Database Develop

2.21.001 downgrade

How i can downgrade version on WIZA200 (T-mobile MDA) to 2.01?
or how i can debrand ? I try to install (RUU_Prodigy_1030711_120_10410_Qtek_GER_Ship.exe) but gives error and need newer version.
br
john

GSMFLASCH said:
How i can downgrade version on WIZA200 (T-mobile MDA) to 2.01?
or how i can debrand ? I try to install (RUU_Prodigy_1030711_120_10410_Qtek_GER_Ship.exe) but gives error and need newer version.
br
john
Click to expand...
Click to collapse
Judging by your post title... you appear to have a G4...
If you determine that you have a G3 you can SuperCID & SIM unlock, then simply install the desired ROM package (.exe) from your desired provider.
Start here: http://wiki.xda-developers.com/index.php?pagename=HTC_Wizard
If in fact you do have a G4, you can flash any ROM on your device by following the procedures found (SIM unlock required for use with other provider SIMs)...
here http://forum.xda-developers.com/showthread.php?t=271043&highlight=install+any+ROM
or alternate method just for OS and not other parts look here: http://forum.xda-developers.com/showthread.php?t=271043&highlight=install+any+ROM
Make sure you understand everything that is explained on these pages before you attempt anything or you risk "bricking" your device.

i think my cingular is dead
i have a cingular 8125 Cingular 8125
IPL 2.25
SPL 2.25
Radio 02.25.11
OS 2.25.11.1
i tried to downgrade to 1.8.11 and now is dead.not even start.can i repair it?what shoul i do?

neapci said:
i have a cingular 8125 Cingular 8125
IPL 2.25
SPL 2.25
Radio 02.25.11
OS 2.25.11.1
i tried to downgrade to 1.8.11 and now is dead.not even start.can i repair it?what shoul i do?
Click to expand...
Click to collapse
First of all, why are you downgrading? Are you certain you have a G3? Did you unlock your device? If you can get the phone into boot loader mode you can recover. Flash your providers most recent ROM, put the device into boot loader mode first. READ the wiki. If you skip steps, this happens.

my phone is g4 and accidentally i've flashed a g3 rom.the bootloader is crashed.it doesn't even start.can be repaired?

G4
thx for answer,
MDA is G4 WIZARD200 2.21.0001 version, and its T-Mobile branded, which ROM is best for this MDA without branding? Germany Lng.
Because of my broblem i dont want to have any t-mobile-O2-Orange branding on phone just standart some room without any branding in Germany Language.
br
John

GSMFLASCH said:
thx for answer,
MDA is G4 WIZARD200 2.21.0001 version, and its T-Mobile branded, which ROM is best for this MDA without branding? Germany Lng.
Because of my broblem i dont want to have any t-mobile-O2-Orange branding on phone just standart some room without any branding in Germany Language.
br
John
Click to expand...
Click to collapse
Yes, just find a G3 Rom that suits your needs and modify it using the instructions in my earlier post to you and you should be able to get it on your device.

ercave1 said:
Yes, just find a G3 Rom that suits your needs and modify it using the instructions in my earlier post to you and you should be able to get it on your device.
Click to expand...
Click to collapse
I get crazy , modify is no problem to do , but i didnt find one good rom without branding in germany language, if you have time can you give me a link maybe ? thank u very much.
br

Problem

Hi, first of all i want to say thanks to all the community. I unlocked and upgraded my G3 device thanks to this forum.
i have a friend who installed jpchme windows mobile 6 spanish rom over the previous rom (i don't know wich version was).
I told him he try to install 3.08 rom but the program didn't recognize any connection with the phone. My mistake....that's the problem.
And now his pda is stuck at bootscreen loader with IPL and SPL 1.08. But we don't know if it was a G4 or G3 device. I know....1.08 means it's a g3 device but is there any chance that the pda was a g4 device and when he installed windows mobile phone the ipl and spl appear as a g3 ?
What should he do ?
thanks

zeba5 said:
Hi, first of all i want to say thanks to all the community. I unlocked and upgraded my G3 device thanks to this forum.
But know i have a friend who installed 3.08 rom (for G3 devices) directly (without installing button rom before) and now he's stuck at bootloader screen. While the rom was installing it crashed and say connection error. Now we don't know what to do.
The IPL and SPL numbers are both 1.08 but he doesn't remember wich numbers appear before, so is there any way to see if it's a G3 or a G4 device in bootloader mode ?
thanks
Click to expand...
Click to collapse
Fortunately for your friend, yes there is. In bootloader mode, it displays your IPL and SPL. If they look like this, 2.xx then it is a G3. If it looks like this, 2.xx.xxx1 then it is a G4 and if he tried to flash IPL/SPL 3.08 which is STRICTLY for G3 devices, his device may be his new favorite paperweight.
Give this a try. Find and download his carriers latest Rom. Pull the battery out of the device and leave it out for about 2 seconds. Put the battery back in and then hold the camera button while pressing the power button. This will put your Wizard in bootloader. Flash his carriers latest official Rom and that should get him back to WM5.
Hopefully this works for him but if it doesn't then he may be screwed. On the other hand, if it does work for him, do him a favor and make him read read read before he tries to flash the phone again. I hate to see a Wizard turn into a paperweight because someone was too lazy to just read first.
Dan.

dharvey4651 said:
Fortunately for your friend, yes there is. In bootloader mode, it displays your IPL and SPL. If they look like this, 2.xx then it is a G3. If it looks like this, 2.xx.xxx1 then it is a G4 and if he tried to flash IPL/SPL 3.08 which is STRICTLY for G3 devices, his device may be his new favorite paperweight.
Give this a try. Find and download his carriers latest Rom. Pull the battery out of the device and leave it out for about 2 seconds. Put the battery back in and then hold the camera button while pressing the power button. This will put your Wizard in bootloader. Flash his carriers latest official Rom and that should get him back to WM5.
Hopefully this works for him but if it doesn't then he may be screwed. On the other hand, if it does work for him, do him a favor and make him read read read before he tries to flash the phone again. I hate to see a Wizard turn into a paperweight because someone was too lazy to just read first.
Dan.
Click to expand...
Click to collapse
thanks for the answer! now it shows 1.08 IPL and SPL. But if he has an g4 device and flash with 3.08 rom wich is for G3 devices, what would IPL and SPL show ? are you sure that if it show 1.08 now it's a g3 device ?
oh, and here we don't have any support from carriers so can he install button 1.05, then 3.08 and then some windows mobile 6 rom ?
thanks

zeba5 said:
thanks for the answer! now it shows 1.08 IPL and SPL. But if he has an g4 device and flash with 3.08 rom wich is for G3 devices, what would IPL and SPL show ? are you sure that if it show 1.08 now it's a g3 device ?
oh, and here we don't have any support from carriers so can he install button 1.05, then 3.08 and then some windows mobile 6 rom ?
thanks
Click to expand...
Click to collapse
with IPL/SPL 1.08 it shud be G3 device,try to download official carrier rom from the website and flash in the boot loader mode,by carrier means,the rom which it came first pre installed with,which version of rom was installed before he flashed ipl.spl 3,8,was it t-mobile or cigular,that wud be the carrier rom,download from it's website and flash,or you may try to download t-mobile 2.26 or wizard_love_rom and flash,it may do the trick.good luck

'so can he install button 1.05, then 3.08 and then some windows mobile 6 rom ?'
well, if it's a G3 and it shows ipl/spl 1.08,then button's can be flashed,but make sure it's IPL and SPL both are 1.08.but if it's like IPL 1.08 and SPL 3.08,than I'm afraid,it had to be flashed with official rom to bring it down to first ipl/spl 2.xx---> 1.05.Don't directly flash button's 1.05 to bring it down to ipl/spl 1.05,it'll brick the phone.download the official rom or T-Mobile 2.26 which also is a stock rom and flash.

damn. i don't know why i told that he installed 3.08 rom.
he installed jpchme windows mobile 6 spanish rom over the previous rom (i don't know wich version was).
I told him he try to install 3.08 rom but the program didn't recognize any connection with the phone.
And now his pda is stuck at bootscreen loader with IPL and SPL 1.08. But we don't know if it was a G4 or G3 device. I know....1.08 means it's a g3 device but is there any chance that the pda was a g4 device and when he installed windows mobile phone the ipl and spl appear as a g3 ?
what should he do ?

zeba5 said:
damn. i don't know why i told that he installed 3.08 rom.
he installed jpchme windows mobile 6 spanish rom over the previous rom (i don't know wich version was).
I told him he try to install 3.08 rom but the program didn't recognize any connection with the phone.
And now his pda is stuck at bootscreen loader with IPL and SPL 1.08. But we don't know if it was a G4 or G3 device. I know....1.08 means it's a g3 device but is there any chance that the pda was a g4 device and when he installed windows mobile phone the ipl and spl appear as a g3 ?
what should he do ?
Click to expand...
Click to collapse
Ok relax,if ipl/spl 3.08 was flashed to a G4 device,it'll brick the device,it won't go into boot loader screen.As you say that it goes into boot loader mode,than cool down he's safe cuz due to different Os version being a spanish it had a bad flash,nothing to worry.but remember a G4 device will never show an ipl/spl 1.xx no matter what happens it always will show 2.xx.xxx1.
Just as I have told you to download official rom or T-Mobile rom and do the following :-
1. Make sure your phone is not Connected to the PC and remove the dummy card or SD/MMC card
2. On your Desktop PC, open Microsoft ActiveSync, then go to File >Connection Settings >Remove the Selection from “Allow USB Connection with this desktop computer”
3. Reconnect your phone to the Desktop PC using the USB Cable (Don’t use Bluetooth for the Upgrade)
4. Run the Upgrade again and it will work fine without any problems.
While upgrading, the ActiveSync program will not go on, however the upgrade is running.
Hope it'll work,good luck

zabardast_1 said:
Ok relax,if ipl/spl 3.08 was flashed to a G4 device,it'll brick the device,it won't go into boot loader screen.As you say that it goes into boot loader mode,than cool down he's safe cuz due to different Os version being a spanish it had a bad flash,nothing to worry.but remember a G4 device will never show an ipl/spl 1.xx no matter what happens it always will show 2.xx.xxx1.
Just as I have told you to download official rom or T-Mobile rom and do the following :-
1. Make sure your phone is not Connected to the PC and remove the dummy card or SD/MMC card
2. On your Desktop PC, open Microsoft ActiveSync, then go to File >Connection Settings >Remove the Selection from “Allow USB Connection with this desktop computer”
3. Reconnect your phone to the Desktop PC using the USB Cable (Don’t use Bluetooth for the Upgrade)
4. Run the Upgrade again and it will work fine without any problems.
While upgrading, the ActiveSync program will not go on, however the upgrade is running.
Hope it'll work,good luck
Click to expand...
Click to collapse
thank you very VERY much. I'll give him the t-mobile rom and i hope it recognize the device!

wizard stuck on bootloader

hello.
i had problem with wizard. i tried to upgrade rom, but i cant. it stuck on 99% and gives an error. i think it had cidlock, but i cant unlock it from bootloader.
Please help...

Piechcio said:
hello.
i had problem with wizard. i tried to upgrade rom, but i cant. it stuck on 99% and gives an error. i think it had cidlock, but i cant unlock it from bootloader.
Please help...
Click to expand...
Click to collapse
Download official stock rom of your carrier and flash it in bootloaders to recover back to its default working status,then if its a G3 phone, downgrade to ipl/spl 1.xx by flashing Button's Rom and SIM/CID unlock with lokiwiz02b,but if its a G4 ,it cannot be CID unlocked but can be upgraded to wm6 through 'SoftSPL' or 'HardSPL'.

HI
I have a same problem – I have a qtek 9100 G3
ipl-spl 2.17
GSM 02.07.10
OS 2.17.7.2
I can update my rom completely but after restart freeze on ipl-spl screen
And I can’t warm reset it says FORMAT PARTITION FAIL
I try to downgrade my rom but spl freeze on 2.17 – I try button rom and Xda_MiniS_LaunchROM_v154102
I can’t find any official qtek rom for test
And I also try R2SD all with romupdate115 it not work
help please

jalalkarimi said:
HI
I have a same problem – I have a qtek 9100 G3
ipl-spl 2.17
GSM 02.07.10
OS 2.17.7.2
I can update my rom completely but after restart freeze on ipl-spl screen
And I can’t warm reset it says FORMAT PARTITION FAIL
I try to downgrade my rom but spl freeze on 2.17 – I try button rom and Xda_MiniS_LaunchROM_v154102
I can’t find any official qtek rom for test
And I also try R2SD all with romupdate115 it not work
help please
Click to expand...
Click to collapse
You got to have a CID unlocked phone to upgrade to any wm6 Rom.Sometimes SPL do get stuck up at 2.xx while downgrading with Button's Rom,it takes a couple of tries to get it downgraded to 1.xx.Flash the button's rom a few times more till it gets downgraded.You can only CID unlock your phone,if it has IPL/SPL 1.xx.
Download the official stock Qtek Rom from this link:-
http://forum.xda-developers.com/showthread.php?t=342744

zabardast_1 said:
You got to have a CID unlocked phone to upgrade to any wm6 Rom.Sometimes SPL do get stuck up at 2.xx while downgrading with Button's Rom,it takes a couple of tries to get it downgraded to 1.xx.Flash the button's rom a few times more till it gets downgraded.You can only CID unlock your phone,if it has IPL/SPL 1.xx.
Download the official stock Qtek Rom from this link:-
http://forum.xda-developers.com/showthread.php?t=342744
Click to expand...
Click to collapse
Don't use those ROMs as they are for G4!!!
If flashing original ROM doesn't solve the case then you'll have to buy the unlock program from IMEI-check company.

Many thanks
Can you give me some advice what is the best version for qtek 9100 I can’t find any original qtek rom please give me a link
And if I buy IMEI Program after apply that my device starts normally?
I don’t want WM6 only back to normal
And serious problem is
I have FORMAT FAT FAIL for warm reset. In this case its possible hardware (disk on chip) has a hardware problem?
Thank you all

jalalkarimi said:
Many thanks
Can you give me some advice what is the best version for qtek 9100 I can’t find any original qtek rom please give me a link
And if I buy IMEI Program after apply that my device starts normally?
I don’t want WM6 only back to normal
And serious problem is
I have FORMAT FAT FAIL for warm reset. In this case its possible hardware (disk on chip) has a hardware problem?
Thank you all
Click to expand...
Click to collapse
No. the problem is simply of messed up firmware. I believe that the SPL tries to load the OS but it must be at a different address and never starts to load.
The IMEI-check tool will simply CID unlock your device. You still have to do the "r2sd all" procedure...
good luck

AKU3 stuck

format is failed after a power outage in the middle of ugrading with shell tool.
made it worse bu trying to flash with tmobiles latest rom.
so now i'm stuck in boot screen with the following
Device is g3 with
IPL 3.08
SPL 3:08
GSM 02.69.11
OS 3.8.2.1
did i mention CID unlocked?
please advice

rephrase
Let me rephrase the question.
I have a friend who saw me use shell tool to upgrade my cid locked wizard.
He went home to try the same on his cid locked g3 wizard.
he had bad luck and it was interrupted mid way through so he brought me his dead wizard.(stuck on bootloader)
The only official rom i had was Tmobile's 3.08 so i flashed it to try and revive it.
it flashed and finished but still stuck on bootloader.
when i try and hard reset it says "format is failed".
button rom wont work, wizard love wont work, sd method wont work as it is cid locked.
Any ideas?
And if none, will imei-check work..

Get the official stock ROM for his Wizard, then flash it and you will get a working Wizard back.
However, if the IPL and SPL still stays at 3.08, there is possibility that IPL and SPL not downgradeable, so unlocking may not be possible.
Another thing...by CID unlocking the Wizard, there is no reason to use ShellTool while you can actually use RUU directly! Using ShellTool may lead to incomplete update!

Not yet home
Hey, the stock rom (tmobile 3.08) succesfully flashes but the wizard still doesnt boot. it gets stuck on the first screen.
Any more ideas?
BTW i'm very experimental so i'll try anything..

Hi,
Have you tried to flash the wizard with Hard-SPL or Soft-SPL.
I had the same with mine wizard (G4) but Hard-SPL worked for me.
You have a G3 so I don't no if it will work. Otherwise read this thread first post
Hope it will work.
Peter

pd2903 said:
Hi,
Have you tried to flash the wizard with Hard-SPL or Soft-SPL.
I had the same with mine wizard (G4) but Hard-SPL worked for me.
You have a G3 so I don't no if it will work. Otherwise read this thread first post
Hope it will work.
Peter
Click to expand...
Click to collapse
Both solutions advised require WinCE to boot to be applied... which isn't the case here

hey
mestrini said:
Both solutions advised require WinCE to boot to be applied... which isn't the case here
Click to expand...
Click to collapse
So mestrini,
What to do??
will imei-check work?
And what exactly is format is failed?

Try this thread http://forum.xda-developers.com/showthread.php?t=298613
This worked for a friend of mine. he has a G3.
Peter

Need help!!

Hello Guys,
I have the cingular 8125 G3 and I need to load a rom into it. I have try to load 2 diferent roms but neither worked. I have followed this thread: http://forum.xda-developers.com/showthread.php?t=310831 but nothing.
Here's the thing, after I load the rom the screen says:
IPL 1.01
SPL 3.08
GSM 01.12.10
OS 1.5.4.2
Any help I would really apreciated. If you want I can donate too.
Thanks

Try to flash back to Button's ROM, then try to use Wizard Service Tool to unlock CID and verify that CID is unlocked in WST.
After unlocking successful, you can flash with any ROM you want.

Thanks for the answer.
Now, just for my records, how do you flash back to buttons rom?
Is it to flash the original rom?

arys64 said:
Hello Guys,
I have the cingular 8125 G3 and I need to load a rom into it. I have try to load 2 diferent roms but neither worked. I have followed this thread: http://forum.xda-developers.com/showthread.php?t=310831 but nothing.
Here's the thing, after I load the rom the screen says:
IPL 1.01
SPL 3.08
GSM 01.12.10
OS 1.5.4.2
Any help I would really apreciated. If you want I can donate too.
Thanks
Click to expand...
Click to collapse
You already got IPL 1.xx,there's no need to flash back to Button's Rom,just try to CID unlock with WST Tool,hope it'll work out.

I tried that but the thing is when i turn on the device it comes up with a screen and the info I've said before. It doesn't go anywhere else. Just to that screen that have this info in red colored.
and everytime i want to flash a rom into it, the device says flashing from language cingular, and it never changes. How can i put it back to factory default?

Thanks for all your help guys, I couldn't fix it so I sold it as is.
I really appreciate what you have done.
If there is anything I could do, let me know.
Have a great one....

First enter bootloader by pressing Camera+reset. After enter the tri-color screen, flash with Button's ROM.