Im having problems with my g4 and roms...help - 8125, K-JAM, P4300, MDA Vario Software Upgrading

or is this pretty much because i have a g4 this most roms dont work??

You can't flash a G4 with a G3 rom that includes a bootloader and vice versa. You're lucky you haven't ruined the phone by now. Spend a minute and look through all the posts already here about this subject.

i know that,, i havent tired
but even when i download the rom for a G4, they work.... but not fully... no extra programs where put on.... i was able to set up my GPRS settings manually so that worked.... but no MMS txt were workin...

i just finshed downloading molskis
new 30mb rom... i downloaded the G4 WWE verison... but do not kow if i need to CID-unlock my g4wizard.. i have lizowlki0.2b to unlock it.. but was told i didnt need 2

DankSmoker420 said:
new 30mb rom... i downloaded the G4 WWE verison... but do not kow if i need to CID-unlock my g4wizard.. i have lizowlki0.2b to unlock it.. but was told i didnt need 2
Click to expand...
Click to collapse
As far as i know you need to CID unlock first if you have a wizard as part of an operator contract.
My wizard is not tied to any operator and i installed and have been running this G4 WWE ROM for about a week with no problems at all.
I have set up the WAP settings manually for my operator but have not figured out yet how to get the MMS folder in messaging
good luck

AirwolfUK said:
As far as i know you need to CID unlock first if you have a wizard as part of an operator contract.
My wizard is not tied to any operator and i installed and have been running this G4 WWE ROM for about a week with no problems at all.
I have set up the WAP settings manually for my operator but have not figured out yet how to get the MMS folder in messaging
good luck
Click to expand...
Click to collapse
Yes i downloaded a rom.. and had the SAME problem... but also the extra progrms that came with the rom didnt work as well....along with the MMS folder... *shrugs* i cant even figure out how to unlock my g4... ive tired with lokiwiz0.2b but it dont work

It's impossible to CID unlock a G4 phone without "paying" for it...
For the MMS folder, take a look here: http://www.molski.biz/myroms.html

Related

A helping hand needed to upgrade my MDA Vario!

Hello guys!
I got my MDA Vario last week, and I am very much impressed with it!
I got the MDA Vario brand new without a contract and my intention is to use it with one of those O2 Genie PAYG SIM cards. So.... after much reading this excellent forum I figured out that I would need to unlock the SIMlock on the Vario. Got hold of the Lokiwiz utility, followed the advice on these forums, and tested it with the Orange SIM in my regular phone, and hey presto.... MY PY PHONE IS UNLOCKED!
Next step - to remove all T-Mobile customisations. Again, I had a simple bit of advice from one of you good folk - hard reset, then soft reset when the phone starts to install customisations and now all the pink girlie stuff has gone! Only reminant of T-Mobile left on the phone is the logo on the phone dial keypad.
My thoughts are now with upgrading the ROM. T-Mobile have been very slow with updating their ROM package -a new one is apparently due very soon. Now.... in preparation of installing a new ROM, Ive CID unlocked my phone. I would really like to know which ROM I should upgrade to - there are so many out there! As the phone has been CID & Sim Unlocked, does the phone remained unlocked irrespective of what ROM I install? Can I install a T-Mobile ROM after changing it to another?
As I intend to mostly use an O2 PAYG SIM in it, would it be better to use a new 02 update? If so, which one? Or do I go for another ROM? All very confusing! Finally, Ive heard that I cannot browse the net via GPRS on an 02 PAYG SIM. Is that true? Do I need to flash an ExtROM too?
I know Im asking a lot here and am being a bit of a pain in the backside, but I would really appreciate any and as much advice as possible as I realy dont want to end up with a dead phone! Many thanks in advance!
Hi, yes you could wait for the new rom and i am a believer in sticking with your manufacturer roms because many of the posts here seem to people experimenting with different roms and it all going wrong - lol.
But if you do upgrade proberly the commonest choice is the aku2 qtek rom that i use
download here ftp://xda:[email protected]/Wi...digy_2170702_21707102_20710_QTEK_WWE_Ship.exe
and the o2 aku2rom not a bad idea too, but without the o2 extras.
Yes you could then upgrade to the t-mobile rom then but often you need to unlock again with lockiwiz 0.3a.
PAYG o2 will browse internet but msn etc.. does not work.
btw yes you are a pain in the arse but then most people here are!! :lol:
Cheers Mark! Nice to have some basic advice - very reassuring for a thicko newbie like me!
Well... I couldnt wait for the new T-Mobile ROM and went ahead with the upgrade with the Qtek upgrade you suggested.
Was a little tricky at first because the upgrade wouldnt happen (port failing to open) but I had a few programs running in the background on my desktop PC and shut them all down so that I had a `Clean` PC. The upgrade process was then as smooth as a babys bottom.
MDA Vario is running really well - well worth the upgrade IMO. Everything seems quicker and generally better. Only problem I have is with wifi - it seems to take ages to make a connection with my PC (ad-hoc peer to peer) whereas on the original T-Mob ROM it was very quick. Any ideas here?
I read that you say I would need Lokiwiz 0.3a to install the AKU2 T-Mob ROM when it is eventually released. I was under the impression that once the PDA was unlocked (lokiwiz 0.2b) I wouldnt need to unlock it again. Is it different with the very latest T-Mob ROM? Can I not revert (downgrade) to the original T-Mob and then upgrade to the new T-Mob ROM? Ive not heard of lokiwiz 0.3a being out yet - would it be as simple as unlocking with lokiwiz 0.2b?
Finally, how on earth do I get the latest 02 ROM? I need to enter my 02 mobile number and IMEI to download it. Do I need lokiwiz 0.3a to install that or any other current ROM?
Cheers for your friendly advice.
Al.
Hi, no problem - glad to help.
Lokiwiz 0.3a is out see here http://forum.xda-developers.com/viewtopic.php?t=50768
For some reason when upgrading (in think it renews cid/spl) to aku2 rom seems to lock again - i had to unlock my qtek with above tool.
Yes you can go back to original rom - but if does not work use farias method of unlocking and downgrading rom (post is in this forum)
Most of the roms are in the wiki http://wiki.xda-developers.com/index.php?pagename=Wizard_Upgrades
including the o2 roms, but i would refrain from too much chopping and changing because you can destory the bootloader and then has to go back to the manufacturer.
Many reported problems with the wifi setting up - i would read some of the threads in the wizard forum if i was you. First thing to try is tweak wifi on device to wlan g and it may work better.
see registry tweaks here http://wiki.xda-developers.com/index.php?pagename=Wizard_Upgrades
btw good to hang out in the wizard forum too - you will learn alot of tips from there.
Want to also say thanks from another newebie with T-Mobile MDA. Have unlocked phone and CID and flashed with 2.17 QTEK ROM and all is good.
Thanks !!!
if you want th get rid of the tmobile crap on the face...use a 2p coin and move it downwards...not accross
it takes the tmobile paint etc off without any marks..
Jesus sbouri that logo was killing me, brilliant tip, nice one mate!!!
hi
i just got my mda vario and manage to unlocked the phone with lokiwiz03. i know my phone is now sim unlocked, but how do i check if it is cid unlock as well?
i am eager to flash the rom with the qtek version but i have no idea how to do it.
i know i must have my phone cid unlock in order to install a different rom, so do i just download the latest qtek rom, connect my device to usb and activesync it, and then just run the RUU?
i am really noob here.
cheers.
Hi mate if i was you i would use MR CLEANS ROM i flashed with that and its excellent, tottaly clean with no tmobile crap and i didnt do anything with the cid so dont worry.
ftp://xda:[email protected]/Uploads/Wizard/ROMS/MrClean_RUU_WIZARD_224_AKU23_WWE.zip
Just download this and run follow instructions, real easy. Good luck mate.
thanks for the advice...i took a bold move and flash it with a qtek rom. works like a charm. before that i did cid unlock using lokiwiz02a, not lokiwiz03.
i will take a look at mr.clean rom at a later stage.
i notice that my imei number is different from the one in my box. does flashing the rom change it?
now my next task would be update to a better radio rom and check out the extension rom.
cheers.
SBouri said:
if you want th get rid of the tmobile crap on the face...use a 2p coin and move it downwards...not accross
it takes the tmobile paint etc off without any marks..
Click to expand...
Click to collapse
Great tip, worked like a charm and left no marks.
Thanks.
Hi there, I'm about to flash my UK MDA Vario too.
I'm not sure to use the Mr clean one or the Qtek 2.17 version.
Before I do anything, which is better of the two?
Also, what settings to I need backed up? I have my txt msg service numbers, as well as voicemail. And all of my MMS & GPRS settings.
Am I to assume that all I have to do is input the settings into the device once it's been flashed?
Thanks
Scottland said:
Hi there, I'm about to flash my UK MDA Vario too.
I'm not sure to use the Mr clean one or the Qtek 2.17 version.
Before I do anything, which is better of the two?
Also, what settings to I need backed up? I have my txt msg service numbers, as well as voicemail. And all of my MMS & GPRS settings.
Am I to assume that all I have to do is input the settings into the device once it's been flashed?
Thanks
Click to expand...
Click to collapse
The mr clean rom is a more advanced rom and has no extras. The qtek official rom is probably a safer install because its an official rom and many good reports of success and users pleased with the outcome.
Yes when you have flashed just input all those settings again.
Plus you can backup your voice tag database between hard resets by copying the file CommandModel1.bin found under the windows folder to your pc or to the memory card. After rom upgrade copy it back to your windows folder and all your voice tags are back!
Create backup of windows\start menu - most programs that are on the storage card dont need a reinstall.
Create copy of pim.vol in the root directory of the device - contains contact and appt information. After flash change the new pim.vol to pim.vo and copy and paste old pim.vol (use total commander or gsfinder file explorers for this) and soft reset and you will have info back.
Create backup of windows\favorites - for all your internet favorites.
That will make restore a bit quicker than otherwise.
Cheers for the info. I was actually thinking of trying the Mr. Clean one first, is there anything missing from this one, or is it just less stable?
Mr clean is just a clean rom without any of the manufacturers addons. It will probably run very well - its the flashing process with it that may not be as safe as an original rom and may possibly destroy your bootloader etc.. so you have a brick phone. I would always go for the safest option and would not suggest chopping and changing roms. Read the many users stories where everything goes wrong and the forum needs to help them out.
meschle said:
Mr clean is just a clean rom without any of the manufacturers addons. It will probably run very well - its the flashing process with it that may not be as safe as an original rom and may possibly destroy your bootloader etc.. so you have a brick phone. I would always go for the safest option and would not suggest chopping and changing roms. Read the many users stories where everything goes wrong and the forum needs to help them out.
Click to expand...
Click to collapse
True, I didn't think about that. Thanks again.
Ive been using Mr clean rom for 1 week now and its excellent from my experience. Its tottaly clean and runs so fast!
By clean i mean it has no customizations as you will find on official roms. It flashed just like any other rom too. Easy as pie. Just my info as people would like to know.
I've just upped to the QTEK ROM, and I've a couple of problems, nothing too serious though I don't think?
Firstly, when making my GRPS connection - I can't seem to find anywhere to input the WAP Proxy settings?
Edit, sorted this one now
Secondly, when settinp up my MMS - I can't select connect via Picture Message in the settings, it's not there?
I'm guessing this is some other connection I have to make up?
Any idea guys?
Scottland said:
I've just upped to the QTEK ROM, and I've a couple of problems, nothing too serious though I don't think?
Firstly, when making my GRPS connection - I can't seem to find anywhere to input the WAP Proxy settings?
Edit, sorted this one now
Secondly, when settinp up my MMS - I can't select connect via Picture Message in the settings, it's not there?
I'm guessing this is some other connection I have to make up?
Any idea guys?
Click to expand...
Click to collapse
I cant find what you say under settings - what does it do?
Never mind ignore me, that'll teach me not to read T-Mobile's site correctly

---Problem--- Official Cingular 8125 2.25 Update

I have never flashed this phone with any kind of alternate firmware, yet when I go to run the official one from HTC, I get this at 8-% exactly, on 2 diffrent phones:
_______________________________________________________________
ERROR [326]: INVALLID COMMAND
This NBF file cannot be used with for your PDA Phone. Please check you NBF file.
_______________________________________________________________
Then the phone turns into a brick. All it does is show the Tri-Color test looking screen untill try to flash again...
Any suggestions?
What phone do you have?
Whoops....
Sorry... I posted this in the wiz forum and didnt even think to put my phone model....
Cingular 8125
Thank you!
Re: Official Cingular 8125 2.25 Update ---Problem---
pittaman said:
I have never flashed this phone with any kind of alternate firmware, yet when I go to run the official one from HTC, I get this at 8-% exactly, on 2 diffrent phones:
_______________________________________________________________
ERROR [326]: INVALLID COMMAND
This NBF file cannot be used with for your PDA Phone. Please check you NBF file.
_______________________________________________________________
Then the phone turns into a brick. All it does is show the Tri-Color test looking screen untill try to flash again...
Any suggestions?
Click to expand...
Click to collapse
If you are attempting to flash the official ROM on an 8125 and getting this error, there's some bad juju goin on.
Just to be sure, you got the following ROM, correct?
http://www.htcamerica.net/support/software_downloads_8125.htm
I’ve downloaded that so many times my browser is upset at me. There must be a lot of bad JuJu... because It has tanked 2 different phones.....
I’ve taken your 2.3 update, and ran it... It went though... got to 98 and turned red on the phone... finally went to 100% and rebooted... but it was still at 1.8... but at least the phone works again... I really need the push e-mail though... and would prefer to use the official update... or a close derivative..
You should CID unlock first before you apply any ROM found in this forum.
If your phone is virgin, i.e. never been updated to a non official ROM, you will be fine going from 1.8 to this ROM and you would not need to CID unlock. I have gotten an nbf error before, but it was from an attempted downgrade to the stock 1.8 ROM from Summiter's 2.17 release.
Check your OS version and report back.
I know it says you have never upgraded before... If you're still having problems, just take it back to the store, we bricked a phone stuck on the 2.17 ROM and returned it with no problems. Apparently the 8125 does not like animated themes (not my idea, but it did have entertainment value).
Could there be something up with my PC if it bricked 2 seperate phones? WOuld it be possible to fix em with a diffrent PC? and do you think a Cingular store would update the firmware on the phone if it wasnt broken already?
pittaman said:
Could there be something up with my PC if it bricked 2 seperate phones? WOuld it be possible to fix em with a diffrent PC? and do you think a Cingular store would update the firmware on the phone if it wasnt broken already?
Click to expand...
Click to collapse
There's always the possibility of a virus causing issues, but it's exceedingly remote.
If the phone is working you should be able to bring it into any Cingular store and have them do the update for you.
pittaman said:
Could there be something up with my PC if it bricked 2 seperate phones? WOuld it be possible to fix em with a diffrent PC? and do you think a Cingular store would update the firmware on the phone if it wasnt broken already?
Click to expand...
Click to collapse
I concur with gamescan that it might be a virus, or some crappy spyware. I don't think however that you've "bricked" your phones as you WERE able to install sumitter's 2.23 OK. Of course since you didn't SID unlock you didn't get the full upgrade. I disagree with those who insist that you don't need to unlock. Mayhaps you don't need to but I know that sumitter and the other ROM gawds here have always suggested so. If I was you I'd downgrade to the 1.05, unlock, then upgrade. I'd also scan your PC with Spybot, maybe AdAware. Also I'd delete my temp files, in the c:\documents and settings\%username%\local settings\Temp. Also empty your temporary internet files. I've seen large temp folders on PC's create all kinds of grief. Just a suggestion.
Steven
chow
Well... I appriciate all your help thus far.
I called Cingular Yesterday ant they sent out 2 replacement phones for free, and I got them today... With the update already in place, so I dont think I'll be playing with unlocking again LOL... But this information is very helpful, as my Uncle has the same phone and needs the push email more than I do. If his phone gets toasted, Ill be here with the results...
Thank you all very much... this is my new favorite place!!!
Not A virus .... its the phone
Apparantly the newer phones have a new flash chipset G4 which is not compatable with the current crop of cooked roms on this site. I think summiter has one that will work but it didn't work for me. I returned my phone for a replacement hoping to get the g3 chipset but to no avail all the new ones are G4 and are unable to be flashed to the custom roms. also you should be able to sim unlock with no issues but to cid unlock you may need to look elsewhere
Re: Not A virus .... its the phone
alynch75 said:
Apparantly the newer phones have a new flash chipset G4 which is not compatable with the current crop of cooked roms on this site. I think summiter has one that will work but it didn't work for me. I returned my phone for a replacement hoping to get the g3 chipset but to no avail all the new ones are G4 and are unable to be flashed to the custom roms. also you should be able to sim unlock with no issues but to cid unlock you may need to look elsewhere
Click to expand...
Click to collapse
First, the OP was using the OFFICIAL CINGULAR UPDATE not a custom Rom.
Second, He was upgrading from 1.8 which is a 1.x Rom, this means his phone is indeed a G3 variant as the 1.x Roms only have G3 IPL/SPL.
I had this same experience from a virgin HTC 8125....
I had stop all apps running and recharge my battery. Then disable my sleep and screensaver then it worked.

downloaded orginal rom from www.htc.com

and still having problems.. at 95% is it says error. and says to check my nk.nbf file...... i have a g4, and i cant get ANY rom to work period. and its starting to piss me off
any anwsers?? on what i need 2 do?
I had the same problem with my G4 a while back. I wound up cooking my own ROM to fix it. You will need a ROM without the IPL/SPL in it. If it's not already dead, pull the battery. The bootloader screen will drain the battery relatively quickly, and the phone will not charge in that state.
downgrade to button's 1.xx ROM (on FTP here ftp://xda:[email protected]__RUU_Wizard_1050412_WWE_101_11210_WWE.exe) at least TRY a CID unlock using LokiWiz or aWizard and then flash back to original.
baarod said:
downgrade to button's 1.xx ROM (on FTP here ftp://xda:[email protected]__RUU_Wizard_1050412_WWE_101_11210_WWE.exe) at least TRY a CID unlock using LokiWiz or aWizard and then flash back to original.
Click to expand...
Click to collapse
its a G4.. it cant be unlocked
Try molski's rom. I have a G4 8125 and that is one of the few that would load correctly for me. Just make sure you get the version he made for g4 users. you will have to input your carrier specific stuff, like gprs, but it loads.
cptcafne said:
Try molski's rom. I have a G4 8125 and that is one of the few that would load correctly for me. Just make sure you get the version he made for g4 users. you will have to input your carrier specific stuff, like gprs, but it loads.
Click to expand...
Click to collapse
ive tired that rom.. and it will not work for me.. i dont know if its becuase i installed a different cooked rom first or what... but i install his 30mb G4 rom.. and i end up with red, blue and green screen after
I don't have his 30 meg free one, I have RUU_Molski.Biz_226102_22610105_022511_G4_WWE.exe loaded. so far it has worked fine, and that was after I had tried a few other cooked roms that did not installl correctly.
cptcafne said:
I don't have his 30 meg free one, I have RUU_Molski.Biz_226102_22610105_022511_G4_WWE.exe loaded. so far it has worked fine, and that was after I had tried a few other cooked roms that did not installl correctly.
Click to expand...
Click to collapse
hmmm, i have the same one.. but mine says 30mb... anywho... my batt is almost dead cuz i let it sit on the bootloader screen... so now i dunno wtf 2 do... i might just charge the battery on my friends 8125 and go from there
cptcafne said:
I don't have his 30 meg free one, I have RUU_Molski.Biz_226102_22610105_022511_G4_WWE.exe loaded. so far it has worked fine, and that was after I had tried a few other cooked roms that did not installl correctly.
Click to expand...
Click to collapse
did all of the xtra programs install??? like total commender and all that ****? or what.... i get confused with all thos .cabs and **** being inthe extended rom.. *shrugs*
it is a clean rom, more or less. You can either get it from the XDA ftp, or Molski web site, www.molski.biz. Yes, it is a slight pain to reinstall everything, but at least your phone will be up and running.
cptcafne said:
it is a clean rom, more or less. You can either get it from the XDA ftp, or Molski web site, www.molski.biz. Yes, it is a slight pain to reinstall everything, but at least your phone will be up and running.
Click to expand...
Click to collapse
clean rom means no extra programs installed right??? and molski took out all that other cingular **** i dont need.... and also.. i have cingular.. i know how ot set up the media net settings.. but as far as mms.. i dont know... also do you have AIM?
there is a cab you can install for the MMS, and I have aim, but not while I am at work. Which is where I am right now.

im looking for : CUSTOM__RUU_Wizard_1050412_WWE_

hi all
i tried to download the file ftp://xda:[email protected]__RUU_Wizard_1050412_WWE_101_11210_WWE.exe from the unlockung topic then it failed
seems to be removed
somebody have please upload it on any server except rapidshare
like : http://www.quicksharing.com/
or http://www.up4world.com/
my device now unusefull , so please help me
thanx in advanced
http://download.yousendit.com/FF900F2908E9D05B
Thanks for the info.
Hi there everyone
Greetings from Paris
I encountered the same problem. The file was not there anylonger. Then I saw this post, and its reply. I downloaded the file on http://download.yousendit.com/FF900F2908E9D05B which worked fine.
I ran the CUSTOM__RUU_Wizard_1050412_WWE_101_11210_WWE.exe file.
So far so good, and then the process crashed at 98%. Something about a file in outlook. I started the whole process again, and now it just stalls at 98%. No error message. NOthing. Anybody have any idea what I should do now...
I have an Orange SPV 3000. I can put the new rom back but I wanted to do a cid unlock, before doing so. It seems to be necessary to be able to try out different roms...
Thanks.
Paul Bourbon said:
I have an Orange SPV 3000. I can put the new rom back but I wanted to do a cid unlock, before doing so. It seems to be necessary to be able to try out different roms...
Thanks.
Click to expand...
Click to collapse
I never have to downgrade before I do the CID unlocked. I've tried with two MDA and never encountered any problem. You will only need to downgrade if you CANNOT CID unlocked; otherwise, don't bother to downgrade.
thats just the point. I cant do the cid unlock... And I suspect that the rom version has something to do with it. Anyway, thats what I read everywhere on this site. So I am still looking for a working link to Button 1.05 ?
Paul Bourbon said:
thats just the point. I cant do the cid unlock... And I suspect that the rom version has something to do with it. Anyway, thats what I read everywhere on this site. So I am still looking for a working link to Button 1.05 ?
Click to expand...
Click to collapse
When downgrading with this ROM...it will stall at 98% for a few minutes...be patient. To confirm that the ROM I posted was legit...I used it again myself and worked fine. Then to make sure it wasn't just me...I had 2 other people tell me they used it and worked fine for them as well.
Don't know what to tell you as this is the ROM that was hosted on the FTP site for a long time.
shell tool
If your having trouble flashing a rom the shell tool posted on the g4 threads lets you flash any rom you wish onto your phone i have a g4 cid locked and using the tool i can swap my roms every day if i wished to with no hassle
http://rapidshare.com/files/17787647/ShellTool_bugfixed.zip
Paul Bourbon said:
thats just the point. I cant do the cid unlock... And I suspect that the rom version has something to do with it. Anyway, thats what I read everywhere on this site. So I am still looking for a working link to Button 1.05 ?
Click to expand...
Click to collapse
Get yourself a signature. Is your Wizard G3 or G4.
I think that my wizard is a G3. I just added my signature.
Still looking for the mysterious file that apparently is no longer posted on this site.
thanks for any info.
i need a rapdishare or megauploads link to where i can download a 1.xx ROM for my G3 Qtek 9100 (Tmobile with imate 2.21 ROM).
I want to upgrade to wm6 and need to have a backup plan if it fails
10x in advance.
j3d1n4s7y said:
http://download.yousendit.com/FF900F2908E9D05B
Click to expand...
Click to collapse
thanx for uploading , but sorry this server blocked on our country
if any one can upload it again on the servers which i linked on the first post
thanx in advanced
looking for BUtton 1.05
this rom is not working for me. I stalls at about 98% of the process, and dies...
If you decide to do it, make sure you have a back up option.
Do a search on PirateBay for it. Its seeded...
i found the file
thanx for all
my device unlocked

Help! Unlocking? to upgrade to wm6

Hey guys.
i just wanner say first im a noob at phones so dont flame me.
Right, i got a brand new t-mobile compact 2 (htc charmer) with t-mobile rom on it. i really wanner upgrade to Windows mobile 6 so badly but i cannot flash my rom cus it aint unlocked.
So i tried doing it myself with the unlocker this website suggests, but that always fails .
What i think happend is this mda has been updated to the latest t-mobile rom. Which is:3.8.2.21 WWE and the unlocker is only for the old versions.
I actually dont know im right at all. but if anyone can get back to me either by pm, email or If you know your stuff please dont hesitate to add me on msn, and talk me though it. trust me its alot easier to do that then wait for thousens of emails.
Anyway any help will be amazing. remeber im a noob so please dont flame me, i just want to be able to experince the mobile 6 that all you guys are.
Email/MSN: [email protected]
Thankyou so much everyone. I hope you can solve this problem.
Oliver Pole
You don't have to unlock your phone to flash WM6. Considering you've already flashed the latest t-mob rom, just go to TouchFLO ver. 2.1 thread in Charmer Mobile 6, download the rom, read the instructions and flash. It will work.
Good luck.
Okiess gonner try it now. hopefully it will, will get back to you soon.
Ill describe the entire process.
Nope still not working, wont flash.
I run the flasher bat file the screen stays completely still nothing happens and i donno why. is it cus its not cid unlocked. i know you said it dont, but one of the guys said it did.
Get back to me soon
poleanator said:
Nope still not working, wont flash.
I run the flasher bat file the screen stays completely still nothing happens and i donno why. is it cus its not cid unlocked. i know you said it dont, but one of the guys said it did.
Get back to me soon
Click to expand...
Click to collapse
my charmer wasnt cid unlocked too, but i could install [vlodeck TouchFLO WM6 ver. 2.1]
it can be, that you have to install t-mobile AKU 3.3 from handy-faq.de

Categories

Resources