Error upgrading Voda 1605 to WM6 - P3600 Software Upgrading

I have upgraded from a Hermes to Kaiser (Voda 1605 to 1615) and hence am trying to upgrade my Hermes to WM6 using the official HTC ROM.
It al starts perfectly fine, but after the Installshield wizard starts, and after I accept everything the screens asks for I get a message saying that there is a problem with the connectivity. The Error number I get is 264.
I tried a hard reset and then de-activated all the programs on my laptop like firewall, antivirus, antispyware etc, in fact I disabled everything from the startup tab in msconfig.exe and restarted the whole process, but still the same problem and same error number.
Has anybody else encountered similar problem? Any help will be appreciated.

Related

WM5: Unable to sync through USB in ActiveSync 4.0

Please, help!
I am unable to persuade my AS 4.0 sync with my newly upgraded mda III. If I downgrade to wm2003SE, it works again, but when I try wm5, it does not do anything. Sometimes there is a signal: the first sound of the upwards connection signal three times, then nothing happens.
When I first upgraded to wm5, a found new hardware appeared and intended to go to the net for some driver. I said OK, then the installation failed after a few seconds. That was the only occassion of any real activity between the MDA III and AS4.
Via Infrared, it works fine, but it is very slow.
Any idea? Or any forum about this, I really tried to find one but found nothign so far.
Thanks a lot!
barrney said:
Please, help!
I am unable to persuade my AS 4.0 sync with my newly upgraded mda III. If I downgrade to wm2003SE, it works again, but when I try wm5, it does not do anything. Sometimes there is a signal: the first sound of the upwards connection signal three times, then nothing happens.
When I first upgraded to wm5, a found new hardware appeared and intended to go to the net for some driver. I said OK, then the installation failed after a few seconds. That was the only occassion of any real activity between the MDA III and AS4.
Via Infrared, it works fine, but it is very slow.
Any idea? Or any forum about this, I really tried to find one but found nothign so far.
Thanks a lot!
Click to expand...
Click to collapse
Have you read the WiKi about setting the IP and disabling the firewall?

spontaneous soft reset every so many minutes

Hello,
My T-Mobile MDA Vario spoke Dutch which was very unformortable so I unlocked it and installed the Qtek ROM. Installation was fine.
However, it kept on being confused about the state of the "flight mode"; either I could make phone calls even though the icon said it was not connected to the network (aerial with X) or it did not want to connect to GPRS even though it was on the T-Mobile network
Otherwise it all worked fine.
In an attempt to get rid of this annoying behaviour I installed the K-Jam ROM found on the FTP server of this website. Installation was fine again, however now the device soft resets itself all the time and does not always want to turn on when I push the button on top. The soft reset frequency is very unpredictable, and turning phone on or off does not really make a difference.
Any clue?
Many thanks in advance
Manhattan.
It looks like the reset problem is solved after installing an updated i-mate ROM that resides in the upload section of this site's FTP. It seems to me it has only an updated extended rom part, perhaps someone has figured out what's the difference?
thanks
manhattan
what's the filename? i couldn't find it...
K-JAM_WWE_1010903_106_10110_ship.exe

Problem when upgrading from TuMa v1.3 to Helmi, no phone?

Hey All-
Rather then adding to the large Helmi thread, I figured it would be best to start my own...
In short today I upgraded from TuMa v1.3 to Helmi's new ROM: Helmi_BA_WM2k5_AKU_2.3_32mb_v1.rar
Everything went fine during the upgrade, I set the Operator Code to T%CID? which was retrieved by using GetDeviceData.exe and the upgrade went smoothly... but now the phone functionality doesn't work at all. I've tried with two different SIM's, one being a T-Mobile and the other a Cingular. Both just show no service when inserted, although if I place those SIM's into other phones everything works properly without issue and I get 'full bars' (I have another Cingular 8125 and a T-Mobile SDA).
Here is what I have done so far:
- Reupgraded the Radio to the latest rev 1.15
- Recreated the nk.nbf again with retyping the operator code
- Reupgraded to the ROM to Helmi's
- Reunlocked SIM with xdadev_all_unlock-v1.5.exe
... and still no phone service.
Any suggestions on how to get the phone functionality to work properly? Its pretty much useless right now...
Thanks!
tempie23
I'm not sure that T%CID is right for an operator code... I know for O2 UK it's O2___001 and I'm sure a T-Mobile code isT-MOB101, both of these are 8 digits... check you're devicedata output again and use the setoperator.bat to set it properly, then try again
It's all good clean fun
spkr4thdd
I have the same operator code T%CID? but only on WM5. When i use 2003SE it is DANGA001.
tempie23
I had such error on TuMa 1.4 but reinstalling the ROM helped for a while. Then I tried helmi's ROM and the problem gone. But a couple of days ago it appeared once and reflashing did not help. What I done is downgraded to 2003SE, did a hardreset and reinserted SIM. The phone came back to work. Then installed helmi's ROM again. Now it is working for a day without any trouble, HOPE it's gone forever.
Tried a few things...
I tried downgrading and then reupgrading, but it still is stuck. No phone service. Interestingly enough the LED for the phone doesn't even come on anymore.
Interestingly enough when I select the phone settings from the upper menu I'm getting a Popup message stating "The phone is not ready. Wait 15 Seconds and try again." Obviously waiting 15 seconds does nothing...
Any other ideas?
Thanks!
tempie23
sometimes (happened to me) the operator info corrupts when upgrading to WM5
copy the files attached to the update directory and run 'MaUpgradeUt_noID.exe'
spkr4thdd said:
I'm not sure that T%CID is right for an operator code... I know for O2 UK it's O2___001 and I'm sure a T-Mobile code isT-MOB101, both of these are 8 digits... check you're devicedata output again and use the setoperator.bat to set it properly, then try again
It's all good clean fun
Click to expand...
Click to collapse
No it is not, it sounds like he has the same SX 66 that I have.
The ID is = AT%CID?
I posted this in this thead Here
read my above post, it can happen to anyone when upgrading to any wm5, mine happened the very first time i upgraded (TuMa 1.3), i dont know how it happens, but it seems to be permanent even with further reflashes (haven't tried 2k3)
NO Service
Midget_1990 said:
read my above post, it can happen to anyone when upgrading to any wm5, mine happened the very first time i upgraded (TuMa 1.3), i dont know how it happens, but it seems to be permanent even with further reflashes (haven't tried 2k3)
Click to expand...
Click to collapse
HI.
Sorry for my post, but I did not "get" how to fix the "NO Service" error:
This is what I've done today with Helmi_BA_WM2k5_AKU3.5_v1.4.CF2 by baniaczek:
Hi all.
Today finally spent some time, trying to upgrade my Qtek 9090.
Everything went fine:
1st) Did a SD backup of my current settings;
2nd) Updated ROM with SetOperator to my Operator (got from getdevice.txt);
2nd) Updated without problems;
Then used the Qtek by 5 minutes (inclusively i did a phone call), after that could no longer get the "phone" working - exactly when I received a call, the phone "gone out" and never more. After several soft resets and hard resets the phone was always with "no service" message (but strangely, I could go to settings phone, and look for "the broadcasting" networks).
I swaped the SIM to another phone and it was working, never the less I got another working sim, but the problem continues (btw, I always have the PinCode disabled, and I remember now that I forgot to test enabling PinCode request!!!).
Then, just in case I downgraded the phone to W2003SE, again, and everything was working fine.
My radio was 1.12. So upgraded radio to 1.15, and started over again but with no sucess.
When I downgraded once again, the Qtek works fine with either RADIO versions or sims.
Has anyone got this "nice feature"?????
Is there any overcame solution? (My only missing test is to enable Pincode, and test if it works?)
tks for any help
I'm having the same issue here as well, tried the comm manger on and off and disable and enable it. Still makes no difference, someone please help me out, I can't get anyone to help me

activesyn problem in 1.93ROM

Did anybody notice an improvement in activesyn?
My ROM is 1.93.831.1.
The activesyn. is still unstable. It fails intermittently and usually needs a soft reset before it can succeed.
But after repeated reset, sometimes the favorite contact list would be cleared up. How come there is still bug???
What is HTC doing?????
I am feeling desperate.
My old PPC 2003SE can even do activesyn within 10-20sec but diamond need at least ~1min to do so!!!
Switching off "enable advanced network functionality" seems to work in 1.34 ROM but not in 1.93 ROM.

HTC Touch Diamond can't connect to Vodafone (Ireland) emailplus

I recently bought my HTC touch diamond on ebay running windows mobile 6.1 and set up Vodafone irelands emailplus (push email) which worked fine for first few weeks.
Now it won't connect
I can connect to internet via GPS no problem and have downloaded software a few times already
I install software and on first run it tries to connect and tells me theres been an unexpected error in connection and asks if I want to try again
I have uninstalled and reinstalled a few times but no joy.... (it can't seem to connect to intiate setup)
Called Vodafone a few times who, apart from doin telling me to do the above and checking I was set up there end, are now saying it's a hardware problem and because phone wasn't supplied by them they can do no more
I don't think it's a hardware problem...
I'd be very greatful if anyone has a fix for this as having push email was one of the reasons for getting the phone

Categories

Resources