Database Develop

Wifi and use of IP address

I cannot connect to wifi. It says connected and it says i have an IP address but i can't navigate to any webpages. I use WEP and have WM5. If I enter a wrong wep key it won't connect so i feel that i am actually connected to the network just my device isn't realizing it. Is there any manager like the cooked rom of 2003se where i could manually choose WLan as my option to connect to the internet. I have also tried turning off wep on my router and other settings like that. Changed in between connected to work or the internet. Any ideas?

I found the problem. for some reason it was trying to connect on my gprs proxt server. that would always deny the connection. I had to set up my GPRS as my work connection and a generic connection that connected to the internet and ONLY put this network connects to the internet. Also it only worked if i used the existing my work connection and didn't work if i created my own with the same settings..
All is now well in thw WM5 world.. no more resets!!! think this might be a bug though..
I just realized that this ONLY pertains to ATT GPRS settings because they are the only ones who need to set up a proxy server..

now that connections work with my wifi i have one problem and this occurs with GPRS also.. my connections seem to time out. I was trying to download about 50k of mail and after about 10 messages it says "Unable to connect to incoming mail server" I've been connected just fine.. then the connections fails.. i have to do it all over again..

Confused: WiFi setup please....

I'm confused. My IE instance quite happily connects to my 3G t-mobile connection when no connections are enabled. However, when I enable the WiFi - the little mast icon says connected... but IE can't find anything. I'm assuming its a DNS issue. I've tried disabling MAC address security, and it made 0 difference to the failure to connect - so I'm assuming the MAC address I typed into my router was the right one. (Can't even find the TyTnII MAC address now!)
So - what do I need to do to ensure that the TytnII loads the WiFi connection when at home, and actually allows me to surf? I tried putting in the router address as DNS - and it didnt make any difference either. What next? Too many options!!!!
Graham

If its over a wep network(which it probably is) you need the key(passcode)...

Nope - got that - (and it only prompted for the passkey once - so I guess it stored it somewhere). Its got something to do with DNS - because it cannot resolve names (like google.com!) - but I don't know how to check this out. Are thetre tools like TRACEROUTE / IPCONFIG etc for WM6??
Graham

Try removing any proxy servers that might be configured.

Go to settings/connections/wi-fi and tap your connected Wireless Network to configure. In next screen check if "Connects to:" is set to "The Internet" . If set to "Work" IE will use your 3G dataconnection. When set to "The Internet" IE will use your WI-FI connection. When you are outdoor and your home WI-FI connection is not available IE will then automaticly use your 3G connection again.
Hope this helps as it works this way with me.
Klipper

I am having this same problem , did you manage to sort yours out ?

Does your WiFi network use a proxy to get to the internet?

installer09 said:
I am having this same problem , did you manage to sort yours out ?
Click to expand...
Click to collapse
Yep - I reset my wireless router - and everything started working. Looking in the wrong place as always!
Graham

And how do you connect to public wi-fi spots without havin TyTN try to connect over 3G?
Thanks

Kaiser and VPN

Hello,
does someone use a VPN software on the Kaiser ?
Wich one ?
I tried several but none worked.

My Kaiser is using the built in VPN client, to VPN into two different Microsoft RRAS networks using PPTP and IPSec/L2TP.
What problems are you experiencing? What type of networks are you trying to VPN into?

Thanks a lot for your answer !
I didn't know the Kaiser had a VPN client included ...
Where is the application ? What's its name ?
Is there a documentation I can find somewhere to help me to configure it ?
The other thing is that I use a SecurID password to connect to my corporate network, I don't know if this can work also with the Kaiser VPN.
In fact I would like to connect to my corporate network wich accepts both IPSec/UDP and IPSec/TCP. All I know is that I need a Cisco compatible VPN application.
I tried "AnthaVPN", it connects to our Cisco server, but then it disconnects after a few "Time Out" errors.
Thanks again for your help !

I would be interested in this too... we use Cisco at work using Cisco ipsec/udp but no idea how to set this up on the phone

Finally I've found how to use the buit in VPN, but it still does not work for me, because of the SecurID password I think (it says my login/password may be incorrect).
Here is how to access to the built in VPN (my device is french, I translate it to english but I'm not sure the names will be the same on english devices):
parameters/connections -> choose the "Connections" icon.
Then choose "Modify/Configure my VPN servers"
After you filled everything there, choose "Manage existing connections".
At the bottom of the screen, choose "VPN". The VPN connection you made should appear here.
Put your stylus on it until the options "delete" and "connect to" appears.
Select "connect to" and then you should be connected to your network.
I hope this helped.
So finally, I am still searching for a VPN application wich would work with SECURID passwords.
Does someone know one ?

Cisco VPN Help Required
Even my office uses a Cisco PIX Firewall with VPN. Even i have tried many softwares, but nothing seems to work. I thik it is because of the 2 phase authentication of the Cisco VPN.
Also just for info, we use IPSec over UDP (NAT/PAT)
How to set this up in my KAISER?

Hello to all
Im using AnthaVPN and it's work great with Cisco VPN Concentrator System in my KAISER. There must be also a way to connect to a pix.
http://forum.ppcwarez.org/viewtopic.php?f=41&t=32009&hilit=AnthaVPN
Greets
Haija

Like I said, I tried this one, but it did not work with SecurID keys.
I also had a problem with it related to the WIFI :
when I tried to use it with WIFI enabled, if I wanted then to disable the WIFI, it was impossible, even after a soft reset. I had to deinstall AnthaVPN to be able to disable the WIFI.
So finally I think the built-in VPN is better than AnthaVPN because I had no WIFI issue with it.

I have read the manual from the Homepage AnthaVPN and for me its OK. But i haven't testet over wifi. Over GPRS works great.

i'm using the Bluefire VPN CLient (www.bluefiresecurity.com) to connect to my university's vpn (cisco) and it's working great.
with AnthaVPN i was not able to disconnect wifi anymore (phone would hang up -> soft reset -> wifi on again), don't know if they fixed this till now

So I was not alone to have wifi problems with AnthaVPN !
Finally I tried Bluefire VPN, it works a lot better than AnthaVPN (no more wifi problems !), I can go upto the SecurID login, but after that, at "Phase 2", I have an error code talking about IPSec parameters...
So I still have problems but now I know that Bluefire is working with securid keys.

WLAN Problem Diamond

ok, first of all, i checked every single thread on this page hoping to get a solution for my problem.
HTC Diamond, D-Link DWL-900AP+ Access Point.
My Diamond can "see" the Access Point, but is unable to connect with it.
Authentification WPA-PSK
Encryption TKIP
Networkkey Manually inserted and 100% correct.
Hook set at IEEE802.1x
EAP Typ = Smartcard or security certificate (but it's greyed out)
Network Card connects to Internet
From Server given IP Adress (hook set) DHCP on Access Point enabled
MAC Filters disabled
I also played around with the available network tabs.
I have vodafone DE, vodafone internet, company network or ISP
The the slider of the energy saving modus ist set to best performance.
What the hell is going wrong????
I also owe a HTC Touch Elfin and have no problems to access my network/internet.
Any suggestions would be highly appreciated
thank you

try deleting your network saved setting from list, make sure network card connects to internet, not work, find access point, and enter your password again.
this works for me in similar situations.
works if you start fresh, and not trying to connect with the same settings. i dont know why but has saved my ass a few times.

Also, try changing the encryption from TKIP to AES and see if that works....

I have the same problem! It's something about DHCP. My Diamond connects to my home wifi onli if I set the IP (which belongs to my phone on access point) address in the properties of network adapter.

HI did you try to put the host address of a site?
write 64.233.167.99 instead of google.it in case you can see the page the problem is the dns not resolved and insert manually in your phone connection

Marcellus_pnz said:
I have the same problem! It's something about DHCP. My Diamond connects to my home wifi onli if I set the IP (which belongs to my phone on access point) address in the properties of network adapter.
Click to expand...
Click to collapse
Same here, it looks like a DHCP time-out or routing problem. I've set up a DHCP server with a small pool of adresses on the acces point itself and now my Diamond always connects correctly. Before that, my Diamond would state that i had entered a invalid security key.

diamond connects but i cannot visit any website
Hi,
I have a similar problem. My diamond gets an ip address from dhcp, connects to dwl-900ap+ but i am not able to open any website (I tried to open some web with url and with its ip address too) - tried opera and IE too. In opera i get a "could not locate remote server" error. (Looks like a DNS problem?) I am not even able to open the AP's configuration web with diamond. Every other wifi enabled equipment I tried (1 notebook with win vista, 1 with XP, 1 with debian linux, nokia n95 with symbian and e-ten m700 with win mobile 5) works without a single problem. I also tried to reset the AP and my diamond - without success.
I didn't change any setting on the AP except for setting up a WEP encryption (i know, i know, it's not a strong encryption ), the SSID and the AP's ip address. Everything else is default. My dhcp server is not the access point. DHCP runs on a similarly configured router with wifi AP (diamond connects without problem).
Any idea/solution? thanks

Connecting to ADSL Modem using WiFi

Hi,
I have ADSL modem, and I am trying to connect to the modem (via WiFi) and use internet on my HTC VIVA.
My internet connection requires authentication in order to connect. I can successfully connect to modem using Wifi connection. In order to connection to Internet, I added new VPN server from settings > Connections > Edit my VPN servers. I added all the credentials as provided by my ISP, however I am not able to connect to internet and access web pages from the Internet explorer of my device.
Please help me and let me know where I am going wrong?
Thanks,

You don't have to set your authentication data in your Viva.
All you need to do is connect to your ADSL modem using WiFi and start browsing the web. It should work correctly unless your ISP requires a proxy server.
Tell us what happens.

Hi GFX,
Thanks for replying. I connected to ADSL using WiFi, but when I open Internet explorer I get page not found.
When I was in US, I was able to access Internet as per your reply. But now I am in India and I am not able to access Internet.
Some of the differences that might help you or any other who would like to contribute
USA India
====== =======
ISP Comcast BSNL
Authentication WPA2-PSK Open
Data Encryption AES WEP
Thanks,

I'm not sure what's causing this.
Probably your ISP requires a proxy server. Can you connect to the internet using your PC??
The other thing is, your ISP has nothing to do with your ADSL modem authentication and data encryption modes! You can set these settings manually according to your personal needs. Read your ADSL modem user manual for more information.
A WPA2 authentication is recommended so you can protect your modem & internet connection from outsiders and hackers.
Check your ISP's website to see if they require a proxy server. And tell us about your ADSL modem brand and model so we can help you.

My ISP does not require proxy server, and I can connect to Internet using my PC. I am able to connect to my ADSL modem but somehow I am not able to connect to Internet.
Following are the details of my ADSL modem
Brand: Huawei
Model: WA1003A
Its an ADSL router.
Thanks,

OK, please check the following settings in your device:
1- Goto Start-> Settings -> Connections -> Connections-> Advanced tab-> tap on "Select Networks", and check that the first dropdown menu says "My ISP".
2- Goto Start-> Settings -> Connections -> Wi-Fi -> Network Adapters tab, and check that the first dropdown menu says "The Internet".
If you made any changes to the above settings, try to reconnect to the modem once again, it may work this time.
However, if you left the above settings unchanged then your problem lies somewhere else. Check if you can access the internet using Opera Mini, or try connecting to another router. Because we need to determine the source of the problem.
Good luck.

have you simply tried connecting via wifi with default settings?
when you switch on wifi, once the network is detected, you can feed in the values then right? sorry if this seems like a stupid answer but we often miss whats right under our noses,

Sorry for replying so late, was busy with lots of work for some time.
GFX: My connection settings are same as you mentioned. But even with these settings in place, no success.
karthiksk: I get connected to WiFi network, but after this I don't get any popup box in my device to enter the details.
Guys, however I got the solution, since my network uses PPoE, I had to configure these settings in my Modem. Earlier I was entering ISP credentials in an external PPPoE client on my PC, this way I can access Internet with only one PC at a time and WiFi was also not working.
I entered ISP credentials in my modem and configured PPoE settings. Now I can connect my PC (using Ethernet cable), my laptop using WiFi and my HTC device using WiFi at the same time.
Thank you all for helping me in trying to resolve this issue.

Good to see your problem solved.
Turns out it has nothing to do with your device!
Enjoy your Viva, it's a wonderful device.

vijay1234 said:
Sorry for replying so late, was busy with lots of work for some time.
GFX: My connection settings are same as you mentioned. But even with these settings in place, no success.
karthiksk: I get connected to WiFi network, but after this I don't get any popup box in my device to enter the details.
Guys, however I got the solution, since my network uses PPoE, I had to configure these settings in my Modem. Earlier I was entering ISP credentials in an external PPPoE client on my PC, this way I can access Internet with only one PC at a time and WiFi was also not working.
I entered ISP credentials in my modem and configured PPoE settings. Now I can connect my PC (using Ethernet cable), my laptop using WiFi and my HTC device using WiFi at the same time.
Thank you all for helping me in trying to resolve this issue.
Click to expand...
Click to collapse
You wont believe how often the answers to your question are right under your nose,
and like GFX said, enjoy your VIVA!

deepaksadhvani said:
Dear Vijay,
I am facing the same problem to connect my E61 handset to BSNL Huwaei modem. Can you give me the steps to configure the same.
I can connect to the modem, just let me know what configuration changes are to be made to enable access from mobile phone.
regards,
Deepak Sadhvani
90300 60500
Click to expand...
Click to collapse
This is a Windows Mobile and HTC VIVA forum, it is highly unlikely that you will get your solution here. and it is unsafe to post you mobile number.

I'm facing the same problem..it's not the ISP or modem..it's only & only viva...
It sucks badly...I purchased two different modem router..one of netgaer and other one of linksys...and the didn't work on both of them...wifi only works with the modem ZTE ZXDSL 531B
**** off viva...