I, have Siemens SX66 GSM ( PH20B) Upgraded to wron version and now it boot with colored horizontel straps (red,green,blue,white) and goes to WM 5, with slow to none functions and also lost radio.
Now I, tried with several WM5 versions and it display error message ( Model ID error 100) Can some one help how to remove / clean it and recomend working WM5.
See some post at the bottom of this topic
If you you have lost the Radio, ie, no version number is displayed on cold booting/hard re-set, then all is lost.
As i had the same problem with a phone I was given to fix.
As most/all of the Upgrade programs Check to see what Radio version the phone already has, and if it cant see one it fails
My only course of action was to get the Phone fixed under warenty
Read all about it here
Hope.......
Mine did the same thing, it was sooooo slow that I was thinking about buying a new unit but at the last breath I did the following and it worked:
- Go to the BootLoader screen (Press: Power Switch+Media Player+Recorder+Rest) all at the same time, your PDA should say “Serial” at the top of the screen.
- Plug you PDA to the cradle and it should read “USB” at the top of the screen.
- Use At least TuMa 1.3 with Radio 1.13.
Note:
The upgrade EXE should load up with a picture of the PD at the left side of the screen that DOES NOT look like your SX66…it looks like an HP PDA…!!!
Mine came back to life but sometimes you might have to SOFT reboot your PDA to get the Radio to work (Hard boot then use a third party software to softreboot).
Good luck.
so using the MaUpgradeUt_noID.ZIP and radio rom only you were unsuccessful at flashing?
Black6spdZ said:
so using the MaUpgradeUt_noID.ZIP and radio rom only you were unsuccessful at flashing?
Click to expand...
Click to collapse
I, went through all upgrades without issue but now PDA is so slow it takes ages to change selections..
have you downgraded back to 03se and still have this issue?
You will have to follow the steps very accurately...if you leave any step out you might end up like me at the beginning when my device was sooooo slow it was useless.
I took these steps from this forum...try it
Best Luck…
Thanks for all help did every thing but still some of menu are so slow that take several minutes to open , still looking for some tips and suggestions or if some one one knows how to turn it back to W2003
I, remoed some of programs from my SX66 that seems to be causing problems and were npt compatible with and got my PDA back...its now working awsome...Thanks for all who helped
Howdy, i have looked at all the guides, done loads of research into upgrading my Ignito.
I have tried to use the Olinex 1.40 and also the signed version....
But when i load it all up, go through the correct steps etc.. My phone screen looks like its just had some dodgy virus and looks like its about to die and then slowly turns off...
It then does a full reboot and its like i have a brand new phone again...
I am at a loss as to why it does this..
Anyone have any tips or tricks as to how to get around this problem ?
Any help at all will be very very welcome
Cheers
Sam
when you do the hard spl, you will only get a black screen and then it will reboot, just as you describe.
Hold the volume down key and then soft reset, if you see OLI anywhere, then it worked.
The problem is when i try the upgrade the screen seems to die aftera bout 10secs and then it says its fully done.
So there isnt enough time for the Hard SPL to be upgraded....
Anyone ?? Please....
The problem is when i try the upgrade the screen seems to die aftera bout 10secs and then it says its fully done.
So there isnt enough time for the Hard SPL to be upgraded....
Anyone ?? Please....
Click to expand...
Click to collapse
Maybe you could give more detailed information, what exactly are you doing, what does the PC end of the process say etc.
Can you take any screenshots, what SPL do you have now - the guide suggests that 1.93 could be better for you than 1.4?
Kim
It says complete after about 10seconds and then the phone reboots fully.
The current one i believe is 1.93.....
I have tried both of the Olinex versions to no avail at all.....
......
MuDvAyNeX said:
......
Click to expand...
Click to collapse
I guess no one is helping because you're not giving us enough information, procedure, XP or Vista, have you tried Hard-SPL 1.93, screenshots or better description of the problem.
Screen goes funny and then reboots just isn't enough
Kim
Well i have tried both of the Olinex versions both the 1.4 and the 1.93.
I am using windows vista and the mobile device center, its fully connected as i do a sync etc before hand.
I then load the Romloader that does the usual tick this, tick that etc.
Once that has happened i click the upgrade button, it then confirms i am going from the current SPL do the one i have chosen.
I click ok and then it goes to the progress section where it says it could take upto 10min, the screen on the phone then looks like it has got a virus and starts to look like its dying.
Meanwhile after about 10 seconds it tells me that upgrade is done, this is while the phone reboots and starts like its a brand new phone again with no changes that i can see...
In all honesty i can't see what i am doing wrong
Scrath what i just put, as i was typing that i was trying the upgrade via my mates XP laptop and it now says in the bootloader 1.93 Olinex...
I am going to guess this is upgraded... lol
MuDvAyNeX said:
it now says in the bootloader 1.93 Olinex...
I am going to guess this is upgraded... lol
Click to expand...
Click to collapse
Great, glad it's sorted, I was gonna say I don't have much experience with Vista (an' I don't want to )
I'm sure that I've read that there can be issues with the Vista device center(sic), A quick search of XDA-Dev will help.
If you want to eliminate the PC <-> Ignito pitfalls maybe try Suillers method of upgrading direct from the device Internal Storage.
Kim
i had duttys v2 cube on my tilt and one day i turned it off and i could not turn it back on. i thought it was the battery but i went to the att store and they said it still would not turn on and it was probally the phone. i couldn't do the warranty till i put the att rom back on but i could not turn on the phone. i didn't read enough and i went and used frankenkaiser, but i have gone pasted the "task 2a". but i have tried to just flash my phone but i my computer sees a device but not as a phone per say. but the rom flashing and activesync don't see it at all. but if i press send +power i get a green light and went i hit camera+power+reset i get a green light. but when i plug it in to charge i don't get a yellow light. i hope i have gave enough details. any...any help will be appreciated.
mike
First off you probably got alot of reading to do. But that being said Ive never bricked my phone yet so it is a topic which I have needed to look into just in case. So first off what all did you due to the phone prior to it being bricked, Ill read to try and help you but you read as well, because like I said I have not yet had a prob like this.
That really sounds like a hardware problem. I dont think a ROM could do that. If it wont even get to the bootloader send it in. They wont be able to tell it has a custom ROM if it wont even turn on. Hardware problem = warranty repair.
thanks to both of you for offering help. Jkingdev i think i will try that. the att store did say it might be the phone after trying the battery. i appericate everything.
ynottry13 i have flashed my tilt severly times...i did read somewhere that someone was wondering how many times can you flash i tilt till it dies. well i don't know if the two have anything to do with the other, i i would say about 10 or so. other than that i have not done anything else.
mad9791 said:
ynottry13 i have flashed my tilt severly times...i did read somewhere that someone was wondering how many times can you flash i tilt till it dies. well i don't know if the two have anything to do with the other, i i would say about 10 or so. other than that i have not done anything else.
Click to expand...
Click to collapse
10? seriously? It must be a MUCH higher number than that. Ive flashed well over 300 times..... from SPL's to ROMS to RADIOS to Bootsplashes. Still 0 issues as of yet
It is much higher than 10, I'm on version 15 of my personal cooked ROM, and had tried at least 10 different ROMs from other cooks prior to than. So between ROMS, radios, flash screens etc I've prolly reflashed mine over 50 times since July.
mad9791 said:
ynottry13 i have flashed my tilt severly times...i did read somewhere that someone was wondering how many times can you flash i tilt till it dies. well i don't know if the two have anything to do with the other, i i would say about 10 or so. other than that i have not done anything else.
Click to expand...
Click to collapse
Flash memory is good for thousands of erase/write cycles. Its not like the old "burning" of ROM chips. This memory is made to be rewritten. It is the same kind of memory as a microSD card. I couldnt count how many ROMs I tried on my mogul.
Hi guys,
Well, I've searched the forum and get close...but no cigar. So, I'll go ahead and ask.
I have an AT&T Tilt, Flashed the 6.1 from XDA MONTHS ago, and have been running Slither's Cube...not even all the time...as well as the HTC Home Customizer.
Yep, that's it.
Well, I have purchased another Tilt with a busted screen (otherwise absolutely fine) for $30 and am waiting to afford a new screen for it...at which time I'll have a backup and then the Cooking and Flashing will begin in earnest!
But I digress. Here is the sequence of events, and where I am at now:
1) Went to hang up from a phone call (BT headset active) by pressing the "Hang Up" Button...no response from the phone.
2) Pressed the Power Button...no response.
3) Slid open the Keyboard...no response.
4) Held the Power Button...no response.
5) Dumped the battery and rebooted...AT&T Splash then Radio Info...stays right there. Screen will dim after awhile, but never goes out. Rebrightens when removing external Power.
6) Soft Reset...same result.
7) Only way to Power Down is dump the battery.
8) Removed SD and SIM...attempted Bootloader Screen
9) Bootloader DOES show up:
KAIS1*0
SPL-1.93.0000
CPLD-8
Serial
10) I don't remember if there was anything with "Serial"...like a number or such...when I looked at it last (when flashing 6.1) so that may or may not be significant. There's nothing there now.
11) My Radios show up as:
R 1.27.14.09
G 22.45.88.07H
D 1.62.00.00
I am avoiding Hard Reset or Re-Flash until I can at least figure out what happened...if anyone has any ideas...or find out that this is common and that's the best or only way to solve it etc.
Since I haven't found anything quite like this in the Forum, I'm presuming that it may not be so common and I may...or may NOT...be able to find a way back before going that path. As well, I really don't want to send it off for repair...although I have insurance and coverage through Hawk (our AT&T Provider) that would be reasonable for repair ($35) but perhaps inordinate for rreplacement ($175). I'd like to be able to resolve this myself, but not knowing what may be wrong leaves me only with Hard Reset and/or Re-Flash alternatives...if those will even work...so out goes the question:
Has anybody run into this or have any idea of why it happened or the BEST recourse to resolve it?
Thanks in advance for any and all info, y'all are awesome and I truly appreciate your help...
RAF
These phones freeze all the time. Software conflicts, too much running at once, and it just feels like screwing you when you need it most. And of course all of a sudden, the hardware just crashes and never works again.
It looks like a hard reset will solve your problems, unfortunately, unless you do regular backups, you will lose all your info.
Thanks denco7!
Well, this is the first time it has locked up that early in the boot...all others have been easily resolved.
Hard Reset is not an issue with Data...I do keep my phone (data) backed up and have most of my volatiles on the SD.
And, honestly, I don't mind having to reflash or reinstall my apps...at least not yet, once I start cooking my own I feel I'll get a bit testy when I have to 'start over'.
I should probably find a good full backup app to snapshot the whole phone, then just put it back on when things 'happen'.
I do have a full backup from December using the 'supplied' app, so it will at least have most of the tweaks in it.
I'm gonna do the Hard Reset and see if that clears this, but I must say I'm not that hopeful.
Not really an expert...not a noob either...but this technology is just not rocket science, and I can actually do that along with quite a bit more.
Don't ask me to write a driver tho...I respect anyone that has that kind of patience!
Suffice to say, this just doesn't "feel" like a resetable issue...but I'm game. I'll update once attempted.
Thanks again, see you on the other side...
RAF
Okay...no joy on the Hard Reset. Behavior has stayed the same. Kinda expected that tho...
Next stop, Re-flash the ROM. I'm gonna check on latest releases of 'Official' HTC ROMs...but if anyone has any suggestions I'm open.
I'm still hoping that someone out there knows what happened here, it would be helpful to know the 'why'.
Thanks again...
not so much a suggestion but a correction. You don't have a wm6.1 rom but actually have a wm6 rom because the radio you have flashed i.e. R 1.27.14.09
is a wm6 radio not wm6.1 and that radio is only compatible with the following roms:
AT&T 1.60.502.3
AT&T 1.61.502.2
AT&T 1.62.502.0
Q-Mobile 1.2 AT&T Version
(source for above info: http://forum.xda-developers.com/showthread.php?t=393182)
so make sure that your rom matches the radio you have. I would recommend that if flashing is not something new to you than go ahead and upgrade your rom and radio to wm6.1 rom and see if the issue presists.
hope this helps
first post you stated you have a 6.1 rom but your spl is for a 6.0 rom, either your not on a 6.1 rom or your on the wrong SPL and should HARDspl if your flashing custom roms.
Thanks Guys...
I had it in my head that I went to 6.1 when I flashed it last...went out and looked at the file and sure enough it was 6.0.
This is what happens when u have 7 kids, 6 female and 4 of those in college...I'm too broke to pay attention.
No not new to flashing, and when I can get home before 10-11p some night...or this weekend...that's my plan.
Looking for the best choice 6.1 to flash and attempt to bring it back, but still curious as to the behavior in the first place.
Thanks for pointing out my ADD, and all comments are welcome...
Hoping for the un-bricking soon...
RAF
Now I'm REALLY Currious...and Frustrated! A Little Help Please...
Okay,
So I flashed the latest HTC Factory ROM: AT&T Tilt Windows Mobile 6.1 Software (ROM Version 3.57.502.2 WWE).
I wanted to do something mild at first before taking too many big steps...'small steps Ellie, smal steps'.
Once the Bootloader was up with USB showing at the bottom, I was certain I would at least have a connection to the Phone.
Of course with no ActiveSync or recognition from the PC, I simply ran the EXE and ignored the one line about making sure ActiveSync had a connection.
The only oddity was that at 13%, the Phone went from the "% Screen" back to the Bootloader Screen for a few seconds then continued normally to sucessful completion.
When it rebooted, it stayed at the AT&T initial splash and now NEVER shows the Radio or Protocol versions...just the initial splash.
As well, it does not dim the backlight after awhile as it used to nor do I ever get a Power Light...just plain LOCKED.
There is also still no way to Power Down the Phone except for removing the Battery.
Although I've never used MTTY, I'm wondering if that is now my only hope...and am currious as to the proper procedure for this particular circumstance.
I'm still searching the Forum for MTTY uses and info, but I would be appreciative if one of the Seniors could point me in the right direction.
Also, if ANYONE knows what may have caused this glitch in the first place it would help me to determine the best recourse.
Thanks again in advance to all...
RAF
Rustafergi said:
Okay,
So I flashed the latest HTC Factory ROM: AT&T Tilt Windows Mobile 6.1 Software (ROM Version 3.57.502.2 WWE).
I wanted to do something mild at first before taking too many big steps...'small steps Ellie, smal steps'.
Once the Bootloader was up with USB showing at the bottom, I was certain I would at least have a connection to the Phone.
Of course with no ActiveSync or recognition from the PC, I simply ran the EXE and ignored the one line about making sure ActiveSync had a connection.
The only oddity was that at 13%, the Phone went from the "% Screen" back to the Bootloader Screen for a few seconds then continued normally to sucessful completion.
When it rebooted, it stayed at the AT&T initial splash and now NEVER shows the Radio or Protocol versions...just the initial splash.
As well, it does not dim the backlight after awhile as it used to nor do I ever get a Power Light...just plain LOCKED.
There is also still no way to Power Down the Phone except for removing the Battery.
Although I've never used MTTY, I'm wondering if that is now my only hope...and am currious as to the proper procedure for this particular circumstance.
I'm still searching the Forum for MTTY uses and info, but I would be appreciative if one of the Seniors could point me in the right direction.
Also, if ANYONE knows what may have caused this glitch in the first place it would help me to determine the best recourse.
Thanks again in advance to all...
RAF
Click to expand...
Click to collapse
If you cannot flash a 6.1 rom or install the correct hard spl I would not even attempt using MTTY. Go to the rom section of this forum. Look for "spl rollup thread" it is a sticky from DaveShaw. Pick any 3.xx hard spl's for 6.1 rom and download. Now download jumpspl and place it somewhere on your device other than your memory card. Now run jumpspl and follow the rest of the directions in that thread. After you installed the correct SPL find a 6.1 rom and flash your device. If your sound doesn't work change your radio to a compatible radio, which would be listed in the "ultimate radio thread" by alltheway.
These are the basics. Hope it helps.
Rustafergi said:
Okay,
So I flashed the latest HTC Factory ROM: AT&T Tilt Windows Mobile 6.1 Software (ROM Version 3.57.502.2 WWE).
I wanted to do something mild at first before taking too many big steps...'small steps Ellie, smal steps'.
Once the Bootloader was up with USB showing at the bottom, I was certain I would at least have a connection to the Phone.
Of course with no ActiveSync or recognition from the PC, I simply ran the EXE and ignored the one line about making sure ActiveSync had a connection.
The only oddity was that at 13%, the Phone went from the "% Screen" back to the Bootloader Screen for a few seconds then continued normally to sucessful completion.
When it rebooted, it stayed at the AT&T initial splash and now NEVER shows the Radio or Protocol versions...just the initial splash.
As well, it does not dim the backlight after awhile as it used to nor do I ever get a Power Light...just plain LOCKED.
There is also still no way to Power Down the Phone except for removing the Battery.
Although I've never used MTTY, I'm wondering if that is now my only hope...and am currious as to the proper procedure for this particular circumstance.
I'm still searching the Forum for MTTY uses and info, but I would be appreciative if one of the Seniors could point me in the right direction.
Also, if ANYONE knows what may have caused this glitch in the first place it would help me to determine the best recourse.
Thanks again in advance to all...
RAF
Click to expand...
Click to collapse
Wow! I think you missed the advice and wisdom given to you about NOT FLASHING a 6.1 ROM with the SPL for a 6.0 ROM...
Anyways, lets see if we can help... I don't think you are going to be able to flash a SPL, as you probably can't even get an active sync connection to copy over the files...
So, try getting into boot loader screen; you hold down the camera button and then press in the rest button and hold that until a tri-color screen appears...
Then tell us exactly what it says, just to make sure we know which SPL you have... Then I will post a link to the exact ROM you need to flash to hopefully bring her back to life.
If you are not able to get into boot loader, which wouldn't surprise me, someone else with more experience un-bricking will have to help.
Some Answers and Info...Still Confused
redbandana said:
If you cannot flash a 6.1 rom or install the correct hard spl I would not even attempt using MTTY. Go to the rom section of this forum. Look for "spl rollup thread" it is a sticky from DaveShaw. Pick any 3.xx hard spl's for 6.1 rom and download. Now download jumpspl and place it somewhere on your device other than your memory card. Now run jumpspl and follow the rest of the directions in that thread. After you installed the correct SPL find a 6.1 rom and flash your device. If your sound doesn't work change your radio to a compatible radio, which would be listed in the "ultimate radio thread" by alltheway.
These are the basics. Hope it helps.
Click to expand...
Click to collapse
pjcforpres said:
Wow! I think you missed the advice and wisdom given to you about NOT FLASHING a 6.1 ROM with the SPL for a 6.0 ROM...
Anyways, lets see if we can help... I don't think you are going to be able to flash a SPL, as you probably can't even get an active sync connection to copy over the files...
So, try getting into boot loader screen; you hold down the camera button and then press in the rest button and hold that until a tri-color screen appears...
Then tell us exactly what it says, just to make sure we know which SPL you have... Then I will post a link to the exact ROM you need to flash to hopefully bring her back to life.
If you are not able to get into boot loader, which wouldn't surprise me, someone else with more experience un-bricking will have to help.
Click to expand...
Click to collapse
Hi again,
Thanks to redbandana and pjcforpres for the responses...I thought I might not get anymore!
I'll start with pjcforpres,
First, my appologies if I have not been specific enough on my descriptions...I've been attempting to be more succinct (I'm not so good at that).
This was a Stock ROM Tilt, then I had flashed RUU_Kaiser_CINGULAR_WWE_1.62.502.0_radio_sign_22.45.88.07_1.27.14.09R2_Ship.exe quite awhile back...shortly after it was available.
I added Slither's Cube and the HTC Home Screen and Customizer and have run it that way since then.
Somehow, I got it in my head that I had flashed 6.1 but I was flat out mistaken...hence the comment in the earlier part of the thread.
Then we get to the #1 post in this thread...add some confusion and voila.
The ref'd 6.1 flash was also Stock...RUU_Kaiser_CINGULAR_WWE_3.57.502.2_radio_sign_25.88.40.05_1.65.21.18_Ship.exe...and I thought I read everything, incl that it replaces the SPL.
Durring the flash, it pauses @ 13%, the USB disconnect 'bing' sounds and the Bootloader screen reappears showing SPL-3.02.000.
Then, the USB reconnect 'bing' sounds, goes back to the % screen and then completes the flash successfully.
My Bootloader screen is now:
KAIS1*0
SPL-3.56.000
CPLD-8
So...did I miss something and screw up? Or was I on the right track?
And redbandana,
It did successfully flash 6.1, but it still doesn't start...specifically, get passed the initial AT&T Splash.
Although I had already thought of going to JockyW's HardSPL 3.29, I cannot 'see' the phone in XP and therefore cannot get JumpSPL onto it...so, no HardSPL (unless I missed something else in the threads).
It DOES however give me the USB 'bing' sound when I go into the Bootloader...but clicking on the "Mobile Device" icon in Windows Exploder leaves a 'blank' right pane.
Before your post, I had read up on MTTY and noted the DON'Ts...like DON'T use task 2a!...and found several threads with commands.
None of the info commands seem to fuction, like info 2, info 7 or info 8 so I don't have much 'info' there.
One of the things I tried was 'task 28' to format the thing in case there was some corruption...this was the response:
Cmd>task 28
Format start
Storage start sector=0xC2C0, total sector=0xF000
Storage start block=800, total block=960
Total Bad Block in CE: 1
Erase physical block from 1091 to 2032
formatstorage Bad block found: 1397
formatstorage Bad block found: 1398
si backup: Erase physical block from 2032 to 2048
Format end
So I looked for 'bad blocks' on the Forum and there are suggestions to contact JockyW and GSLEON3 for more help.
I haven't as yet done this thinking I can work my way through this by searching the Forum and monitoring this Post.
My searches for MTTY Commands have shown me that there are different Commands for different SPLs, and the info is way scattered and confusing.
It is becoming clear(er) to me that I have an issue that is not that normal...or at least not with an intermediate level 'fix'.
That's why I asked for more help in the right direction, I feel like I've hit this pretty hard and done alot of footwork on my own.
I also feel like I'm running out of options and may resort to bugging JockyW and GSLEON3...unless there are any more suggestions
PLEASE let me know if there is more info that I can provide to narrow this down, or some procedure to attemt, or an MTTY comand that will give us more info, or another search in the Forum for something specific I've missed...or simply some PFM that can be performed...and I'll be HAPPY to comply!
Thanks again...and again...for the assistance, my grattitude and appreciation out!
RAF
I am going to be short and swet for the moment... my computer crashed so I am solely on my phone until I work again around 2 central time USA...
Good news is that there is a chance without MTTY to get you running, and if not, those with the knowledge are very hepful and patient.
I will do the searches tomorrow for the stock ROM you should try, and give a walk through on how to flash using a micro SD card.
I am out for now, and will get back to you as soon as I can tomorrow.
Patient and Prepared
Thanks pjc...if we can fix this I'll vote for you
I sincerely appreciate the assistace, and PLEASE let me know if there's any research I can do to facilitate.
If you're willing, let me know if I took a wrong turn somewhere or if I did something to make this worse...I like to learn from my mistakes (I AM pretty good at those...)
I just got the new screen for my backup Tilt and I'll be swapping that out tomorrow (uh...today) sometime, so I'll have a reference phone soon.
Askew but relevant, I'm on day 12 of a nasty cranial muscle spasm and 3 days into meds for it...so we'll see if I can stay focused
Thanks again and in advance...
RAF...Tilted
http://www.htc.com/us/SupportDownload.aspx?p_id=67&cat=2&dl_id=94
Try downloading from here... it is the 100% official AT&T Tilt 6.1 ROM, plus upgrade tool.
This includes everything you need, and is probably what you flashed already, but it sounds like you had a bad flash or something...
Make sure your computer doesn't go into hibernate during this process, and that you don't have anything running other than the update program and activesync...
Also, make sure when you run the update program, you right click and select 'run as administrator' or 'run as' then in the menu that comes after that select administrator.
If you can't establish an activesync connection, or if you are using Vista, and thus no Windows Mobile Device Center connection can be established, let me know, and I will track down the ROM by itself and the Radio by itself and walk you through that.
This should be the easiest fix, though, so we will try this first.
Been There, Done That...I Think ?!?
pjcforpres said:
http://www.htc.com/us/SupportDownload.aspx?p_id=67&cat=2&dl_id=94
1] Try downloading from here... it is the 100% official AT&T Tilt 6.1 ROM, plus upgrade tool.
2] This includes everything you need, and is probably what you flashed already, but it sounds like you had a bad flash or something...
Make sure your computer doesn't go into hibernate during this process, and that you don't have anything running other than the update program and activesync...
3] Also, make sure when you run the update program, you right click and select 'run as administrator' or 'run as' then in the menu that comes after that select administrator.
If you can't establish an activesync connection, or if you are using Vista, and thus no Windows Mobile Device Center connection can be established, let me know, and I will track down the ROM by itself and the Radio by itself and walk you through that.
This should be the easiest fix, though, so we will try this first.
Click to expand...
Click to collapse
1] Yep, same one I have already flashed several times to determine if there was a pattern.
2] ActiveSync will not connect...remember from #1 in this post:
1) Went to hang up from a phone call (BT headset active) by pressing the "Hang Up" Button...no response from the phone.
2) Pressed the Power Button...no response.
3) Slid open the Keyboard...no response.
4) Held the Power Button...no response.
5) Dumped the battery and rebooted...AT&T Splash then Radio Info...stays right there. Screen will dim after awhile, but never goes out. Rebrightens when removing external Power.
6) Soft Reset...same result.
7) Only way to Power Down is dump the battery.
8) Removed SD and SIM...attempted Bootloader Screen
9) Bootloader DOES show up:
KAIS1*0
SPL-1.93.0000
CPLD-8
I've never gotten passed the initial AT&T Splash since then...no matter soft hard reset flash the 6.0 ROM that was already on it or this 6.1 version.
Only difference is when I flashed this 6.1 ROM, the Radio and Protocol Versions that normally pop up at the bottom in red no longer pop up.
It now stays at the initial AT&T Splash, no versions, and never dims the backlight.
The ONLY time my Laptop 'sees' the Phone is when I put in into the Bootloader I get the USB 'bu-bingk'.
MTTY can see it, and the ROM Upgrades see it and run successfully...but Exploder can't and neither does ActiveSync.
Just to clarify that I've been there more than once...
3] Well, that I have not attempted...but all my previous flashes have gone fine (I am the only user on my Alenware Aurora m7700...and effectively I AM the Administrator), so I'll attempt that...(see next).
I downloaded, overwrote and ran this 6.1 ROM again...I set this XP install with me as the only Administrator (only user other than Guest), and I want to point something out that may be significant:
The Screnshots below show that there's no info in the Current Image Version area, I click on 'Update' and get the 2nd one.
(okay, sorry I haven't attempted very hard to embrace multiquote or embed a screenshot yet )
But this has happened every attemp to reflash after the initial sequence of events. As well, the same events recurred during the flash as all attempts before:
Durring the flash, it pauses @ 13%, the USB disconnect 'bing' sounds and the Bootloader screen reappears showing SPL-3.02.000.
Then, the USB reconnect 'bing' sounds, goes back to the % screen and then completes the flash successfully.
So...did I screw up somewhere? I really thought I had a handle on the 'small steps' that I took..it was the 'next steps' that I was mildly trepidatious about.
My understanding and instincts point to the 'bad blocks' errors durring the MTTY 'task 28' format, but I can't find anything pertinent to 'do' about it in the Forums...other than contacting JockyW or GSLEON3.
I want to try SOMETHING on my own before I go bothering them with a PM...although I've read (and even learned) alot here recently on TOP of what I had already learned over the last 2½ years, I feel I've got to at least attempt something before begging for help that way.
Still, I haven't found a path to get this basal into the core of the phone to noodle (safely mind you) around and become more adept so that I can solve these issues on my own...and it may be time to capitulate.
Let me know if you've spotted an error on my part...something I did or didn't do...or if there's another path I should take or search in the Forum I should look up.
Thanks ton again...and my appologies to all for my un-succinct pontifications...
(S)tilted...RAF
I don't think you are really doing anything wrong on your part, it just doesn't want to flash right... I had you try the stock stuff again just to make sure it was a clean download, and a clean flash.
I am not sure if it is the SPL not matching the ROM, or the Radio... The MTTY commands do indicate a problem with something not flashing right to the phone. Especially since that download has been recommended and successful so many times for people with a similar situation. I have done a fair amount of looking into this myself, and I have found a couple solutions:
1. Some people found success by flashing the same stock AT&T ROM 2 -5 times, and then it finally caught and worked right.
2. Others found luck by flashing a HardSPL, then new Radio, then new ROM.
3. They PM one of the greats... right now in the Kaiser area, JockyW is amazing! But is mostly focused on newer devices. I would recommend contacting mskip or DaveShaw. They have much more experience than I do, and should have a better idea of exactly what those block errors mean, and the solution....
If I were you I would try one last time doing a hard rest, you may need to hold down the 2 soft keys and the rest button extra long to get it to register... I would also try flashing that same upgrade 1 last time, followed by 1 last shot at a hard rest. If you still have the same stuff going on, I would contact those 2 guys and see what their wisdom says... mskip moderates the "NOOB flashing guide" thread and DaveShaw is a moderator for the Kaiser section in general.
Thanks pjcforpres...Contacting DaveShaw...Any Other Ideas?
Okay, one more time...and, no joy. Held the Soft Keys for 2 mintes solid for the Hard Reset, Reflashed, then another 2min Hard Reset.
I've resorted to sending DaveShaw a PM per the suggestion and will patiently wait for a reply.
In the mean time, if there's ANY other suggestions or a list of MTTY commands that run on the 3.56.000 SPL that can get info from the phone to help determine what the actual problem is or to correct bad blocks I'd be SERIOUSLY appreciative and VERY grateful.
Thanks to all who have responded, and in advance to all who may help from here...
RAF
A Little Updated Info:
Replaced the screen on my 'backup' Tilt, and flashed the RUU_Kaiser_CINGULAR_WWE_3.57.502.2_radio_s ign_25.88.40.05_1.65.21.18_Ship.exe ROM thaT I had flashed on the 'bricked' one.
It had the same behavior @ 13%, so I'm certain now that the flash went fine...I am even more convinced, with all of the events and symptoms to this point, that the issue lies in the 'bad blocks' reported durring the MTTY task 28 format.
I've left a PM for DaveShaw...and I AM patient...but if there is someone that may be more appropriate for this question I'd like to contact them as well. If anyone knows the right Guru, please let me know.
Thanks again to all...
RAF
Well I'm here at last sorry for the delay in getting back to you - I'm not sure how much I can help you though .
Can you post the output of "info 2" and "info 8" from an MTTY connection to your bootloader.
Also, can you please clarify: are you stuck at the bootloader (red/green/blue) or the splash screen (with R G D)?
Thanks
Dave
DaveShaw said:
Well I'm here at last sorry for the delay in getting back to you - I'm not sure how much I can help you though .
Can you post the output of "info 2" and "info 8" from an MTTY connection to your bootloader.
Also, can you please clarify: are you stuck at the bootloader (red/green/blue) or the splash screen (with R G D)?
Thanks
Dave
Click to expand...
Click to collapse
Wow man, THANKS for just bein here!
That's just it Dave, none of the info commands in MTTY seem to return anything (see #10). I've used MTTY: ver. 0.01 2001 and ver. 1.42 1997-2001 and both report literally nothing for info 2 info 7 or info 8...just another Cmd> prompt. However, (also in #10) I get to the 'bad blocks' ref running "task 28":
Cmd>task 28
Format start
Storage start sector=0xC2C0, total sector=0xF000
Storage start block=800, total block=960
Total Bad Block in CE: 1
Erase physical block from 1091 to 2032
formatstorage Bad block found: 1397
formatstorage Bad block found: 1398
si backup: Erase physical block from 2032 to 2048
Format end
Remember, the stuff in #1 of the thread happens and then I went through all this digging...took it to where I could and posted.
This wasn't a HardSPL fail or a bad Flash... I had BEEN running stock HTC 6.0 WWE with Slither's Cube, the HTC Home Screen and Home Customizer.
RUU_Kaiser_CINGULAR_WWE_1.62.502.0_radio_sign_22.45.88.07_1.27.14.09R2_Ship.exe (flashed 07/20/08)
This isn't a RUUNBH issue either, and I can get into Bootloader and I'm not 'stuck' there...currently:
KAIS1*0
SPL-3.56.000
CPLD-8
I can flash stock ROMs all day long w/no errors...flashed HTC 6.1 WWE on my backup Tilt to be sure the behaviors were the same, and they are exactly.
RUU_Kaiser_CINGULAR_WWE_3.57.502.2_radio_sign_25.88.40.05_1.65.21.18_Ship.exe runs FINE on the backup Tilt.
After flashing the HTC 6.1 WWE on the 'bricked' one however, there is no longer the R G D Radio Protocol info at the bottom of the AT&T Splash after the initial Splash...it was there before the 6.1 flash, and that's where it used to hang: Initial Splash, R G D, hang...backlight eventually dimed but never went out...battery dump only way off.
Now it hangs at the Initial Splash, NO R G D, NO backlight dim...still needs battery dump for off. It ACTS like it's lost it's damn mind...
I'm pretty sure I 'downgraded' back to the 6.0 mentioned above and went thru some similar steps to confirm, but I didn't write it all down and I'm way ADD so I can do that one again and record it all this time...unless that's a bad idea.
I very recently (like as I was searching I saw you had answered my plea...) found some other references to a MFG HardSPL that someone was thinking about working on to fix bad blocks, but I haven't read through it all yet. And, since Exploder and ActiveSync simply can't 'see' the phone, I'm not sure that I could get a HardSPL on the thing in the first place...'cause I can't get no JumpSPL on the phone itself...should've done that back when it was working I guess
I truly believe I'm at the 'needing guru help' level at this point, but if you see something I should do PLEASE point me that way and I'll dive right in. Also, like I've asked others, if you see something I did wrong or in the wrong order or whatever, please let me know that also...there's GOT to be something I can actually LEARN from this.
I warned you I tend to pontificate, but I hope that this clears up where I'm at. ANY help you can provide is fantastic and greatly appreciated, even if it's just to tell me to go somewhere else (I'm kinda used to that )
Thanks again, seriously...
RAF
In that case I have no idea. I think GSLEON3, jockyw2001 or cmonex are going to be the only one's who can help you.
Dave