Related
I have installed the 1.12.10 GSM on it after making backups with aWizard. I am happy to report that it does work and that it does speed up the initial connection. Before (with 1.09.11 I beleive) I could log into (enter my PIN) and would still have some time before I would connect and get signal bars. It also seemed to increase refresh rates of the bars. Now the signal is usually found before I even finish entering my PIN muchless the today screen loading.
These tests were made in my basement at my house where I typically have been getting 1-3 bars. now to test 1.13.10 and 2.8 OS to see if it works.
I will say I thought it broke at first because I couldn't get my PC to talk to it after it reloaded, then I did another soft reset and the boot screen the second time didn't list the GSM version, even though the OS did see and use GSM. I re-ran the CID unlock procedure again since I could talk to the phone again. Reset again and GSM ver was on the boot screen again.
I also swapped out the boot screen for a bmp and that worked wonderfully. my only question is if there is a way to swap out the booting screen of the OS and not just the IPL Rom.
cheers,
ET
I have just done the RUU install of 2.16.9.101 which also upgrades IPL/SPL to 2.16. It changed my radio version to 2.7.10 and my protocol version is 413.1.0.3. This ROM date is 2/6/06.
Immediate differences are the battery notification is now at the top where on Cingular's ROM it was at the bottom next to the comm switch program. That and everything is I-Mate branded. No Get Good, but instead now I have I-Mate backgammon and Skype. And instead of the Cingular Mail link now there is an I-Mate mail link.
I will update later with more.
More... OS ver 5.1.195 build 14847.2.0.0 IDK if this is different or not.
Update 11AM: I have tested more. ZPhone themes I can't seem to install... IDK why but with the original Cingular ROM I couldn't either. The original ROM had a bug that used the proxy of the modem setting on the wifi setting making wifi not work unless you went and disabled it since it is enabled by default. This new rom after installing "Cingulcustomize_No_Emails.cab" to get MediaNet back, wifi just works. Even with the Proxy set on the modem connection. My Bluetooh headset (Jabra HT800) works great. Comm Manager is real nice. Even showing you the status of SMS and GPRS/EDGE connection. I want to play with it a little more to see if I can control those two or not. Gone from teh Cingular ROM is the ability to click on the Edge status icon in the notification area and tell it to turn on Wifi. But the Turn on Flight Mode still exists under the Cell Strength bar. Signal strength is comperable to the 1.12.10 radio rom I had before the upgrade. And IDK if it is taking longer to load from a reset or not, but before the Phone radio would be up and running just as I was finishing putting in my PIN unlock. But now it is running and connected before I can even start to input it. Just observation, that extra second doesn't mean anything.
I also have the 8125, so I am curious if the Imate ROM will cause any problems after the upgrade. I am not sure I want to wait a few more months until Cingular gets around to providing their upgrade.
Some other posters with the test/beta Qtek AKU 2.0 rom reported that they had trouble with the device resetting itself and problems with Wi-Fi. Let us know if you experience any issues with this ROM.
How has EDGE speed been, any improvements over the shipped ROM? Have you tried push email?
ok, i updated my 8125 to the new rom and am having two issues atm. first, the phone signal icon and the battery icon on the today screen is cut off so i only see the edge icon. secondly, i cannot start wifi at all, no matter what i do :\ (it looks like it's thinking but doesn't actually turn on ) now i did apply the cingular extended rom to this so i dont know if that caused both issues or not. as for edge performance, i'm in an area with bad signal so i couldnt exactly test it. i'm going to be clearing storage tonight and see if that fixes both issues or not. i haven't tested push e-mail as clubimates servers AREN'T supporting direct push (ie they don't have SP2 installed or have it enabled on exchange).
Locked up
Well I am noticing that it is locking up if I let it sit for a while to where I can't bring it back up. I have disabled the lock code to see if that fixes it.
I would have a feeling that the problems you are having are because of the enhanced rom difference. it won't hurt to try it as is like I did since you are having problems with it.
were can I fine install
I look for the rom in the ftp but there is no RUU install of 2.16.9.101 can you please tell me where can I fin this rom
thank you
Here:
http://forum.xda-developers.com/viewtopic.php?t=42638
Scroll down to HTTP server link.
Cheers
thanks
thank you for giving the info on where to get the link. I have been away from a pc today.
as an update: the phone seems to be stable with the new rom (I am actually using the phone now using edge and it seems faster than my old phone was which was a nokia.)
I haven't had it lock up on me since I uninstalled battery pack pro, disabled lock code, and uninstalled skype & backgammon so take your pick as to what fixed it. I will do some more expereriments to try and figure iit out.
later,
ET
Are you having the same issues as darkjedi who said he's having problems with WiFi and signal strength icon?
after the upgrade i cant find the GPS ICON
even i try to delete the redirect string in the registry like i used to do before
still i cant see the icon on my setting page
please anyone noticed this problem ?
tx
exchguy said:
Are you having the same issues as darkjedi who said he's having problems with WiFi and signal strength icon?
Click to expand...
Click to collapse
i finally fixed the signal strength icon (but don't ask me how), but wifi is still borked
no more problems, lock ups or otherwise
My guess with my problems were related to Battery Pack Pro demo. Even on the original rom I couldn't get it to work right with the assignable hard keys.
Anyway, I did not modify the original EXE one bit like darkjedi said he did. He seems to be much more advanced as I don't know how to do what he did and not that familier with its registry settings yet. But I naver had any problems with Wifi nor with icon placement.
My home wifi does use WPS-PSK TKIP using a Netgear WG302. Battery life seems good, but I do get a little crackle every now and then on my end of the bluetooth handsfree. People I talk to haven't said they hear anything other than perfect clarity. I would have been told if they heard anything since part of my reason to spend the money now rather than later was my voice and signal quality on my old Nokia was getting to be bad and they wouldn't waste a second ragging me if voice and signal problems were re-appearing. But mostly the crackle is few and far between and usually when my headset is on the other side of my body or I am a few feet away from my phone.
i didn't modify the original EXE, i installed it as normal, then after the fact, copied the cingular extended ROM then installed each cab manually. i didn't get a chance to try wifi before i applied the extended rom, but i just might hard reset and try that.
i dnt see the rush to upgrade if u have a cingular 8125 since there goa offer rom upgrades for the unit. with all the bugs i rather just get a ad2 bt plugin (wish they made it) and just do that
what roms do they offer? On my past phones I have had to have major problems before they would flash a new version of the Rom (my last 2 symbian phones).
darkjedi said:
i didn't modify the original EXE, i installed it as normal, then after the fact, copied the cingular extended ROM then installed each cab manually. i didn't get a chance to try wifi before i applied the extended rom, but i just might hard reset and try that.
Click to expand...
Click to collapse
ok... the only cab I installed for Cingular was the one I mentioned earlier. I have since installed spb power plus and their weather app and I am still stable. Not one failuer and my bluetooth is actually acting better from some reason. I was working on my car today with teh phone in the car and I was about 10 feet away without any noise or other problems.
Re: thanks
ethorn said:
thank you for giving the info on where to get the link. I have been away from a pc today.
as an update: the phone seems to be stable with the new rom (I am actually using the phone now using edge and it seems faster than my old phone was which was a nokia.)
I haven't had it lock up on me since I uninstalled battery pack pro, disabled lock code, and uninstalled skype & backgammon so take your pick as to what fixed it. I will do some more expereriments to try and figure iit out.
later,
ET
Click to expand...
Click to collapse
Is there any settings to configure edge? I only see GPRS in the connections section.
This version appears quite stable but's only my second day since upgrading my 8125 from the QTECH 2.8.7.102. I really like the Comm manager and the Push Email icon works great.
Thanks!
name of account
the only thing that I have notice so far is that the name of my celular company (I could see before upgrade) now i only see numbers.
exchguy said:
I also have the 8125, so I am curious if the Imate ROM will cause any problems after the upgrade. I am not sure I want to wait a few more months until Cingular gets around to providing their upgrade.
Some other posters with the test/beta Qtek AKU 2.0 rom reported that they had trouble with the device resetting itself and problems with Wi-Fi. Let us know if you experience any issues with this ROM.
How has EDGE speed been, any improvements over the shipped ROM? Have you tried push email?
Click to expand...
Click to collapse
On the new imate ROM I'm getting between 65 and 110 kbps on edge. Latency is still crap at about 1.5 seconds on average, but that's what it's always been for me.
Direct push is great. Assuming you have Exch SP2 installed, push works without any other changes. I'm averaging between 7 and 10 seconds for an entry to push out after it gets to Exchange. I haven't installed the device management tools yet, but I'll do that soon and let you know how well they work.
I just noticed wifi isn't working. If I enable it in comm manager, the button is ringed in green as if it's on, but the left green led does not blink and it does not detect my open, unsecured access point. I did install the cabs from my original cingular extended rom, and one of those appears realted to wifi, but not sure what it does. I'll mess around some more and see what I can do. I'm not totally heartbroken that wifi is messed up, but it does bug me that I don't know why it aint working.
Need Cingulcustomize_No_Emails.cab file
ethorn said:
I have just done the RUU install of 2.16.9.101 which also upgrades IPL/SPL to 2.16. It changed my radio version to 2.7.10 and my protocol version is 413.1.0.3. This ROM date is 2/6/06.
Immediate differences are the battery notification is now at the top where on Cingular's ROM it was at the bottom next to the comm switch program. That and everything is I-Mate branded. No Get Good, but instead now I have I-Mate backgammon and Skype. And instead of the Cingular Mail link now there is an I-Mate mail link.
I will update later with more.
More... OS ver 5.1.195 build 14847.2.0.0 IDK if this is different or not.
Update 11AM: I have tested more. ZPhone themes I can't seem to install... IDK why but with the original Cingular ROM I couldn't either. The original ROM had a bug that used the proxy of the modem setting on the wifi setting making wifi not work unless you went and disabled it since it is enabled by default. This new rom after installing "Cingulcustomize_No_Emails.cab" to get MediaNet back, wifi just works. Even with the Proxy set on the modem connection. My Bluetooh headset (Jabra HT800) works great. Comm Manager is real nice. Even showing you the status of SMS and GPRS/EDGE connection. I want to play with it a little more to see if I can control those two or not. Gone from teh Cingular ROM is the ability to click on the Edge status icon in the notification area and tell it to turn on Wifi. But the Turn on Flight Mode still exists under the Cell Strength bar. Signal strength is comperable to the 1.12.10 radio rom I had before the upgrade. And IDK if it is taking longer to load from a reset or not, but before the Phone radio would be up and running just as I was finishing putting in my PIN unlock. But now it is running and connected before I can even start to input it. Just observation, that extra second doesn't mean anything.
Click to expand...
Click to collapse
Where did you get the "Cingulcustomize_No_Emails.cab" file? I have searched everywhere and cannot find it! Help?
1.40.00 with radio 1.12.00 (This was actually whay my device was shipped with. I chose the wrong version when downgrading from wm5.
Anyway, my problem is that with old version of 1.22 I was able to use the internet using t-mobiles proxy settings of 216.155.165.50 port 8080. I made the exact same changes to my settings in the upgraded OS but I cannot browse anywhere. The only thing I can do is use AIM on port 25 but want to be able to access the internet.
Any idea on what's going on? Because I don't want to downgrade again because I want to keep Media player 10 and have mp3 ringtones.
phone support!
Hi, I just phoned support (which is 2828 for t-mobile-Business customers don't know whats yours). And they just gave me some settings I had to make (including atwo letter password) and it worked out fine (sorry Ive not got my blueangel here by now, cause its in the IT-Dept for setup of "messaging and security services" for pushmail with Exchange 2003SP2 - so I can not tell you the settings from my mda and I also have not memorized them in a way to tell them from mind).
Actually I did NOT tell the support that I flashed anything, but told them that my settings got lost.
So I'm now using Ivans ROM with some additions from TuMa1.4 and still have GPRS-Internet-Connection. The Internetconnection through Active-Synch (for e.g. AvantGo) works as well (but the latter did also without asking support)
I have upgraded my active synch to the 4.2 beta and even that works better than ever.
So I can just recommend "ask support"
I tried asking support. As usual, instead they just said it cannot be done and that I would have to upgrade to the 29.99 package which I am definitely not doing. I really need to find those setting you received.
Do you need to use the proxy on T-Mobile? If you are getting AIM through then you have connectivity to the net. The only thing holding you back would be if they blocked port 80 outbound and forced you through a proxy. My Orange GPRS doesn't need one.
Have you checked the "programs connect to the internet / work using:" settings? AIM probably ignores them, so that might be an issue.
Hi,
I've been using this forum for a while but think this is my first ever post!
I've been having problems with the search function today so decided its going to be quicker if someone can help me out.
I've never updated the rom on my wizard (which was on o2 but i unlocked and usign t-mobile uk sim now) though as im using push email the not vibrating when on standby thing is starting to piss me off.
Question is which rom do i need to fix that standby problem?
currently mine is on
rom version: 2.21.4.1 WWE
date 3/9/06
radio version 02.07.10
protocol version 413.1.03
extrom version 2.21.4.101
bit of a begginer with this so not sure if its g3 or g4 :S
thanks for any help
You can use my Molski.Biz roms.
Never heard that someone that uses my Rom has the same problem like you.
Regards,
Molski
have you tried going to settings, sounds and notifications, then tick the notifications tab at the bottom, under Event choose Messaging: New Email message then tick the option for vibrate?
dont know if this works while in standby or not, but know the option is there and turned off by default
yeah its set to make a sound and vibrate etc... which it does when its on, just in stand by it doesnt do it.
Heard about the problem before tbh which is how i know its a romproblem.
Just downloaded the t-mobile usa rom which imgonna give a blast, nothing to loose i guess
ahh had a go late last night and learned a few more things which if id spent longer reading the forum id have found out lol.
Right my phones a G4 and was an o2 uk phone.
First problem was it seems impossible to update a rom in vista as when it goes into bootloader mode vista disconnects from the phone. had a go with xp and got further.
Next problem is seems I can only use o2 uk roms presumably due to it being CID locked which am i right in thinking you have to pay to unlock?
Sooo if I want a nice new rom am I right in thinking im buggered? lol
7 radio ROM exist for our HIMALAYA -
http://buzzdev.net/index.php?option=com_remository&Itemid=132&func=select&id=26
My experience -
1.08 - Modem not ready sometimes for GPRS > need Off/On radio. Faster discharge battery ?
1.17 - Phone not reply (inaccessible) for incoming talk sometimes > need Off/On radio.
1.19 - Off/On radio (flight mode) is very slow or imposible.
which one is the most stable?
Im trying now 1.14.
Radio 1.19 is so far so good for me.
1.17 works good on my HIMALAYA(TOFCLOCK)~
signal problem
Now I`m using 1.18 .
With my experience with my device , this radio version is very bad . sometimes the signal strength lost / blank . Huhhh
I`m tired with my device .
Anyone can solve the signal problem ?
with change the radio version or what !!!
Thanks
I am still using radio version 1.08 and this is working fine for me,
Best Regards
Im still running 1.08 too but not stable enough. Will try others soon....
Hmm, right now I'm using 1.18 (were using all of them already).
Signal is good, and right now battery is 18% and I'm still able to talk, without any voice quality drop.
Still, can't return from airplane.
Hi,
Is it possible to turn the flight mode off from the wireless manager. I do not seems to be able to do that with radio rom 1.18. With radio 1.08 it was possible. Well I will use with radio rom 1.18 for a few days to see if it is stable.
Hi, having the same annoying bug for radio roms 1.17, 1.18 and 1.19 - after a reset (hard or soft) I see gsm network signal for some time (from 1 sec to 3-4 hours) and then it disappears, and there's no way to make the phone get operating again. I'm still trying the 1.08, and it seems not to have any strange behaviour... it does the same with WM2003, 2005 and 2006.
I really do not care about the battery, as long as I can receive calls so as for now, I'll keep the 1.08...
so.... it's not a bug. It seems you have a broken radio or some really old hardware? Don't know. It's PH10B, right?
@utak3r could you explain me more detail about PH10B concerning its capability. It must be good knowledge for us. Thank in advanced. Also if you have a way how to improve the performance, indeed not to change the PDA with the new one
I contacted SosTekIt, which released an Italian rom based on WM2005, and he was of the same opinion; but, in WM2005 I'm still trying with the same SIM card, I have no issues at all.
Yes, the board is PH10B, and the strangest part ever is that in WM2006 if I can make a call in the few seconds I see the signal, then the phone is fully functional, even for HOURS. But when I roam out of the gsm cell, the signal disappear.
Truly, this is freaking me out
Well, I can believe you...
This is really strange, and as for now I can find no explanation for such a behaviour. Will try to think about it, but... oh well.
Some more details...
1. Same strange behaviour in WM2005 (buzz rom)
2. The "Preferred Networks" (Settings -> Phone -> Network -> Set Networks) list shows that my mobile operator is always the last, unchecked. I modify the list, update the settings, and they keep existing until I get out of GSM cell.
3. When awakening, if the phone shows the G icon of GPRS, then it locks to the signal and never looses.
Hi
I havent performed any upgrades to my XDA2i (official or otherwise) for at least 3 years - are there any upgrades I should consider?
Here is my Device Info
ROM Version : 1.11.00 WWE
ROM Date : 01/27/05
Radio Version : 1.00.00
Protocol Version : 1337.39
ExtROM Version : [THIS IS BLANK]
Model Number : PH10C
Also, I am unable to connect to WiFi with my XDAIIi
The device finds wifi signals and sometimes will make a connection - but when I try and open a webpage I get a screen showing "IIS7" and nothing else.
Here are my settings for WiFi :
Network Card Connects to tiacxwin Campatible Wireless Ethernet (for both The Internet and Work).
Power Save slider is set for Best Performance.
Thanks for any help and advice !!!
Paul
I am in a similar position Paul.
I have been given a 02 XDAll by my company to use for recording surveys.
Its bog standard like yours.
I'd really like to upgrade it but the problem is there is almost too much written about it on these forums .Most of it is so old and out of date that all the links are broken. Its hard work trawling through it.
What is needed is a simple basic upgrading overview listing all the options but I suppose everyone has moved on to more recent PDA's and are no longer interested in these
I've posted a similar request in the Himilayer section .Maybe we can share what we find
Nick
Nick, do you have a Himalaya or an Alpine? PH10B or PH10C?
The Alpine is stuck on WM2003, perfectly good for its task just not upgradeable to WM5 or WM6.
As for customising it realy depends what you are looking for.
Hi DeeDee thank you for responding. I feel guilty hyjacking Paul's thread.
Mine is a Himalaya 10B
with following spec
02 XDAll
2Gb SD card
Rom 1.72.00WWE
Date03/15/04
Radio 1.17.04
ext Rom 1.72.18.1
Ram 128Mb
Model PH10B
I just wanted to improve the Active page if its possible .I cannot read the tiny text so large button icons like the Diamond would be useful
I cannot set the Internet access up either ? have tried for hours.
I have a Netgear Wireless Modem router DG834G but neither the manual or quick guide explain how to set up the XDA .
I have spent several days trawling this site and the net.
Any help appreciated thank you
Nick,
No problem joining in - if we can get the WiFi problem sorted I would be more than happy.
DeeDee,
Should my ExtROM Version be completely blank?
Thanks
Paul
Hi Paul
you're up early !
I have used WM5 on an XDA Mini S (Wizard) a couple of years ago. I imagine that most of the current software and apps are written for WM5 orWM6 so it will mean I'll need to upgrade to WM6. Presume that means flashing the Rom which judging by the number of disasters on this forum is not something I'd do lightly.
Particularly as there are virtually no answers to requests for help.
I found a statement last night that basically says unless you are a software developer you arn't welcome on this forum which probably explains the lack of help.
Yours has the 128 Rom as apposed to my 64Mb which is a big advantage. I have gone off the idea of buying a Himalaya or an Alpine as they are too antiquated really which is a shame as I love the build quality and screen size.
I'm going to look for something a bit more contemporary I think . In the mean time I'll enjoy using the works XDA ll
Hi
Flashing the Himalaya to WM5 or WM6 is painless and it has to be said slightly addictive, you will try many ROMs until you find one you like. Think I have tried most of the ROMs for the Himalaya.
The lack of help has NOTHING to do with not being a developer, i'm not one and have had lots of help. The problem is probably due to the lack of people using these PPCs. i have to confess my Himalaya is purely there as something to muck about with, work didn't want it any more. i have a Trinity as primary PPC phone and an Alpine with an application that doesn't work on WM5.
You won't get your Himalaya to connect to your WiFi as it doesn't do WiFi without an add on card.
DeeDee,
Should my (Alpine) ExtROM Version be completely blank?
Thanks
Paul
Hi Paul
Can't remember and my Alpine is at home, but i don't think so.
deedee said:
Hi
Flashing the Himalaya to WM5 or WM6 is painless and it has to be said slightly addictive, you will try many ROMs until you find one you like. Think I have tried most of the ROMs for the Himalaya.
The lack of help has NOTHING to do with not being a developer, i'm not one and have had lots of help. The problem is probably due to the lack of people using these PPCs. i have to confess my Himalaya is purely there as something to muck about with, work didn't want it any more. i have a Trinity as primary PPC phone and an Alpine with an application that doesn't work on WM5.
You won't get your Himalaya to connect to your WiFi as it doesn't do WiFi without an add on card.
Click to expand...
Click to collapse
Thankyou DeeDee I appreciate you taking the trouble to answer silly questions by a noob.
I have downloaded and printed out a 140 page manual and there was nothing clear about connecting to wi-fi
If I have to carry this Hima around with me all day I might as well have it working as well as it can.I had intended to purchase a 3g Iphone for myself but now I'm not so sure I might buy a HTC instead if I can find one with 3.5" screen and wi-fi and a reasonable interface like touchflo
Nick
i have to say the smaller screen on my Trinity is perfectly adequate and that the larger form factor of the Alpine/Himalaya means you need a headset/handsfree kit to really use it as a phone.
It's also not pocketable, which my Trinity is, just.
If you can find a decent mobile shop and have a touchy feely sesion with as many as you can.
thanks DeeDee thats excellent advice. Photos never give a good indication of size and ease of use . The size is a bind like you say its heavy and too big for a shirt pocket but it is easier for me to work with using reading glasses.
I got an 02 XDA mini S when they first came out. I found the screen too small and fiddly and it stayed in the box unused for 18 months when I sold it on ebay for nothing so I have learnt my lesson.
DeeDee may I just ask one other question please. I have trawled through the wiki and various other sources but I still haven'y founf an answer to my initial question on the Himalaya board.
Q1 How do you install a new app on the Hima or Alpine ?
Q2. where does it get installed to ?
Today we lost the special survey App again Grrrrrrrrrrrv because the flippin battery went flat.
My boss is hopping mad and blames me !....I blame IT cos they installed it.
There must be somewhere we can install an App to that is non volatile and is not lost every time the battery goes flat.
Presumably the same place that WM2003 is installed ? How is it done ?
To install an app either:
1 - use Active Sync to install it if necessary
2 - if the install is a CAB file copy it to a memory card and then click it on the PPC to run the install.
As for the where it installs, when you run the installer it may ask where you wish to install, either Device/Storage Card. Make sure both batteries are charging. In all honesty it's not your fault that the end users aren't charging their Alpine on a regular basis.