Hello! I talked to xplode about this and he had no clue what could it be...
soul_train said:
...When I run Device Software Update Utility I go to next. It finishes with updating info I go to next. And then it says "This ROM update does not design for your device, please get a proper ROM upgrade and thry again...
Click to expand...
Click to collapse
-------------
xplode said:
Strange, works fine here, try to repeat the procedure afterall you upgrade with noid, it is not likely to get error like this
Click to expand...
Click to collapse
Don't know where is the problem. I have Helmis 1.4 3.5AKU... I have thryed both new WM-s and On both I get the same problem. So if anyone knows help would be appreciated. Thanks!
Soul Train
I got the same error message. I tried to change operater, but that didn't do the trick, so I'm still on the case
Edit: I'm normaly using Windows Vista, but I still have my XP installation, so I tried to boot in XP an run the upgrade from there. This worked fine, so mayby it's a problem with Vista althroug it should work. So my best advice is to try reboot you system, i know it's not alot of people who runs dual boot systems as standart
hagsted said:
I got the same error message. I tried to change operater, but that didn't do the trick, so I'm still on the case
Click to expand...
Click to collapse
What WM do you have? Shoud I try to Revert back to Wm2003 and try like that?
I upgraded from Helmi's Aku 3.2 to Xplore's 3.5 R4. If you have the posibility, try to connect your BA to anothor PC and run the update from there, I think it's a problem caused by Windows on the specific pc.
Related
ok...so i got a windows vista update utility for the HTC wizard ,but now i need help to modefy the utility to work with custom roms....we need to remove the contry id check.etc.....if you know how to do it please contact-me.
temp made stiky.as this will benefit everyone
Version
Is it version 2.6?
robjae said:
Is it version 2.6?
Click to expand...
Click to collapse
no......... but it works with vista with the original rom.
Tmo
There is a 2.6 on the T-Mobile site for the MDA.
faria said:
ok...so i got a windows vista update utility for the HTC wizard ,but now i need help to modefy the utility to work with custom roms....we need to remove the contry id check.etc.....if you know how to do it please contact-me.
temp made stiky.as this will benefit everyone
Click to expand...
Click to collapse
Faria, I dont know how to remove the coutry id check but will be great if you upload it to the ftp for those that have problems(like me) using old ruu in vista.
Thanks.
XP OS & Vista OS
I have not been successful in getting this to work in Vista OS, so I just created a partition and installed XP as second OS. Hey, it works until bugs worked out of Vista.
XP OS & Vista OS
I have not been successful in getting this to work in Vista OS, so I just created a partition and installed XP as second OS. Hey, it works until bugs worked out of Vista.
Hi Faria!
Just to let you know that I've just contacted the guys at I-mate regarding this problem and they said there's already one version coming soon.
Hope it does not take so long!
Regards,
RUU from Cingular
I can flash my phone with Vista, with the offical Cingular 2.25 (which uses RUU 2.5.2) ROM. When I replace the nk.nbf, it can't open the file. Maybe this helps. If anyone knows what the RUU looks for in the rom file, maybe we could fix it.
Did you tried tools than enable all buttons of an application ? (I've done than quite a long time ago and it worked) ?
EDIT : have a look at http://www.angelfire.com/falcon/speedload/Enabler.htm
any luck on this?
faria said:
ok...so i got a windows vista update utility for the HTC wizard ,but now i need help to modefy the utility to work with custom roms....we need to remove the contry id check.etc.....if you know how to do it please contact-me.
temp made stiky.as this will benefit everyone
Click to expand...
Click to collapse
could u please give me the vista update utility?
OK, so, here it is.
Download, extract, Donate!
your device *MUST MUST MUST* be synced with ACTIVESYNC and in WINDOWS MOBILE before starting the procedure.
All of you kind folks who pledged to the fund... please feel free to use my donate link </shameless_whore>
Cheers!
Olipro.
Hey Olipro
Nice to see this is up and running.
One Question....does it need to be in XP or can it be done in Vista as well?
try Vista and report back.
Vista worked for me
Vista worked for me
goes through alright (once drives are fixed up) however flashing any other rom still fails - even when manually going into the hard spl, and then running flash utility, it says the rom is corrupt.
Just the start?
ajajaj said:
Vista worked for me
goes through alright (once drives are fixed up) however flashing any other rom still fails - even when manually going into the hard spl, and then running flash utility, it says the rom is corrupt.
Click to expand...
Click to collapse
I guess that this means we need to now roll our own, or wait for someone to release a p3600i rom which uses this spl?
ajajaj said:
I guess that this means we need to now roll our own, or wait for someone to release a p3600i rom which uses this spl?
Click to expand...
Click to collapse
Did you try flashing a new radio ROM as well. Previously we could not flash anything other than the HTC Official ROMs including radios.
Radio Upgrade successfull
Andyc46 said:
Did you try flashing a new radio ROM as well. Previously we could not flash anything other than the HTC Official ROMs including radios.
Click to expand...
Click to collapse
I just upgraded my Australian P3600i to Radio 1.50.08.11 successfully! WOOT!
Now all I need is a workable p3600i WM6.1 rom.....
ajajaj said:
I just upgraded my Australian P3600i to Radio 1.50.08.11 successfully! WOOT!
Now all I need is a workable p3600i WM6.1 rom.....
Click to expand...
Click to collapse
I have an nbh from an existing rom, I want to change the 400 to 401 as referred to in other thread - can anyone offer context (where do i find the 400 specifically referred to?)
if I search, is it hex I am searching for, or ascii?
TIA
ajajaj said:
I just upgraded my Australian P3600i to Radio 1.50.08.11 successfully! WOOT!
Now all I need is a workable p3600i WM6.1 rom.....
Click to expand...
Click to collapse
Well that is a good start.....which ROM did you try that came back as corrupt?
Andyc46 said:
Well that is a good start.....which ROM did you try that came back as corrupt?
Click to expand...
Click to collapse
I have tried the Trinity_WM6.1.Black_Edition.OS_Version_CE_5.2.19701_Build_19701.1.0.2_by_Akeo rom - this reports as corrupt.
Also, RUU_TRINITY_WM6.1_WWE_ASIA_3.12.YK.Lite - this one complains that the rom is for 128, not 256 MB.
等待中国高手的简体ROM
waiting 4 the writer 's CHS ROM
experiments in flashing
I modified the first instance i could find of 0x0400 the RUU_TRINITY_WM6.1_WWE_ASIA_3.12.YK.Lite rom to 0x0401 and got a different error message saying:
Error [226] : FLASH WRITE
Flash write error happened. please check your PDA phone.
now the phone is now stuck in SPL
changed it back, and re-flashed, flash failed with "type error (128 vs 256)" however the phone now boots again.
tonychou said:
等待中国高手的简体ROM
waiting 4 the writer 's CHS ROM
Click to expand...
Click to collapse
No good to me...I am after WWE
ajajaj said:
I have tried the Trinity_WM6.1.Black_Edition.OS_Version_CE_5.2.19701_Build_19701.1.0.2_by_Akeo rom - this reports as corrupt.
Also, RUU_TRINITY_WM6.1_WWE_ASIA_3.12.YK.Lite - this one complains that the rom is for 128, not 256 MB.
Click to expand...
Click to collapse
That seems strange as the basic ROM for D810 (Standard Trinity) is the same for P3600i.....you would think both phones should accept cooked ROMs (now we have Hard SPL).
sigh. problem is that none of the roms I try will load...
By changing first 0x0400 in mary nbh to 0x0401, it flashes as far as 11% and fails with communication error, then when booting changes the inital start screen of the phone, (flashed to phone) but no further. saying the rom is corrupt.
SUCCESS
fully flashed the P3600i to WM6.1 - writing new thread to show how.
I had tried a few times one 2 mechine
one on winxp and one on win2k3
but both mechine show the same error when i do the step 1
the phone go to 3 color but in pc side it shows the ERROR [260] message
don't know how to do ><
after reset the phone
nothing happened
What happened to me exactly the same as you!
money donated!
Thanks both olipro & ajajaj!
ok so i tried to do hard-spl. but i got a 260 error.. reset my phone, windows came back up.
this was from a xp sp2 machine :/
the crap thing is now i cant run any cab files on the wm device.. i've definately done something to do.
Hi. I already did a search for this but didn't find any help for a Herald.
I tried updating to 6.1 and it would not work. It would start to install but then crash and start over again. I probably tried 20 times and it would not work...not my phone is stuck on this screen with Red, Green, Blue and White stripes. Is my phone dead? Is there any hope? Thanks in advance!
This question is asked at least one or 5 times a week. Please search.
If your SPL still says 4.0.0.0, just flash another ROM. Assuming you have HardSPL setup or you were using USPL.
If your SPL says 1.0.0.0, then follow this.
Sorry like I already mentioned in my post I could not find a thread specifically for the Herald so I made a post.
My screen says IPL 4.26.0002 and then SPL 4.26.0000.
galva said:
Sorry like I already mentioned in my post I could not find a thread specifically for the Herald so I made a post.
My screen says IPL 4.26.0002 and then SPL 4.26.0000.
Click to expand...
Click to collapse
There's a million threads on this for the Herald.
Anyhoo, have you tried just reflashing back to the stock ROM or another ROM?
Tell me exactly what you did to flash.
Went to T-Mobile site. Typed in my phone's info and downloaded the 6.1 update for Windows Mobile...followed the instructions to install. It would start installing and then stop or crash I can't remember exactly. But I tried many times. I called T-Mobile and they said I had to get a new phone. I've never flashed my phone or anything like that...I had Spb installed on it and that was it...
Well I took out my ol Wing and tried to do the update once again to remember what error I keep getting.
The update starts to install on my Wing as the bar loading bar starts to fill it stops and then tells me an error has occurred.
ERROR [262]: UPDATE ERROR
Some type of communication error. But I can recover. So I do and then I try again. I've done this like 20 times before. I don't know if that helps any but thats my problem...
First, find hardspl and flash then flash rom
galva said:
Well I took out my ol Wing and tried to do the update once again to remember what error I keep getting.
The update starts to install on my Wing as the bar loading bar starts to fill it stops and then tells me an error has occurred.
ERROR [262]: UPDATE ERROR
Some type of communication error. But I can recover. So I do and then I try again. I've done this like 20 times before. I don't know if that helps any but thats my problem...
Click to expand...
Click to collapse
Sounds like there's a problem with your computer talking to the phone. Try taking tmobile's ROM, take out the NBH, rename it to HERAIMG.nbh and place it into your SD card (formatted to FAT32.) Then turn on your phone while holding the camera button.
galva said:
Went to T-Mobile site. Typed in my phone's info and downloaded the 6.1 update for Windows Mobile...followed the instructions to install. It would start installing and then stop or crash I can't remember exactly. But I tried many times. I called T-Mobile and they said I had to get a new phone. I've never flashed my phone or anything like that...I had Spb installed on it and that was it...
Click to expand...
Click to collapse
Tmobile has a 6.1 update?
galva, which windows do you use? XP or Vista?
igord said:
galva, which windows do you use? XP or Vista?
Click to expand...
Click to collapse
Wow guys thanks...I'll give these a try. I am using BootCamp to read my phone.
ivanmmj, do I need format the card using another phone or can I use a card reader. I don't have another phone I could use.
galva said:
Wow guys thanks...I'll give these a try. I am using BootCamp to read my phone.
ivanmmj, do I need format the card using another phone or can I use a card reader. I don't have another phone I could use.
Click to expand...
Click to collapse
You can use a card reader.
Smoke362 said:
Tmobile has a 6.1 update?
Click to expand...
Click to collapse
No. It's a 6.0 update.
I was updating from 6.0 to 6.1 and I am running XP in Bootcamp.
ivanmmj said:
Sounds like there's a problem with your computer talking to the phone. Try taking tmobile's ROM, take out the NBH, rename it to HERAIMG.nbh and place it into your SD card (formatted to FAT32.) Then turn on your phone while holding the camera button.
Click to expand...
Click to collapse
Wait...so I'm a noob...T-Mobile's ROM? Where do I get that? Do you mean the update file that I downloaded from T-Mobile? Thanks again!!! I hope this works! And will MS-DOS FAT work when I format the card? I am using Mac's Disk Utility and I don't get a FAT32 option.
Well I think I have the ROM actually. It's an EXE file so I'm not sure how I can go into it and rename a file inside of it. Sorry...my noob is showing huh? Here's what I downloaded awhile back that I think is the original ROM you are talking about.
RUU_Atlas_TMO_US_4[1].10.531.3_4.1.13.37_02.83.90_Ship.exe
IT WORKED! Thanks!!!!
galva said:
IT WORKED! Thanks!!!!
Click to expand...
Click to collapse
No problem. ^_^ Glad to hear that it worked. Were you able to flash it through a FAT format? Or were you able to format it to FAT32?
Hi,
I am trying to downgrade my Pda2k from WM6.1 to WM2003 but after running the "MaUpgradeUt_noID.exe" I don't get the current version not even the version that I am switching to.
I removed the cradle, before doing so ended the process of "wcesscom" and "rapigmngr", and put my device on bootloader mode. The I plugged it back and "USB" appeared on the screen and below is "v2.07". Still it does not work.
I am using the correct "MaUpgradeUt_noID.exe" and also the right "nk.nbf".
I have downgraded before but I don't know why its not working now.
hi and welcome to the forum. the only real problem is, that the version is not showing up on the 2nd screen of the RUU. the version that is currently on the device is not necessary.
that can have so many reasons, first you should try to follow the instructions in my tutorial word by word and if that does not help, post the log of the upgrader, maybe the CRC of the rom is not correct. that seems to happen a lot lately.
progammer said:
Hi,
I am trying to downgrade my Pda2k from WM6.1 to WM2003 but after running the "MaUpgradeUt_noID.exe" I don't get the current version not even the version that I am switching to.
I removed the cradle, before doing so ended the process of "wcesscom" and "rapigmngr", and put my device on bootloader mode. The I plugged it back and "USB" appeared on the screen and below is "v2.07". Still it does not work.
I am using the correct "MaUpgradeUt_noID.exe" and also the right "nk.nbf".
I have downgraded before but I don't know why its not working now.
Click to expand...
Click to collapse
It could be that the nbf doesn't like the RUU. Why don't you try flashing to a stock rom?
Chef_Tony said:
hi and welcome to the forum. the only real problem is, that the version is not showing up on the 2nd screen of the RUU. the version that is currently on the device is not necessary.
that can have so many reasons, first you should try to follow the instructions in my tutorial word by word and if that does not help, post the log of the upgrader, maybe the CRC of the rom is not correct. that seems to happen a lot lately.
Click to expand...
Click to collapse
i followed your steps throughly all the time. where can i find the log?
egzthunder1 said:
It could be that the nbf doesn't like the RUU. Why don't you try flashing to a stock rom?
Click to expand...
Click to collapse
i have windows mobile 6.1 installed
i want to downgrade it to 2003SE inorder to install WM6.5.5
its original windows was 2003SE
if there is another way of returning back to the old windows then let me know else you can help me with the question that i have asked from chief
05/06/2010 10:44:07.906 **************** Logging Started ****************
05/06/2010 10:44:07.906 Process L:\A Siar\A Siar\PDA 2K\BA_WM5_Downgrade_pack\BA WM5 Downgrade pack\Downgrade to WM2003SE\MaUpgradeUt_noID.exe p(1776)
05/06/2010 10:44:12.109 p(796) t(232) TraceToFile -> ERROR in CRAPIListener::AcceptConnection : hr = 0x8007274a - rapiconnection.cpp(268)
05/06/2010 10:44:12.109 p(796) t(232) TraceToFile -> ERROR in CRAPIDesktopPrivate::ReceiveConnection : hr = 0x8007274a - RAPIDesktopPriv.cpp(372)
05/06/2010 10:44:12.109 p(796) t(232) TraceToFile -> ERROR in ServerThread : hr = 0x8007274a - rapimgr.cpp(493)
05/06/2010 10:44:21.437 **************** Logging Stopped ****************
Click to expand...
Click to collapse
This is the log that I got from "C:\DOCUME~1\Home\LOCALS~1/Temp/WCESLog.log" file of my windows
It worked!
How?
In the wiki its said to also kill the "rapimgr" but if you kill that it will not work so only kill "wcescomm.exe" and "WCESmgr.exe".
Then I tried to upgrade it to 6.5.3 but again found the same problem, here is how to overcome that one too.
Its mentioned in the post of "Chef_Tony" to disable the USB connection but after doing so it didn't work cuz I got error from windows that "USB device couldn't be recognized" so I think because of this the rom version while upgrading didn't appear. However, again from ActiveSync I enabled the USB connection and it worked.
Thanks Chef_Tony and egzthunder1.
actually, for an upgrade from wm6.1 to wm6.5.3, a downgrade to wm2003 would not have been necessary. you'd only ever have to upgrade again, if your storage capacity is 43mb instead of 60mb. you can up- or downgrade between different cooked roms directly.
but since you made it work, it's ok, just as a time saver for next time
Thanks for the tip!
While I am glad it worked out, the solution doesn't make much sense...
meh...
Hi all
I really need some help please!!
I think I have read and searched and tried steps by step all the posts and threads on this, none of them work for me,
Ive flashed my HD2 & TD2 with HSPL, radios and roms many times in the past. I have a stock rom on my TD2, (havent flashed a cooked one yet but did on my HD2 and worked great),
the problem is when I try flash anything, (HSPL,Radio's and Roms)
I connect with WMDC on windows ultimate 64x and go through all the steps, the phone disconnects from WMDC when loading the tri-color screen, and installs the HTC sync drivers fine, and then (my problem) it hangs on 0%. this happens regardless of what I'm flashing after a while brings up the communication errors 208 & 260. this doesnt have any effect on the software HSPL or radio as a soft reset returns back to the homescreen just fine. I am running HSPL 1.8.3. , radio 4.49.25.17 and a shiped stock wm 6.5.
This is what Ive tried so far:
I have used 3 different micro USB cables,
updated my .net fx to 4.1
I have tried different Ruu's such as custom Ruu, Ruu from topaz, Ruu, supplied with Hspl, flashes center and KaiserCustomRUU.exe and a few others.
Ive tried the white screen fix many times. including the SDA unlocker and stuff.
I ve tried manual and automatic.
tried entering the the Tri-color screen manually and via the Ruu.
I tried different computers and different operating systems (W7ultimate and XP 32Bit and 64Bit)
tried active sync WMDC 6.0 and 6.1
Ive removed the SD card and sim and have tried flight mode
Restarted pc's mobile any reinstalled WMDC many times.
Ive tried renaming to the HSPL, radio and Rom to TOPAIMG.nbh , put 1 by 1 on formated fat32 SD card, run from Tri-color menu. all of them just hang on
loading....
Have tried mixing and matching Ruu's with HSPL's, Roms And radios and everything else i can think of, after 18 hours of this I am fed up and decided i need some help
Thanx in advance
can some1 please help on this?
ok
i have now download the official RUU_Topaz_S2_HTC_WWE-AFK_2.53.421.3_Radio_Signed_Topaz_61.44etc.25.35_4.49.25.91_Ship.exe Rom
and it worked with no problems.
it updated my HSPL from 1.83 to 2.51 and radio version to 4.49.25.91 which was exactly what i was going for.
The problem now is that i still cant change my HSPL, RADIO or flash a custom Rom which is what I need. it hangs on 0% and now gives me a 262 error which states that:
ERROR [262] : UPDATE ERROR
This error occurs during the CE ROM code upgrade process. If this happens, you can just soft reset the device and run RUU again. The update process will then continue. At this stage the rom on the device is incomplete and it will not boot back up into Windows. You will need to place it into the bootloader to continue.
which is not true as if a reboot it doesn't continue the update and just returns to the home screen as normal
help?
Now as your device is updated (officially)... so now can you try installing HSPL from here: http://forum.xda-developers.com/showthread.php?t=520312
Thanks.
prabhat said:
Now as your device is updated (officially)... so now can you try installing HSPL from here: http://forum.xda-developers.com/showthread.php?t=520312
Thanks.
Click to expand...
Click to collapse
Yes thanx i have. it was the first think i tried after i flashed the official HSPL, still doesnt work
IcedXian said:
Yes thanx i have. it was the first think i tried after i flashed the official HSPL, still doesnt work
Click to expand...
Click to collapse
Does your device is CID/SIM Locked? If yes you may have to try this first:
Diamond 2 CID/Security/SIM Unlocker. And then HSPL.
prabhat said:
Does your device is CID/SIM Locked? If yes you may have to try this first:
Diamond 2 CID/Security/SIM Unlocker. And then HSPL.
Click to expand...
Click to collapse
how do i check if it is locked?
IcedXian said:
how do i check if it is locked?
Click to expand...
Click to collapse
Try other network SIM and see if that is working?
prabhat said:
Try other network SIM and see if that is working?
Click to expand...
Click to collapse
Than x alot for your help dude!
just got it right now, didnt have internet so i coudnt make use of the automatic flash with Topaz-HardSPL_V5_09R6.
this error occured when using the manual. i got internet now and used the automatic flash and it worked like a charm.
thanx again will be in contact if i have any other problems
so how do i marked this thread as solved????
OK Good Cheers!!!
Now enjoy any ROM you want and have fun .
You can append the post title with "[SOLVED]".
Thanks.
IcedXian said:
Than x alot for your help dude!
just got it right now, didnt have internet so i coudnt make use of the automatic flash with Topaz-HardSPL_V5_09R6.
this error occured when using the manual. i got internet now and used the automatic flash and it worked like a charm.
thanx again will be in contact if i have any other problems
Click to expand...
Click to collapse
Brother explain more, how you solved your problem... I am also facing problem my room update also stuck at 0%..... what do you mean by "get internet"? and why you need it? and on which you get it mobile or pc?.......