Database Develop

SOLUTION FOUND -CID/sim UNLOCKING FOR WIZARD WITH AKU2 ROMS.

warnning; does not work with g4 wizards!!!!!
this steps are to cid unlock and also to unlock sim in the folowing devices; qtek 9100, i-mate k-jam, mda vario, orange spv m3000, o2 xda mini s, dopod 838, Cingular 8125
first; you must make a full backup of you wizard before doing this , I personally use [wizBackup.exe] posted below for my backups and restores. This is not mandatory but could save an enormous amount of trouble.
I as most people with a wizard with the aku2 rom found out that it cannot be cid unlock with lokiwiz tool, you will get the following;{error:itwritedisk-an internal error occurred}.
. that is till now.
downgrade rom here http://dl.dropbox.com/u/7696581/htc%20wizard/CUSTOM__RUU_Wizard_1050412_WWE_101_11210_WWE.exe
note- this steps is for unlocking the cid of the wizard with aku2 rom.
how to cid. unlock all wizard variants ( that have the latest rom build )
first download custom__ruu_wizard_1050412_wwe_101_11210_wwe. rom from the ftp site from the above link, unpack it and just click the romupdateutility_wizard_noid.exe to start downgrading. Simply follow the prompts.
after the rom are loaded go thru the initial setup as you would with any rom.
now download the (lokiwiz02b) from here;
http://dl.dropbox.com/u/7696581/htc wizard/CUSTOM__RUU_Wizard_1050412_WWE_101_11210_WWE.exe
Make sure you unzip lokiwiz to the root o the c: drive.
please copy the whole lokiwiz folder to the root of the drive,not the contentents of the folder!!!!!
and follow the instructions .do not forget to copy the cab file(enable rapi) to your device and run it before running lokiwiz.
Now run lockiwiz and unlock your machine, your machine will reboot itself. if yoy see an eroot while unlocking that says;
..............................................................................................................................................................................
CopyFileToTFFS(cidunlocked.bin:0, 0, 00010000)
ERROR: ITWriteDisk - An internal error occurred.
this means that you device not been unloked......try again............
.................................................................................................................................................................................
That’s it your wizard is unlocked. Make sure yew keep the [lock_backup.bin] in a safe place you may need it for guaranty purposes.
Now flash the latest aku2 rom from your provider.- [very important,to avoid future problems wit rom updates]
then u can flash any rom you want.
question: if i cid unlock and sim unlock my phone (after installing custom 1.5 wwe rom) and then i install latest aku2 i-mate italian rom, will the sim unlock (and cid one too) be preserved?
Answer: i can confirm that that upgrading to the latest aku2 rom the wizard remains cid unlocked.
Special thanks to the author of the above cooked rom [button] also to machinagod for the lokiwiz tool and joninla for finding the downgrade rom, molski for is input and everyone that contributed to the cause.
do not try to downgrade using an older wizard rom other than the one posted above it will not work
also this {how to} is for the htc wizard only it may work with other devices but i don’t know, so if you turn you device into a brick do not blame me. use it at your own risk
if you device is from a operator like: 02, orange etc... You will void your guaranty unlocking cid, but don’t despair, if you keep the [lock_backup.bin] file that the lockiz tool generated you can restore cid to factory default.
this proccess only needs to be done once in the wizards lifetime.
Enjoy;
Jose faria.
donate if you like my work

Faria, can you tell me if this process will do it for the HTC Prophets with rom 2.x ???

I've got an imate JAMin with aku2 from factory. Just downloaded older Imate Rom... will try the process when i get home
8) wish me luck

maybe if you find an older rom for you device i only have a wizard.take a look at the lokiwiz tread i belive tha someone mentioned the HTC Prophets.

jamichy said:
I've got an imate JAMin with aku2 from factory. Just downloaded older Imate Rom... will try the process when i get home
8) wish me luck
Click to expand...
Click to collapse
Bet I will!!
For the record, your Jamin's rom is the same that was available to download some weeks ago with the Aku2??

jamichy said:
I've got an imate JAMin with aku2 from factory. Just downloaded older Imate Rom... will try the process when i get home
8) wish me luck
Click to expand...
Click to collapse
let me know how you get on.

onesolo said:
Faria, can you tell me if this process will do it for the HTC Prophets with rom 2.x ???
Click to expand...
Click to collapse
it may be possible,if you have an old custom rom for your device ,found this;
On the one hand, HTC Prophet is a complete copy (both software and hardware are meant) of HTC Wizard. On the other hand, it's equal to HTC Magician in appearance. That is why today review will be quite short, we will only discuss external elements and a new camera, all other aspects were highlighted in the review of HTC Wizard.
http://www.mobile-review.com/pda/review/htc-prophet-en.shtml

Hi Faria, thank you for your HowTo!
Now i know the wizard remains CID unlocked after the upgrade and that's good. I only hope that it stays SIM unlocked too.
Bye

Sadly, cant move back to older rom... keep getting error message saying the nk.nbf file is not valid/older than your current file.
I guess we just have to wait for an updated version of Lockiwiz

sh*t forgot to post the address to the downgrade rom.here it ftp://xda:[email protected]__RUU_Wizard_1050412_WWE_101_11210_WWE.exe
sorry guys

jamichy said:
Sadly, cant move back to older rom... keep getting error message saying the nk.nbf file is not valid/older than your current file.
I guess we just have to wait for an updated version of Lockiwiz
Click to expand...
Click to collapse
yes u can, use this rom to downgrade
ftp://xda:[email protected]__RUU_Wizard_1050412_WWE_101_11210_WWE.exe

faria said:
jamichy said:
Sadly, cant move back to older rom... keep getting error message saying the nk.nbf file is not valid/older than your current file.
I guess we just have to wait for an updated version of Lockiwiz
Click to expand...
Click to collapse
yes u can, use this rom to downgrade
ftp://xda:[email protected]__RUU_Wizard_1050412_WWE_101_11210_WWE.exe
Click to expand...
Click to collapse
Hello, could you please tell me what is changed in the custom ROM???
I am willing to do the same thing for the prophet.
Thanks

nothing except i did not post the link to the rom by mistake,did you use an old i-mate rom to downgrade? do not it will not work, use the one in the above link.thats the only one that it will work that a know for sure.

faria said:
nothing except i did not post the link to the rom by mistake,did you use an old i-mate rom to downgrade? do not it will not work, use the one in the above link.thats the only one that it will work that a know for sure.
Click to expand...
Click to collapse
You mean to use the wizard rom on the prophet?
Won't that overwrite the bootloader with the one for the wizard???

andrew_sh said:
faria said:
nothing except i did not post the link to the rom by mistake,did you use an old i-mate rom to downgrade? do not it will not work, use the one in the above link.thats the only one that it will work that a know for sure.
Click to expand...
Click to collapse
You mean to use the wizard rom on the prophet?
Won't that overwrite the bootloader with the one for the wizard???
Click to expand...
Click to collapse
haaa you have the prophet
dont do that it may turn the prophet into a brick the only way is to find an old custom rom for your device. take a look at the ftp site it may have one there.
sorry

I told you Faria that it can be done
Great that it worked out okay, I can imagine how happy you are feeling right now
Nice how-to by the way.

mm..i am currently using T-mobile MDA Vario with the original rom
is that mean i don't have to apply it to unlock the cid?
i just use the lokiwiz 2b to unlock the CID, after it, even i upgrade to the newest rom e.g. the new O2 rom, my CID still remain unlock?

siupiu said:
mm..i am currently using T-mobile MDA Vario with the original rom
is that mean i don't have to apply it to unlock the cid?
i just use the lokiwiz 2b to unlock the CID, after it, even i upgrade to the newest rom e.g. the new O2 rom, my CID still remain unlock?
Click to expand...
Click to collapse
THATS IT.

siupiu said:
mm..i am currently using T-mobile MDA Vario with the original rom
is that mean i don't have to apply it to unlock the cid?
i just use the lokiwiz 2b to unlock the CID, after it, even i upgrade to the newest rom e.g. the new O2 rom, my CID still remain unlock?
Click to expand...
Click to collapse
THATS IT.

good, really thx~~^_^

Do I need to CID unlock my wizard?

Hi
I am sorry to ask this stupid question, I know its been discussed a lot of times but please help me understand it.
I am using Dopod 838 with Mr. Clean ROM and this is how IPL/SPL look like in my device:
IPL 2.24
SPL 2.24
GSM 02.25.11
OS 2.24.10.1
Now I want to upgrade to Molski's AKU2.3 ROM at
http://forum.xda-developers.com/showthread.php?t=282498
These are my questions:
- Do I really need to CID unlock dopod 838 to install it? Last time when I flashed Mr. Clean ROM, I didnot really do CID unlock, why do I need it now?
- what happens if I go ahead and install this ROM without CID unlocking my device?
greatly Appreciate your help.

if you know it has been discussed before why not search for the answer, either here or google it. i'm a newb as well i don't know everything so i can't help but the search feature is your friend. or you can be like some of the other newbs and just try it and possibly brick your phone your call

sasa123 said:
Hi
I am sorry to ask this stupid question, I know its been discussed a lot of times but please help me understand it.
I am using Dopod 838 with Mr. Clean ROM and this is how IPL/SPL look like in my device:
IPL 2.24
SPL 2.24
GSM 02.25.11
OS 2.24.10.1
Now I want to upgrade to Molski's AKU2.3 ROM at
http://forum.xda-developers.com/showthread.php?t=282498
These are my questions:
- Do I really need to CID unlock dopod 838 to install it? Last time when I flashed Mr. Clean ROM, I didnot really do CID unlock, why do I need it now?
- what happens if I go ahead and install this ROM without CID unlocking my device?
greatly Appreciate your help.
Click to expand...
Click to collapse
Answers: 1)Yes 2)you probably end up with a brick--and not the kind you can build with but the kind that breaks a window well when you throw it.
--M

^^^ hahahah LOL

demontefixo said:
Answers: 1)Yes 2)you probably end up with a brick--and not the kind you can build with but the kind that breaks a window well when you throw it.
--M
Click to expand...
Click to collapse
LOL
Thanks for the reply. ok, so I need to CID unlock. But I still wonder, why I did not need to CID unlock it when I flashed Mr. Clean rom.
And in Faria's CID unlock instructions, I have a doubt. Once I downgrade ROM to 1.x and unlock, do I flash Mr. Clean ROM first and then to Molski's ROM? or I can directly flash to Molski's after downgradin to 1.x ROM.

Simple answer is that Mr Clean's ROM does not contain the bootloader that is the IPL/SPL bit ok.
Riptos

riptos said:
Simple answer is that Mr Clean's ROM does not contain the bootloader that is the IPL/SPL bit ok.
Riptos
Click to expand...
Click to collapse
I think it does contain because it changes the IPL/SPL after upgrade and including start up screen

If you are CID locked you WILL NOT be able to flash any other ROM other than your vendor supplied ROMs UNLESS it does not contain the bootloader (IPL/SPL).
Riptos

Mr. Cleans does the CID unlocking bit for you if i am not mistaken...
But just to be sure, just do another round of CID unlocking procedure to make sure it's really unlocked...
Dr. Puttingtam's instructions seems to work fine with anyone's who did it correctly.
Molski's ROM do contain IPL/SPL, but they are for G3 Wizards only...To be sure that you had the correct bootloaders, try flashing to the last T-Mobile US ROM (the 2.26 version), set Active Sync to guest mode and then flash Molski's ROM...
Hope it goes fine with you

vseehua said:
Mr. Cleans does the CID unlocking bit for you if i am not mistaken...
But just to be sure, just do another round of CID unlocking procedure to make sure it's really unlocked...
Dr. Puttingtam's instructions seems to work fine with anyone's who did it correctly.
Molski's ROM do contain IPL/SPL, but they are for G3 Wizards only...To be sure that you had the correct bootloaders, try flashing to the last T-Mobile US ROM (the 2.26 version), set Active Sync to guest mode and then flash Molski's ROM...
Hope it goes fine with you
Click to expand...
Click to collapse
Thanks vseehua. I guess I am clear now. Will try it this weekend and will let you know how it goes. Thanks again to all for your comments and suggestions. I hope I dont brink it

Small question...Aam i ready to upgrade my rom ?

i want to flash the Molski.Biz AKU3.3 Crossbow Style Edition Rom...i have a IPL/SPL both of 1.05....and the phone is unlocked....am i ready to flash this rom ?? if not what pther things must i do first....i have read through all the threads but the IPL/SPL part is confusing me

first is to determine wether your device is G3 or G4..
in your case.. you have a G4 device.. (i just sense it with my 3rd eye..lol)
because looking at your IPL/SPL version.. you have 1.05 meaning G3..
For me.. You are now ready to upgrade.. BUT! YOU"RE NOT READY to upgrade any radio rom that has version 2.xx, you can only have radio version that has 1.xx version..
becouse your bootloader is 1.xx
Upgrdae your IPL/SPL version to something 2.xx to be able to upgrade your radio rom to 2.xx
Do i make my statement clear?

double_ofour said:
in your case.. you have a G4 device.. (i just sense it with my 3rd eye..lol)
because looking at your IPL/SPL version.. you have 1.05 meaning G3..
Click to expand...
Click to collapse
is my device a G4 or a G3 ? u kinda contradicted urself accidently in ur post....iam guessing its a G3...am i right ?
double_ofour said:
Upgrdae your IPL/SPL version to something 2.xx to be able to upgrade your radio rom to 2.xx
Do i make my statement clear?
Click to expand...
Click to collapse
ok now this part i DONT get...how do i upgrade the IPL/SPL ?? is there a special ROM for that ?

ooppss.. sorry..
i was in a hurry typing thats why i typed it misspeled..
YOU HAVE A G3 DEVICE..
regarding to your second question..
i myself dont have much knowledge about IPL/SPL..
but as far as i know..
newer IPL/SPL version are already included in some ROM.. like underground?.. (i think)
and.. for that to work.. you must first have your CID Unlocked..
(Correct me if im wrong experts.. but thats what i know..)

Dr puttingham said to me before that..
"I suggest the T-Mobile 2.26. In my tutorial you'll find the working link."
He said that to me if you want to upgrade your IPL/SPL..
you have to be CID Unlock first..

double_ofour said:
Dr puttingham said to me before that..
"I suggest the T-Mobile 2.26. In my tutorial you'll find the working link."
He said that to me if you want to upgrade your IPL/SPL..
you have to be CID Unlock first..
Click to expand...
Click to collapse
but doesnt the fact that i have a 1.05 SPL/IPL mean that my CID is unlocked ??

ranasrule said:
but doesnt the fact that i have a 1.05 SPL/IPL mean that my CID is unlocked ??
Click to expand...
Click to collapse
ok my device IS CID unlocked....bnecause i can use any SIM i want...just tried 3 different company's SIMs
OK SO NOW THE QUESTION IS....which ROM to i install to upgrade the IPL/SPL and is this even necessary if i want to flash the Molski.Biz AKU3.3 Crossbow Style Edition Rom

CID is not SIM
ranasrule said:
ok my device IS CID unlocked....bnecause i can use any SIM i want...just tried 3 different company's SIMs
OK SO NOW THE QUESTION IS....which ROM to i install to upgrade the IPL/SPL and is this even necessary if i want to flash the Molski.Biz AKU3.3 Crossbow Style Edition Rom
Click to expand...
Click to collapse
I don't want to confuse you, but SIM unlocked is not the same as CID unlocked. Please check one of the sticky posts for ways to CID unlock your phone!

mr-who said:
I don't want to confuse you, but SIM unlocked is not the same as CID unlocked. Please check one of the sticky posts for ways to CID unlock your phone!
Click to expand...
Click to collapse
ok thanks fior the info.....so is there any way to verify weather my device is CID unlocked ? what if i try to unlock an already unlocked device ? will that leave me with a very expensive brick ?

Unlocking again doens't hurt
ranasrule said:
ok thanks fior the info.....so is there any way to verify weather my device is CID unlocked ? what if i try to unlock an already unlocked device ? will that leave me with a very expensive brick ?
Click to expand...
Click to collapse
AFAIK there is no easy way to tell whether you have an CID unlocked phone. But the good thing is, you will NOT brick you device by unlocking an already unlocked phone. So just give it go!
Succes!

yup yup..
i agree..

EVERY HERALD.be carefull.please do read this.

I had seen the Aserg using he USPL to flash his rom and radio.
GUYs:
DO remember,if you are not Hard-spl,your spl ipl is lower than 4.00.0000,Please don't run JUMPSPL or USPL-BETA3 by pof.
Trust me or you will find lots of bricks on street.
Click to expand...
Click to collapse
If you are HTC 4350 OR VADEFONE OR T-WING.run official ruu update to WM6 frist,to make you IPL SPL upon 4.00.0000
If you think I am joking.keep on..
Click to expand...
Click to collapse
check more here or here

And if ipl/spl: 5.04.0001/5.04.0000 from WM5??? That is possible?

ASerg said:
And if ipl/spl: 5.04.0001/5.04.0000 from WM5??? That is possible?
Click to expand...
Click to collapse
that's ok. nothing at all.
safely.

Now I shall check up

I confirm. Thanks!

ASerg said:
I confirm. Thanks!
Click to expand...
Click to collapse
please warn people in your post.
and why don't you use jspl.it's quick and safely.uspl too slow but simply use

i want to be able to flash my rom so that i could install the HTC RUU on my tmo wing ( it's actually a herald but i was stupid enough to put in the TMO RUU)
Do you know any way i could do that with instructions available?
Also, once i do it, would the phone become unlocked again or still locked Just wondering.

umchriswho said:
i want to be able to flash my rom so that i could install the HTC RUU on my tmo wing ( it's actually a herald but i was stupid enough to put in the TMO RUU)
Do you know any way i could do that with instructions available?
Also, once i do it, would the phone become unlocked again or still locked Just wondering.
Click to expand...
Click to collapse
The HARD-SPL is a little more dangerous than the USPL... I can help you find ways to get any ROM you want on that phone easily enough, but UNLOCKING it again is the hard part. There's not 100% sure fire SAFE way of doing it.

welll, i just installed the hard-spl on my device and it went through
there's just one thing that gets me...
what's the difference with this hard-spl and HTC?
is the only difference is that the boot screen is different or are there more features?
For now, I just need a comparision of what the hard-spl has from the HTC one.

The Hard-SPL is a customer SPL. It's permanent, too. You will have to create your own customized RUU from now on, one that lacks the SPL. You can't flash RUU's that contain SPL because the SPL is now write protected. It's convinient, though, because now you can't accidently screw it up. (It's safe once you have it IN your device. Too many people brick their phones trying to get it in there in the first place, though.)

So now i won't be able to put in the HTC RUU anymore?
All right, sorry i'm being so stupid, but here's another question...
You said that i now have to make my own customized RUUs?
What do you mean by that?
If you don't mind, you could send me a pm, I don't want to spam this thread with my stupidity.

Now you can flash ANY rom you want.
ALL cooked ROms - really all - without the chance of bricking = your device is SAFE.
IF you respect this little thing
every RUU Rom Update Utility
contains:
1. Enterbootloader.exe
2. Rapitool.exe
3. RomupgradeUtility.exe (the one you start)
4. RUUGetinfo.exe
5. RUU ressource.dll
6. RUU_signed.nbh (that is the custom system OS - you can put every HERALD .nbh here postet in touchIT3 for example)
7. SPL.nbh ---- !!!!!!!! delete this allways!!!!!!!!! ------ (it is in all official RUU but delete it)
now you can flash with an official update tool all custom roms for you herald.
But don´t use wing roms - the keyboadmapping is different.
There are good herald roms, too.
Good luck
umchriswho said:
So now i won't be able to put in the HTC RUU anymore?
All right, sorry i'm being so stupid, but here's another question...
You said that i now have to make my own customized RUUs?
What do you mean by that?
If you don't mind, you could send me a pm, I don't want to spam this thread with my stupidity.
Click to expand...
Click to collapse

Dear Maestro Help upgrade to WM6
Dear Canonyang,
Have the following
Dopod C800 WM5 5.1.422 (Build 15633.3.2.0)
Can you please help me upgrade to WM 6
Gratefully
neelanjoo
canonyang_China said:
please warn people in your post.
and why don't you use jspl.it's quick and safely.uspl too slow but simply use
Click to expand...
Click to collapse

IPL and SPL that don't match

I started a new thread so that people wouldn't have to read through my trials but long story short I have a G3 wizard and I'm trying to flash it. Followed all of the steps in the guide by vippie. I used the button rom to start with but mine was one of the many that stopped at 98% and gave me error 302 so I ended up using the XDA mini rom as the alternative that was suggested.
Now I've flashed my phone three times with the same rom to try and get the IPL and SPL the same but to no avail. The IPL and SPL are 1.05 and 2.25 respectively. Any help would be greatly appreciated.

hey i flashed my tmobile mda to a chinese rom too and then it changed spl to a diff version than the ipl and then i tried to flashed it with love rom and still it doesnt change the ipl and spl to the same version that i had before, then i removed the battery then my phone does not charge or turn on anymore, i have a g4 by the way, i m not sure if i bricked it or not

joco2560 said:
hey i flashed my tmobile mda to a chinese rom too and then it changed spl to a diff version than the ipl and then i tried to flashed it with love rom and still it doesnt change the ipl and spl to the same version that i had before, then i removed the battery then my phone does not charge or turn on anymore, i have a g4 by the way, i m not sure if i bricked it or not
Click to expand...
Click to collapse
I think you may have been trying to offer your empathy for my particular situation but that's what we in the business call thread jacking. Start your own thread please. Thanks for the comments though.
I was thinking today I may give flashing the button rom another try. Any suggestions people?
And a bump for some professional help and good luck as well.

SharpieMarker said:
I think you may have been trying to offer your empathy for my particular situation but that's what we in the business call thread jacking. Start your own thread please. Thanks for the comments though.
I was thinking today I may give flashing the button rom another try. Any suggestions people?
And a bump for some professional help and good luck as well.
Click to expand...
Click to collapse
wow, basically the same problem just trying to let u no that other ppl r having the same problem and i thought my problem would've helped in some ways...thx for trying to be nice at the end but ur not. sry i forgot to metion that:" hey, SharpieMarker im having the same problem that ur having..."in my previous post

joco2560 said:
wow, basically the same problem just trying to let u no that other ppl r having the same problem and i thought my problem would've helped in some ways...thx for trying to be nice at the end but ur not. sry i forgot to metion that:" hey, SharpieMarker im having the same problem that ur having..."in my previous post
Click to expand...
Click to collapse
Well I apologize if I came of as a douche, I guess I didn't understand what you were saying exactly. I appreciate any support I can get with the issues I'm having so its good to know I'm not the only one. Thanks joco.

SharpieMarker said:
Now I've flashed my phone three times with the same rom to try and get the IPL and SPL the same but to no avail. The IPL and SPL are 1.05 and 2.25 respectively. Any help would be greatly appreciated.
Click to expand...
Click to collapse
Surely you're not serious? oh Jesus, you are.
OK... SPL is separate from IPL, not only is it impossible to get them to be "the same version" it would also achieve nothing to actually do so either... so please, the procedure is very simple, you flash a patched SPL, you flash your crap on. Job Done... I thought there was already a patched SPL for G3... do I need to make one of those as well?!?

Olipro said:
Surely you're not serious? oh Jesus, you are.
OK... SPL is separate from IPL, not only is it impossible to get them to be "the same version" it would also achieve nothing to actually do so either... so please, the procedure is very simple, you flash a patched SPL, you flash your crap on. Job Done... I thought there was already a patched SPL for G3... do I need to make one of those as well?!?
Click to expand...
Click to collapse
Well that seems logical however I was misinformed. SO I've flashed this Xda_mini rom, then what is the cause of the issues I was having getting a connection error when trying to CID unlock? Wizards have to be CID unlocked before flashing 2.X roms right?

What started as a simple, objective thread, has become quite confusing in a matter of a few posts.
joco2560 said:
wow, basically the same problem just trying to let u no that other ppl r having the same problem and i thought my problem would've helped in some ways...thx for trying to be nice at the end but ur not. sry i forgot to metion that:" hey, SharpieMarker im having the same problem that ur having..."in my previous post
Click to expand...
Click to collapse
Well, in fact your problem ISN'T the same as SharpieMarker's because his phone is still alive...
I believe you tried to downgrade a G4 to 1.xx bootloader which only exist for G3. Once the battery came out your phone could never boot again. Say bye bye to it...
SharpieMarker said:
Well that seems logical however I was misinformed. SO I've flashed this Xda_mini rom, then what is the cause of the issues I was having getting a connection error when trying to CID unlock? Wizards have to be CID unlocked before flashing 2.X roms right?
Click to expand...
Click to collapse
A LOT of people are reporting failed downgrades which 'block' the SPL at 2.xx. Once there even after 30 flashes the SPL never lowers to 1.xx to allow CID unlocking.
No solution is known until now...
Olipro said:
Surely you're not serious? oh Jesus, you are.
OK... SPL is separate from IPL, not only is it impossible to get them to be "the same version" it would also achieve nothing to actually do so either... so please, the procedure is very simple, you flash a patched SPL, you flash your crap on. Job Done... I thought there was already a patched SPL for G3... do I need to make one of those as well?!?
Click to expand...
Click to collapse
There isn't and i believe you should patch one...
cheers

mestrini said:
A LOT of people are reporting failed downgrades which 'block' the SPL at 2.xx. Once there even after 30 flashes the SPL never lowers to 1.xx to allow CID unlocking.
No solution is known until now...
Click to expand...
Click to collapse
So what is the solution or is it the patched SPL that Olipro is referring to?

The HardSPL (Olipro) is ONLY for use with G4. The flash program should keep you from flashing it to a G3 Wizard because their SPL code are not compatible.
SoftSPL also doesn't work for G3 wizard.
joco2560 should be produced a brick because as I know, no unofficial Chinese ROMs are equipped with G4 IPL and SPL.

Man if only these guys would have read the WIKI... There is a link in my signature to an outstanding tutorial for newbies. Just read it and you will feel enlightened. Everything will seem so simple and life's purpose will become evident... Just Kidding but seriously guys... Read the damn WIKI... I'm tired of reading about bricks.
NOTE:: THIS ENTIRE POST IS ONE GIANT LINK TO THE WIKI I'M TALKING ABOUT!!!
READ IT!!!

starkwong said:
The HardSPL (Olipro) is ONLY for use with G4. The flash program should keep you from flashing it to a G3 Wizard because their SPL code are not compatible.
SoftSPL also doesn't work for G3 wizard.
joco2560 should be produced a brick because as I know, no unofficial Chinese ROMs are equipped with G4 IPL and SPL.
Click to expand...
Click to collapse
Alright, this is helpful and I was hoping there might be a few suggestions as to what to do at this point. Thanks guys for the comments.

dharvey4651 said:
Man if only these guys would have read the WIKI... There is a link in my signature to an outstanding tutorial for newbies. Just read it and you will feel enlightened. Everything will seem so simple and life's purpose will become evident... Just Kidding but seriously guys... Read the damn WIKI... I'm tired of reading about bricks.
NOTE:: THIS ENTIRE POST IS ONE GIANT LINK TO THE WIKI I'M TALKING ABOUT!!!
READ IT!!!
Click to expand...
Click to collapse
Okay, firstly I have not bricked my device. I have read all of the guides and walkthroughs before attempting anything on my wizard. Unfortunately your guide that you have written, just like the other ones, has not answered my question or told me what I should do (unless I have missed it somewhere which is possible).

Okay, after some finagling with the lokiwiz application I managed to unlock and then cid unlock my phone however the IPL is still 1.05 and the SPL is 2.25. Is that accurate or should the SPL be lower now? Do I need to reflash?
Alright, after re-re-re-re-re-reading the instructions I think I understand the bit about IPL and SPL. I think. Feel free to clarify though.

If lokiwiz does not show any errors during unlocking (NOTE That lokiwiz always shows successful regardless it is actually unlocked or not, so the error message is the most important), then either try to flash Button's ROM again and you will get 1.05 IPL and SPL (That's my way), and others suggests to upgrade IPL and SPL directly to 3.08.

starkwong said:
If lokiwiz does not show any errors during unlocking (NOTE That lokiwiz always shows successful regardless it is actually unlocked or not, so the error message is the most important), then either try to flash Button's ROM again and you will get 1.05 IPL and SPL (That's my way), and others suggests to upgrade IPL and SPL directly to 3.08.
Click to expand...
Click to collapse
There was no error message when I CID unlocked. It successfully unlocked both times (the first using the U command and after a restart using the C command). My phone restarted twice during the unlocking so I think it went just fine. So should I proceed with the flashing of the tmobile rom? After the unlocking I have an IPL of 1.05 and an SPL of 2.25.

You can always go back to Button's ROM, so it's OK to flash T-Mobile ROM.
However I still recommend to flash Button's ROM once more first.

starkwong said:
You can always go back to Button's ROM, so it's OK to flash T-Mobile ROM.
However I still recommend to flash Button's ROM once more first.
Click to expand...
Click to collapse
Well I decided to flash the t-mobile rom and it went smooth. Everything works fine. So now I have an IPL and SPL of 2.26 so I can flash some of the more interesting roms right? Thanks for all the help and advice guys. Much appreciated.

SharpieMarker said:
Well I decided to flash the t-mobile rom and it went smooth. Everything works fine. So now I have an IPL and SPL of 2.26 so I can flash some of the more interesting roms right? Thanks for all the help and advice guys. Much appreciated.
Click to expand...
Click to collapse
Yes you should now be CID unlocked and can flash any Rom you want as long as it does not contain an IPL/SPL.
And by the way, It does tell you in that WIKI exactly what you need to do to CID unlock your device. (The SPL will not downgrade to 1.05 unless you flash the button Rom again AFTER completing The Unlocking Process through lokiwiz. I wouldn't even reccomend flashing the button Rom again. It's pointless because Flashing the T-Mobile Rom is going to upgrade you IPL/SPL to a higher, matching pair and is going to give you a very strong, stable base rom to flash to a custom Rom From.

SharpieMarker said:
Well I decided to flash the t-mobile rom and it went smooth. Everything works fine. So now I have an IPL and SPL of 2.26 so I can flash some of the more interesting roms right? Thanks for all the help and advice guys. Much appreciated.
Click to expand...
Click to collapse
I think you should check your CID status with WST before trying to flash a custom ROM. Lokiwiz doesn't check for errors and proceeds as if everything went ok even if it didn't.
For all we know your phone might be originally from T-Mobile and even CID locked would always accept an official ROM.