Database Develop

Help.. .Killed my Qtek... PC BSD durning ROM Update

So, I have updated my ROM many a time, and was updating my qtek wizard with the 2.17 WWE rom, at 3% through, my PC does a Blue Screen of death... Now my wizard is just locked at the Color Bar screen saying IPL 2.17 and SPL 2.17.
DID I KILL IT?

sdattilo said:
So, I have updated my ROM many a time, and was updating my qtek wizard with the 2.17 WWE rom, at 3% through, my PC does a Blue Screen of death... Now my wizard is just locked at the Color Bar screen saying IPL 2.17 and SPL 2.17.
DID I KILL IT?
Click to expand...
Click to collapse
No you didn't kill it. =)
Take the battery out, and put it back in.
Hold down the Camera button while pressing the power button
You should be back to the three color bar screen
Connect to your PC using the USB cable
Run ROM upgrade
That should fix it. Make sure you don't have anything running on your PC during the upgrade. The only time I've ever bluescreened during a ROM upgrade is when I was playing MP3s in the background.

summiter said:
sdattilo said:
So, I have updated my ROM many a time, and was updating my qtek wizard with the 2.17 WWE rom, at 3% through, my PC does a Blue Screen of death... Now my wizard is just locked at the Color Bar screen saying IPL 2.17 and SPL 2.17.
DID I KILL IT?
Click to expand...
Click to collapse
No you didn't kill it. =)
Take the battery out, and put it back in.
Hold down the Camera button while pressing the power button
You should be back to the three color bar screen
Connect to your PC using the USB cable
Run ROM upgrade
That should fix it. Make sure you don't have anything running on your PC during the upgrade. The only time I've ever bluescreened during a ROM upgrade is when I was playing MP3s in the background.
Click to expand...
Click to collapse
Exactly this solution works fine with me!

three color bars on tmobile MDA
Hi,
I tried a hard reset with pressing camera button and power button together but it comes on with a three color bars
RRU
IPL 1.01
SPL 2.26
USB
But while flashing new ROM it says there is a connection problem with the PDA and yes, it does not show connected on Active Snyc 4.5...
Any help how to flush it with any ROM. I also tried to download the Tmobile software but it agains says the phone is not connected with USB.
When I connect the phone wiht USB, computer makes beep like somthing is connected....I can not figureout what is wrong.....any help???
thnx

My 8125 Frozen on Cingular splash screen

Hey everyone, i couldnt find any information that helped me so i thought i would let you all know my problem. when i turn the phone on it freezes on the cingular splash screen and my ipl is 2.25, spl 2.25, gsm 02.25.11, os 2.25.11.1. When i go to the red blue green screen, my usb connection shows up on the white part, but when i try to install the official cingular rom it doesnt connect. it says that i need to make sure that i have a usb connection. then the screen goes white. any sugesstions?

tarusdg said:
Hey everyone, i couldnt find any information that helped me so i thought i would let you all know my problem. when i turn the phone on it freezes on the cingular splash screen and my ipl is 2.25, spl 2.25, gsm 02.25.11, os 2.25.11.1. When i go to the red blue green screen, my usb connection shows up on the white part, but when i try to install the official cingular rom it doesnt connect. it says that i need to make sure that i have a usb connection. then the screen goes white. any sugesstions?
Click to expand...
Click to collapse
Which Windows are you using ? if you are at WinVista it won't work,always use WinXP,secondly do the following :-
1. Disconnect your phone from the usb cable,shut down any firewall,disable any Anti virus,Reboot your PC.
2. On your Desktop PC, open Microsoft ActiveSync, then go to File >Connection Settings >Remove the Selection from “Allow USB Connection with this desktop computer”
3. On your PC Open windows Task Manager...>Tab Processes...>wescomm.exe...>End process
4. Power off the phone completely (Not stand-by,shut off completely),or you may take the battery out for few seconds
5. Make sure your phone is not Connected to the PC via USB cable and remove the dummy Sdcard or mini-Sd card
6. Get your phone into Bootloader mode (Multicolor screen) by pressing camera button + Power on button
7. Reconnect your phone to the Desktop PC using the USB Cradle and the Charger MUST be Connected to the Cradle (Be sure that your battery is charged over 70%)
8. "USB"will appear on the bottom of the screen of the Bootloader (Multicolor screen)
9. Run the Upgrade again and it will work fine without any problems.
10.Never use Bluetooth sync for the Upgrade
While upgrading, the ActiveSync program will not go on, however the upgrade is running.Please be patient when you're flashing your device, even if 98%. It can wait a little bit, 5 ~ 7 minutes.
Don't cancell the flash or get the phone off the usb cable till it confirms "Congratulations" or stops with an Error!!!
Hope it'll work,
Cheers

i dont have a cradle just the usb cable. will tha be a problem?

i tried it with just the usb cable and it didnt work
any other suggestions?

it is time to junk it or donate to XDA-developers

...fades to white screen upon connection
I have a similar issue...my 8125 Wizard gets stuck on the splash screen. I follow the above procedure to the letter, get into Bootloader, make the USB connection, and then when I try to flash ANY ROM as it starts to connect the screen fades to white and it comes back with Error 274...Connection error! It doesn't matter what ROM I try...Button's 1.05, Love ROM, T-mobile 2.26, or the Cingular 2.25 ROM...the screen fades to white as it starts to connect. Any ideas Doc P?
The splash screen says:
IPL 2.25
SPL 2.25
GSM 2.25.11
OS 2.25.11.1
BTW, i've tried the MTTY_updateROM.exe ...miniSD card ...r2sd all approach ...the device is CID locked...

[Solved]Still no Brick!!!

Hi People
I think I have really bricked my Diamond for sure. I have read all the threads related to this problem and have tried all the possible fixes but to no avail.
Here is the problem: It is stuck on the first screen after tri colour screen showing the RGD info in red ink at the bottom right cornor. Pc wont recognize it and Active Sync 4.5 on xp is grey, not green.
I have done a few Hard resets and Soft resets. I have Olinex Hard Spl installed. Had Dutty's 1.6 working perfectly when decided to cook my own with Surface Kitchen. My first cooked rom worked fine and then I cooked another one with same base Stock rom , adding som programs and bam, this thing happened.
Please Help Help and yes I had flashed the same Diamond with every available cooked rom with no problem.
Thanks in advance. Lets not Die this beautiful Jewel.

Anyone please?

tararura said:
Anyone please?
Click to expand...
Click to collapse
Can you get it into bootloader mode??? If so, you should be fine to re-flash at that point.

I can get it to tri colour screen but it wont sync with pc ...?

tararura said:
I can get it to tri colour screen but it wont sync with pc ...?
Click to expand...
Click to collapse
So after getting to the tri-color screen and then plugging in the USB cable, you do not get "USB" at the bottom of the screen?????

Thanks for the quick reply..
Ok here is what I am doing. I perform the hard reset. Get the tri colour screen for couple of seconds and then it comes to the screen where it asks to press Volup to restore. I did it with the usb connected and usb disconnected but it wont sync. Active sync icon at the bottom on pc stays grey not green.
Pressing Volup on diamond restores, reboots and brings it back to 1st splash screen with RGD info at the bottom in red ink. aaaaah

When you are in bootscreen, connect via usb.
In the bottom off your screen you should see "usb"!
If this is what you see then flash one of the stock roms again.
After you've done this, your Diamond restarts and everything should be OK again!
Good luck!

Ok, do this:
1. Unplug the USB cable from the phone.
2. Hold down the Volume-down key and the Power button, then press (and let go of) the RESET button with your stylus.
3. When the tri-color screen appears, you can let go of the buttons.
4. The screen should say "Serial" at the bottom (in the gray color area).
5. Plug in the USB cable (The screen should change to "USB").
6. Run the RUU app to re-flash the phone.
That should get you back up and running.

To enter bootloader, turn phone off then press volume down and reset simultaneously and then power ono. If you have done this correctly it will remain there and the word "serial" appears at the bottom. Then plug in USB and the word changes to "USB" you can now flash ROM

When I flashed mine it also got stuck te first time because Windows found it necessary to install new USB driver when the Flash util wanted to connect to the HTC. The flash program jumped out leaving the diamond with the RGB screen...
But, after windows installed the new USB driver, I restarted the flash program and it finished just fine.
So if you cannot connect anymore I would try to find out if the USB driver has changed. Did you try connecting to another USB port?
Otherwise I would try to connect to another PC...
Hope it helps,
Beamer

fingers crossed
hope you unbricked it m8

@tararura
Be sure to come back and update the thread if you were successful. It may help others later if they search instead of starting another thread with a similar problem.

Holy smokes......
Its breathing again. Thank you TomInMB and Windoze9t8. Give yourselves a kiss for helping me out.
I used Windoze9t8's method and it came to the serial screen and then I flashed it with Dutty's.
So I was using hard reset method to get to bootloader screen, which was wrong.
So for everyone else, its Voldown and reset button at the same time for Bootloader screen.
Flashing is done and Active Sync recognized the Diamond.
Thanks again for everyone..... and I am sure that a few of us learnt the new trick from this thread.....

Glad to hear you're all set!!!! I sure would hate to have the feeling that my precious diamond was useless!!!!

Thats right , I already lost a lots of sleep trying to fix it last night..

[HELP] Is my Diamond dead? (for advanced users)

Hello,
Today my Diamond probably died.. in fact it is MDA Compact IV.
I got new battery from ebay (original 1340mah from HTC). I put new battery to MDA but it didn't start. I tried to plug charger, but there is all time such situation:
- d-pad shine twice like during charging,
- one vibra ring
- splash screens
- turn off after about 10 seconds
I change battery with old one but there is the same problem.
I can make Hard Reset, I can enter bootloader mode, but nothing more.
Vibra, splash, reset again and again. If I pull off charger- phone is dead, there is no possibility to switch on.
Does anybody know such problem? Is there any solution? I read somewhere that is probably dead mainboard, is it true?
Please somebody help me, I got my MDA only one week
There was warranty but I installed HardSPL and unofficial ROM, so I can't turn it to service

Does the phone reset when you're in bootloader as well?

No, I can enter bootloader mode.
I have such words on screen:
DIAM200 MFG 64M
SPL-1.40.OliNex
MicroP-Diam (LED) v11
PSOC-Vict STAGE_PVT v0x20
USB.
It stays in bootloader. I can quit bootloader by soft reset. If I pull charger off then Diamond turns off.

you sure no liquid went in? or any falls?
if not - probably a faulty ROM or Radio... what you can try to do is first fully charge your phone (just keep it turned off and attached to charger).
once charged fully (you can tell by the d-pad light) when in bootloader, connect it to USB to your computer. it should change from Serial to USB on your phone. then flash a radio (preferably the one that came stock) via the Custom RUU method.
if that doesn't work... repeat steps above for a ROM...
and make sure u keep your fingers crossed good luck!

Ok, situation for today looks this way:
1. I can't turn the phone ON.
2. If I connect phone to charger or PC phone turns ON. There is one vibra ring and splash screen without numbers in corner (ROM, radio etc). Splash screen in ON for about 10-12 second, then phone is rebooting. It going all around continuously.
3. During displaying splash screen I CAN enter bootloader mode or make hard reset. If I enter to bootloader and plug charger off then phone turns OFF.
In bootloader mode there is such text on display:
DIAM200 MFG 64M
SPL- 1.40. OliNex
MicroP-Diam (LED) v11
pSOC-Vict STAGE_PVT v0x20
USB.
Windows in my PC makes sound as connected UBS equipment, but ActiveSync is not connected (grey).
4. After running bootloader mode I CAN run DiamondCustomRUU.exe. It looks like updates, ROM, Radios are installed- indicator is running in my PC and also on Diamond screen. After finishing installation there is again: reset, vibra, splash screen 10-12 second, reset, vibra... etc.
I tried to install many ROM, Radios and all SPL but final is always the same.
5. I tried to install original SPL- installation looks successful, but after reset in bootloader mode there is still: SPL- 1.40. OliNex. This point is most strange for me.
6. I can connect via mtty (but activesync is still gray), but I don't know commands for mtty and I don't know what more can I do through mtty.
For me right now most important is to turn SPL back- then I can return device to service.
Does anybody knows some solutions? I'm opened for any suggestions...
Thanks,

go and stay in boot loader mode (tri-stripe colored bands) and flash with custom ruu another rom, have you tried this simple step?
EDIT: sorry I read right now you tried, so bad, so unlucky!

Seems like the battery contacts on Ur device are faulty - The gold plating might have worn out and the contact with battery terminals is bad, so device registers critical battery and shuts off.
Try cleaning the contacts with a piece cotton or a soft cloth soaked in alcohol on all the contacts. (avoid too much - should not enter the device!!)

Could you try charging your battery without phone?

Need Help

My hTC HD7 is not reading the usb cable in the "red,blue,green,white screen"
is not setting "serial" or " USB" in the white border
but when i tur on my device and plug in the pc reds the usb and my phone
i have reset my phone and the phone is reset but still not read the usb cable on the "RED , Green, Blue, White" screen
sorry for my english :S

If you use the search button...
you'll find that I already answered this:
Goldcard method is the only option to downgrade this and get a fully functional bootloader.