i installed the 3 cabs in the zip folder on my HTC mogul and ran them after hard reseting and tried to run hard spl but after that but every time i run the enter bootloader for hard spl when it starts workin it disconects from the USB before it gets to one percent and yes i am signed on as a guest on active sync.
allk said:
i installed the 3 cabs in the zip folder on my HTC mogul and ran them after hard reseting and tried to run hard spl but after that but every time i run the enter bootloader for hard spl when it starts workin it disconects from the USB before it gets to one percent and yes i am signed on as a guest on active sync.
Click to expand...
Click to collapse
The mogul is NOT, I repeat, NOT a herald device! If you like your phone, do NOT flash it with that HardSPL.
Related
I cannot get activesync4.5 to link up to wizard after loading button rom. IPL is 1xx and spl is 2xx. I am not sure what to do next with this since I cannot cid unlock without getting a connection with as. I have not found any definitive answers anywhere, and I have been reading alot, and then I read alot more. I have cleared the temp folders I have ran chkdsk I have manually started as on ppc. I really could use some help on what my next steps should be to get a link up from the ppc to the pc.
you're phone didn't flash correctly. put the phone in bootloader mode (hold the comm manager, the voice dial button, and hit the small hole on the side at the same time...should bring you to the tri-color bootloader mode) and reflash butons 1.05. you need to keep reflashing until BOTH your IPL and SPL are 1.05. having different numbers is not a good thing.
monkey_knight said:
you're phone didn't flash correctly. put the phone in bootloader mode (hold the comm manager, the voice dial button, and hit the small hole on the side at the same time...should bring you to the tri-color bootloader mode) and reflash butons 1.05. you need to keep reflashing until BOTH your IPL and SPL are 1.05. having different numbers is not a good thing.
Click to expand...
Click to collapse
This is an 8125 and I have been able to get to the bootloader screen by pressing the camera button and power together. I have an IPL of 1.01 and an SPL of 2.25. I have flashed the phone 3 times now and there has been no changes as to the SPL as of yet. I will go for another round on it. Has anyone else encountered this problem with G3 8125 Wizard??? I have seen similar problems while reading through the forums, although no solutions.
When you press the comm manager voice dial button and press the small hole on the side that is for a hard reset right? Anyways I have reloaded the button 1.05 rom and it still has 2.25 SPL any ideas????
amsatnetg said:
Anyways I have reloaded the button 1.05 rom and it still has 2.25 SPL any ideas????
Click to expand...
Click to collapse
yes. flash the original 2.25 you had before or the wizard love 2.26 (assuming your phone is already CID unlocked)
mestrini said:
yes. flash the original 2.25 you had before or the wizard love 2.26 (assuming your phone is already CID unlocked)
Click to expand...
Click to collapse
how can it be cid unlocked if I have not succesfully gotten the phone to connect with activesync4.5 to be able to load the enablerapi file and run the lokiwiz.02b bat file??? This lack of connection to the AS is where I am stuck. From the read first sticky I should be loading the enablerapi file on and running the lokiwiz.bat file. I am not making a connection between the phone and the computer to be able to do that, at this time. I have now loaded the button rom on the phone 5 times and still no change in the SPL. What am I missing here????
One other thing that I noticed is that when I plug the USB into the Wizard it immediately trys and succesfully sets up a local area connection. It is currently set up as local area connection 5. This connection says that it is a windows mobile based device connection. What do you all make of this one??
currently these are my boot readings
IPL 1.01
SPL 2.25
GSM 01.12.10
OS 1.5.4.2
Cingular/ATT Customer
8125 HTC Wizard
MODEL 100
UPDATE!!!!! So the answer to my own thread for anyone that will run into this problem, for myself, was to load the button rom then remove activesync program from xp, then without reboot redownload activesync with the phone connected to usb, if it still does not come up reinstall button rom without reboot. Also disable ALL firewall and antivirus programs. This should get the activesync to see your device, and then it will try to connect. Just cancel the attempted sync connection and you will be on active sync as a guest. I hope this will help out some newbies.
I am experiencing the exact same issue. Any ideas??
Uninstall ActiveSync 4.5 and install an older version.
AS4.5 seems to have problems with some WM5 devices.
starkwong said:
Uninstall ActiveSync 4.5 and install an older version.
AS4.5 seems to have problems with some WM5 devices.
Click to expand...
Click to collapse
I tried 4.5, 4.2, and 3.8 all without luck. Any other ideas?
Tried on another XP machine and it worked using ActiveSync 4.2.Now if I can get activesync to connect to WM6 ...
Finally someone mentions the OS on the PC. That will help alot you know. well hope all is sorted out! Good luck
Well i've tried several different versions of activesync (3.8, 4.2, and 4.5 which is needed for WM6) uninstalling rebooting, connecting the device several times, rebooting both the laptop and the phone, and nothing seems to work on my newer Core 2 Duo laptop. It simply will not connect to the phone. It worked perfect _before_ the downgrade to the Button ROM though using activesync 4.2 and 4.5 to the Cingular ROM.
All works perfect on my older P4 laptop though, both run Windows XP SP2 btw. Button ROM connected first try. I'm thinking something may be wrong with the OS on my new laptop, so I may have to blow it out and start all over since it's the one I need to sync with...
At least I got the XDA WM6 r2a Rom, IPL/SPL 3.08, and Faria 2.69.11 installed and working without a hitch on the 8125 so its fully usable now. Now to keep plugging away till I can sync it on my main laptop.
Frustrating!
where can I find active sync 4.2? I'm stuck just like he is.
I got IPL 1.01 and SPL 3.08
i'm in bootscreen right now trying to reflash it, but nogo.. I can't get a connection with activesync, so the romloader program is not getting a good connection
razorseal said:
where can I find active sync 4.2? I'm stuck just like he is.
I got IPL 1.01 and SPL 3.08
i'm in bootscreen right now trying to reflash it, but nogo.. I can't get a connection with activesync, so the romloader program is not getting a good connection
Click to expand...
Click to collapse
Look here:
http://www.microsoft.com/downloads/...3a-28bf-4cac-a682-58d3233efb4c&displaylang=en
So i just attempted to flash my tilt.
These are the steps i did.
Used Jump SPL 1.56 Kais
Then flashed a Kaiser Custom RUU.exe
everything was good at this point.
I then attempted the Kaiser SUperCID tool
when i did the unlock radio is when the problem occurred. After initializing and completing the screen turned black and does not display anything after the 3g sreen. I have done several soft resets and am attempting to do a hard reset with the soft keys but all it does is restart the phone....
i am not able to do a hard reset via sys>clear storage since no screen is displayed
this is what my phone does show
the tri color screen is this
kais1*0
spl-3.28.Hard
cpld-8
and it says security unlocked above all of that.
The ATnT screen shows this
R 1.70.Olinex
G 25.65.30.04h
D 1.62.00.00
please help
You need to follow step 0. Too late know. Which includes having an actual "RADIO" ready.
1.70OliNex is not a Radio. Thusly the Device can't load the Phone. Find a Radio and Flash it
Oh And Count this as your Freebie. Next time Search for your answer. And if you don't find the answer this should have been posted in the SuperCID thread.
Thank you kind sir. Off to look for a radio
Ghxoxst said:
Thank you kind sir. Off to look for a radio
Click to expand...
Click to collapse
Before you go off.
Here's something to try. The SIM/CID Unlocker do not work with the stock rom and you should have put hardspl on there.
Setup activesync and make sure that it detects your phone. As long as activesync works, you should be able to flash the stock rom and radio on the phone (even if the display is blank).
1st use jumpspl
then put on hardspl (read and follow the hardspl instructions)
then upgrade to 6.1 ROM
Then Unlock
then reflash with the rom of your choice with the matching radio
you should be good to go.
well i finally figured out the hard reset, which i did. It booted up and i was able to do the screen alignment etc, but once i was on my actual home screen it CUSTOMIZED and loaded a bunch of who knows what and back to the blank screen...
well i do have hard spl 3.28. I will try again....Im also not sure if my phone is 6.0 or 6.1
Ghxoxst said:
well i finally figured out the hard reset, which i did. It booted up and i was able to do the screen alignment etc, but once i was on my actual home screen it CUSTOMIZED and loaded a bunch of who knows what and back to the blank screen...
well i do have hard spl 3.28. I will try again....Im also not sure if my phone is 6.0 or 6.1
Click to expand...
Click to collapse
If you have hardspl on there, then just flash one of the cooked roms on the phone. I loaded the L26 Rom and it works great. It will include a radio firmware and is compatible with the SIM/CID unlocker.
the question i have is how do you flash without being able to execute the program from the phone? How am i able to execute it from the active sync?
Ghxoxst said:
the question i have is how do you flash without being able to execute the program from the phone? How am i able to execute it from the active sync?
Click to expand...
Click to collapse
Have you connected it to the computer via usb? Does activesync see the phone? You won't see anything on the phone itself until you correct the problem. As long as the computer activesync sees the phone you should be able to flash it from the computer.
I had the same issue
Just follow the steps
get the SIM unlock code from the computer
then flash a "real radio"
Once it finishes and boots up
it will ask you for the sim unlock code
AND VIOLA!!!
got it going
flashed it from my mini sd card after fat32 formatting it.
works like a charm
Thanks to everyone
A while ago I tried to Flash a version of WM6 from mfrazzz on my wizard. The installation seemed to go ok, but when I boot it up i coudn't get past the second splash screen. I thought the phone was a gonner until last night, when I gave it another shot putting on Button ROM. I followed these instructions and it worked. The instructions also had me unlock the phone, and that worked fine too. after that I tried updating my IPL and SPL, Right now my IPL is 1.05 and SPL is 3.08
After this I tried unsuccessfully to get WM6, I think I started off trying Faria.
(So here is the actual problem)
After I tried installing Faria unsuccessfully, I couldn't get Button ROM back up. I'm stuck on the second splash screen (picture of a mug of beer in front of the Colosseum). I've tried flashing my phone w/ everything i've got, including button ROM and Love, and nothing works. most of the WM6 Update Utilities won't even connect. Button Rom connects, stalls at 98%, finished and says it was a success, but I'm still hung up on the Splash.
(I'm running WinXP w/ SP2)
I really just want something running on this phone, don't care what it is.
Thank you for your time
Download official stock rom to recover back and download WST_4.2.2 to verify the CID lock/unlock status,most probably its still CID locked.or you can even reflash 'Button's Rom' again.
No, I've tried to reflash button rom many times. It says it works but it gets hung up on the splash. Since I can't get anything to run on it WST won't work (I think)
Yes! WST only works on a working OS,have you tried to flash the official stock rom ?
Don't activesync or establish partnership,better if you altogether disable & close activesync and end process 'WCESCOMM.EXE' in the Task Manager and try to end as many applications running at the background.Don't surf the net,disable all anti virus and firewall.
Simply get the phone into Bootloaders mode,hook up with pc via usb cable,watch small usb appear at the bottom of Bootloader screen and run the Rom,hope it'll work.
hEY ZABARDAST
zabardast_1 said:
Yes! WST only works on a working OS,have you tried to flash the official stock rom ?
Don't activesync or establish partnership,better if you altogether disable & close activesync and end process 'WCESCOMM.EXE' in the Task Manager and try to end as many applications running at the background.Don't surf the net,disable all anti virus and firewall.
Simply get the phone into Bootloaders mode,hook up with pc via usb cable,watch small usb appear at the bottom of Bootloader screen and run the Rom,hope it'll work.
Click to expand...
Click to collapse
I did this when my Wizard stucks on the splash...
Get mtty 1.04 i thin i dont remember exactly but the higher i ever saw.
kill process wcesscom in PC
conect the ppc on Bootloader
click on conection it shows USB if not... start up again the process
then a white screen appears
I type: task 28
then it works a little on some memory directions
I type: task 28 55aa [or something] (its better get the info on wiki cause it works on chip directly)
without unplug the PDA starts the RUU again...
It works for me...
This is a process for HTC Universal but it works on Blue angel and Wizard for sure!
wait a little i will confirm the steps and the exactly words to type in.
you might need clean the ROM or your flash ROM is overcooked.
I can repair your phone !
+ Que PPC said:
I did this when my Wizard stucks on the splash...
...
wait a little i will confirm the steps and the exactly words to type in.
Click to expand...
Click to collapse
Hey + Que PPC!
Have you confiirmed those values? And is your Wizard CID unlocked?
This would be great to confirm working so that all those with CID locked devices could get their phones back - without paying IMEI-check.co.suckourmoney.uk
@ twig2256
If your phone is CID unlocked try Drugstore's method of recovering Splash Screen frozen phones
cheers
YES
The values are the same for every DOC CHIP
When the MTTY conects to USB type exactly this...
task 28
(then it will work formating and cleaning the DOC
then it says succesfully clean
and now type...
task 28 55aa
it again works on the same process you can close the mtty without unplug your device... update your device with a Stock rom.
Actualy I have issues with mtty i dont know why i can acces to USB it say CMD GOD Damn can anybody helps...
This is the link that mestrini said for drug gsm store metod to unfreeze
http://forum.xda-developers.com/showthread.php?t=276963
Hey mestrini see this...
http://wiki.xda-developers.com/index.php?pagename=Uni_Stuck_Bootloader
even if it is universal it work for Wizard i did it once it works for me. but now it wont why????
zabardast_1 said:
Yes! WST only works on a working OS,have you tried to flash the official stock rom ?
Don't activesync or establish partnership,better if you altogether disable & close activesync and end process 'WCESCOMM.EXE' in the Task Manager and try to end as many applications running at the background.Don't surf the net,disable all anti virus and firewall.
Simply get the phone into Bootloaders mode,hook up with pc via usb cable,watch small usb appear at the bottom of Bootloader screen and run the Rom,hope it'll work.
Click to expand...
Click to collapse
can't solve my t-mobile mda
I dont' know if this is the problem of onkolog rom or just the way i flash my phone.
First i use the old rom of davideuck Davideuck_V-7, CE OS 5.2.20769 on 29,March . I then got trouble with battery drained with this rom when i used SPB 3.0.
I try to update to new 6.1 rom of onkolog on 1, May
This is what i did.
My phone was on and connected to my PC. I then run HardSPL 1.56 successfully.
The phone was on again and i run the wrapper file in the same folder with onkolog rom. It run smoothly but when it recognized my O2 network it told me to be restarted after 5 seconds and when the "htc" words appear my phone hang.
i need to do a soft reset and this time it worked.
I then tried to install flip it. It required to restart after install and this time i got hang again.
I install htc Tweak and use it soft reset, some times it worked sometimes my phone hang and i need to do soft reset.
The same problem appear when i used A-A reset software.
I then decided to go back to early version of onkolog 6.1 rom (used older version of hspl) on 1-April and still got the same problem.
I tried to reflash with uspl but still stucked with usb driver.
Can anybody tell me how to show this problem . I really like the idea of onkolog but maybe he is too busy to answer me.
I have successfuly flashed my X1 and im installing costum rom on them.
But now friend came with his X1 wanting me to install custom ROM on it.
I started Hard SPL unlocker and everything gone OK until it came to bootloader mode. Windows installed all drivers without problems but progress bars on both phone and pc were at 0%. After about half minute waiting at 0% it thrown out error 626. After that i taken battery out and back in and phone boots normally with Stock SPL.
A am suspecting that problem is in Stock SPL version. I have 0.72 while in Hard SPL thread it says 0.52 and maybe Hard SPL is not supported on this version.
I have searched about 626 but didnt find any solution.
Please help.
go to olinex hard spl section and write about your problem maby they can help u
Onlinex hard spl section?
I must be blind. Where is that?
matejdro said:
Onlinex hard spl section?
I must be blind. Where is that?
Click to expand...
Click to collapse
http://forum.xda-developers.com/showthread.php?t=431218
go here
matejdro said:
I have successfuly flashed my X1 and im installing costum rom on them.
But now friend came with his X1 wanting me to install custom ROM on it.
I started Hard SPL unlocker and everything gone OK until it came to bootloader mode. Windows installed all drivers without problems but progress bars on both phone and pc were at 0%. After about half minute waiting at 0% it thrown out error 626. After that i taken battery out and back in and phone boots normally with Stock SPL.
A am suspecting that problem is in Stock SPL version. I have 0.72 while in Hard SPL thread it says 0.52 and maybe Hard SPL is not supported on this version.
I have searched about 626 but didnt find any solution.
Please help.
Click to expand...
Click to collapse
Just got that error yesterday while updating my Rom and OS go to Settings, Connections, USBto PC, then choose active sync and check enable advance network. You might need to reboot your host pc to recognize changes on you mobile device.
Tried both checked and unchecked and dont work
I have managed to solve it!
Problem was newer Stock SPL.
What i did is installed image that contained old 0.52 SPL and now i can finally install Custom ROMS
Great!!! I will remember that one too.