Related
hi all... i have upgrade mny O2 xda mini s with molski rom...after do it the phone start and ask me for alling the screen but during costuymization the phone power off and now it don't power on.... WHAT'S WRONG?????
ilmanu said:
hi all... i have upgrade mny O2 xda mini s with molski rom...after do it the phone start and ask me for alling the screen but during costuymization the phone power off and now it don't power on.... WHAT'S WRONG?????
Click to expand...
Click to collapse
I guess a battery problem, I read some comments in this forum about this, important is to use the original charger for charging.
i only use usb cable, now i have attach to 220v chargiing, but my battery work ok on another mini s...
ilmanu said:
i only use usb cable, now i have attach to 220v chargiing, but my battery work ok on another mini s...
Click to expand...
Click to collapse
Yes I know, it never happened to me, but it posted a lot of times. Just try it,it won't hurt the phone.
NOTHING... screen an charge led only flick (on-off very quickly) when with usb cable or charger connected i pull out the battery... if the phone dead during upgrade process i can undertand it...but that the phone dead during costumization process is....stupid...
ilmanu said:
NOTHING... screen an charge led only flick (on-off very quickly) when with usb cable or charger connected i pull out the battery... if the phone dead during upgrade process i can undertand it...but that the phone dead during costumization process is....stupid...
Click to expand...
Click to collapse
My guess is you flashed a G4 device (IPL/SPL 2.xx.0001) with a G3 Rom (IPL/SPL x.xx)!
That means your phone is dead!
You overwrited the G4 bootloaders with G3 bootloaders, there is NO WAY to get it back alive!
You had to read a lot more before trying to flash your device!
Molski
I was flashing my phone, and I fell asleep. When I woke up my screen was blank and it appeared as if my phone were off. I connected it to the power adapter and still no light no boot no nothing. I removed the battery and removed SD and SIM card, still nothing. I tried hard reset, stylus in the hole. Nothing. Can someone confirm that I am not the proud owner of a BRICK? Is there anything I can try beside throw it against the wall?
WayneC003 said:
Is there anything I can try beside throw it against the wall?
Click to expand...
Click to collapse
No need to throw it against the wall, why not consider to donate to XDA-developers
WayneC003 said:
I was flashing my phone, and I fell asleep. When I woke up my screen was blank and it appeared as if my phone were off. I connected it to the power adapter and still no light no boot no nothing. I removed the battery and removed SD and SIM card, still nothing. I tried hard reset, stylus in the hole. Nothing. Can someone confirm that I am not the proud owner of a BRICK? Is there anything I can try beside throw it against the wall?
Click to expand...
Click to collapse
It sounds to me that your battery just died while you were sleeping. You probably just received an error message and while connected to bootloader, it will not charge the device. If the phone is left in bootloader, it will eventually die.
Try using another battery or buying an external charger like a cradle with a dual battery slot and get it charged, put it in bootloader, flash it back to an official rom and then do some reading before trying again.
WayneC003 said:
I was flashing my phone, and I fell asleep. When I woke up my screen was blank and it appeared as if my phone were off. I connected it to the power adapter and still no light no boot no nothing. I removed the battery and removed SD and SIM card, still nothing. I tried hard reset, stylus in the hole. Nothing. Can someone confirm that I am not the proud owner of a BRICK? Is there anything I can try beside throw it against the wall?
Click to expand...
Click to collapse
I hope you did not have a G4 device and flashed a Rom with IPL/SPL included in it.which Rom was it,that you were flashing ?
zabardast_1 said:
I hope you did not have a G4 device and flashed a Rom with IPL/SPL included in it.which Rom was it,that you were flashing ?
Click to expand...
Click to collapse
I have G3 Wizard. I believe it had IPL/SPL included.
WayneC003 said:
I have G3 Wizard. I believe it had IPL/SPL included.
Click to expand...
Click to collapse
And I am assuming you had previously CID/SIM unlocked it??
If yes...find a way to charge your battery, re-connect it, then re-flash. I learned that even the really badly damaged wizards can usually be saved form the brickyard!
Yes If
it you do get a charge on your battery or have a new battery just flash another rom on it..its easy just follow the instructions from this furomhttp://forum.xda-developers.com/showthread.php?t=337907
it will show you how to get it into bootloader mode.....
I'm still a New to this but it might help you !!!!!
CK
WayneC003 said:
I have G3 Wizard. I believe it had IPL/SPL included.
Click to expand...
Click to collapse
Ok,if it's a G3 device,then there's nothing to worry,it sometimes happen due to a bad flash,or as you said cud be due to battery discharge during flashing or losing usb connectivity.Fully charge you battery by some means and check the USB connectivity.
Perform the procedure as posted my me in this thread,I hope it'll recover back to it's default status,
http://forum.xda-developers.com/showthread.php?t=337907
Good luck
WayneC003 said:
I was flashing my phone, and I fell asleep. When I woke up my screen was blank and it appeared as if my phone were off. I connected it to the power adapter and still no light no boot no nothing. I removed the battery and removed SD and SIM card, still nothing. I tried hard reset, stylus in the hole. Nothing. Can someone confirm that I am not the proud owner of a BRICK? Is there anything I can try beside throw it against the wall?
Click to expand...
Click to collapse
This may due to 2 reasons:
1.Your battery was die,try to charge it or change another one.
2.The chip which includs IPL is die,you may replace another chip or throw you phone out.
I was trying to update my WM5 to WM6 I have the G4 8125 , now it wont turn on I plugged it in to the charger port and the light that shows it's charging doesn’t even come on. Last night after I was trying to update it went completely blank, I tried to run the Official AT&T RUU_Wizard_225111_22511102_022511_CWS_WWE_Ship_1 and it wont even connect to my phone it gives me the connect error, every now and then last night it would show the boot loader screen but now its doing nothing someone HELP ME!!!!!!!!!!!! PLZZZ Does this mean my phone is bricked ???
Sounds like the battery is dead at a guess. As you have already seen the bootloader screen that is a good sign. You need to charge the battery away from the phone either in a cradle battery charger or another persons phone. If after charging the battery the phone is still dead I am afraid it maybe RIP.
I am sure others may help you far better than me though
Shew , i hope it is just the battery if its not the battery is thier anything else i can do for the phone ?
I am now in the same boat with my K JAM
What was you trying to do to your phone ? the same thing i was ?
emmanuel_harris32 said:
What was you trying to do to your phone ? the same thing i was ?
Click to expand...
Click to collapse
Basically but I have left the battery out for 30 mins and it has restarted
You can buy A charger which will charge the battery out of the phone on E bay
emmanuel_harris32 said:
I was trying to update my WM5 to WM6 I have the G4 8125 , now it wont turn on I plugged it in to the charger port and the light that shows it's charging doesn’t even come on. Last night after I was trying to update it went completely blank, I tried to run the Official AT&T RUU_Wizard_225111_22511102_022511_CWS_WWE_Ship_1 and it wont even connect to my phone it gives me the connect error, every now and then last night it would show the boot loader screen but now its doing nothing someone HELP ME!!!!!!!!!!!! PLZZZ Does this mean my phone is bricked ???
Click to expand...
Click to collapse
Most important is to get your battery fully charged atleast, I think it has gone flat,how are you trying to charge the battery ?,it won't get charged through usb cable, cuz usb cable will not charge in bootloaders,it got have a working OS on the phone and only provides 0.5 amp(500 amp power),where as now it'll only start charging if you connect it to a 'Wall Charger' which provides 1 Amp (1000 Amp power), or get a charged battery from a friend and check if your phone gets into bootloaders,if it gets than my friend your saved.WELL,IF NOT,.....I'm afraid you gotta shinny expensive paper weight on ya desk.
which Upgrade Rom were you trying to flash and as you have a G4 device,what method did you adopt to flash the Rom ? a G4 device can only be upgraded through SoftSPL or HardSPL method in case upgrading to a custom build wm6 Rom and or can only be flashed with an official Rom.
Secondly ,if you flashed a G3 specific Rom which includes IPL/SPL in it,will definitely "BRICK" the phone
I just wanted to thank everyone for your help , i got my new battery in yesterday and my phone booted up flashed back to at&t orginal rom. Thank So Much.....
I was flashing my phone repeatedly last night. I've read the forums and have done about 4 successful flashes already. The problem is, I've found a WM6 rom for the Wizard that I wanted better than the ROM already inside my phone, and I proceeded to flash it. But I left the computer and phone by itself so that I could rest a bit (I've spent hours in front of the computer flashing my phone), and fell asleep. When I woke up, I noticed that the flashing failed, and it was at the tri-color screen. Then, it died on me. No battery, obviously, being stuck at the tri-color screen the whole night. Now, it doesn't charge or turn on. I know I just need a battery to run the phone. But where I'm from, batteries for the Cingular 8125 are rare, and I'm one of the few that has an 8125.
I don't know anyone who has a battery for the 8125, and there's nowhere to buy from here. Any recommendations?
First of all be sure that you haven't flashed a G4 ROM in a G3 device (or vice-versa) which would have made it a brick.
In case you haven't screwed up the bootloaders then look for the battery jump start thread that teaches how to revive a dead battery
good luck
ianestradalives said:
I was flashing my phone repeatedly last night. I've read the forums and have done about 4 successful flashes already. The problem is, I've found a WM6 rom for the Wizard that I wanted better than the ROM already inside my phone, and I proceeded to flash it. But I left the computer and phone by itself so that I could rest a bit (I've spent hours in front of the computer flashing my phone), and fell asleep. When I woke up, I noticed that the flashing failed, and it was at the tri-color screen. Then, it died on me. No battery, obviously, being stuck at the tri-color screen the whole night. Now, it doesn't charge or turn on. I know I just need a battery to run the phone. But where I'm from, batteries for the Cingular 8125 are rare, and I'm one of the few that has an 8125.
I don't know anyone who has a battery for the 8125, and there's nowhere to buy from here. Any recommendations?
Click to expand...
Click to collapse
First os all your Wizard is not a brick. To revive your battery try using a wall charger to charge you battery, or you can leave it attahed to a wall charger for some time and it should start charging after 10-15 mins (becoz one i got a dead battery and did the same) Once the battery is revived then flash it to a Official ROM, afterwards any custom ROMs or what so ever. I hope i helped. TC
i've the same problem!!! i leave the phone attached the whole night to the charger...but it was in bootmode, so it doesn't charge!!! it hasn't the power to flash my phone...when it arrives to the 85% (when the phone write into the flash memory) it reboots.....what must i do? i tried to jump start...with a 12v adapter...but nothing....
It won't charge in Bootloaders,as it doesn't provide any charging circuit .The phone must have and boot up to a working OS (Windows) to start charging,only then it has a charging circuit.
Try to get a fully charged batter ,may be borrow it from a friend or try to charge your battery with friends phone,flash a rom and only it'll start to charge.
i know....but...i have not a friend with a ppc like mine!!!! and even if i'll buy a new battery....how can i charge it????? a friend of mine has a qtek 9000....but the battery is different from mine.......
F0ll3 said:
i know....but...i have not a friend with a ppc like mine!!!! and even if i'll buy a new battery....how can i charge it????? a friend of mine has a qtek 9000....but the battery is different from mine.......
Click to expand...
Click to collapse
No need to buy a battery i say you use a External Battery Charger. Because even buying it would be cheaper then the battery itself and would help you in future too. I hope i helped. TC
Thanks
xda2_haseeb said:
First os all your Wizard is not a brick. To revive your battery try using a wall charger to charge you battery, or you can leave it attahed to a wall charger for some time and it should start charging after 10-15 mins (becoz one i got a dead battery and did the same) Once the battery is revived then flash it to a Official ROM, afterwards any custom ROMs or what so ever. I hope i helped. TC
Click to expand...
Click to collapse
Thanks, dude. I never even tried charging it with the wall charger. There seems to be other people that have the same problem as I do. Now my phone is up at the tri-color screen, and I'm charging it, then Ill start flashing again. Thanks again!
No Problem but now remember if you find ppl with same problem (on the forum) dont forget to guide them to this Thread. And no need for the thanks. TC
zabardast_1 said:
It won't charge in Bootloaders,as it doesn't provide any charging circuit .The phone must have and boot up to a working OS (Windows) to start charging,only then it has a charging circuit.
Try to get a fully charged batter ,may be borrow it from a friend or try to charge your battery with friends phone,flash a rom and only it'll start to charge.
Click to expand...
Click to collapse
Thanks, dude. I never even tried charging it with the wall charger. There seems to be other people that have the same problem as I do. Now my phone is up at the tri-color screen, and I'm charging it, then Ill start flashing again. Thanks again!
Click to expand...
Click to collapse
@ianestradalives's as zabardast_1's has said, your phone WILL NOT CHARGE unless windows Boots. Either buy a new battery or find someone with the same phone or an Orbit(as they use the same battery) also if you buy a new battery it generally arrives with enough charge to use for flashing(It did for me anyway). The only other way to do it would be to buy a dock with a second battery charging slot. Using the wall charger wont do anything except stop it from restarting ,while its plugged in.
@XDA2_haseeb why point people who have the same problem to this thread, if the answer you have given is incorrect?
scousemartin said:
@ianestradalives's as zabardast_1's has said, your phone WILL NOT CHARGE unless windows Boots. Either buy a new battery or find someone with the same phone or an Orbit(as they use the same battery) also if you buy a new battery it generally arrives with enough charge to use for flashing(It did for me anyway). The only other way to do it would be to buy a dock with a second battery charging slot. Using the wall charger wont do anything except stop it from restarting ,while its plugged in.
@XDA2_haseeb why point people who have the same problem to this thread, if the answer you have given is incorrect?
Click to expand...
Click to collapse
Dude, sorry to disappoint you, but his advice was correct. My phone is now up and running, and it has NBD 9.2. The advice he has given is correct. It works.
Ok,was your phone in Bootloaders (muliticolor screen) or with a working OS installed on it when you charged with a wall charger ?
That's exactly what was i was about to ask Zabardast_1
As there is no way he could charge his phone while it is in bootloader mode. He either had battery power already in it and messed up the flash or you have just been lucky when you took the battery out of the unit and reinserted it and there was enough power left to flash
zabardast_1 said:
Ok,was your phone in Bootloaders (muliticolor screen) or with a working OS installed on it when you charged with a wall charger ?
Click to expand...
Click to collapse
In bootloader screen. If you were flashing a rom and it failed, you usually end up in the tri-color (aka "Bootloader") screen. Do what haseeb said (like I did) and plug your wizard to a wall charger and wait for a few minutes. When I plugged mine, it immediately lit up. Good hunting!
scousemartin said:
That's exactly what was i was about to ask Zabardast_1
As there is no way he could charge his phone while it is in bootloader mode. He either had battery power already in it and messed up the flash or you have just been lucky when you took the battery out of the unit and reinserted it and there was enough power left to flash
Click to expand...
Click to collapse
Nope. I'm sure the battery was drained. The other night, my phone was in the bootloader screen THE WHOLE NIGHT. And yesterday, I tried reflashing, but it won't start anymore because of - obviously - no battery power.
IF you don't believe me, fail a flash and drain the battery. Then plug it into the wall. It really works.
scousemartin
YUP! thats very true.
The question here is 'How did he charge in Bootloaders with a wall charger',it has to have a working OS on it to start the charging circuit,which isn't present while in Bootloaders.
Flashing is a separate issue.
it will light up as it has power but it WONT CHARGE IT. You were LUCKY that's all and you had power in your battery. You just never realised it. If you want to prove us wrong let the battery go low and then try your revival attempt again. I guarantee you will be buying another battery or charging it somewhere else
also i have been through this personally with my xda mini-s and the only remedy was to buy another battery (or recharge it). You could leave your phone connected to the wall charger for a week and it wont make a blind bit of difference to the battery level. I know because i tried.
Anyway glad you got it sorted ,but the solution to your problem was not charging the phone. Thats all i have to say on this matter now
scousemartin said:
also i have been through this personally with my xda mini-s and the only remedy was to buy another battery (or recharge it). You could leave your phone connected to the wall charger for a week and it wont make a blind bit of difference to the battery level. I know because i tried.
Anyway glad you got it sorted ,but the solution to your problem was not charging the phone. Thats all i have to say on this matter now
Click to expand...
Click to collapse
It did get sorted. But I am really sure about the battery thing. I guess this is an anomaly. Besides, the XDA is different from a Wizard.
lol the xda mini-s is exactly the same device a 8125 is, they re both wizards
hey guys, i was uploading wm5 back to my 9100, when at 90% it restarted, and in the installation it was showing me that my battery is empty, so i took out the battery, and placed it back and tried to put it in bootloader, but there was no hope, so i connected it to the charger, it was charging through the night and once or twice it turned on for 10sec`s ( itself) in bootloader...and now i took the phone off the charger and it has no sign of life, im trying to put it somehow in bootloader, but its not working...it looks like he`s dead...is there anyway that i can put it in bootloader!?!??thanks in advance!!!and even if i put it on USB through the computer it is not showing that its charging, and the same thing is happening when i put it on the charger, the orange light is not on...
Which is your device,G3 or G4 ?.If its a G3,the battery is dead and it won't charge in Bootloaders,It'll only charge with a wall charger,capable of 1amp out put or you may have to 'Jump Start' it and then it'll start to charge.
But,if its a G4 and if you had applied HardSPL to upgrade to wm6,it was essential to remove HardSPL and revert back to original official IPL/SPL and then reflash the wm5,otherwise the phone will be 'Bricked'
thanks for replying on my post,
i think that my my device is G4, probably, because the wm5 that i was installing it was Wizard_Love_2.26.10.2_WWE_Novii_CF2 for G4...
anyway how can i 'Jump start' my device?
thanks in advance