the CAB file for UK-T-mobile just put in your device and run, but try to delete the previous connection settings of O2 if you haven't got any plans to use them in the future.
By the way have you solved your TomTom hanging/stucking problem yet?
http://forum.xda-developers.com/showthread.php?t=286020
GoodLuck
Sidd
Thank you Sid
Sid
You are so helpfull, thank you for your help.
One last question and i will stop bothering you. I have followed your screen prompts and deleted all connections, where to i place the new tmobile file, memorycard or in another file
Once again thank you
Cheryl
Just put anywhere on the device and click to run, once it finish installing it will dissappear itself.
GoodLuck
Sidd
im thick i know
Sorry Sid,
Maybe im too thick to own one of these, its attack of the blonde i think.
I sent the file to my XDA and put it in My Documents, i then came to open it and got the following
"The file \My Documents\UK_T-Mobile.CAB is not a valid windows CE Setup file"
Any ideas
Sorry to be a pain
Cheryl
T-Mobile GPRS setup
This is how I setup my US t-mobile GPRS connection on my device.
- Start Menu/Settings/Connections Tab/Connections icon.
- Select Add a new modem connection.
- Enter the name (e.g tmobile)
- Select "cellular Line (GPRS) as modem
- Click on next and enter "wap.voicestream.com" for access point name.
- Click on next and leave username/password/domain blank.
- Click on finish. (The advanced setting should be set to user server-assign IP and DNS.
Good lucks.
Cheryl dont worry and dont think that you can not handle this device its one of the nicest device ever merketed and you can play with this device allot accept you can not install Windows 2005 in this, such a pitty.
Ok try these settings step by step, please dont be hurry, be calm and try them. Let me know (by-the-way have a look on my XDA-IIi)
**************************************
Go to: Start>Settings>Connections tab
Select: Connections
Select: Advance tab
Select: Select Networks button
Select New... button under the first dropdown
On the General tab
Name: T-Mobile WAP (or whatever you want to call it)
On the Modem tab
Select: New... button
Connection Name: WAP
Modem: Cellular Line (GPRS)
Select: Next button
Access Point Name: wap.voicestream.com
Select: Next button
Select: Finish button
Be sure to reselect your previously working GRPS connects in both the dropdowns if they are changed to the new WAP ones. The new ones will only be used by your MMS application.
Select: OK and close the settings
Next we setup the MMS Application to use the new WAP connection we just created.
Select: Start>Messaging
Select: Tools menu at the bottom of the screen
Select: MMS Settings...
On the Preferences tab
Connect via: T-Mobile WAP (or whatever you called it in the previous setup)
On the Servers tab
Select: New button
Server Name: T-Mobile USA
Gateway: 216.155.165.50
Port Number: 9201
Server address: http://216.155.174.84/servlets/mms
Size: 250k (you might set this smaller)
Select: OK
Select the T-Mobile USA entry and set is as default by pressing the Set As Default button
Select: OK
********************************************************
GoodLuck
Sidd

Internet Connection issues have searched/read faq

I recently flashed to this dutty release. I'm using the 1.27.12.17 Radio on ATT 's network.
For some reason I cannot connect to the internet using internet explorer.
I am able to send and recieve emails with blackberry connect, and I get the weather updates through the weather plugin. When I try to use IE, it never navigates away from the dutty start page.
I have run the connection setup program and I have also tried the following manual steps. Neither seems to work. Any advice would be welcomed.
tap start
tap settings
tap connections tab
tap connections
tap set up my proxy server
uncheck this network uses a proxy server to connect to the internet
leave this network connects to the internet checked
tap ok
tap advanced tab
tap select networks
both should be set to medianet
tap edit on the top/bottom (both are the same settings
tap edit... again
tap next
enter wap.cingular
username [email protected]
password CINGULAR1
tap finish
ok out of all screens
soft reset by pushing the reset button to the top right of the usb port with your stylus.
I've also tried:
To get to the connection settings:
Start Menu/Settings/Connections/advanced/select networks/click "new" if media net isn't there or click edit if media net is there/ fill in these settings:
MEdia Net:
General: MEdia Net
Modem:Edit(MEdia Net)/New(Create Media Net):
Name: MEdia Net
Modem:Cellular Line (GPRS , 3G)
Hit next
Access Point name: wap.cingular
Hit next
Leave first three fields empty(if you know what to put put in but it doesn't really matter)
Hit advanced
Select Use server assigned IP address
Select Use IP Header compression
Servers:
Select Use server assigned address
HIT OK
Hit finished
Proxy Settings:
Select This network connects to the Internet
Select This network uses a proxy server. . . .
Proxy Server: wireless.cingular.com
Hit advanced
Hit HTTP
Port:80
Hit ok
Hit Socks
Server: localhost
Port: 1080
Hit ok
AT&T ISP:
General:AT&T ISP
Modem:Edit(Edit My ISP*Change name to AT&T ISP GPRS*/New(Create AT&T ISP GPRS):
Name: AT&T GPRS
Modem:Cellular Line (GPRS , 3G)
Hit next
Hit next
Access Point name: isp.cingular
Hit next
Leave first three fields empty(if you know what to put put in but it doesn't really matter)
Hit Finish
Hit ok
Lastly, i've tried using Opera Mobile 4 from a har install through Active Sync. none of these methods work.
Any ideas?

Email set up problems with Telstra (AUS)

I have just upgraded from a DIAM 100 to a 130 so now 3G works beautifully.
However my mail set up fails to synchronise (both bigpond and windows live).
It will work on wifi but will not work otherwise (full 5 bars reception and internet does work.)
I figured it must be the settings for my telstra internet/wap setting however when i go into connections, it tells me that this is preconfigured and cannot be modified.
So has anyone else had this problem and how did you fix it.
I have wasted several hours of on hold to Telstra so I thought I would ask this forum first.
I have searched the fora without success for this problem.
Many thanks
thedoc said:
I have just upgraded from a DIAM 100 to a 130 so now 3G works beautifully.
However my mail set up fails to synchronise (both bigpond and windows live).
It will work on wifi but will not work otherwise (full 5 bars reception and internet does work.)
I figured it must be the settings for my telstra internet/wap setting however when i go into connections, it tells me that this is preconfigured and cannot be modified.
So has anyone else had this problem and how did you fix it.
I have wasted several hours of on hold to Telstra so I thought I would ask this forum first.
I have searched the fora without success for this problem.
Many thanks
Click to expand...
Click to collapse
Flexmail for the win!
I have exactly the same problem. I'm assuming the Teltra ROM is locked down and you can't do much with it.
The problem is the proxy settings, don't enter them and you will be able to use msn and email, but you will loose access to the "free to browse" Telstra pages
Copied from http://configure.telstra.com.au
1. On the handset, tap on the Start button.
2. Tap on Settings.
3. Tap on Connections tab.
4. Tap on Connections icon.
5. Tap on Add a new modem connection under My Work Network.
6. Enter Telstra Internet in the Enter a name for the connection field.
7. Select Cellular Line (GPRS, 3G) in the drop down list under Select a modem.
8. Tap on Next.
9. Enter telstra.wap in the Access point name field.
10. Tap on Next.
11. Enter a username in the User name field or otherwise leave it blank.
12. Enter a password in the Password field or otherwise leave it blank.
13. Tap on Advanced.
14. Select Use server-assigned IP address.
15. Tap on OK.
16. Tap on Finish.
17. Tap on Set up my proxy server under My Work Network.
18. Make sure that This network connects to the Internet and This network uses a proxy server to connect to the Internet are checked.
19. Tap on Advanced.
20. Tap on HTTP.
21. Enter 10.1.1.181 in the Server field.
22. Enter 80 in the Port field.
23. Tap on OK three times.
Fix in Advanced Server Settings
I had this problem and fixed pretty easily by going into email inbox tab, then press menu / tools / options then tap an account to change its settings. click 'edit account setup' press next a couple times until you get to a page with "Advanced Server Settings" down the bottom in blue. click on that and change the network connection box from 'The internet' to telstra internet. click done and next til the setup is finished and you should be able to get your mail over the 3G connection

o2 pay as you go setting help plz

sorry if this has been asked a million times before i have been searching for two days trying to get the internet to work on ya sons touch diamond
this phone was on contract on o2 he is now trying to set it up on his pay and go simplisty sim which includes free internet .
I have tryed so many different settings to get the internet working and email
all i get are network error messages.
the only way i can get it to conect is via wifi
and help would be great thanks in advance
Gary
Theres a cab file with the settings in. I cant remember where i got it from, but if you PM your e-mail address i will mail it to you.
I think its called DeploySP.cab
Hi, I'm on the same network and on the Text and Web simplicity tariff. Here is what I did. The Windows mobile version I'm using is wm6.5.x, with the start menu at the bottom left.
To enter the settings first click "start", then click "setting", then "connections".
First click manage existing connections, and delete the modem connection specified in here. (Not required but advised) As this is configured by the device and the setting are incorrect.
Next go back a step. Then click add new modem connection.
“Select a Modem” should be set for “Cellular Line (GPRS)” or “Cellular Line GPRS/3G”
Now click “Next” to start inputting the operator specific settings.
Name the connection: O2 (PAYG)
Access Point Name (PAYG): payandgo.o2.co.uk
Username (PAYG) payandgo
Password: password
Tap “Advanced” and make sure both tabs have selected “Use Server Assigned IP Address”
Tap “Finish” then Tap “Proxy Settings”.
Select “This network connects to the Internet” and “ This network connects to a proxy server…”
Tap “Advanced” then WAP. Server address is: 193.113.200.195: Port 9201. Tap OK
Tap Socks: Server is 193.113.200.195: Port 1080. Type: Socks 4.
I can confirm these settings work as I use the internet everyday on my Touch Pro. Hope this helps. If you struggle pm me.
Hello sb.oddworld,
Working on HTC Kaiser on O2
Many thanks,
SW ;o)

Categories

Resources