"NO GSM" error after upgrade PDA2K from WM2003 to - MDA III, XDA III, PDA2k, 9090 Software Upgrading

Dear folks,
After upgarding my PDA2k from WM2003 to WM5, an error "NO Gsm" was displayed with system boot. Anybody has experience such a problem like this and could resolve it?
Latest Device Information after upgrade:
Oprator Version: AKU3.3
Rom Verion: 5.04.06.WWE
Rom Date: 03/02/05
Radio Version:
Protocol Version:
ExtTom: 13
CPU: Intel(R) PXA263
Speed: 400 MH
Flash: 32 MB
Ram Size: 96 MB
Falsh Chip: 28f128k3
Data Bus: 32 bits
Storage size: 60.30 MB
LCD: 240 x 320 TFT
Colors: 65532
Mode: PH20B
Platform: Pocket PC
Imei:
Caller Duration: Can't be accessed
please help.
Thanks

Happened to me, but disappeared after the first reset.

Brazilian Joe said:
Happened to me, but disappeared after the first reset.
Click to expand...
Click to collapse
________________________
Thanks for your feedback. Idid so mant times; it won't function.

aku 3.3? where?

No Radio ROM / GSM on reset - possibile solutions
I've had this problem too. After playing a few times with upgrade/downgrade to WM5/2003SE, there are some times when a simple soft-reset will work, and sometimes when it won't. You'll know whether it'll give you GSM by checking whether the Radio ROM version is displayed on the boot loader screen (bottom right hand corner immediately after a soft reset) . If it's 0.0 or similar, then try re-resetting -- this may fix it.
I also had a problem where I either installed some really rogue software that ruined the radio somehow, and wouldn't resolve with umpteen resets. In this case, I just flashed the radio ROM again. If this doesn't work, then you may consider hard-resetting, reinstalling the Radio ROM and WM2003 at the same time, then re-upgrading to WM5 if necessary.

My PDA2K did this with all the WinMo 5 roms I used.
What I finally figured out which seemed to work with me, is that if I took the battery off the phone or did a soft reset with the stylus I would not have my Radio Rom.
If I used software to perform the soft reset it worked fine. So I put 2003 back on my phone and it seems to work fine with that.

Related

BA / WM5 / Radio 1.06 upgrade

Any advice on how to achieve the upgrade. I have attempted with BAUpgradeUT and and MAUpgradnoid without sucess. My Rom version is 5.03.02 WWE (3/2/05) Radio Ver - 1.06.00, Protocol Ver 1337.38, ExtRom Ver - is blank. Getdeviceid recognises as a PH20B.
Using BAUpg is don't recognise device
Using MAUpg it correctly identifies CE image ver5. it goes to check information on device, Activesync shuts down, then Error 101 connection error
Any ideas ?
Connection error....
Have you tried putting the device into bootloader mode before cradling it?
I initially had the same problem upgrading my BA.
Press camera (media), record, power all at once while you reset. The screen should display "Serial" until you cradle the device, then switch to "USB."
Make sure you run the upgrade program twice, it often fails the first time.
Hope this helps, post again if this doesn't work.
Mick...

Need help upgrading ROM

I have tried upgrading 5-8 times with different upgrades. I am running :
ROM version 2.17.7.2 WWE
ROM date: 2/10/06
Radio: 02.07.10
Ext Rom: 2.17.7.102
I have an unlocked Qtek 9100. I continue to get the error message :260, (according to the recovery process means port open.)
No matter what I have tried nothing seems to work. I have disableld McAfee(my anti-virus) I have tried re-starting both machines. I don't know what else to do.
Did you figure this out yet? I'm in the same boat.
TMO MDA, with stock 1.2 ROM. Can't read a 2GB miniSD card that I can read in a PC. TMO tells me the ROM won't support over 512MB, so i am trying to upgrade. Every thing I try ends in a 260 error.
Yikes!

Upgraded to WM5 ROM, 1.15.00 radio doesn't work?

Hi,
I upgraded a Cingular SX66 unit using maupgradeut_noid and the latest AKU 3.5.2 WM5 ROM. Afterward, I had no radio ROM so I updated to the 1.15.00 release. However, my phone is still unable to make/receive calls or data (with multiple good SIMs.) It appears the radio ROM is having issues with this WM5 package because sometimes on hard restarts the boot screen lists R: and G: as NONE, but after a soft reboot they usually show the correct versions.
I searched and can't find any postings about this type of behavior. Nothing useful to report from the phone other than it says "phone is not ready" and "no service" with a good SIM.
I have several of these PDAs that I want to distribute to my internal staff with WM5 so they don't have to learn WM2003 (all of our other devices are WM5 or WM6.) Any recommendations on a procedure to test the radio ROM or a different combination of OS and radio ROMs?
Thanks for the help.
PS. running getdevicedata.exe yields the following:
PH20B1 WWE A %CID? 5.35.05. 1.15.00 % 4
downgrade to wm2003 and try to flash again radio 1.15 and post the results
sandimashsfootballrules said:
Hi,
I upgraded a Cingular SX66 unit using maupgradeut_noid and the latest AKU 3.5.2 WM5 ROM. Afterward, I had no radio ROM so I updated to the 1.15.00 release. However, my phone is still unable to make/receive calls or data (with multiple good SIMs.) It appears the radio ROM is having issues with this WM5 package because sometimes on hard restarts the boot screen lists R: and G: as NONE, but after a soft reboot they usually show the correct versions.
I searched and can't find any postings about this type of behavior. Nothing useful to report from the phone other than it says "phone is not ready" and "no service" with a good SIM.
I have several of these PDAs that I want to distribute to my internal staff with WM5 so they don't have to learn WM2003 (all of our other devices are WM5 or WM6.) Any recommendations on a procedure to test the radio ROM or a different combination of OS and radio ROMs?
Thanks for the help.
PS. running getdevicedata.exe yields the following:
PH20B1 WWE A %CID? 5.35.05. 1.15.00 % 4
Click to expand...
Click to collapse
Take it easy
all BA HAVE THE SAME PROBLEM AS YOU DESRIBLE
IF YOU USE WM2003 THE PROBLEM WILL DISAPPEAR~ SO,JUST SOFT RESET
YOUR PHONE EVERY TIME YOU CHANGE YOUR BETTERY!!
just one softreset, and when you need to charge, charge it when it reaches the 40%, etc, just don't take out the battery, or you will have to softreset it again for the radio work.
it is just the same with mine sx66, and i don't care at all.
Thanks for the notes...I kind of learned the soft reset 'fix' on my own, a little disappointing but I guess we're stuck with it. Why would I want to downgrade my phone to 2003? The whole point was to move to WM5 so my users and support team all work with the same interface.
Of course...my next project is to find out why SMSplus works on 8525 phones and not 8125 (standard Cingular OS load.) Might have to upgrade the 8125s to WM6 (sigh)

Stuck in BA WM6 Upgrading

I'm Stuck in BA WM6 Upgrading.
I was at the HTC_Blueangel_WM6_Wizzard Upgrade 4
After execute the installer file I performed a Hard Reset
Colored stripes (the bootscreen) will appear on the screen but I can't ge no debugger screen at all: the BA remain in Bootscreen with R 1.11.0 at the right bottom of the screen.The battery was full. I've tried the mtty procedure as well...no way out. Any clue ????
Have you follow all this steps here?
http://wiki.xda-developers.com/index.php?pagename=HTC_Blueangel_WM6_WizzardUpgrade1
Yes I did and now I'm Stuck at
http://wiki.xda-developers.com/index.php?pagename=HTC_Blueangel_WM6_WizzardUpgrade4
And what device do you have in fact? Qtek 9090? Other??
Mine is a Qtek 9090 and didn't have any trouble...
Same problem here, wm6 was already running; downgraded to 2003 SE to repartition the extrom, wanted to flash to wm6 again; now my xda3 is stucked after flashing, only r 1.10.0 is shown, no chance to carry on...???
I've got imate pda2k ct2cwj...and Heinzibua I'm stuck on R 1.11.00 do you have an Imate as well ??? cause I guess the official XDA procedure doesn't work for this kind of model (mine was an Italian W2003).
I'm very upset about this...
@ conosciani.m
wm6 worked well on my xda3 , problem was only after repartitioning the extrom.
I'm going to think I did somenthing wrong during the extrom steps..so i've returned back to wm2003 and I'm going to try the upgrade again
please tell me, if you find the solution...
running again
i repartitioned storage in 2003SE set to 20000 kb.
flashed to WM6, no problem now, storage is 41,25 MB, but running !!!
I did it too, I had to reinstalled w2003 and dit the Upgrading BA WM6 wizard again.....
after UNHIDE the rom, this time (and not in the previous upgrading), I did it the rom format using MTTY after that I ran the upgrade procedure and I got the WM6 running.
Happy for both of us to reach the goal......
do you have 60 MB storage now ?
can you give me more infos about MTTY ?
thx
tried to set storage to 60mb again, stuck again, also if i do just the same procedure as yesterday it is stuck; start to hate this device.
please tell me, what you did exactly to make it run. tried mtty also, but don´t know, what to do...
try this...
1. downgrade to 2003
2. copy the utils to the phone(extrom utils and repart_doc.exe)
3. install extrom utils...
---a. tap unhide... ok.
---b. tap unlock... ok. may throw an error but still ok...
---c. reset...
4. run Repart_DOC
---a. Set it to 128 byte
---b. Go/Start/Format (it should succeed)
5. reset to bootloader
---(press and hold record + power button then stick reset)
6. flash WM6 ROM
7. cold boot (press and hold power button then stick reset)
8. (optional) if stuck in the "tri-color"(white isnt a color ) screen...
---Hard Reset. Using No/Yes/Yes option.
reading further about the Repart_Doc topics...
128byte is the smallest you can format/resize the extrom
to maximize the storage in WM6.
Thx, that´s exactly what i did many times without success...
but now it works, after upgrading radio rom there also was no problem with upgrading to WM6; 60 MB rom; i only want to upgrade to radio rom 1.15, then i´m happy.
thx everybody for your help

I am stuck in 4 colored screen or can't exit BootLoader (softreset didn't help)...

Hi folks,
i tried the upgrade like in "HTC_Blueangel_WM6_Wizzard" is discriped,
but after a hardreset i can't start my device or get in debugger screen!
I only see the boot screen with "R 1.10.00" displayed.
Any help would be welcome!
My device
Modell: PH20B1
CPU: Intel PXA263 400 MHz
RAM: 128 MB
Flash: 32 MB
ROM: 1.31.01 GER 12/13/04
Radio: 1.10.00
Protocoll: 133.7.391
ExtROM: 1.12.169 WWE
iso
i also experience this problem. can any one help us?
iso0815 said:
Hi folks,
i tried the upgrade like in "HTC_Blueangel_WM6_Wizzard" is discriped,
but after a hardreset i can't start my device or get in debugger screen!
I only see the boot screen with "R 1.10.00" displayed.
Any help would be welcome!
My device
Modell: PH20B1
CPU: Intel PXA263 400 MHz
RAM: 128 MB
Flash: 32 MB
ROM: 1.31.01 GER 12/13/04
Radio: 1.10.00
Protocoll: 133.7.391
ExtROM: 1.12.169 WWE
iso
Click to expand...
Click to collapse
Press Power + Softreset, and when the colored stripes (well, this is the bootscreen )shows on the screen.
If you have a PH20B device such as MDAIII, QTEK 9090, XDAIIs, PDA2K etc.
Quickly press Record+Camera before the versions appears at bottom right
OR, press Power+Softreset+Camera+Record at the same time.
If you have a PH20B1 device such as SX66
Quickly press Record+Windows Media before the versions appears at bottom right
OR, press Power+Softreset+Windows Media Player button+Record at the same time.
Either way mentioned above should work.
You'll see three options; change the second and the third to "yes".
If you have a PH20B device such as MDAIII, QTEK 9090, XDAIIs, PDA2K etc.
You can do that with the camera and the record buttons.
If you have a PH20B1 device such as SX66
You can do that with the Windows Media Player and the record buttons.
If you are done, press the mail button, it'll show a white screen for a while, just wait.
If the bootscreen, aka. the colored stripes is displayed, Wait more, you are booting.
The welcome screen to set up your device should appear soon.]
I hope this will help to resolve the problem
Take Care
ENJOY
Old Bootloder?
Software Solutions said:
If you have a PH20B1 device such as SX66
Quickly press Record+Windows Media before the versions appears at bottom right
OR, press Power+Softreset+Windows Media Player button+Record at the same time.
Either way mentioned above should work.
Click to expand...
Click to collapse
THX for your hint, but this is what doesn't would work!
When i press the two buttons, like you descriped and it is shown in wiki, no meue is shown?!
Maybe Bootloader of my BA is not the newest? = R 1.10.00
Could you tell me how i can update it?
iso
iso0815 said:
THX for your hint, but this is what doesn't would work!
When i press the two buttons, like you descriped and it is shown in wiki, no meue is shown?!
Maybe Bootloader of my BA is not the newest? = R 1.10.00
Could you tell me how i can update it?
iso
Click to expand...
Click to collapse
The bootloader is included in the ROM that you flash onto the device so that is not the issue. You must press the two buttons and hold them until the menu appears. It may take several attempts to succeed. The R that you are referring to represents Radio and has absolutely nothing to do with anything other than GSM operations.
Kasush said:
The bootloader is included in the ROM that you flash onto the device so that is not the issue. You must press the two buttons and hold them until the menu appears. It may take several attempts to succeed. The R that you are referring to represents Radio and has absolutely nothing to do with anything other than GSM operations.
Click to expand...
Click to collapse
okay... thanks for you info, but...
if R 1.10.00 is not the version of Bootloader i got no other on screen.
I pressed the record and media button while reset and after.
I pressed the buttons similar and step by step.
I pressed the buttons after battery reconneced.
I wait after reset without pressing buttons... nothing more happens then a screen with stipes an "R 1.10.00" is displayed in right bottom.
Buttons were working fine while i used WM2003 SE on the device, so i think bottons are not the problem... but where is the bug?
I am getting crazy... ???!
Maybe i should use a other rom?
Or try to use mtty? (see above)
iso
Added:
I used mtty like discriped in http://wiki.xda-developers.com/index.php?pagename=BA_FAQ_STUCK_AT_STARTUP but after Reset no difference... :-(
So, in the three stripes screen you only see R 1.01.00 and no G xxxx.xx nor D x.xx.xx.xxx ?
Maybe that means that you have no OS installed. Have you tried reflashing the ROM ?
Also, which ROM and program are you using to flash ?
JP
i dont know about R G and D terminologies...
but we think "R 1.10.00" stands for your RADIO Version... not the ROM.
and since you're not showing the "G xxx.xx" and "D x.xx.xx.xxx"...
i second JP... it's a bad ROM Flashing...
try to flash back the old rom and retry the upgrade.
Used tools..
THX for helping me...
I only used the tools of "HELMI_BA_WM6_R0_Public" archiv FLASH.
GetDeviceData.exe
MaUpgradeUt_noID.exe
RUU.conf
RUU.dll
EnterBL.exe
nk.nbf -> wm6-rom
and i have installed MS-Activesync 4.5.
I flashed the original o2-rom back and it works. WM2003 SE booting.
Than i flashed the HELMI_BA_WM6 and it was completed with 100%, no errors, but then after hardreset the same screen with stripes an R 1.10.00
Any more ideas?
iso
Same for me.
Any solutions?
Maybe this is helpful for you
bj_b4
Guys i think i have a similar problem.
I flashed my BA many times and it worked, back and forth WM5 to WM6 and so forth, until on Fri. I had accidentaly moved files and then deleted them from the windows dir. When I flashed the then WM6 to downgrade to WM5, it worked. When I used DOC resize tool to format my storage (didn't know about th mentined method) as usual (this worked many times before) & flashed to to WM6 then it got stuck at the 4 colors.
I tried what is wrote here and I am stuck at the white screen. nothing happening. It's been like that for an hour now. If i soft reset it, and try again it's the same nothing has changed.
any ideas?

Categories

Resources