Please Help!!
I tried to use the aWizard utility and I did the RAPI and CID unlock and tried to install the 1.6.7.1 to my qtek with the original sept 22nd rom. It froze while doing the upgrade (after 3 or 4 mins) and now it gets stuck at the splash screen but it shows the 1.6.7.1. It does not connect via USB anymore and I can only soft reset or hard reset and it goes back to the qtek splash screen and hangs.
Do I have a paperweight?? Is there anything i can do without it being able to connect to USB??
Any help would be appreciated.
Riker.[/b]
Enter Bootloader, - hold the "camera" and shortly press the reset button, don't release "camera" until you can see color screen, connect USB cable, and start to flash any ROM you like from ftp...
Thanks for your help!! It worked perfectly!! I am a long time 'viewer' and have loved all the knowledge that is available on these forums!!
I hope this helps out anyone else who is in a similar situation and is scared they have destroyed their device.
Boy am I relieved!!!
Riker.
OK
Try this funny rom:
ftp://xda:[email protected]/Up...TOM__RUU_Wizard_1050412_WWE_101_11210_WWE.exe
Re: Tried to Upgrade rom --> Crashed --> Now DEAD!! HE
riker said:
Please Help!!
I tried to use the aWizard utility and I did the RAPI and CID unlock and tried to install the 1.6.7.1 to my qtek with the original sept 22nd rom. It froze while doing the upgrade (after 3 or 4 mins)
Riker.[/b]
Click to expand...
Click to collapse
Hi Riker,
The upgrade takes 10 to 20 minutes to complete. If you stop it before it say finish then.... u have to flash ur device all over using upgrade program.
Button said:
OK
Try this funny rom:
ftp://xda:[email protected]/Up...TOM__RUU_Wizard_1050412_WWE_101_11210_WWE.exe
Click to expand...
Click to collapse
Thats unfare!
I may try somethings, but i'm not installing a new rom, without at least knowing what its going to do? :lol:
CID-unlock your Wizard first, please.
hey man..your lucky u got urs to work straight away
im stuck exactly where u r but now when i upload the new rom...nothing happens still..think its because i didnt do cid unlock...but it did say CID is unlocked on your phone now....
well...i just cnt get wait to get this dead 9100 to be bk up again..
Hi friends,
I am very new to upgrading\downgrading pc phones. I was trying to upgrade my wizard to upload diffirent language ROM, using this method :-
http://forum.xda-developers.com/viewtopic.php?t=56088
After some tries, I succeeded to upgrade rom, but after this power on the wizard and it stuck into startup screen.
If I press Camera + Power swich it shows three colour screen and some text :
IPL 2.16. 0001
SPL 2.16 0001
I think my device was CID locked and G4, and that is why I have a dead wizard.
I have backed up the phone before upgrading with wizBackup.exe and I have back files on my hard disk. I dont know how to restore rom from these backup files. :?: :?: :?:
Please help me to revive my PC.
Thanks in advance
Singh06 said:
Hi friends,
I am very new to upgrading\downgrading pc phones. I was trying to upgrade my wizard to upload diffirent language ROM, using this method :-
http://forum.xda-developers.com/viewtopic.php?t=56088
After some tries, I succeeded to upgrade rom, but after this power on the wizard and it stuck into startup screen.
If I press Camera + Power swich it shows three colour screen and some text :
IPL 2.16. 0001
SPL 2.16 0001
I think my device was CID locked and G4, and that is why I have a dead wizard.
I have backed up the phone before upgrading with wizBackup.exe and I have back files on my hard disk. I dont know how to restore rom from these backup files. :?: :?: :?:
Please help me to revive my PC.
Thanks in advance
Click to expand...
Click to collapse
Your phone is not dead!!!
If you can get to the three color sceen then your botloader is intact (and preserving the bootloader was the point with the tutorial that you followed).
Your phone is CID locked and is G4, that's right, but this is NOT the reason for the problem. The tutorial you followed, which incidentally I wrote, deals with CID locked G4 phone like yours.
The problem you had is probably due to a not correctly cooked rom.
Anyway, don't worry. You got the three colors screen so you can connect your phone to USB (even if activesync won't recognise it) and flash your factory rom (the one you were trying to replace). Don't need to use your backup: simply download the original rom from the manufacturer/operator site.
bye
After many tries now my phone is working again,
I downloaded RUU_Prodigy_2170702_21707102_20710_QTEK_WWE_Ship from internet then cooked its nk.nbf file.
then uploaded the rom and phone is working again. Thanks for your help
Singh06 said:
After many tries now my phone is working again,
I downloaded RUU_Prodigy_2170702_21707102_20710_QTEK_WWE_Ship from internet then cooked its nk.nbf file.
then uploaded the rom and phone is working again. Thanks for your help
Click to expand...
Click to collapse
I glad you worked it out!
Bye
hello. I have similar problem. I upgraded my wizard to AKU2.3 and now phone doesn't start. It start showing splash screen with the information:
IPL:2.24
SPL:2.24
GSM:02.25.11
OS:2.24.10.1
HOW to fix this problem ?
hi guys
i have qtek wiza200 today i'm use MrClean_RUU_WIZARD_224a_AKU23_WWE.zip after flashing my phone turn on and installing all soft and restart and dead my phone. i'm push camera+power+reset i can't enter to boot mode. help me to repair my cellphone and how resolve my problem. my phone forever dead????
thanks a lot
Urgent helps needed!
So i bricked my Cingular 8125!
I just wanted to upgrade my ROM to the newest AKU 3.2 from Faria.
I did ungrade and errors arised as i described above.
I was told that the fone hadn't been CID unlocked.
I did as what described in lowikiz
-downgrade the rom,
-run enablerapi.cab on my device
-run lowikiz 0.2b
-choose CID unlock
Restarted the fone, what i saw was:
IPL 1.01
SPL 2.25
GSM 2.47.11
OS 3.0.0
There're only two things fulfill me,that's GSM and the OS.I wanted the
IPL and SPL should be 2.26 or later version.
What i did then :
-Downgrade again (hoping that i forgot to SIM unlock)
-run enablerapi on my device
-run lowikiz 0.2b
-choose unlock
And when the fone restart.
What i saw was:
IPL 1.01
SPL 1.01
GSM 1.x.x
OS 1.05.x
when the installation completed, i upgraded the ROM again to AKU3.2
everything went smoothly until it finished.The fone restarted and what i saw was:
IPL 1.01
SPL 1.01
<blank, no GSM version, couldnt believe that>
OS 3.0.0.0
the device kept running until the installation completed.
It restarted again and stopped running.What i can see now is just
nice background and blinking (waited for nearly 15 mins but no futher responses)
IPL 1.01
SPL 1.01
OS 3.0.0.0
It couldn't get further.
I think i bricked my Cingular 8125.
So could you helpers, experienced users help me with that?
Can i fix it?Or can HTC fix it?
Thank you very much!
mod edit;
the title has been changed as you did not have a bricked phone...if you ever brick you phone belive me,,,u cant restore it at home.
regards
faria
It's not bricked. As long as you can go into bootloader mode, and flash it with Cingular clean ROM you should be fine..
Have you ever read the note from faria? He said NOT to upgrade to AKU 3.2 without IPL/SPL version 2.xx.
You can try to take out you're SIM card, go to the boot screen by pushing the cam button and the on button and flash it again with te original ROM.
Good luck
Sorry for my bad English
or you can try it this way: link
just go into bootloader (camera button + soft reset) and flash that 1.5 ROM, which is able to downgrade.
and then
!Do !NOT! install any 2.x ROM (like farias ) for the 1.x bootloader (ipl/spl)!
before it you could flash any official 2.x ROM ;-)
I'm pretty sure that this was resolved in another thread and not updated here...
Dr Puttingham said:
I'm pretty sure that this was resolved in another thread and not updated here...
Click to expand...
Click to collapse
You are correct.
--M
(granted there may be a lot of pages to read through to get to the information...but a solution was posted.)
Yes I was pretty sure I saw it resolved in another thread, might have even helped...
Ahh, the joys of posting across threads... makes me feel oh so nice!
Thanks
Thank you friends for all those things.
Things seem to get worse, I couldn't even turn the fone on.I had full charge of batt. before upgrading .After that "accident", i left the fone alone for one night, when i woke up in the morning, tried to turn on the fone but i failed.Tried to enter bootloader mode but failed.The fone now becomes a brick.
-Do you friends know how to revive my fone?
-Do you know where can i have it revived?
Thanks for all!
Leave the battery out for few days, then try again after full charge in BL mode.
TIA
BL Mode????
almozaffar said:
Leave the battery out for few days, then try again after full charge in BL mode.
TIA
Click to expand...
Click to collapse
------------------Thank you very much almozaffar and friends!But how can i full charge the batt. in BL mode?I just have the wall charger as included in the box, a USB cable.What i need in BL mode?
I find no red LED(indicating that the fone's being charge)when i connect the fone with my wall charger as well as with the USB cable.I realise that the batt. gets hot but i'm not sure if it's charged.
Best regards
Someone just told me to remove the batt. for about 2,3 days then recharge, i'm not sure if that works but i'll try.Thank you!
Same problem here!
I have a Cingular 8125, I tried to update it to MDA with IPL/SPL 2.26. I was successfully flashed it. After it turn on, everything work fine, so I turned it off, so that I can inside my sim card. After I inside my simcard, my phone is now can never turn on again. I tried and tried again, there was no used. I plug in the power to the phone, there is no power. When I unplug the power, I see a flash from the screen, or after I remove the battery I see a flash from the screen. I have no idea what it is doing, but i can't turn the power back on. Can some please please help me!
Thanks,
Bricked fone huh? No way!!!
After researching the Wizard, i know how to revive it and do not have to spend a cent!Anyone interested?Please PM me!I'll post later when i have time the whole procedure.
@unknown84: I send u file on how to revive your fone.
How to revive your 8125.
Friends,
First remove your main battery, then plug and unplug the wall charger connecting to your fone, if the RED LED and your Fone screen flash then you can revive your fone(at least it works with my fone,wish you good luck!)
Read these lines carefully before you proceed to the procudure.That really works with my phone(i'm not sure if it works with your fone but i wish you good luck)
*Preparation:
1.Charge the main batt. for 2 hours long.
2.Remove your main batt., charge without the main batt. for 1 minute.
3.Plug and unplug the wall charger for at least 3 times ( main batt. removed) (you'll find that your fone keep flashing, both LED and your Fone screen, by doing this i hope it'll help with waking up the backup batt.)
4.Download the official Cingular 8125 ROM version 2.25(you can find it everywhere)
-Three ways to enter bootloader mode:
a.Hold firmly CAM + Power until Bootloader Mode appears
b.Hold firmly Voice Dial,Rec Button + Power until Bootloader Mode appears
c.Hold firmly CAM + Voice Rec + Power ........
*Procedures to followremember to remove your main batt. before doing hereafter)
1. Hold simultaneously 3 buttons : the CAMERA button, The Voice Recording Button, and the Power button.(or follow one of three ways to enter bootloader mode listed above)
If this doesnt work, do that again by holding those buttons, plug and unplug the wall charger and still keep holding those buttons
(as PLUG and UNPLUG the wall charger, you'll see the Red LED and the screen FLASH, i guess it's the way to WAKE our backup batt UP)
2. Hold those buttons will start the bootloader mode.
3.When your fone's already in the bootloader mode, put the main batt. in
(I'm sure u know what u'll do next if u can start the bootloader mode!!)
4.Unplug your wall charger
5.Plug in the USB cabble connecting to your PC.
6. Start flashing with your 2.25 ROM.
Note: When your fone's in its bootloader mode you can find out if u have a G3 or G4 chipset easily by
looking up at its IPL and SPL. G3 comes with x.xx( ex: 2.25)in both IPL and SPL.G4 comes with x.xx.001 in both IPL and SPL.
If u have a G3 chipset, do as i told u above. If u have a G4 chipset, just download the official ROM for your G4.
Good luck and don't flash again without reading carefully!
battery trick
Congras.
So the Battery trick works. I learned this trick even from motorola phone and apllied it to my 8125.
Now thank you for the newtrick you just detaled us with, appreciate itvery much.
TIA
almozaffar said:
Congras.
So the Battery trick works. I learned this trick even from motorola phone and apllied it to my 8125.
Now thank you for the newtrick you just detaled us with, appreciate itvery much.
TIA
Click to expand...
Click to collapse
=========
You're welcome almozaffar, you did help me with this to find a solution for our users' troubles here.
Thank you too :-D
I have brick
Could you please write for how long did you repeat the steps that you described, before getting BL screen.
THX
Still bricked
It certainly doesn’t work for me. Screen & led flash when taking out usb plug without battery, but that all.
simmilar problem
My HTC Wizard is having simmilar problems but even following these directions, I still cannot revive it.
I know my battery is almost full because when it died it was full. I don't know anyone else with a Wizard so I can't charge it, and this may be where the problem lies: Weather or not the battery is in my phone, whenever I connect wall power, it displays the message "Press send to restore...." and will not charge
When I plug/unplug the wall power with the battery removed, my screen does flash along with the red LED, but only once when I pull the power. Following the directions I have removed the battery and I'm plugging in the wall power jack in an attempt to enter bootloader screen. But just like every time, about three to four seconds after I plug it into the wall, the phone posts the "Press Send to restore factory, blah, blah blah". I don't know if this is part of the problem but it might be.
I've tried almost everything i found on forums, and what I can think of but still to no avail. I can't get my Wizard to enter bootloader mode. I've also tried every method to enter bootloader mode that I could find :/
any suggestions?
I downloaded a wm6 upgrade pack from Demonoid. The instructions told me that I needed to load an older rom on before I could CID unlock. The ROM was: CUSTOM__RUU_Wizard_1050412_WWE_101_11210_WWE. The ROM that was originally on my 9100 was the lastest from Qtek. My Qtek now will not move on from the splash screen. Does this sound like I have a dead pda? Anyone have any idea how to get out of this problem. Any advice or comments would be appreciated.
Thanks
PS: I turned it off for the time being. Now I can't even turn the dam thing on!
I think I may have found a solution if I can just turn it on!! Won't charge either!
Well if u can get it turned on hold the voice and cam buttons and get it into bootloader you'll be good
I was updating my wizard and at 57% it stopped and i was waiting for an hour and nothing changed so i unpluged the usb. Now there is only RGB screen and when i connect to my computer active sync doesnot detects my pda. Please Help! Its G4 device and i dont know whethere is it CID locked or not.
G4 phones cannot be CID unlocked,Which rom were you trying to flash ?
It can be upgraded to wm6 through SoftSPL or HardSPL,read about it in the G4 forum posted as Stickies.
Download the official rom or the wizard_love rom to recover back.
thanks it worked
thanz !
You are welcome