Hello guys first thank you for this great site and for this great releases for the BA.
I made yesterday a rom Upgrade with Helmis new rom and now i have a problem.
it freezes in the 4 colour stripes boot image , soft and Hardreset or reflash dosent help.
The only thing i can do is to flash in Wm2003 and it works.
I tried to flash 3 different versions of WM5 and it freezes at the bootscreen or it gives me while flashing 112 errors
i want the WM5 back. i had the ivan version and i whas happy
Thank you for the help
Related
Hello!
I tried to flash my Charmer with the new german Aku 3.3. At first everything seems to be ok, but at 95% it stops and i got the Message: update error- there is an comunication problem! So what can i do? I tried to flash the old rom back but there comes also at 95% a message: invalid command - nfb file cannot be used for your pda!
Please help me !
Greetings Musna!
Ps: can somebody upload a sd image for the mda compact II !
Go to bootloader mode, then try to flash RUU rom (1.x). You can find it on Charmer wiki.
It doesn`t work too, it always stops at 95% has anyone another idea?
did you try hard reset?
Yes i tried hard reset, but it is always in bootloader!
I have also the same problem. Tried to upgrade to version 3.3. Everytime it stops at 80%. I don't know why?! I can repair it with the software and re-run it. But it has the same effect.
Now i will try to downgrade to 2.6 again. I really don't understand what causes the problem. I hope i will get this thing running again....
EDIT: I reflashed the device with the older 2.6 ROM and it is working right now. However I didn't really get why it gets stuck at 80% with 3.3 ?!?!
nitrane said:
I have also the same problem. Tried to upgrade to version 3.3. Everytime it stops at 80%. I don't know why?! I can repair it with the software and re-run it. But it has the same effect.
Now i will try to downgrade to 2.6 again. I really don't understand what causes the problem. I hope i will get this thing running again....
EDIT: I reflashed the device with the older 2.6 ROM and it is working right now. However I didn't really get why it gets stuck at 80% with 3.3 ?!?!
Click to expand...
Click to collapse
The aku3.3 is up to date the bootloader version!!!
IPL and ISP version now is 3.00.
http://www.windowsceportal.hu/forum/viewtopic.php?t=1079
Sorry but i do not speak hungarian. What do you want to tell me ?
I´ve got the same: My charmer is in Bootloader IPL 2.06.0001 SPL 3.08.0001
I can´t downgrade to AKU 2: Please order a newer Version.
Every try to upgrade to AKU 3.3 failed at 95% with Error 326.
Is there any help for my charmer???
oh.**** !!!! I got the same problem with them and my first pda uk rom already empty screen and then i try with my scrond pda German rom it the same problem and now just only show in bootloader screen.Have i ask someone who knowage about this he told me that if SLP in you PDA have chang it be hard to repair.So,I think I lose 2 PDA did I try to flash in T-Mobile Official Rom de that i hope to develop it but i hve to kill 2 Charmer.Who take responsibilities,T-Mobile right ???
Ok no problem you can repair it! At first you have to brand your device with the rom you want to! After 95% the Problem will come again! When it stops you have to go with a reset to bootloader again.When your device is in bootloader you have to install the Radio Rom from this thread:
http://forum.xda-developers.com/showthread.php?t=302768
After that your device will be able to boot again and it should work!- But the Problem during the installation will stay,so you have always to use this way to flash your Mda compact II!
In the new rom there must be a problem with the radio rom and this causes the broken device.
I`m sorry for my bad english but i`m not used to talk very much! So i hope you understand what i mean!
Greetings from Austria Musna!
that link is broken
Then try this one:
ftp://xda:[email protected]/Prophet/Radio_Roms/Prophet_G4_RadioRom_v2.47.11.exe
You can find the radio rom also on the ftp server. Prophet> Radio Roms>Prophet_G4_RadioRom_v2.47.11.exe
You can try different Radio Rom versions, i have flashed the v.247.11 and it worked.
Normaly it should work!
Thank u so much !!! My Charmer secrond PDA come back have life again and it can working.So,my Charmer first PDA UK rom still empty screen and notthing working when i press any button.Who can slove this problem !!
Musna do you have any massage such as msn
Hi guys,
this is one of my first post here but I read you everytime. So, the problem now is: my P3600 don't want to flash with any rom.
I've just take it back from assistance for to change the black cover (2nd time...) and when I want to flash, as before I was given to the assistence, with udK 6.1 rom it don't want to flash with any other roms!!
I've now download the Lite version of udK 6.1 and install it but when I've discovered that I prefer the full version that's start the never ending story: I tryed to flash with Full version 2 or 3 time already, the installation goes to 100% but when it restart (should it restart not power off?!?) the rom is always the same Lite version. I tried to use also the official wm5 from HTC without manual entry into bootloaded but after flashing is 100% the rom is always udK 6.1 Lite. I have SPL Olipro 1.20 installed (in the past I've had no problems at all!)
Anyone can help me to flash (with lowest risks) my P3600 again?
Thanks to everybody!
no ideas guys?
so no one can help me with an idea???
What version is your Trinity? P3600 or P3600i? Just to confirm eventhough you mentioned P3600 in the subject.
jackkkkk said:
What version is your Trinity? P3600 or P3600i? Just to confirm eventhough you mentioned P3600 in the subject.
Click to expand...
Click to collapse
it's a P3600
Do a hard reset and flash an OFFICIAL ROM from SD-card
Switch to Des' Crash Proof SPL and try flashing the ROM straight from SD card.
This should work.
thank you very much. I've already tried to change to Des Crash Proof but at about 13%-14% it gives me an error when I reboot by softreset the system is always the same. Is it normal? Is there a specific procedure to change SPL software?
If it works at all after SPL flashing, then you must have followed all procedures. Try flashing Olipro's SPL and scan for bad blocks in flash.
nightblade said:
Hi guys,
this is one of my first post here but I read you everytime. So, the problem now is: my P3600 don't want to flash with any rom.
I've just take it back from assistance for to change the black cover (2nd time...) and when I want to flash, as before I was given to the assistence, with udK 6.1 rom it don't want to flash with any other roms!!
I've now download the Lite version of udK 6.1 and install it but when I've discovered that I prefer the full version that's start the never ending story: I tryed to flash with Full version 2 or 3 time already, the installation goes to 100% but when it restart (should it restart not power off?!?) the rom is always the same Lite version. I tried to use also the official wm5 from HTC without manual entry into bootloaded but after flashing is 100% the rom is always udK 6.1 Lite. I have SPL Olipro 1.20 installed (in the past I've had no problems at all!)
Anyone can help me to flash (with lowest risks) my P3600 again?
Thanks to everybody!
Click to expand...
Click to collapse
Make sure that your SD card it out
Hi forum.I've a problem flashing my htc p3600. When I'm trying to install a wm6 rom flashing seem to going right...Smartphone restarted correctly but I've blanc screen and i didn't see a lot of icons(for example number on telephone). Start menu working fine. I use olipro 1.20 and radio 1.46.
Any ideas?
Thanks
Djeghe
Hi all,
i have a big problem flashing a new wm6 rom to my wizard. The wizard is CID unlocked following the How to flash a new ROM to your Wizard... a little tutorial! tutorial.
I had 2 WM6 roms on my wizard - 1 of them was WM6 crossbow, which i used a couple of months - both flashed w/o any problem and worked perfectly.
Last day i decided to flash the TNT touch flo rom but the install wizard ended with error on 99%, then i tried the TNT professional + home - same result, then i tried to flash the crossbow rom - same result. Then i returned to the unlocking howto - and followed it again but i can not flash wizard_love rom (ands at 98%) and Xda_MiniS_LaunchROM_v154102 (ends at 85%). I tried the whole procedure many many many times... but unfortunately the only rom i can flash w/o any problems is the t-mobile rom. Nothing else works...
Any help is highly appreciated!
Thanks!
succsess flashing new rom to my wizard
Hi All,
i tried to flash WRCX 2 (TouchFLO) after i flashed the t-mobile rom and i had success!!! I have it now running w/o any single problem .
As i posted above i tried the whole procedure with many other WM6 roms without luck ...
I am wondering what could be the problem here ...
My Qtek 9100 is dead after flashin new rom
After I flashed the newest rom version downloaded from official QTEK website
my 9100 has just 'died' without any signal.....
My previous rom was in spanish I tryed to put the new rom in english version something like 2....wwe and now it came a big trouble...
Somebody can help on this isue?!!
Thanks...
cimi said:
After I flashed the newest rom version downloaded from official QTEK website
my 9100 has just 'died' without any signal.....
My previous rom was in spanish I tryed to put the new rom in english version something like 2....wwe and now it came a big trouble...
Somebody can help on this isue?!!
Thanks...
Click to expand...
Click to collapse
Try to get the phone in Bootloaders (multicolor screen) and flash the Rom with 'RUU_Noid' utility,you can search for this in the forum or read this thread :-
http://forum.xda-developers.com/showthread.php?t=291215
hi
i thought that wm6.1 is faster than wm6.5 so after hardspl flash my new topaz with wm6.1 rom but it didn't start .after soft flashing and rest just shows startup picture and restart again .so i had to reflash it to wm6.5.
the question is how can i use wm6.1 and???
thanx in advanced
farzad23 said:
hi
i thought that wm6.1 is faster than wm6.5 so after hardspl flash my new topaz with wm6.1 rom but it didn't start .after soft flashing and rest just shows startup picture and restart again .so i had to reflash it to wm6.5.
the question is how can i use wm6.1 and???
thanx in advanced
Click to expand...
Click to collapse
I think you would need to downgrade your SPL.
So you would need to reinstall SSPL, then just install HSPL 1.83, then the 6.1 ROM. You will probably have "commercial use" issues to reinstall 1.83 so I would send the Olinex team an e-mail first before trying.
thanx Bruce Inman for u'r reply.i'm waiting for
hi Bruce Inman
I did what you said before.downgarde hard spl to 1.8 ver and then flashed my topaz with wm6.1 cocked and stock but didn't work. in boot session reboot cycling occur.
downgrading spl is not necessary i think, because i have also downgraded 6.5 to 6.1 last week, and my topaz got the latest hspl. last year i downgraded my kaiser to 6.0 and 6.1 with the latest spl.
i think the rom image you acquired is damaged, try re-downloading it
@Carrier
hi
i tested many rom cocked and stock .when i bought this damn topaz it was wm6.5
i think all fu... HTC are slow ,unstable .
I tried the same my self with official ROM from HTC. I didn't have to downgrade SPL because my phone for some reason is unable to be flashed HSPL Olinex ??
Operation run smoothly but after finishing topaz entered a constant reset loop after boot screen
I run out of ideas ...