Remove O2 boot up screen - Tilt, TyTN II, MDA Vario III General

Hey guys, not sure if ya can help, or if this has been asked before
I recently got an O2 xda stellar(kaiser)
i used to have a trion
Now I had installed the Hard SPL, then unlocked the CID , so boot screen now says at the top "security unlocked", and I have put a Schaps 4.30 FULL ROM ON, and it all works graet.
However the phone still boots up first displaying the O2 splash screen , then a HTC splash screen before the windows mobile splash screen
Does anyone know how to get rid of the O2 boot screen?
Thanks

if you had put in some effort to find the answer yourself, you would have seen "Flashing Custom Splash Screens" in the wiki and obtained this link
http://forum.xda-developers.com/showthread.php?t=334907

Related

how do I remove at&t splash screen from Tilt

I have searched and can't find an answer, I have a at&t tilt I have flashed it with Hard-spl and Duttys latest rom, but I still get the at&t splash screen when it first boots up. is there any way to remove this or am I stuck with it.
most of the treads on boot screens only let you change the 2nd and 3rd boot screens not the first one.

kaiser stuck on tri screen is it a brick???

i hope this is where i should post this.
whilst using my phone it froze,so soft reset was done then it went into tri screen
my kaiser wont go out of tri screen.i have this on screen.
kais130 mfg
spl-1.0.olipof
cpld-8
after trying hard reset and soft reset it wont pass this screen,it loads straight back to bootloader mode.i had duttys 6.1 rom on and nikis radio.
is there a solution to this problem.all was fine until this.ive searched all over for the past week and i cant seem to find a solution,so a little help is called for.id appreciate any help if possable and thank you in advance
Are you sure that your camera-button isn't stuck? Try pushing it hard few times, and then boot again.
Try flashing an official rom onto it while on that screen?
hi tried new rom and camera button isnt stuck,it seems like theres something wrong with spl-1.0.olipof.after installing new rom it boots straight to tri screen.can olipro be tacken off.just thinking of other things to revert to normal.when soft reset done it goes straight to tri screen
Try HardSPL
Why not flash it with a different SPL - like any of the HardSPLs such as Jocks:
http://forum.xda-developers.com/showthread.php?t=396922
and then flash with a new rom, suitable to that SPL?
rgds, MN
Fyi, this issue is being discussed in lots of threads @ ROM Development... I do have the same problem.
http://forum.xda-developers.com/showthread.php?t=402562
http://forum.xda-developers.com/showthread.php?t=371154&page=9
... and this one being the most recently updated:
http://forum.xda-developers.com/showthread.php?t=393337&page=29
Just to point out that the problem is solved (I think) - read here -> http://forum.xda-developers.com/showthread.php?p=2415437#post2415437

help to unlock my tytn2 in uk orange network,

HI , friends i been trying to sim unlock my new tytn2 which is in uk orange network now.
I tried to install hard spl, i m new to this technical worlds like cooked rom, new hard spl etc ,.any one please tell me how to do this step by step,
When i tried to install hard spl, there comes a tricolor screen first white screen with progress bar 0% , and after some time it stucks and in pc shows error message. tried with jump spl method described by some one, in the kaiser section, what is the meaning of wm6 and wm6.1
Following are the details of my phone
R 1.27.12.29
G 22.45.88.07H
D 1.81.00.00
KAIS130
SPL-1.81.0000
CPLD-8
What should i do to get my phone unlocked, plz help i assure 5 pounds to the one who has time to help me in this. cheers friends.
WM6 and WM6.1 are Versions of Windows Mobile, see Settings, About on your phone.
Looking at the Radio version, you are a WM6.0 user still.
To install Hard SPL read here: http://forum.xda-developers.com/showthread.php?t=334679
If you get a white screen, read here: http://forum.xda-developers.com/showthread.php?t=354061
Once you have Hard SPL complete, you can SIM Unlock, read here: http://forum.xda-developers.com/newreply.php?do=newreply&noquote=1&p=2572785
I suggest you read here Getting Started and on the XDA Wiki, there is lots of information on the HTC Kaiser page that covers the basics.
It is appreciated to search and read before posting new threads when the information is already available. If you get stuck with one part, re-read the thread, search for your problem, and then (and only then) post in the thread you are trying to follow.
Thanks
Dave
thanks dave.but i tried it, i couldnt even install hard spl, i dont know what happens when i run jumpspl also it shows white screen no further actions takes place. i dont know what to do now.
pappoos4u said:
thanks dave.but i tried it, i couldnt even install hard spl, i dont know what happens when i run jumpspl also it shows white screen no further actions takes place. i dont know what to do now.
Click to expand...
Click to collapse
Try SSPL First, then JumpSPL 1.56, then JumpSPL 1.93. one should work.
Ta
Dave
pappoos4u said:
...i dont know what happens when i run jumpspl also it shows white screen no further actions takes place...
Click to expand...
Click to collapse
Dave's second link above says "If you get a white screen..."

Remove splash screen "Test only not for sale"

Anyone can provide specific instructions how to remove the "for test only not for sale" message when booting my Jade (htc 3g) device?
Already flashed the ROM but that screen refuses to go... I also tried using the splash tool - created nb for the new splash screen but I can't find the tool to create the nbh for Jade...
Thanks
"test only not for sale"
I have a Touch HD (Blackstone) which I flashed back to a HTC ROM. This cleared the Test Only Not For Sale

Idea Cellular Splash screen

Hi,
I have a retail Opal (not network locked). But during start-up, i get an Idea Cellular (an Indian cellular operator) splash screen right after the Smart Mobility splash screen. Is there a way to get rid of this screen? Probably replace it with something else.
I did search the entire forum and came across a few posts about splash screens. Most seem to suggest that the phone has to be flashed with another ROM. I'm quite new to the WM world. I was wondering if it is possible to change this splash screen?
try Splash Changer by xiaojin1985.
http://forum.xda-developers.com/showthread.php?t=517483
Well u can always install a new ROM. This removed the splash from my phone.
and if u re install the stock then youll get the HTC splash.
btw is it possible to change the FIRST splash logo? i mean the one where your spl version and so on is listed.
Install Advanced config 3.2
You can so easily do this by installing Advanced configuration v3.2 alongwith .NET compact framework 3.5.... All the best....
logicfox said:
Hi,
I have a retail Opal (not network locked). But during start-up, i get an Idea Cellular (an Indian cellular operator) splash screen right after the Smart Mobility splash screen. Is there a way to get rid of this screen? Probably replace it with something else.
I did search the entire forum and came across a few posts about splash screens. Most seem to suggest that the phone has to be flashed with another ROM. I'm quite new to the WM world. I was wondering if it is possible to change this splash screen?
Click to expand...
Click to collapse
The startup is using /windows/Idealogoopalgif.gif file. Copy the file you want to use for the startup to windows directory & do following in the registry
Go to HKLM/Software/HTC/HTCAnimation & change the StartupGif file to the one you want.
PS: only gif files allowed

Categories

Resources