Okay, so I just recently flashed to Touch-IT 4.4 by itje, and it's been working great. However, I just softreset my phone and now it's stuck in a boot loop just after finishing with the first splash with the text Touch-IT in silver..
It should probably be said that it reboots by itself, which I don 't think is normal for a bricked phone?
So I'm a bit stuck and don't really know what to do; Is my phone bricked (in which case I'll just have to unbrick it, which isn't a problem since there's a certain good guide that explain how to and I've already used it once), or what's wrong with my phone?
Meh, turns out it's possible to flash it with the hacked installer as well.. So I'm just going to reinstall the phone.
I just have one thing to say to all of you guys doing all this work on the ROM of Herald/Wing:
YOU. ****ING. ROCK. <3
Debdrup said:
Okay, so I just recently flashed to Touch-IT 4.4 by itje, and it's been working great. However, I just softreset my phone and now it's stuck in a boot loop just after finishing with the first splash with the text Touch-IT in silver..
It should probably be said that it reboots by itself, which I don 't think is normal for a bricked phone?
So I'm a bit stuck and don't really know what to do; Is my phone bricked (in which case I'll just have to unbrick it, which isn't a problem since there's a certain good guide that explain how to and I've already used it once), or what's wrong with my phone?
Meh, turns out it's possible to flash it with the hacked installer as well.. So I'm just going to reinstall the phone.
Click to expand...
Click to collapse
Take out your mSD card while rebooting and your device will start up fine
Is it the card that's doing it? Because I've soft-reset before without problems just fine. <.<
Gaah, I wish I had known that (or waited, but I was in a hurry to get my phone up and running again because I was expecting a call)..
It's not the cards fault. Somewhere here in the forum it was briefly discussed, but I can't find it right now.
It was said, that a certain DLL for SDHC support causes the looping.
It's called something like omap650sdhc.dll or so (you need to find out yourself, should be easy)
and by deleting or renaming it, it should solve the whole problem.
Never tested it myself, but it will not harm your device if you delete/rename that file.
That's the driver for the SD card drive... Depending on the rom you're using, it might be stuck inside the rom so you can't delete the file.
I asked Chikenbull on here to make a program that will rename that Omap file and reboot the device. I haven't tested it yet, but here it is.
Remember to use this AT YOUR OWN RISK.
GAMBIT999 said:
Take out your mSD card while rebooting and your device will start up fine
Click to expand...
Click to collapse
I've been doing this for the last month to avoid a HardReset. I've been having the boot-loop problem since i installed the HTChomeCustomizerV80 and/or HTCplus, and read about the warning too late: http://forum.xda-developers.com/showthread.php?t=326689
I've since removed the Today plugins, and the only annoyance remaining are the Backlight adjust function not working, and having to remove the microsd everytime I restart/power-on the Wing.
As I said, I'm trying to avoid a Hard Reset because I have 30+ programs installed and it's gonna take me a few days to reinstall all of them. I searched here with no success... all I found are the same saying "remove microSD at boot", which is what I'm doing, but it's a pain.
Tried GAMBIT999's suggestion, but can't remove omap850sdhc.dll from the \windows\ folder. Would DUPRADEE's suggestion of renaming this file with the program solve the restart-loop problem? Or is there other methods I haven't found, that'll save me the trouble of a Hard reset?
-cheers
edit: PROBLEM SOLVED!! thanks duprade
omap850sdhc.dll couldn't be deleted, but just changing the extension to omap850sdhc.000 solved the problem!!! Now I can restart without taking out the microSD!!! w00t w00t w00t !!!
Check for errors under Windows
One more possibility I forgot to mention which work fine for me.
After having the boot-loop symptom I took out my mSD card and checked it for errors under Windows.
I let Windows fix the errors and everything worked fine afterwards.
The procedure didn't took long even on a non USB2.0 port.
No card removing or file renaming anymore.
Folks having the boot-loop may try this solution out first before renaming/deleting the DLL.
My problem was SOLVED by simply renaming \Windows\omap850_sdhc.dll
It's funny how if you do not know the cause of the problem, SEARCH is useless. But once you find the answer (thanks Gambit999 and Duprade), going back to Search turns up pages of the same question posted over and over.
Anyways, credit goes to Paul at MoDaCo who found the solution on June 26:
http://www.modaco.com/content/HTC-Atlas-Atlas-MoDaCo-com/256186/Continuous-reboots-/
Changing to a blank new SD did nothing... but by Renaming the file, the PPC will reload the uncorrupted file from the ROM.
pls help
Its impossible to change the name or delete the file!
Pls help me!
p4350 wm 6
Thanks and pls sorry for my english!acces deniend its the reason to no rename!
I have had the same problem.This time after softreset for some Memmaid tweaks.The 1st.time It didnt occur to me to remove sd. and I'm certainly glad this works but heres the prob.After reinserting my 1gb.sd.I now have a file for Storage card & Storage card2.with 2 being the actual card.I cant remove or rename this file and cant launch apps.unless i do so through file explorer.And all progs.on the card are showing inactive generic icons.Any input.I did a hard reset AGAIN.so this would just be for further ref.I'm gettin up the balls to flash for the 1st. time with one of the roms from this site.
jcastex said:
Its impossible to change the name or delete the file!
Pls help me!
p4350 wm 6
Thanks and pls sorry for my english!acces deniend its the reason to no rename!
Click to expand...
Click to collapse
I've the same problem! can anyone help me? I tried Total Commander.
ruebyi
Related
I have a really annoying problem with my P4350.
Before the official Update i was running HERALD_WM6.0_4.12.07.06.PDAVIET with 4 MB Pagepool.
it worked really nice and i had never any problem with it.
Now i updated to the official HTC WM6 Rom. First i also installed the OS from PDAVIET over the Official one. But then i encountered after a little time the Bootloop of death.
it was always rebooting, and removing of the microsd did not really helped at the bootloop it was only stopping at the bootscreen and hang there forever.
the only chance was a Hardreset. After that i installed only the official Rom from HTC from the Bootloader. Now i am running only the official WM6 Rom and it is also rebooting after some time. i did not installed anything that i didnt installed also in the original WM5 Rom, and SD-Card removing also dont help.
After some Hardresets i installed a Safemode tool.
now i encountered another Bootloop and i can enter the Safemode. There i sometimes disable a Homeplugin, then it boot again. But not for long, it will hang again in the Bootloop. I have no idea wath File/Program is doing this thing and i have not many applications that boot at startup. It is also happening if i have no Home-Plugins enabled (from Safemode disabled).
can someone help me at this, or is it only possible that i downgrade or never install any application(wath is also no guarantee that it will not again enter the bootloop)
(sorry for every error in my text because i am German)
How long do you wait before giving up when you pull out the SD card? When I installed the home screen I got the continuous reboot and when I took out the sd card it stayed at the green windows mobile screen for about 2-3 minutes before booting into the home screen.
Also, have you tried this: http://www.modaco.com/Continuous-reboots-t256186.html ?
thanks for your help.
But i already waitet for way more than 3 minutes. i think it was ~ a half hour.
I already tried to rename the OMAP850_SDHC.dll but with no luck. The File is in the Rom and it is not alowed to rename this File. (if i look at the Settings from Resco Explorer ROM is activated)
my OMAP850_SDHC.dll is 46.38 kB big and from 02.07.07 5:44 if this information can help.
at the moment i try to avoid a reboot from my device...
I think i found the troublemaker.
I deleted a windows-design that i liked and used in all Rom-versions, and since i deleted the file it seems that the reboot-problem is solved.
If my Herald will hang again in a reboot-loop, i will write here again.
so long... thanks for the help.
DaveShaw Edit:
Split the thread from the NBH Extract thread.
Hi there!
First off all thanks for the great help and all the hard work you all doing!
Keep on going!
I have problem extracting my "RUU_signed.nbh" file using the the "NBHextract" tool. The "nbh" file I need is from the:
"RUU_Kaiser_HTC_WWE_1.56.405.5_radio_sign_22.45.88.07_1.27.12.11_Ship" Rom.
I'm trying to extract with the CMD, or trying to drag & drop the "RUU_signed.nbh" onto the "NBHextract", its says in the CMD: extracting. Bat in fact, noting happens! There only the same 2 file in the folder and nothing else.
Can any one help?
Maybe some of you can tray to extract the file and upload the result to www.rapidshare.com or somewhere else?
I'm using desktop with XP PRO English.
Please! I'm going crazy!
Shaico said:
Hi there!
First off all thanks for the great help and all the hard work you all doing!
Keep on going!
I have problem extracting my "RUU_signed.nbh" file using the the "NBHextract" tool. The "nbh" file I need is from the:
"RUU_Kaiser_HTC_WWE_1.56.405.5_radio_sign_22.45.88.07_1.27.12.11_Ship" Rom.
I'm trying to extract with the CMD, or trying to drag & drop the "RUU_signed.nbh" onto the "NBHextract", its says in the CMD: extracting. Bat in fact, noting happens! There only the same 2 file in the folder and nothing else.
Can any one help?
Maybe some of you can tray to extract the file and upload the result to www.rapidshare.com or somewhere else?
I'm using desktop with XP PRO English.
Please! I'm going crazy!
Click to expand...
Click to collapse
I'm lost sorry
Have you downloaded the exe and need the NBH File? If so Install WinRAR, right click the exe and click Extract...
If you have the NBH file, then I suggest you re-try the steps you quoted again. Let me know if there are any errors on any steps.
Ta
Dave
DaveShaw said:
I'm lost sorry
Have you downloaded the exe and need the NBH File? If so Install WinRAR, right click the exe and click Extract...
If you have the NBH file, then I suggest you re-try the steps you quoted again. Let me know if there are any errors on any steps.
Ta
Dave
Click to expand...
Click to collapse
Well, I did those steps before, bat have no result. Don't see any error at the CMD. only show me the extract progress and at the end (after 2 min), there are no result! Only the same 2 file I started the progress. (RUU_signed.nbh + NBHextract tool)
I have the NBH and need to extract it... So I can continue to step 6 at these guide: Reverting back to the AT&T or HTC ROM and SPL for Warranty or return http://forum.xda-developers.com/showthread.php?t=335568
Can any one trey to extract the RUU_signed.nbh from
RUU_Kaiser_HTC_WWE_1.56.405.5_radio_sign_22.45.88 .07_1.27.12.11_Ship" Rom for me and upload the result?
Thanks in advanced!
Ok, update! I try to extract this in vista by drag & drop, and it worked!!! Bizarre...; and I got 5 file from the extract. The CMD still didn't work in the vista though...
Bat now i'm confused, because I read on other thread that I need to do Hard SPL first so I don't brick my TyTn 2 device... and in the guide:
(http://forum.xda-developers.com/showthread.php?t=335568),
its says I don't need to do Hard SPL. So what should I do?
let me tell you the reason I want to flash the SPL: I install Hebrew support pack that I download from the net and it work ok till I start to notice a rapidly massage of low memory (I didn't install nothing else!), bat the most reason fact that I want to flesh the SPL is because in addition of that message, the cracked Hebrew pack, showing me the logo of the company that made the pack; every time I restart the device, just before the HTC welcome logo and its showing for at lest 30 sec!!! Every soft reset!! So I try to uninstal that pack and its still showing every restart! Even, try to up grade to WM6.1, and still its there!!!! So I start to read some thread and think I need that spl flash so I can get rid of that "sticky" logo that slow my device and steal my memory!!
Can any one now something like that issue, and what shold I do in order to uninstall that long logo?
Shaico said:
Well, I did those steps before, bat have no result. Don't see any error at the CMD. only show me the extract progress and at the end (after 2 min), there are no result! Only the same 2 file I started the progress. (RUU_signed.nbh + NBHextract tool)
I have the NBH and need to extract it... So I can continue to step 6 at these guide: Reverting back to the AT&T or HTC ROM and SPL for Warranty or return http://forum.xda-developers.com/showthread.php?t=335568
Can any one trey to extract the RUU_signed.nbh from
RUU_Kaiser_HTC_WWE_1.56.405.5_radio_sign_22.45.88 .07_1.27.12.11_Ship" Rom for me and upload the result?
Thanks in advanced!
Click to expand...
Click to collapse
Ok, update! I try to extract this in vista by drag & drop, and it worked!!! Bizarre...; and I got 5 file from the extract. The CMD still didn't work in the vista though...
Bat now i'm confused, because I read on other thread that I need to do Hard SPL first so I don't brick my TyTn 2 device... and in the guide:
(http://forum.xda-developers.com/showthread.php?t=335568),
its says I don't need to do Hard SPL. So what should I do?
let me tell you the reason I want to flash the SPL: I install Hebrew support pack that I download from the net and it work ok till I start to notice a rapidly massage of low memory (I didn't install nothing else!), bat the most reason fact that I want to flesh the SPL is because in addition of that message, the cracked Hebrew pack, showing me the logo of the company that made the pack; every time I restart the device, just before the HTC welcome logo and its showing for at lest 30 sec!!! Every soft reset!! So I try to uninstal that pack and its still showing every restart! Even, try to up grade to WM6.1, and still its there!!!! So I start to read some thread and think I need that spl flash so I can get rid of that "sticky" logo that slow my device and steal my memory!!
Can any one now something like that issue, and what shold I do in order to uninstall that long logo?
Shaico said:
Ok, update! I try to extract this in vista by drag & drop, and it worked!!! Bizarre...; and I got 5 file from the extract. The CMD still didn't work in the vista though...
Bat now i'm confused, because I read on other thread that I need to do Hard SPL first so I don't brick my TyTn 2 device... and in the guide:
(http://forum.xda-developers.com/showthread.php?t=335568),
its says I don't need to do Hard SPL. So what should I do?
let me tell you the reason I want to flash the SPL: I install Hebrew support pack that I download from the net and it work ok till I start to notice a rapidly massage of low memory (I didn't install nothing else!), bat the most reason fact that I want to flesh the SPL is because in addition of that message, the cracked Hebrew pack, showing me the logo of the company that made the pack; every time I restart the device, just before the HTC welcome logo and its showing for at lest 30 sec!!! Every soft reset!! So I try to uninstal that pack and its still showing every restart! Even, try to up grade to WM6.1, and still its there!!!! So I start to read some thread and think I need that spl flash so I can get rid of that "sticky" logo that slow my device and steal my memory!!
Can any one now something like that issue, and what shold I do in order to uninstall that long logo?
Click to expand...
Click to collapse
OK I see what your getting at... Some facts first...
1. The guide you posted a Link to advises how to restore the Stock SPL and ROM if you have Hard SPL and a custom ROM. It does not mention Hard SPL for the simple fact that it is a guide on how to remove it (assumes you have it otherwise you wouldn't be reading the guide).
2. The SPL is the bootloader similar (in ways) to your PC's BIOS. I am pretty certain it has not been comprimised.
Firstly we need to know which splash was changed. There are 3 possible splashes that could have been changed. Have a look at this guide by -888- on upgrading you splash.
It is most likley to be one (or both) of the last two. Changing the first one requires Hard SPL and Flashing.
Rather than fixing the splash screens, I'd do a Hard Reset that will remove everything that was not part of your original OS ROM image.
If it is still there after that, I'd flash HardSPL and then flash a new Splash screen.
And, finally , this forum does not support cracked software, I will help you remove it however, if you promise to pay for it in the future
Ta
Dave
DaveShaw said:
OK I see what your getting at... Some facts first...
1. The guide you posted a Link to advises how to restore the Stock SPL and ROM if you have Hard SPL and a custom ROM. It does not mention Hard SPL for the simple fact that it is a guide on how to remove it (assumes you have it otherwise you wouldn't be reading the guide).
2. The SPL is the bootloader similar (in ways) to your PC's BIOS. I am pretty certain it has not been comprimised.
Firstly we need to know which splash was changed. There are 3 possible splashes that could have been changed. Have a look at this guide by -888- on upgrading you splash.
It is most likley to be one (or both) of the last two. Changing the first one requires Hard SPL and Flashing.
Rather than fixing the splash screens, I'd do a Hard Reset that will remove everything that was not part of your original OS ROM image.
If it is still there after that, I'd flash HardSPL and then flash a new Splash screen.
And, finally , this forum does not support cracked software, I will help you remove it however, if you promise to pay for it in the future
Ta
Dave
Click to expand...
Click to collapse
First off all, thanks for the help. I appreciate it!
I must mention that I buy the original version in advanced. I just was curious to check the net version and it turns out that it's not so good... to such an extent that I ruin me Kaiser...
now let me be more specific with me problem because i m not sure I explain the problem clearly and I don't want to start a progress that I don't know how to do....
So, like I say, after I finish the install of the language pack, I had to clear storage in order to crack the license. But since that, every restart, appear the logo of the software company for 30 sec!!! Every restart!!!! Its make me crazy!!!! (The logo appear just before the HTC logo load. (It's appear with the rom and the radio version = R.G.D). But this is not the main problem!! The most important problem is that since the install, its keep say me that I'm run out of memory, and I m even didn't install nothing!!! This is bad!
So off Corse I'm try to do hard reset and even try to upgrade to WM6.1, but the cursed logo is still there!!!!
Now, after I try to explain the problem, I want to know if the solution you recommended may solve the logo problem and more important the memory "leak"....
What I basically want is to bring me Kaiser to its original status like from "out of the box"... because it's only 2 week old!!!!!
I'm hope you understand me problem.
Thanks you in advanced!
Shaico said:
First off all, thanks for the help. I appreciate it!
I must mention that I buy the original version in advanced. I just was curious to check the net version and it turns out that it's not so good... to such an extent that I ruin me Kaiser...
now let me be more specific with me problem because i m not sure I explain the problem clearly and I don't want to start a progress that I don't know how to do....
So, like I say, after I finish the install of the language pack, I had to clear storage in order to crack the license. But since that, every restart, appear the logo of the software company for 30 sec!!! Every restart!!!! Its make me crazy!!!! (The logo appear just before the HTC logo load. (It's appear with the rom and the radio version = R.G.D). But this is not the main problem!! The most important problem is that since the install, its keep say me that I'm run out of memory, and I m even didn't install nothing!!! This is bad!
So off Corse I'm try to do hard reset and even try to upgrade to WM6.1, but the cursed logo is still there!!!!
Now, after I try to explain the problem, I want to know if the solution you recommended may solve the logo problem and more important the memory "leak"....
What I basically want is to bring me Kaiser to its original status like from "out of the box"... because it's only 2 week old!!!!!
I'm hope you understand me problem.
Thanks you in advanced!
Click to expand...
Click to collapse
Do you have a storage card? I wonder if it flashed off the storage card? Anyhow, let's get busy...
Firstly remove anything you want to keep off the card and then format it.
Then flash the Hard SPL using the instructions here: http://forum.xda-developers.com/showthread.php?t=396922 (Second set of instructions in post #2).
Once, you have completed the flash, enter the bootloader before Windows Mobile loads.
Then, when you are in the bootloader flash a New ROM and Radio.
Hopefully that will remove everything that shouldn't be there.
Also, moving out of pof's thread. To a new one
Ta
Dave
DaveShaw said:
Do you have a storage card? I wonder if it flashed off the storage card? Anyhow, let's get busy...
Firstly remove anything you want to keep off the card and then format it.
Then flash the Hard SPL using the instructions here: http://forum.xda-developers.com/showthread.php?t=396922 (Second set of instructions in post #2).
Once, you have completed the flash, enter the bootloader before Windows Mobile loads.
Then, when you are in the bootloader flash a New ROM and Radio.
Hopefully that will remove everything that shouldn't be there.
Also, moving out of pof's thread. To a new one
Ta
Dave
Click to expand...
Click to collapse
I'm sorry, it didn't help! Or I didn't understand the mining of the post! so I follow the instructions and then what? Nothing change! It's all the same! I can't see any different! What else can I do? How can I erase all the data include all!! Data!! And start again and make it brand new again? Im just want this logo to go away!! How do I make my Kaiser new again with no foreign files that no came with me device from the factory! I want to Cray!! I can't help it any more! Please help.
Can you please help me live? Can we kindly chat in the messenger? I'm lost of me mind with all this posts and cant mange this alone!
Thank you in advanced!
Anyone can please help?
Hi, sorry for the delay.
The instructions in my last post should get you back up and running. You'll have have to read up on the wiki and the ROM Development stickies for more help.
I am at work now, and am pressed for time at the moment, have a look on #xda-devs chanel on FreeNode after 8-9PM (GMT) for me. I'll be able to chat then. (I am also on MSN, but I don't use it at home that often. I'll try and make an effort over the next few days.)
Ta
Dave
So people around here sometimes get troubled with regular flashing that doesn't work anymore.
I'll explain my problem on this part:
I flashed to a new ROM just to find out that i didn't like the content so i wanted to flash back to TOUCH X.
I did the usual stuff to flash my phone with, Hardspl, then bootloader etc. etc.
PROBLEM!
Now all my phone seems to be doing is go into bootlader and start updating. However, after 3 seconds i get the message that the update is complete. My phone resets itself, and i found out that nothing has changed. I tried it a number of other times, without results.
Now my question is: is there any other way to do this, this is obviously not working!
post all your ideas here so other people can read this in case that they have the same problem!
Everytime you flash a ROM, you do not need to hardspl your device, only once...I would reformat your memory card,use a stock original rom and see if it will flash with that....usually the issue you are seeing is because the nbh file is not being read properly, make sure your nbh file is named correctly.I have had the issue earlier in my days where if I copied the nbh file through active sync something gets screwed in the transfer...used an external card reader and copied it to my memory card after formatting it and it went through....just some suggestions....Good Luck
Regards,
WC
didn't solve it at all.
More suggestions?
SyntheticDistortion said:
didn't solve it at all.
More suggestions?
Click to expand...
Click to collapse
seems to be your problem? ---> CLICK
Nope, didn't do anything..
Any other suggestions?
EDIT: Really a lot of thanks for anyone helping, i really would love to start flashing again!
grateful for the help arnt you..
try flashing the USB method, if it works its probably due to your memory card. (unless ur already using the usb method, then try the memory card method!)
How do i use the USB method exactly?
And really guys, thanks for all the feedback, maybe make this a sticky for future reference?
SyntheticDistortion said:
How do i use the USB method exactly?
And really guys, thanks for all the feedback, maybe make this a sticky for future reference?
Click to expand...
Click to collapse
well what you do is download the file attached to this post (it is available in one of the stickies but when i tried to download it, it failed so i zipped this one up for you)
extract the .exe within to where your nbh file is (not on xperia, on computer)
make sure there is no KOVSIMG.nbh on your memory card!
put your phone in bootloader (tricolour screen) and plug in via USB
run the custom_RUU.exe and follow the prompts pressing next etc.
you don't have to sync via activesync 1st like it says.
ignore the version number of the ROM just make sure your using the correct nbh and flash!
urm i think you should at least try to look at the stickies .........
this is very useful. i had problem flashing using micro sd so all my flashes are via usb.
http://forum.xda-developers.com/showthread.php?t=497511
That seemed to have done the trick people!
Thanks very much and keep up the good work!
Hello. Yesterday morning when i woke up suddenly my touch screen did not respond any more. I try reinstalling windows or hard reset but now i can not even get over tap the screen.Please help me. You already helped me once when i was going to throw it away because i thought it's a hardware problem and it was a software one.I did the soft reset and leave it for a day then it worked but when i wanted to charge, it happened again and i have the same problem now.Any way a thing it's certain it is a software problem.If you have other advice please help.
another problem
I tried installing lots of roms hoping it will be fine. but now i installed a 6.1 version of wm and when i try installing wm 6.5 it stopes in loading screen and the pc gives me an error conection.What about this?
Moved as not ROM Development.
Place a welcome.not file on root of storage card can be a .txt file but change the extension doesn't want to be welcome.not.txt this will get you past all the configs on setup.
Please be more specific
Where can i find a welcome.not file?
linucu said:
Where can i find a welcome.not file?
Click to expand...
Click to collapse
You make it out of a .txt file
Have done it 4 u.
Thank you but that was not the problem
I did as you said and it worked but that was not the problem.The problem is my touch screen not responding.And it's not a hardware problem because if i did as i have been told to fully charge the phone, then do a soft reset and leave it for a day it was as new.But when i try to charge it again i got the same not responding screen. Now after all this i have another issue and that is when i try doing a soft reset the phone resets and it sopped on gray screen with Loading... and the pc gives me error connection. So i get this only i put a 6.1wm. Is this the reason for not letting me change the wm to 6.5 one? i will go crazy with these strange things that are science but have no explanation. Where is the science then? What you did was to allow me to use the phone without touch screen. Well...thank you, but i know there is a way to get the phone normal again and that is what i need you to help me with. Thank you. Catalin
Are you Hard-SPL'd?
Regards problem if software then flashing a different ROM even stock should be able to tell you, i know you think not hardware but if repetitive then maybe you just fluked the being ok again.
Anyway flash another stock ROM, then if fine flash a 6.5, you don't have to use computer as can flash via SD.
First of all thank you
Thank you because you try to help but please talk so i can understand. What is stock rom?
"even stock should be able to tell you" what is stock?
And now i have another one. It can not connect to active sync.
tell me please how can i Flash form SD?
I can not insatll anything from pc
So i don't understand why it does not allow me to do anything like hard spl, or flash rom, or anything to install from pc. It connects to active sync and lets me access the card but when i try installing something it stops.
Ok first off I am really sorry for the stupidity and should have paid more attention. I was flashing the NBH on my Tilt 8925 and I got the wrong one! it was the KAISIMG-PANEL1-428.NBH that I downloaded and now the text is hard to read and it wont install and I cant change it. Right after I did that I found the forum that told you witch one to use. I wanted to cry!!! So what I'm asking is my phone done for? or is there a way to fix this? like through the andboot folder somehow?
Thank you for any help at all!!!
you learn from your mistakes though, I'm sure I wont do that again
Fixed it! :d
After I gave up I remembered someone said to hold the camera and the power button and reset buttons. I did that just to see what it would do and the colored screen came up with usb at the bottom. so I triad the right file and ran it again and it worked! Now I'll have to give it another go!
so this can be deleted now Thanks!
Just for future reference.
If you flash the wrong nbh with android, you should be able to flash the correct one using either the SD method, or the USB method.
Above all, do not panic, panic bricks more devices than bad flashes ever did
Since this is the Android area, I must say we are extremely lucky, since we are able to flash a new nbh without losing anything at all as far as the OS is concerned, your data and system files will remain intact, flashing an android nbh only replaces the zImage and the android bootloader files, unlike WM where you flash the whole OS and lose everything
Android
That's good to know because I thought I lost the phone for good. I didn't have any data on it that I needed, I was trying to install android to nand and just got the wrong NBH.
The only thing now that would keep me with WM 6.5 is cant get the wifi to work right. It connects to the router but the internet cuts out very bad, like it will work for 10 seconds then cant get it to work at all for 20min then it will load a web page then doesn't work again!
I did the same thing to my Tilt. I downloaded the Kaiser for Super Eclair and flashed it and did not not know I did not flashed the HardSPL.nbh.
I finally figured it out and flashed the HardSPL.nbh. It is at 3.29 right now. But I the phone keep getting error after the penguin screen with scrolling text. It said something about unable to read data. How do I fix this problem?
BeenAndroidized said:
I did the same thing to my Tilt. I downloaded the Kaiser for Super Eclair and flashed it and did not not know I did not flashed the HardSPL.nbh.
I finally figured it out and flashed the HardSPL.nbh. It is at 3.29 right now. But I the phone keep getting error after the penguin screen with scrolling text. It said something about unable to read data. How do I fix this problem?
Click to expand...
Click to collapse
Jesus... the last post is more the 1year old.
I know you must search, but if the last post is that old, the probability that everything in it is outdated, is near 100%.
Well, that is the what I found. I hate digging up old post especially when it's that old.