Related
I guess some of you may interested to mod your kaiser screen to tilt almost 90 degree, then you can use it on your car without any holder.
Here's a guidance document i pull together.
Remember, do it only on your own risk.
Enjoy!
Too scary for my taste.
Thanks! That's looks a little intimidating.
So basically is the only reason it tilts more is because the two plastic pieces are cut? What would happen if those two pieces were cut totally?
Thanks again.
A prediction...
Very cool mod, but I predict a large number of bricks on this one...
As a hardware design engineer professionally, I would have to recommend against this mod unless you are a technician and have access to the facilities.
If you are dead set on doing this mod, please take the time to prepare your environment - at the minimum, get an ESD strap and make sure you're properly grounded. Ideally, a strap and a mat are called for.
This is an ESD nightmare waiting to happen. Doing this on your kitchen table or coffee table - especially at this time of year, is literally Russian Roulette as to whether you will discharge 30K volts or so into the PCB and totally brick the device.
As a rule of thumb, if you don't know what ESD is, you probably shouldn't even consider this mod, or any other that involves opening up the device and exposing the PCB.
Just my 2 cents. Caveat Emptor, etc. etc.
Regards,
Jeff
nice..
i was thinking of something along the same thoughts, as it tilts, why have a holder!! just drive safe (as always)
exept, im still waiting for mine..
Wow! Nice Hardware mod tonychen! Just posting to register my shock and awe! Great writeup too!
@trick420: As can be seen, like Hermes, most sensitive electronics components are in a metal Faraday cage so this isn't as dangerous as it looks from an electronic standpoint. It's always a good idea to use a grounding strap however.
All those plastic tabs are gonna be a real bear to work with though. The TyTN only had a few but the Kaiser appears to be riddled with them.
trick420 said:
Very cool mod, but I predict a large number of bricks on this one...
As a hardware design engineer professionally, I would have to recommend against this mod unless you are a technician and have access to the facilities.
If you are dead set on doing this mod, please take the time to prepare your environment - at the minimum, get an ESD strap and make sure you're properly grounded. Ideally, a strap and a mat are called for.
This is an ESD nightmare waiting to happen. Doing this on your kitchen table or coffee table - especially at this time of year, is literally Russian Roulette as to whether you will discharge 30K volts or so into the PCB and totally brick the device.
As a rule of thumb, if you don't know what ESD is, you probably shouldn't even consider this mod, or any other that involves opening up the device and exposing the PCB.
Just my 2 cents. Caveat Emptor, etc. etc.
Regards,
Jeff
Click to expand...
Click to collapse
I'm pretty sure everyone knows what electro-static discharge is.
so there are two bits of plastic going around the hinges that are stopping the display from tilting fully? like a tendon or do these bits of plastic go up against something to stop motion?
Yes you are right!
The ESD strap i guess is not available to most people except hardware engineers. The simplest way to discharge the static electricity is to wet your hands with a wet towel.
trick420 said:
Very cool mod, but I predict a large number of bricks on this one...
As a hardware design engineer professionally, I would have to recommend against this mod unless you are a technician and have access to the facilities.
If you are dead set on doing this mod, please take the time to prepare your environment - at the minimum, get an ESD strap and make sure you're properly grounded. Ideally, a strap and a mat are called for.
This is an ESD nightmare waiting to happen. Doing this on your kitchen table or coffee table - especially at this time of year, is literally Russian Roulette as to whether you will discharge 30K volts or so into the PCB and totally brick the device.
As a rule of thumb, if you don't know what ESD is, you probably shouldn't even consider this mod, or any other that involves opening up the device and exposing the PCB.
Just my 2 cents. Caveat Emptor, etc. etc.
Regards,
Jeff
Click to expand...
Click to collapse
The plastic needs to be cut as it stop the two metal blocks to tilt up more. If you cut it totally, you still get the same result, so i don't see to much reason for doing that.
juiceppc said:
Thanks! That's looks a little intimidating.
So basically is the only reason it tilts more is because the two plastic pieces are cut? What would happen if those two pieces were cut totally?
Thanks again.
Click to expand...
Click to collapse
Uploaded the guide to a mirror:
http://rapidshare.com/files/73519908/Kaiser_Screen_Mod.pdf
This is a great GUIDE!!!!
Thanks Tonychen.
Nadavi.
Not to be a killjoy but people should be aware that the plastic strips are there to prevent over extension of the thin ribbon cables connecting the display to the body.
You may not actually part these immediately but constant over extension will cause them to fail early.
Learnt my lesson years ago on a Nokia 9210i (stop that cursing there will you!!! someone had to buy them!) Smiles.
very intimidating but too scary for me. i would rather not break my $500 dollar phones just so i can see the screen go a couple more degrees more
just done it and its ace
slight idea change tho because its next to no use haveing it at 90 degree angle unless in car, not cutting away plastic compleatly makes it a little stiffer and will only be able to make the screen angle to 90 by choice so you shudnt break anything as you wont do it all the time. just a thought.
very nice mod.
this is going to be off topic though. " is there anyway we could tighten the hinge? mine is getting loose already.
Just a thought but isnt it alot easier to rest the back underside of the phone on a small object. this will tilt it forward and make the screen visible in the same way... You could use a small velcro patch to secure it to the said object which in turn could secure to the dashboard etc in the same manner. Alot less scary to do and you wont run the risk of damaging your phone.....
Pretty cool, but idk about messing w/ the structural integrity.
I always thought ESD was a myth. I've been working on computing hardware for almost a decade, and I do take the necessary precautions when working on new/mission critical equipment. But 90% of the time I am working on refitting relatively old workstations/servers where my boss has basically told me he doesn't really care if these items make it back into active service or not, so stuff like that I always go commando on, and I've never had a single piece of equipemnt go spontaniously DOA on me while handling it. (i.e. every single item of equipment I've retired due to DOA was reported as DOA before I touched it...)
Oh, and I have a mini tesla coil in my cube... j/k
Here is my tesla, got bored a couple weeks ago and made one, its like my fifth one.
tonychen said:
I guess some of you may interested to mod your kaiser screen to tilt almost 90 degree, then you can use it on your car without any holder.
Here's a guidance document i pull together.
Remember, do it only on your own risk.
Enjoy!
Click to expand...
Click to collapse
Who's daring enough to try this on the new Touch Pro 2?
Yes, I already broke my phone. Go ahead, grin and chuckle..now that you've gotten it out of your system, anyone want to offer a little guidance? Never disassembled a newer cellphone before. New glass is ordered and has been shipped, just waiting for it to arrive. I'm hoping the process is fairly simple. I do have a specialized set of screwdrivers with all the hard-to-find bits, so that's not a problem ..it even has the tiny blackberry bit.. but from what I can see HTC uses standard micro Philips screws. Yay for standard formats!
Sent from my HTC PH39100 using xda premium
If this phone is anything like hd2 you're gunna want the flat pry tools they sell (search hd2 screen replacement tools). Their not needed but a nice handy thingy to have, other wise you might crack your LCD from flexing it too much.
Sent from my HTC PH39100 using XDA App
I wont grin and chuckle too much, I broke my Atrix after 4 days.
The Vivid screen seems very fragile. 2 of my coworkers have broken theirs within a few weeks of having them. Small drops from waist distance. Its too bad because I have seen the current Samsung models dropped from 6 feet face first and survive
Sent from my HTC PH39100 using xda premium
Yeah, I've cracked mine as well. If you google HTC raider teardown on YouTube.. There's a vid.... Butttt, it's not in English and it's a teardown not a screen replacement tutorial.
It seems as thought HTC has been using reeeeally thin glass in their devices.
Whered you get the glass? It'd be very thoughtful of you to do a tutorial as you do it. I really want to replacement mine but if you remove one on the screws by the battery it voids your warranty
Send it to HTC then? You get a 1 year warranty when you buy the phone.
Honestly, I think Corning had another incident of releasing faulty glass. I've dropped mine numerous times, from pretty high up and I don't have a single scratch on my phone.
travisxcore said:
Send it to HTC then? You get a 1 year warranty when you buy the phone.
Honestly, I think Corning had another incident of releasing faulty glass. I've dropped mine numerous times, from pretty high up and I don't have a single scratch on my phone.
Click to expand...
Click to collapse
How much is it for them to fix it?
I have no idea. Shoot them an email (not Support Inquiry, youre gonna wanna send it to Repair Inquiry) and they should be able to tell you. Make sure you fill out the S/N box out now, or their just gonna send you an email back asking for it.
travisxcore said:
I have no idea. Shoot them an email (not Support Inquiry, youre gonna wanna send it to Repair Inquiry) and they should be able to tell you. Make sure you fill out the S/N box out now, or their just gonna send you an email back asking for it.
Click to expand...
Click to collapse
I'll do that right now. Thanks alot
(sorry to hijack the thread lol)
They use a double sided tape that hopefully comes with your replacement screen , I tried to replace a water damaged screen and it really wasn't a fun process
Sent from my HTC PH39100 using xda premium
It didn't fall very far..
Yeah when mine fell I had it in a shirt pocket, bent over to pick something up and it slid out, fell about a foot and a half..directly onto the search button corner on ceramic tile. Crunch. I ordered a new panel from tmart.com .. I got a confirmation email back on the 4th saying its been shipped via usps.. should be here soon. I hope it comes with everything I need - cost me about $50.00 with the shipping and everything. I paid the extra 3 bucks for insurance lol..
bproulx said:
Yeah when mine fell I had it in a shirt pocket, bent over to pick something up and it slid out, fell about a foot and a half..directly onto the search button corner on ceramic tile. Crunch. I ordered a new panel from tmart.com .. I got a confirmation email back on the 4th saying its been shipped via usps.. should be here soon. I hope it comes with everything I need - cost me about $50.00 with the shipping and everything. I paid the extra 3 bucks for insurance lol..
Click to expand...
Click to collapse
So, how was the installation process? And did it come with the adhesive? I'm going to buy it from that site as well
And then it was fixed..! FTW!
Ok sorry for the delay getting back to you guys.. been frantically waiting for the screen to clear US customs (ugh) and arrive, which it finally did today. I was able to get my hands on it at about 3 this afternoon, but I wasn't able to actually look at it until about an hour ago..
So.. I open the package, big grin on my face..and the first thing I notice is that the glass is AT&T branded. Funny, considering I'm in Canada and using Rogers..but hey a digitizer by any other name...and all that. So! I open the bag that my "tools" came in.. There are 2 blue plastic tools, one a prying tool and one looked a lot like a guitar pick. Cool. There are also 2 screwdrivers included, and I'm momentarily excited, until I realize they're just tiny torqx bits. The Raider uses TINY philips head screws, so those were useless. I put them into my tiny tool set..for later consideration.
Back to the screen. Looks like it the real deal, so I watch half of the teardown vid on youtube.. As mentioned in an earlier post it isn't an english-language vid so aside from seeing the locations of the screws and the methods of levering off the internal components, there's no exchange of information going on. I would like to mention however that the video kind of glazes over the locations and removal processes for some sensitive connections, so having only experienced laptop repairs personally.. I was in fairly uncomfortable and unfamiliar territory - but I was determined.
I tried several ways at getting the phone down to its base components, and finally succeeded in locating the panel's ribbon connector interface on one of the phone's circuit boards. I had to remove the back of the phone, pull the batt, sim and sd, and pull the 4 main screws that lock the housing down onto the phone.. From there its a matter of levering off the black plastic shell and whats underneath is a whole lot of tech in a very tight space. There were 3 or 4 wires I had to disconnect, about 15 tiny screws in 3 different lengths, and then when all was said and done I had to pry the busted panel off using the supplied blue lever tool (pretty handy, actually.) and then lift the lcd away from the metal housing enough to slide the old connector out and the new one through.. This was a very tricky process - I drink way too much coffee to hold completely steady for long..lol.. Finally got it all through, but by this time I had smudged the inside of both glass surfaces pretty badly and it took some serious mechanical dexterity to hold the surfaces and wipe them down without wrecking any of the flapping, loose circuit boards, screens, etc.. it was a frightening experience.. I won't lie.. I definitely feared the worst possible outcome given my limited experience.
So.. the panel's ribbon cable is inserted, the white clip back down securing it.. I manage after several attempts to remember how to put the puzzle all back together, and after about 45 minutes of messing with it I had a visually complete phone again. I hit power, and miracle of miracles the HTC logo flashes on the screen.. I'm hopeful..
The phone boots up, looks great (aside from a few smudges I missed on the inside..grr) so I start touching the screen and here's where we have the first problem..lol.. its recognizing that I'm touching the screen..but not really accurately.. it seems to be that there are dead areas.. So now I'm thinking I broke something..lol..
Smoke break.
Took it all apart again, forgot to clean the smudges, removed and re-seated all the connections, and about 15 minutes later I had it back together again. I booted it up and waited.
Success!! It sees where I'm touching accurately now - I think the ribbon must have moved while I was putting it back together, I was shifting things a lot as I was trying to figure it all out, so I must have stressed the cable enough to move it slightly in the slot.. that, or I didn't have it all the way in / straight the first time I did it. Either way, it works fine now. I was successful on the 2nd attempt, and now the only difference is that this glass feels..rougher? less smooth? not sure how to describe it.. it feels different, anyway.. and the at&t logo of course. Aside from that, you'd never know it was in pieces an hour ago..lol.
Would I do this again? ..I hope I don't have to. Its not impossible, but man, if you're going to try this BE SUPER CAREFUL!! lol..
edit: and no - it didn't come with the double sided tape, but it seems to be staying without having to replace it.. it wasn't too hard to remove it from the panel, but getting it back on straight took some finesse.. lol.. it comes apart easier now when you're tryingn to disassemble it..but seems to be holding together fine on its own.
travisxcore said:
Send it to HTC then? You get a 1 year warranty when you buy the phone.
Honestly, I think Corning had another incident of releasing faulty glass. I've dropped mine numerous times, from pretty high up and I don't have a single scratch on my phone.
Click to expand...
Click to collapse
Corning makes the glass on the Raider/Vivid?
I would suspect it to be more sturdy if its corning, my SGS has been without a screen protector and still does not have any scratches. Yes i know SGS is Gorilla Glass and this is not but i would think it would be stronger.
@ bproulx
You should take it apart again and make a tutorial . I hope i never have to go though what you did. Knock on wood.
lol..might take it apart again..
So..I have smudges on the inside of the glass. Stupid sweaty fingers. Now I'm tempted to pull it apart again ..but not far enough to make a tutorial lol.. besides.. I'm glad I didn't have a camera on me - you guys woulda had a good laugh at me breaking into a sweat trying to pry loose the glass panel the first time..lol. I know it was already broken but (a) I was trying not to cut myself on it and (b) I was also trying not to break the lcd underneath. Which I believe also has smudges on it. Oi.. I guess I'll have to get in there and clean it. Probably not tonight tho. I'm just glad the thing still works - I was scared I was going to bust something. There are a LOT of little things in there. For the record the CPU looks neat. Its smaller than a sim card, a little bigger than a micro sd. Pretty impressive.
bproulx said:
So..I have smudges on the inside of the glass. Stupid sweaty fingers. Now I'm tempted to pull it apart again ..but not far enough to make a tutorial lol.. besides.. I'm glad I didn't have a camera on me - you guys woulda had a good laugh at me breaking into a sweat trying to pry loose the glass panel the first time..lol. I know it was already broken but (a) I was trying not to cut myself on it and (b) I was also trying not to break the lcd underneath. Which I believe also has smudges on it. Oi.. I guess I'll have to get in there and clean it. Probably not tonight tho. I'm just glad the thing still works - I was scared I was going to bust something. There are a LOT of little things in there. For the record the CPU looks neat. Its smaller than a sim card, a little bigger than a micro sd. Pretty impressive.
Click to expand...
Click to collapse
I've taken apart laptops (MacBooks at all) and successfully reassembled them so I think I'm up to the job. I'm reaaaally thankful that it says AT&T at the top and not HTC like the pic shows (since I'm on att).. Another question though, did you successfully get the "void" plastic piece back over the screw? Because, I want to keep this phone as "under warranty" as possible
Getting better at taking it apart..lol..
Chism87 said:
I've taken apart laptops (MacBooks at all) and successfully reassembled them so I think I'm up to the job. I'm reaaaally thankful that it says AT&T at the top and not HTC like the pic shows (since I'm on att).. Another question though, did you successfully get the "void" plastic piece back over the screw? Because, I want to keep this phone as "under warranty" as possible
Click to expand...
Click to collapse
No, the little void sticker on mine was less like a sticker and more like... glue, with paint on it.. lol.. it just flaked apart when I tried to lift it.. but I wasn't concerned with preserving it. Maybe if u use an x-acto or something like that you can lift it intact..? Let me know how you do.
I started getting some random touch input glitches yesterday, and today they got worse.. then my son spilled hot coffee on me and I dropped my phone on the carpet where it of course popped apart..lol..and then when I booted it back up I had some *major* touch glitches.. it was seeing input higher up than the actual contact point, and just acting real buggy..the phone was lagging.. so I took it apart again, completely.. took my sweet time reassembling it this time - I even got out the micro-fibre cloth and cleaned all the glass, and voila.. this time - its like new. I can already tell its put together right this time, which tells me something wasn't quite right before - I'm guessing I didn't get the ribbon cable seated properly before.. there are a lot of tiny, offset contacts on the end of that little cable. Anyway, I guess the moral of the story is screw warranties, and the more times you disassemble your phone the better you get at it.. lol.. it wasn't anywhere near as intimidating this time around. Felt kinda easy, actually. I think I just psyched myself into thinking it would be hard to do the first time around.
I do miss my original glass tho.. I'm thinking about contacting HTC and ordering an oem panel lol.. this one feels.. grippy. The HTC one felt smooth as silk.. I dunno this one kinda feels more like window glass. Meh.. better than a broken ghetto phone. At least now I can whip it out in public without hanging my head in shame and peeking around to see who's looking at my ugly screen. I never even tried HTC directly..I just googled the part and went with the one with good reviews..
OMFG...FML..
Sooo.. I got angry at my Raider today.. started doing the weird touch input glitches again after a battery pull, got frustrated and slammed my phone down on the table in anger...and.... smash. Brand new panel is now ten times as shattered as the old one was. AND...now the phone won't even light up. AND..it looks like I may have cracked the actual LCD this time.. just a small crack at the very bottom - wouldn't even be visible with the shell on the phone.. but.. I'm not very optimistic. I get absolutely nothing on my screen when I boot the phone, all I get is one haptic "bump" and thats it. Nada.
Sooo... looks like I need a new phone. Again.
Lame.
There goes $600.00
....sigh.
Anyone wanna donate an old android device to a guy who's now really really sad and has no phone? LOL.. why did I give away my legend????
Not giving up my phone!! LOL!
Ok so I decided to try my luck at replacing the LCD as well as the busted digitizer that I just re-broke..lol.. back to tmart, and ordered both. I really wish I could have found the whole assembly pre-built, but the only company I found selling both as a single unit had a minimum order of 5 pcs. Out of my price range for repairs, although with my track record maybe it wouldn't have been a bad idea? lol.. anyway, I just bought both parts from tmart and am still waiting for one of them to show up. The good news is I was able to replace the LCD already. It really is just held in there with tape. Like.. there's nothing really holding it all together..you'd think with all those screws and tabs they could have come up with a better way?? Ah well. I have a display again, but until I can get the digitizer and install it I'm without input.. so I can just watch the phone boot and then sit on my lock screen. Or boot into recovery mode and use the vol and power buttons to mess about.. But why..lol. I'll just wait.
I'm just happy that nothing else seems to be affected. I had my alarm going off still with no screen, so that tipped me off that everything else should still be ok. I won't know for 100% certain til I complete the repair, but it looks promising. I picked up a used HTC Magic (ugh) from kijiji for $80 and it came with 3 batteries, 3 chargers, 3 usb cables, 3 leather cases, and a bunch of other crap in threes. Just so I'm not completely without a phone in the meantime. Overall not bad for $80 but man is this phone slow. I installed a custom rom **THANKS XDA!!** on it and it improved the performance and look of the OS a little, but it lags a lot even overclocked when just typing a text.. I can't wait to get my phone back!!
Aside from the screens, this phone is pretty tough. I slammed that sucker down pretty hard that day.. Cmon HTC - why didn't you give us gorilla glass on a $600 LTE phone!?!?!?!? I wish I could find an aftermarket panel that was made from gorilla glass. That would totally rock!
Yeah, i really wish they would've put gorilla glass on it. I used to have the atrix and ive dropped it on tile floor at least 3 times... Nothing. Keys in the same pocket as phone.. No scratches at all.
I didn't want to try my luck, so I just got a replacement vivid
hi folks. i managed to replace my galaxy note front glass with a new one i got from ebay for 19$ and i want to make a step by step guide on how it can be done.
i did it using common tools and a s load of pacience and attention.
the tools i used are: heat gun with hi and low settings, exacto knife set,small phillips and flat screwdrivers, goo gone, and optional a screen protector.
first take the phone apart as it's describet in countless of threads and youtube videos. you should end up with the screen assembly shown in the first picture.
now we have to separate the glassscreen from the frame it sits on. for this we fire up the heat gun.
a few words about using the heat gun.
-my gun had 2 settings: low and high. during all this process i used it on low.
-don't put the gun directly and/or close to the thinn plastic wires that hold the two connectors.
- dont hold the gun in the same place more than 3 seconds, instead swipe the gun around the spot and the screen like u would do with a paint brush when painting.
- dont hold the gun too close, that is closer than 3 inch
-concentrate on the spot u working at but try to heat up the whole screen assembly, as it has to give away from all the points kind of at the same time, and not just the point u working at.
- dont overheat the screen as this will damage the amoled. thats how i got the two yellow spots on my screen. first one by accident and second one intentionaly to see if indeed the overheating is what caused it.
A very good rule for this is dont heat the phone more than you can bear to touch it cause afterall you have to hold the phone while working on it...
the way i did it is :
-i heated up the whole screen assembly, back and front, for a minute or two
- than i started to stick the tip of the exacto knife between the glass and the metal edge that sorrounds it. i started from the upper right corner, the side where the front camera is. see photo 2.
the goal is to unstick the glass from the frame. in photo 3 the frame and the screen is shown without the upper glass. this photo was taken after i finished everything, thats why the screen can be seen inside the frame. but i posted it to show the black sticky tape that its used to hold the glass to the frame. i think is the same kind of sticky tape thats used in all the touchphones including iphone to hold the front glass to the rest of the phone. in photo 4 i unsticked some of the tape to show it better. this tape is the main thing that holds the the glass to the frame. the other thing that hold the screen to the frame is some sticky glue on the back of the screen. but this is much softer and thiner glue. this is the reason why i say to heat up the whole screen assemby including the backside, to make it easyer to unstuck the glass and scren thats glued to it.
- once you get a bit of a foothold in the upper corner between and the glassand the frame you continue the folowing procedure again and again until the glass and screen detaches from the frame:
-every 2 minutes or so , when i feel the asemby cooled down, i'd heat up the whole assembly for 5 seconds or so, than concentrate on the spot i worked on for another 5 seconds, than move/push the exacto knife a bit. dont force it. after a while youl get a feel of it. if the exacto knife happend to be out, i would heat up the blade after heating up everything else, and than put the blade in.
prevent the freed parts from sticking back to the frame by using the rest of the exacto knife blades as shims.
once it detaches it should look like photo 5- the glass glued to the screen.
- now we have to detach or unglue the glass from the screen.
procedure is the same: start somewhere, heat, put knife in, etc... i used a second knife as shim folowing the first knife, and after avery couple moves i would get the knife out and wipe off the epoxy glue. heat the blade and put it back in.
when finished you should have something like photo 6 and 7: free screen covered in glue epoxy residue.
- now we have to get rid of the glue residue. i took the bulk of it usinga flat exacto knife blades like the one in photo 8 and 10. just warm the place a bit with the air gun and scrape it off with the blade. to clean what was left i used a bit of goo gone on a pice of cloth or napkin photo 9.
cleaned screen can be seen in photo 11 - sadly out of focus.
if u are like me and r impatient to test the screen you can just connect with just the side connector like in photo 12 and 13. the upper connector is for the s pen digitizer. side connector is for the screen and touch digitizer.
now all that's left is to put the phone back together except leave the new glass for last.
-first thing is to put the screen(without the glass) back on the frame. try to center it just right, so that ther's a little bit of space between the sides of the screen and the frame.
at this point all that will hold the screen to the frameis the thin layer of glue on the back of the screen. after centering and lowering the screen in the frame procede to put the phone back together folowing in reverse order the same steps used to disasambe it. when finished you should end up with the whole functioning phone except the front glass -as seen in photo 14.
now you can chose to trim and put a screen protector on the scree so as to fill the empty space between the screen and the glass - the space where the glue was, or you can just leave it empty. you can put a screen protector anytime after by removing the glass. which should be much easier to remove now that its held in place only by the blach sticky tape on the edges. just use some suction cap to remove it, starting at an age, and remove it like fliping a page. see photo 16. i used the note for 2 weeks without the screen protector in the empty space and it worked without a problem onlt thing was that when i pushed hard the glass would touch the screen and leave a bit of dirt in that place. thats why i decided to put the screen protector to fill the void. in photo 15 i raised the screen protector to make it visible in the photo.
if you are like me and worry that somehow the glass might fall off the phone you can always get a hard plastic case for the phone, like the one in the pics. it's made of 2 parts. one goes on the back one on the front and they snap togeter around the phone. this will hold the glass in place no matter what while it will also protect the phone.the case is in photos 17 and 18. i got this one of ebay for 8$ and free shipping.
the last thing to be done is:
for some reaseon the touch screen became much more sensitive after removing the glue so you need to lover the touch sensitivity. for this get the touchscreentune app from the market. it works with galaxy note and galaxy s2. put the sensitivity from the recomended 25 to 50.
the best thing about this procedure is that i dont have to worry about the f ing glass anymore. if it brakes again i'l just order another one and in under 2 minutes i can replace it. all i have to do is get the phone case off, put a suction cap on , , remove the old glass , and put the new glass. that's it.
because it takes 4 to 8 hours i would recommend the process to be done in 3-4 sessions as people would get tired after 2 hours of work and tend to lose focus, attention, patience and start to push to get it faster done, and that's when bad stuff happens like yellow spot burn on the screen or small scratches. another thing about scratches, even if u manage to scrach the screen dont worry to much as the scratches are almost invisible when the screen turns on. youl see what i mean ....
i do have one question: WHY DID SAMSUNG DECIDE TO GLUE THE SCREEN TO THE GLASS INSTEAD OF HAVING THEM SEPARATE LIKE ALL THE OTHER TOUCHPHONES?
I do the same for Galaxy S. I removed broken pieces of glass from device using guitar pick and carefully glued a new glass on each side. 9$ (free delivery) on ebay.
blank for future use
blank for future use
anonymous572 said:
I do the same for Galaxy S. I removed broken pieces of glass from device using guitar pick and carefully glued a new glass on each side. 9$ (free delivery) on ebay.
Click to expand...
Click to collapse
what kind of glue did you use? where did u get the glue from? how did u do it?
i didnt glue the glass back to the screen. i just put the glass on the frame. to fill the void where the glue was i trimed a regular screen protector and put it inbetween the glass and the screen. but it works same without it.
Very interesting, I didn't think it was possible because the glass is glued to the SAMOLED panel. I'm very glad that I am wrong.
As much as I hate to think about it, a guide like that would probably come in handy for many of us at some point.
*knocks on wood*
pboesboes said:
Very interesting, I didn't think it was possible because the glass is glued to the SAMOLED panel. I'm very glad that I am wrong.
As much as I hate to think about it, a guide like that would probably come in handy for many of us at some point.
*knocks on wood*
Click to expand...
Click to collapse
Nothing is impossible with the right tool and know-how . The glue could probably be uncured with a heat gun, just like ipad. The challenge is not damage the panel and make sure it is dust free after put back the replacement.
It is said impossible because of the difficulty involved. If you can't manage to install a screen protector with perfect alignment and zero dust spike, this task is not for you.
@drevilatwork Thank you for writing this step by step guide!
I dropped my phone last night and it landed face down, cracking the glass.
I'm so upset, but I don't think I have the skills or the tools to do this job myself. I am relieved to learn that the glass can be replaced, but do you know whether the Samsung agents are likely to be able to do this?
they probably wont do it. but you can try showing this thread to some technician or phone repair shop and they might do it for you. they also might charge you a lot to the point where it might be more convenient to just buy a new 260$ screen.
looks scary dude
all im going to say is good luck separating the 2 screens without breaking the lcd or scratching the crap out of it ... this is a 90% epic fail method but thumbs up to the few that may succeed or dont mind their screen looking like its been belt sanded...
Its worth a try, since screen replacement costs 230 euros.
kawgirlval69 said:
all im going to say is good luck separating the 2 screens without breaking the lcd or scratching the crap out of it ... this is a 90% epic fail method but thumbs up to the few that may succeed or dont mind their screen looking like its been belt sanded...
Click to expand...
Click to collapse
actually .. the funny thing is that even if u manage to screch the screen and / or leave dirt behind it doesn't show while the phone is on. it might show when is off but not when is on. i was suprised about that too. and secondly, having to do it again knowing what i know now i would do it without leaving a mark. and in the end is certenly worth a shot before ordering the 260$ screen assembly. the special thing that it requires is pacience and attention.
Why different prices for all the same lenses in this shop ?
drevilatwork said:
actually .. the funny thing is that even if u manage to screch the screen and / or leave dirt behind it doesn't show while the phone is on. it might show when is off but not when is on. i was suprised about that too. and secondly, having to do it again knowing what i know now i would do it without leaving a mark. and in the end is certenly worth a shot before ordering the 260$ screen assembly. the special thing that it requires is pacience and attention.
Click to expand...
Click to collapse
as i said good luck with it and hope you make some money doing it..... ive successfully done the same thing myself but other than it will never look good like a factory screen (not even close), the amount of time it takes to make it look anywhere near acceptable (not like a 10 dollar repair) is big and that makes the repair not really worthwhile doing it for anyone but yourself and even then who spends 700-800 dollars on something and does a repair that makes it look cheap... then theres the whole ordeal of the membrane youre taking the adhesive off of along with the HUGE chance of damaging it.. it is placed with precision and adhered for a reason along with being dust and scratch free... this is a repair that just wont last because things will start functioning improperly for multiple reasons...
im not knocking you or anyone who tries this..im just trying to emphasize the dangers, downfalls and the probability of it being a legit solid repair. also the resale value when the next greatest thing comes along... just beware....
Hmmmm
Well chaps I hate to disagree here, but after speaking to the technical bods at Samsung it appears that the OLED is NOT glued to the glass, but the glass is laminated and bonded in, much like a car windscreen. My screen got broken the other day and I have read the 2 posts on XDA regarding this. Now if you go and have a look at the pics of the other post
http://forum.xda-developers.com/showthread.php?t=1487716
you can clearly see the OLED, although broken, seperated from the glass with no sign of any glue. The reason it broke is that upon heating the glass you will melt the glue, which will then stick to the edges of the OLED and if you pry it at the wrong place/time/too hard/whatever you will break the OLED as it is glued to the bezel itself. So when my glass arrives I am going to attempt to remove the glass using fishing line and pulling it between the glass and the bezel and OLED to release it, the same way as I used to remove car windscreens, and post the results here. I have also been told that the reason for the sticky "epoxy" mess that you encountered in this postis from melting the plastic on the back of the glass (which is the lamination!) by using too much heat.....I mean come on, a heat gun is a bit excessive!! Prying the screen out a bit at a time might work, but will surely end in tears, where as cutting the cold adhesive with a fine nylon cable, which wont scratch the OLED, might just work. I'll keep you posted on my results.
Just throwing an idea out there: maybe the adhesive would be easier to defeat when it's really cold, rather than really hot. I know a lot of adhesives become quite brittle when you put them in the freezer, superglue and epoxy for example. And the electronics/plastics of the display could be relatively fine with the low temps.
pboesboes said:
Just throwing an idea out there: maybe the adhesive would be easier to defeat when it's really cold, rather than really hot. I know a lot of adhesives become quite brittle when you put them in the freezer, superglue and epoxy for example. And the electronics/plastics of the display could be relatively fine with the low temps.
Click to expand...
Click to collapse
this is not one of them...i can guarantee this 100%
learn how a digitizer is made then you might see the light, and not just the light of white trash repair and failure...
ive explained it in great detail many times... and btw just because im a girl doesnt mean what im saying is wrong... 20+ years in the industry gives me sort of a clue as to what im saying..
im trying to help people avoid a long drawn out disaster and to waste $20(which is NOT gorilla glass) plus all of the other things they buy to try to make this a success which will never happen...
and fyi freezers, superglue and epoxys are big no no's...they are not used by any factory so there is another myth busted... they will just add to the destruction... 100% guarantee
kawgirlval69 said:
this is not one of them...i can guarantee this 100%
Click to expand...
Click to collapse
What do you mean? One of what?
learn how a digitizer is made then you might see the light, and not just the light of white trash repair and failure...
Click to expand...
Click to collapse
I know how a digitizer is made.
ive explained it in great detail many times... and btw just because im a girl doesnt mean what im saying is wrong... 20+ years in the industry gives me sort of a clue as to what im saying..
Click to expand...
Click to collapse
I had no idea you were a girl and I don't see why that matters. Experience is the industry is of course relevant, if your particular field in the industry was related to repairs. But I don't know if it is?
im trying to help people avoid a long drawn out disaster and to waste $20(which is NOT gorilla glass) plus all of the other things they buy to try to make this a success which will never happen...
Click to expand...
Click to collapse
The glass on the Note is Gorilla glass: http://www.corninggorillaglass.com/products-with-gorilla/full-products-list
and fyi freezers, superglue and epoxys are big no no's...they are not used by any factory so there is another myth busted... they will just add to the destruction... 100% guarantee
Click to expand...
Click to collapse
I didn't say factories use superglue or epoxy, or freezers for that matter. But the fact that factories don't use them doesn't mean it can't work for DIY repairs. Low temperature brittleness isn't exclusive to epoxy or superglue. Many, many glues (and other materials) have that property.
pboesboes said:
What do you mean? One of what?
I know how a digitizer is made.
I had no idea you were a girl and I don't see why that matters. Experience is the industry is of course relevant, if your particular field in the industry was related to repairs. But I don't know if it is?
The glass on the Note is Gorilla glass: http://www.corninggorillaglass.com/products-with-gorilla/full-products-list
I didn't say factories use superglue or epoxy, or freezers for that matter. But the fact that factories don't use them doesn't mean it can't work for DIY repairs. Low temperature brittleness isn't exclusive to epoxy or superglue. Many, many glues (and other materials) have that property.
Click to expand...
Click to collapse
i mean exactly what i wrote... as per your idea... this wasnt one that would work... my god man do i have to spell everything out for you???
obviously you dont know how a digitizer is made or you wouldnt have spouted the crap you have... bottom line
the girl part..well some dont think women know anything..its a culture thing.. but as for you not knowing if my particular field in the industry was related to repairs my god ive only said it multiple times in multiple posts... but since you dont like to read i'll say it again..20+ years board level factory trained.. motorola, audiovox, nokia, samsung... and this is a samsung forum so i think i have my tech qualifications covered here... again READING IS GOOD... work on that...
again you just dont read or have horrible comprehension because i never said the notes screen wasnt gorilla glass i said the $19 one wasnt... seriously every time you type something you dig yourself a deeper hole...
your superglue and epoxy blather just shows you dont have a clue and dont read... really they dont have any place in the screen/lcd part of diy.. its just trouble looking for a place to happen... now if the plastic housing needs repaired maybe but still not a top ten choice... if you had a clue you would know the proper adhesive to use... and its easily found... you are just too much...
seriously...just give it a rest... i wasnt bashing on you and have said it ive also said all im trying to do is help people not make a bad decision... and THIS IS A BAD DECISION...
you want me to play nice (which i really am..most other forums here would have totally lowered the boom on you for spouting crap... ive been really nice.. to keep it that way just go post somewhere where you can be productive... here youre not... im sure you have some great ideas but nothing you have said in this thread is remotely good.. sorry but it is what it is...
beep beep
kawgirlval69 said:
i mean exactly what i wrote... as per your idea... this wasnt one that would work... my god man do i have to spell everything out for you???
Click to expand...
Click to collapse
The sentence made no sense considering what it was replying to. Not my fault you were unclear/ambiguous.
obviously you dont know how a digitizer is made or you wouldnt have spouted the crap you have... bottom line
Click to expand...
Click to collapse
Ok?
the girl part..well some dont think women know anything..its a culture thing.. but as for you not knowing if my particular field in the industry was related to repairs my god ive only said it multiple times in multiple posts... but since you dont like to read i'll say it again..20+ years board level factory trained.. motorola, audiovox, nokia, samsung... and this is a samsung forum so i think i have my tech qualifications covered here... again READING IS GOOD... work on that...
Click to expand...
Click to collapse
Reading is very good, but you can't assume everyone in a public forum has read every single post of yours and remembers every detail. What isn't helping is the lack of proper punctuation and formatting which make your posts unpleasant to read.
again you just dont read or have horrible comprehension because i never said the notes screen wasnt gorilla glass i said the $19 one wasnt... seriously every time you type something you dig yourself a deeper hole...
Click to expand...
Click to collapse
Replacement screens are generally OEM parts.
It might appear I'm in a hole, but that's only because I live in Holland and am below sea level. I assure you I haven't done any digging.
your superglue and epoxy blather just shows you dont have a clue and dont read... really they dont have any place in the screen/lcd part of diy.. its just trouble looking for a place to happen... now if the plastic housing needs repaired maybe but still not a top ten choice... if you had a clue you would know the proper adhesive to use... and its easily found... you are just too much...
Click to expand...
Click to collapse
I wasn't suggesting to use superglue or epoxy, read it again.
seriously...just give it a rest... i wasnt bashing on you and have said it ive also said all im trying to do is help people not make a bad decision... and THIS IS A BAD DECISION
Click to expand...
Click to collapse
I get that, and appreciate your concern. However, you should understand that some people like to try things even when the chance of success is not very high. You seem to be one of us in that regard (you attempted repairs yourself too, right?), so I don't see why it upsets you so much.
you want me to play nice (which i really am..most other forums here would have totally lowered the boom on you for spouting crap... ive been really nice.. to keep it that way just go post somewhere where you can be productive... here youre not... im sure you have some great ideas but nothing you have said in this thread is remotely good.. sorry but it is what it is...
beep beep
Click to expand...
Click to collapse
I don't care if you play nice or not. I appreciate honesty. Now for some honesty in return: you're not helping in this thread.
All you do is say people's ideas are stupid without giving arguments that aren't arguments from authority. And I would very much appreciate it if you would stop misrepresenting my posts (intentional or not).
I have gathered up reports of the glass cracking by itself, and have come up with 6 reports already. Very concerning considering the availability of the phone. If you have a similar problem happening to you, please do post here, and if possible, please fill out this survey.
Thanks
Currently at 10 reports.
1. http://forum.xda-developers.com/showpost.php?p=55904325&postcount=7
2. http://forum.xda-developers.com/showpost.php?p=55861318&postcount=14 / http://forum.xda-developers.com/showpost.php?p=55861158&postcount=34
3/4. http://talk.sonymobile.com/t5/Xperi...cked-shattered-on-it-s-own/m-p/844031#U844031 (2 posts in this)
5/6. http://talk.sonymobile.com/t5/Xperia-Z3-Compact/Cracked-screen/m-p/843849#U843849 (2 posts in this)
7. http://talk.sonymobile.com/t5/Xperia-Z3-Compact/Cracked-screen/m-p/843849#U843849
8. http://www.reddit.com/r/SonyXperia/comments/2iv7sq/z3c_back_glass_cracked_eta_on_replacement_parts/
9. http://talk.sonymobile.com/t5/Xperia-Z3-Compact/Probable-PRODUCTION-FAULT-glass-broke-from-2cm-drop-add-your/m-p/846827/highlight/true#M525
10. http://talk.sonymobile.com/t5/Xperia-Z3-Compact/Probable-PRODUCTION-FAULT-glass-broke-from-2cm-drop-add-your/m-p/849689/highlight/true#M636
Lets say they sold 1000 phones so far, I would guess more but lets be very conservative. 6 "cracking by itself" in 1000 phones = .6% chance
I think we should post on this over and over since it is such a huge chance of happening.
Two of those are also the same person.
The screen is ridiculous flimsy. Putting pressure on the screen easily distorts the display. Sony went cheap with the glass. Don't sit on it, that's for sure.
maven1975 said:
The screen is ridiculous flimsy. Putting pressure on the screen easily distorts the display. Sony went cheap with the glass. Don't sit on it, that's for sure.
Click to expand...
Click to collapse
Lulz. Don't forcible bend you're phone and don't sit on it. Grade A advice.
Also, if you're Z3C is that flimsy, return it, cause mine certainly isn't that flimsy.
Crewville96 said:
Lulz. Don't forcible bend you're phone and don't sit on it. Grade A advice.
Also, if you're Z3C is that flimsy, return it, cause mine certainly isn't that flimsy.
Click to expand...
Click to collapse
Mine is solid too. No flex or distortion at all. And I would say 0.6% is a bit high. Their total sales are probably greater than 1000 by now. Probably closer to 1500 so that's more like .03 - .04%
But not all the 1500 user complain on XDA or the web...
Crewville96 said:
Lulz. Don't forcible bend you're phone and don't sit on it. Grade A advice.
Also, if you're Z3C is that flimsy, return it, cause mine certainly isn't that flimsy.
Click to expand...
Click to collapse
Who said anything about bending?
There are YouTube videos showing the issues with the screen/glass.
I am receiving a second Z3C in the office Friday. I will check it report back.
As for sitting on a phone, this should not be an issue. Everyone is acting as if this was never acceptable practice. I understand that things have changed and phones are getting thinner. However, would you not think a portable compact phone should be purchased for pocketability? I think it's outrageous people are so quick to dismiss and write off this simple and basic concept. And for what? For the sake of being a fan of a company that only wants your money? Apple, Sony, Samsung... They don't give a crap about the consumer.
Pocketability, to me, has never meant you can put a glass phone in your rear pocket.
maven1975 said:
Who said anything about bending?
There are YouTube videos showing the issues with the screen/glass.
I am receiving a second Z3C in the office Friday. I will check it report back.
As for sitting on a phone, this should not be an issue. Everyone is acting as if this was never acceptable practice. I understand that things have changed and phones are getting thinner. However, would you not think a portable compact phone should be purchased for pocketability? I think it's outrageous people are so quick to dismiss and write off this simple and basic concept. And for what? For the sake of being a fan of a company that only wants your money? Apple, Sony, Samsung... They don't give a crap about the consumer.
Click to expand...
Click to collapse
WHY would you put your phone in your rear pocket and sit on it? It's bad for your back and CERTAINLY bad for any thin piece of technology with glass on it!
Not to mention rear pockets are easy targets for pick pockets...
degraaff said:
WHY would you put your phone in your rear pocket and sit on it? It's bad for your back and CERTAINLY bad for any thin piece of technology with glass on it!
Not to mention rear pockets are easy targets for pick pockets...
Click to expand...
Click to collapse
I'm not concerned about pick pockets. If they want my phone, the could take it from my hands just as easily. So, I guess we are not to put our wallets in our rear pocket either?
I don't sit on it for long periods of time. More time than not, it is out of my pocket while seated. The issue I have is with these excuses for manufactures. I'm not starting a lawsuit or demanding a refund. I'm simply just annoyed by the arrogance displayed. Pointing the finger at consumers for using said devices the way they have been used for years.
I can see the phablet argument. Those devices should not be on your pockets. (brief periods of time) But seriously, a compact phone that risks damage by pocket? That's hardly looking at the real audience your catering too.
Its not damage by pocket. Its damage by weight and force.
Sent from my Nexus 5
My rear glass cracked by itself. I have had my phone since launch (2 weeks now), and used it with care. There was not a single (micro-) scratch on it (no protection), never dropped or otherwise misused. So as to the reports they are scratchy - imho that's not true.
I put the phone on my desk, picked it up 30 minutes later, and noticed the rear glass was cracked. Picture attached. As you can see this is not the kind of cracking you get from dropping, smashing, or putting tension on it. The crack is beneath the surface - I can't feel it. The phone is on it's way back to the shop now, and I'll hope it will be a warranty thing.
Also, on a major Dutch tech-forum there are several stories about cracking glass (3 or 4 now, did't keep count).
It's a real thing! :crying:
CollinsJ said:
Lets say they sold 1000 phones so far
Click to expand...
Click to collapse
Then they'd better shut down their smartphone department considering Apple sold 10 million units on the first weekend and the Z3C got really good previews :cyclops:
Please stop this discussion on back pockets, whether or not that pocket is suitable for phones is not for discussion here. All the reports I posted said front pockets, and that is concerning.
JorgV said:
My rear glass cracked by itself. I have had my phone since launch (2 weeks now), and used it with care. There was not a single (micro-) scratch on it (no protection), never dropped or otherwise misused. So as to the reports they are scratchy - imho that's not true.
I put the phone on my desk, picked it up 30 minutes later, and noticed the rear glass was cracked. Picture attached. As you can see this is not the kind of cracking you get from dropping, smashing, or putting tension on it. The crack is beneath the surface - I can't feel it. The phone is on it's way back to the shop now, and I'll hope it will be a warranty thing.
Also, on a major Dutch tech-forum there are several stories about cracking glass (3 or 4 now, did't keep count).
It's a real thing! :crying:
Click to expand...
Click to collapse
So I take it that the phone wasn't cracked before putting on the table? Did you something on the phone before that could have caused it to heat up?
I've put together a Google forms survey to collect some objective breakage data:
Sony Xperia Z3 / Z3 Compact - Glass Survey
Please take some time to complete the survey whether you've experienced a breakage or not, it's important to have a complete set of data. You will be able to view the survey results after submitting the form.
darkgoon3r96 said:
So I take it that the phone wasn't cracked before putting on the table? Did you something on the phone before that could have caused it to heat up?
Click to expand...
Click to collapse
No, I'm quite sure it wasn't. As far as I know it was idle, just being stand-by .
"spontaneous crack"
like all the screen cracks ive seen before. Most of the time the user actually cracked it (fall, sit on it, etc.. but mostly falls where "oh im lucky nothing broke") and with some more use the crack propagated. yeah with plastic or metal it woulnt propagate tho.
bilboa1 said:
"spontaneous crack"
like all the screen cracks ive seen before. Most of the time the user actually cracked it (fall, sit on it, etc.. but mostly falls where "oh im lucky nothing broke") and with some more use the crack propagated. yeah with plastic or metal it woulnt propagate tho.
Click to expand...
Click to collapse
Yeah, until someone is watching at the exact moment their phone spontaneously cracks, I'm not believing it. The way some people talk about the Z3C is like if you breathe on it too hard it will shatter instantaneously. My wife dropped her's from chest height onto hardwood floor with no case, screen protector, nothing. Not a scratch. Yet other people, drop it from a foot up, or having it leaning an it just tips over, and breaks... seems odd. Not calling these people liars, just that there must be more to it than that. Probably something along the lines of what bilboa1 said.
By me and my cat.
Kinda simple, really, once youll get this nice tool for opening the phone.
It seems that the dust gets inside through some small openings in the round lens protector, as the rest of the insides are really clean.
Anyway, enjoy
https://youtu.be/iCGr3we1SKQ
SmartPhonesFan said:
Nobody has dust in cameras..
Click to expand...
Click to collapse
Stop **** posting , it is a common problem to get dust in your camera lense with this phone .
k4syx said:
By me and my cat.
Kinda simple, really, once youll get this nice tool for opening the phone.
It seems that the dust gets inside through some small openings in the round lens protector, as the rest of the insides are really clean.
Anyway, enjoy
https://youtu.be/iCGr3we1SKQ
Click to expand...
Click to collapse
same here no dust!
SmartPhonesFan said:
what? it is ABSOLUTELY NOT COMMON PROBLEM YOU STOP SPREADING FALSE INFORMATION .. YOU ONLY HAVE DUST
GOD KNOWS U BEEN DOING WITH IT! IF U HAVE DUST WHY THE F** U DIDN'T CLAIM WARRANTY??
ARE U FOR REAL?? U DON'T KNOW PROCEDURE?? INSTEAD U TAKLONG HERE OPENING PHONE?? U OPENED PHONE B4 AND NOW U COMPLAINING ABOUT DUST.. JEEEZZ
Click to expand...
Click to collapse
IKAN USE MYKAPS TOOOONEONEONE!!111
Please do stop shouting at all of us and accusing me of spreading false information. Dust under my lens protector - and the one that you can see in youtube video by this russian guy - was pretty real.
There is a problem with some Honor Note 10 units. There are - not always, not with every unit - ver small gaps around lens protector glass. If you will clean your phone with cloth (or your shirt etc) there will be a small dust particles buildup in time.
In my case it took almost four months and I am not the first nor the only case - just look around the web.
As for warranty claims. You gotta be kidding - you seriuosly think that I'd ship my phone around the globe, from Europe to Asia, because of something that I can fix in ten minutes by myself?
C'mon, that's just lame. Anyone with two good hands can do this himself.
And I think in someone already tried to claim warranty on that - to no avail.
If you dont have the dust there (yet?) then I am happy for you and I can even send you some kind of postcard with congrats for that.
Or if you happen to have two left hands or just like to claim warranty for any silly reason: go for it! Go go go!
Or buy new phone, whatever, I don't really care
But if you DO will notice this dust, feel free to use my guide on how to fix this problem
Well I did have this problem, and I am freely trying to help others with this issue fix it by themselves, in 10-15 minutes, without sending phone back (which would take 30-45 for trip both ways not even counting the money involved).
Which one of this things exactly trips you off?
Me trying to help others, or the fact that this can be fixed without refund/sending back the phone that someone may like like I like my piece?
If you'll do this in reasonable clean room (as you'd be applying screen protector) there will be no additional dust. And I'm saying in my vid that air duster is handy.
There already is a gasket under the back plate that goes around the lenses. It is some kind of flexible foam and you can see it in my video.
As for shattering the glass - yes, I suppose that someone could do that, but you'd really had to work for it, and I am saying in my vid that you need a sucking tool to pry open back plate.