An yone know where I can buy a replacement part in the uk?
What happened to it ? Same as mine I guess ? It kind of "imploded" ?
1. No, it simply got too hot and dropped off!
2. Have you sourced a replacement?
1. Mine has a small hole in it. Don't know how.
2. Sorry, no. I'm thinking about dripping a drop of glue inthere...
Careful with the glue, I managed to put some inside the phone and had to send it to repair. Now the rubber thing is loose again but this time I will put the glue to the rubber part and then put it to the phone
I had a nice drop of glue on it. But as soon as I tried to use it, it fell off. There was still a small piece of rubber on the stick. I pelt it off and there came this little hole. I think the hole is all the way through, so I can't use any glue anymore.
Now I'm thinking of buying some 2-face sticky tape and fabricate a little piece of rubber or plastic on it. Should work okay...
Related
Hey guys
After trawling through Google, eBay and XDA I haven't been successful in finding anywhere that sells replacements for the black panel/sticker things that have to be ripped off in order to take the phone apart. I might be getting a Milestone with a broken digitizer in a few weeks and, judging from disassembly guides, you have to be pretty rough with these bits to get them off.
I'm talking about the copper bit, the top bit and the bit with the Google logo, all on the rear of the phone.
Any help would be much appreciated!
One more thing: would I be right in thinking that the 855 and 853 digitizers are interchangeable?
In the states I have seen these things from one seller on ebay, quite expensive though. If caution is exercised, all can be removed with little or no destruction to them. If you have a hot air gun. that also helps to soften the glue.
The only one that may get a little bent is the metallic grille. Careful on this with the heat gun if you use one, my first droid I accidentally set it to high heat, and the grille shriveled up as if it were plastic. I would use a razor flush with the grill and slowly work it under, if you start at one end and pull like in the guides I've seen, it will definitely bend.
The other two can be removed with a soft plastic splunger tool, just start at one end and take your time freeing it from the glue, the one with the google logo is brittle and can crack, also if you are too ruff, the black will scratch off the back of it. The top piece is pretty sturdy and a piece of cake, I had a skin on one Droid and the two top pieces came up together.
If you do mess them up and can't find replacements, and the phone is yours, who cares? rock it out with an ugly back
bitz_dv said:
In the states I have seen these things from one seller on ebay, quite expensive though. If caution is exercised, all can be removed with little or no destruction to them. If you have a hot air gun. that also helps to soften the glue.
The only one that may get a little bent is the metallic grille. Careful on this with the heat gun if you use one, my first droid I accidentally set it to high heat, and the grille shriveled up as if it were plastic. I would use a razor flush with the grill and slowly work it under, if you start at one end and pull like in the guides I've seen, it will definitely bend.
The other two can be removed with a soft plastic splunger tool, just start at one end and take your time freeing it from the glue, the one with the google logo is brittle and can crack, also if you are too ruff, the black will scratch off the back of it. The top piece is pretty sturdy and a piece of cake, I had a skin on one Droid and the two top pieces came up together.
If you do mess them up and can't find replacements, and the phone is yours, who cares? rock it out with an ugly back
Click to expand...
Click to collapse
Thanks By chance I bought a heat gun to fix something else the other week... Unfortunately it seems like the one I won on eBay has been tampered with already as the copper is 'disturbed'. Oh well... Like you said, I guess it'll just be unique I could buy a vinyl instead.
PS If you ever find that eBay listing, please tell me
Edit Again: Yay, finally found the mesh on eBay. If anyone else needs a replacement it's here.
Anyone know how to get the front bezel off this thing?
It's begging for a paint job.
Thx!
and perhaps a generous application of rubber cement. I had ONE creek point when i bought it - annoying but livable enough (plus the fact all the bad hours of xmas I was working I never had time to return it in the 30 day period to best buy). now almost 2 months latter theres three...
theres a teardown thread or two on here somewhere but the search button seems to be failing (or my browser....)
- Will.
It must pop off, but I don't want to be the guy to try it...
In the tear down I remember seeing roughly 10 small philips screws holding it from the inside to the metal sub structure. To tighten it you need to remove the back of the device then you will see the screws running around the perimeter. I also remember the screen is held to the bezel with a form of double faced tape.
waremaster said:
In the tear down I remember seeing roughly 10 small philips screws holding it from the inside to the metal sub structure. To tighten it you need to remove the back of the device then you will see the screws running around the perimeter. I also remember the screen is held to the bezel with a form of double faced tape.
Click to expand...
Click to collapse
Its funny because the guy at Best Buy was trying to pull the back off of the one I returned... No idea why he was trying to yank the back off of it...
I guess if he had succeeded I would have seen the screws..
Funny enough the display model NookColor at my local best buy was practically falling off. When I first looked at the device I nearly did not buy one because of that but then getting one in my hands at B&N changed my mind.
The front bezel is a "tape and cover" paint job. The screen is glued to the frame pretty solid. I had mine apart to fiddle around and to get the back off for a mold. Most of the screws are Torx #5 or #6. Tape it off good and you should be ok as far as the front bezel. The rear and metal frame you can easily get to by proper disassembly.
Here's the zdnet guide,
http://www.zdnet.com/photos/nookcolor-teardown/487636?seq=21
Here's what I did.
You'll need a torx 5. After you unscrews the 2 screws by the sd slot, use your nail along the chamfer corner to lift the back siding up. Then use a credit card to lift the back up and run along the edge to unhinged the back.
techboydino, are you going to make a new front bezel? might be a small after market for such things. I'd pick up a more solid one if the price was right.
actually metal front and back pieces would rock...
- Will.
I would like to see a silicon back cover case that has a kickstand..
WillCameron said:
techboydino, are you going to make a new front bezel? might be a small after market for such things. I'd pick up a more solid one if the price was right.
actually metal front and back pieces would rock...
- Will.
Click to expand...
Click to collapse
I was really considering metal but the fact that most would have to really take special care to actually seperate the bezel from the screen really kind of set me off that. making a case for this is rediculously hard. (compared to my attempts at other devices. if you ever seperated a screen for a cell phone from the glass then you know what I mean. I am trying to replace the back with aluminum and wanted to do a carbon fiber front. so far everything is too thick or just plain looks bad.
Ever heard of masking tape?
3M BLUE painters tape FTW
Glad to find this post!!!
This maybe a little off the subject but does any know where I can purchase a replacement faceplate frame cover.
I accidentally drop my nook color and now it has a nasty crack...
Thank you all in advance!
i took the kickstand off a picture frame...white glued it and had one. Then took it off to fit my new cover...replacement kickstand not put on yet..
nookme said:
This maybe a little off the subject but does any know where I can purchase a replacement faceplate frame cover.
I accidentally drop my nook color and now it has a nasty crack...
Thank you all in advance!
Click to expand...
Click to collapse
Your best bet is probably to pick up a smoked one off EBay or one with a cracked screen and a good bezel.
Actually post up WTB (want to buy) dead Nook Color in the XDA market and link to it in this thread. I seem to recall a couple readers here who have more than "gently used" Nooks....
The screen on my Rogers HTC Raider is scratched. It is deep enough that I cannot remove by applying polisher. Screen still works but I rather replace the screen as the scratch is visible.
Where can I purchase the screen and replace it myself?
http://www.tmart.com/Replacement-LCD-Display-Screen-for-HTC-G19-Raider-4G_p137438.html
http://www.repairsuniverse.com/htc-vivid-screen-replacements-repair-parts.html
..
Thank you.
tap the thanks button
and good luck
A little advice - I've already replaced the screen on my Raider
Hi, glad someone else is attempting this. I had never replaced a screen in a phone before trying this so for me it was a little hair raising the first time I took it apart. On the back of the phone under the battery cover are 5 screws you need to remove, and one little plastic cover. Under the cover is the connector from the mainboard. Its just a little pop out connection, gently lever it loose before removing the shell to avoid hurting the ribbon.
Once you get this far, flip the phone face-up, and *from the bottom*, gently lever the sides and bottom of the plastic shell away from the screen. Its relatively easy.
Continue working along the edges toward the top until the plastic shell pops free, after that put it face-down again and remove the screws holding the battery holder to the rest of the phone. Pull it up and out to the left to remove it, being careful not to bend the battery contacts as they stay with the rest of the phone. Keep the screws with it, trust me - its easier to remember what goes where this way.
Once you have the battery holder off, put it aside and remove the screws holding the mainboard(s) to the shell. Also you will find three wires with little cup contacts at the ends, gently detach these as well, and when the screws and wires are off, carefully remove the boards. Look closely at the plastic tabs holding them in and you'll see how they come out. When taking them out of the phone you'll need to lift them like you were opening a book - ie. folding them to the right. Underneath are two sockets with ribbon cable connections, one should already be detached - the other can be popped off at this point. If you skipped detaching it at the beginning, now's the time to remove both.
This should leave you with two free boards attached in the middle by a black ribbon. Put them aside and what you have left in your hand is the metal shell, LCD, and digitizer.
NOW..the crappy news. This wonderful, beautiful, powerful, ESPENSIVE phone, is held together by black double-sided tape. Yep. Tape. AND you'll need some more before installing the new digitizer. I ordered mine from tmart as well and it not only comes with the wrong screwdrivers (btw you need a #1 philips bit - VERY tiny!!) but it doesn't come with any adhesive to mount the screen to.
Your new screen should also come with some prying tools, and they are quite handy. The guitar pick one didn't do much but the lever is very handy. You'll need to gently pry the digitizer away from the LCD with this tool being careful not to put too much pressure on the lcd or it might snap. Its only a few mm thick. GO SLOW.. you should have no problems. I've done it a few times now - I'm kinda rough on my toys.
Once you have the part un-taped, its still got the ribbon cable going back behind the lcd. Its connected to a small, thin socket on ther board. You lift a small white lever (remove the tape and save it - reapply it to the new connection) and slide the cable out. You'll need to use your lever again and pry up the lcd enough to slide the ribbon out from behind it. This can be tricky. Again, go slow, be real cautious..the tape is pretty strong. Once you have the panel out completely its just a matter of reversing the process. If you're real careful when removing the original panel, you might be able to reuse the double-sided tape thats in there.. I wasn't so lucky. Mine was covered in glass shards, as I mashed my screen pretty good.
Hope this helps!! I had a rough time the first time, but now its easy for me. I like taking it apart lol..
Let me know how you do! Good luck!
Brian
I have had this phone for about 1.5 years now and it held up,it was running very well but it always had an overheating problem,you have probably seen me all over the forums asking how can I lower the temperature of the phone lol.
Well it has become less apparent with the latest build of Lineage,only when I am using Snapchat but that doesn't matter.
But now what started happening is my back glass is unsticking,the bottom part to be exact,I believe this is because the device heated up so much it weakened the adhesive.
So I am asking now with what material I can re-stick the back glass properly since I don't want it to hang like that for no reason.
Use fevibond
You can use fevibond(Synthetic Rubber Base Glue). I used it to stick front screen peeling off from top left corner.
Dhgr8 said:
You can use fevibond(Synthetic Rubber Base Glue). I used it to stick front screen peeling off from top left corner.
Click to expand...
Click to collapse
Could I use something like superglue or something similar to that?
Dinkec27 said:
Could I use something like superglue or something similar to that?
Click to expand...
Click to collapse
No, that would make it tough/impossible to separate it for repairs.
Please refer to this thread https://forum.xda-developers.com/z3-compact/help/sony-xperia-z3-compacts-display-peeling-t3156347
Dinkec27 said:
Could I use something like superglue or something similar to that?
Click to expand...
Click to collapse
Nope I wouldn't do that, as super glue is not flexible. I have glued both screen and back glass with B7000 adhesive (most repair shops use it specifically for displays) and it hasn't moved since. That was done some 4 months ago. If you put enough glue on the frame (be careful not to leave empty spots, cover the complete frame with glue), of course avoid dripping of the sides into the frame, I am sure that it won't peel off again, especially the back glass.
I am waiting for new screen to arrive, so I'll have to re-do everything again, of course with B7000.
Dinkec27 said:
Could I use something like superglue or something similar to that?
Click to expand...
Click to collapse
Never use superglue, it will not last long and will ruin your phone, as superglue's main ingredient disintegrates plastic...
I've also used red 3m tape, does not hold!
Bought B7000 glue, will use it once my new battery arrives, so using useless 3m red tape in the mean time...
-Update-
B7000 Glue works!!!
I heavily flash, test etc. and no matter how hot the phone gets, it's sealed and does not reopen.
I cleaned the surfaces, I applied the glue, and did not care about making a mess (the glue is easily removable for future repairs) and did not care about it oozing out either, just made sure that it covered that border.
I did not use any heat, and it was still cold here.
I then used clothes pegs, 3 on each edge (I was worried about too much pressure, but it was not an issue)
I did not turn my phone on at all, and waited for 48 hours, before removing the pegs then turning it on.
Please note: the z3c is bendable, especially in jeans pockets, I use an anodized bumper to keep it straight. And using tempered glass on both sides is recommended.
***I did however buy a new battery, as my previous battery seemed fat, and I also removed the nfc sticker, but not sure if that is necessary.
Hi guys,
has anyone of you tried changing the front glass without digitizer and display?
In disassembly videos I can only see people changing the whole thing.
Also, do you think I can manage to repair the front glas as well as the USB port with just an iron instead of a hot air blower (and the usual tools made of plastic)?
Thanks in advance!
kadofl said:
Hi guys,
has anyone of you tried changing the front glass without digitizer and display?
In disassembly videos I can only see people changing the whole thing.
Also, do you think I can manage to repair the front glas as well as the USB port with just an iron instead of a hot air blower (and the usual tools made of plastic)?
Thanks in advance!
Click to expand...
Click to collapse
I haven't done the front glass on mine yet, but my understanding is that in general you're really better off replacing front glass as an entire unit with digitizer and display. An iron on pretty low through a cloth/towel might well work. It's not just glue that melts, it's a thin strip of rubber gasket material with adhesive (okay, maybe it's thick glue, but it looked pre-formed to me) holding the glass back cover on.
Heating probably helps a bit with softening the stuff, but after the first time you peel it up you won't really need to do that again. I'd recommend picking a corner (say, bottom left as you're looking at the back) and just plan on prying from there every time, so you only have one spot where the plastic gets marred.
Don't spend too much time heating, worry more about having a suction cup tool that you can lift with while you try to work a guitar pick or hobby knife or something in under the corner. Have at least two ready, so you can wedge one in, and work your way around without it just dropping back down on you. You'll probably tear the material a bit but that's okay, just spread it back out evenly around the edge on the glass before you put the cover back on. Also, you definitely should be using a case to make sure it doesn't just fall off in your pocket once you've opened it up a couple times.
USB cable replacement isn't awful, just time consuming. The biggest gotcha is to keep all three of the little gold clips on the plastic "mid frame" ring (that's the first thing you remove that requires screws after getting the back glass up) from fallling and getting lost.
You can PM me if you have any questions about this, I've replaced my USB cable/port assembly a couple times (first replacement was defective). And I'm about to attempt replacing the screen as a whole unit with glass & digitizer on my wife's Z2 Plus, so I'll let you know how that goes.