I bought this phone already tweaked with Dutty's Rom etc. Is there a way to check to see if it has been SPL'd? Files?? Etc.
You need to put the Kaiser in Bootloader mode and it should say Olipof at the top left (or right, can't remember exactly)
*EDIT* What Cosmic Blue below says
bigboyhf said:
I bought this phone already tweaked with Dutty's Rom etc. Is there a way to check to see if it has been SPL'd? Files?? Etc.
Click to expand...
Click to collapse
if it is already tweaked with Dutty's Rom. It will have hard SPL on it but in bootloader mode it should say olipro Hardspl in the upper right hand corner.
Ok, I read how to get into bootloader mode. Once there, is there anything special I should know about gettting out of that mode? Just reboot??? or??
REmoved because of inaccuracy..
WHOOOOOOOOOOAAAAAAAAAAA
Stop before u mess up. First off, they could have used jumpspl to flash the rom w/o having hard spl. Not recommended but possible.
First, put the phone in the tricolor screen and tell me what it says exactly.
I removed my post since it was wrong.
KAIS1*0 MFG
SPL-1.0.0liPof
CPLD-8
Thats what the screen says... and it is in the upper left corner
bigboyhf said:
KAIS1*0 MFG
SPL-1.0.0liPof
CPLD-8
Thats what the screen says... and it is in the upper left corner
Click to expand...
Click to collapse
If that is exactly what the screen says, then congratulations, you have hardspl already installed.
Thanks! Much appreciated...
Related
I went to HTC America's website and downloaded the software update for my 8125.
I ran the program and at 95% it said bad NBF file. When I turned my phone back on it goes to Bootloader mode and shows this:
{RUU (Top right corner)
IPL 2.25.0001 (Top left corner)
SPL 2.25.0001 (Below IPL)
USB (Bottom left corner when I connect the USB Cable)}
I downloaded a couple other roms and when i run them I get an Error 300.
ANY HELP PLEASE. HAVE I BRICKED?
download your ROM from htcamerica again and try again... your download had most probably been corrupted...
streetstockace said:
I went to HTC America's website and downloaded the software update for my 8125.
I ran the program and at 95% it said bad NBF file. When I turned my phone back on it goes to Bootloader mode and shows this:
{RUU (Top right corner)
IPL 2.25.0001 (Top left corner)
SPL 2.25.0001 (Below IPL)
USB (Bottom left corner when I connect the USB Cable)}
I downloaded a couple other roms and when i run them I get an Error 300.
ANY HELP PLEASE. HAVE I BRICKED?
Click to expand...
Click to collapse
You've got a G4 (notice the .0001????)
I'm pretty sure you bricked it. Luckily you were installing an OFFICIAL ROM so I'd call Cingular ... and stick to your guns!
I have re downloaded the rom from HTC several different times with the same results.
I've read that if I'm in Bootloader I haven't bricked. Any other help
THANKS AGAIN
Try this option showthread 276963 good luck
streetstockace said:
I have re downloaded the rom from HTC several different times with the same results.
I've read that if I'm in Bootloader I haven't bricked. Any other help
THANKS AGAIN
Click to expand...
Click to collapse
....before anyone moderates my ass i wasnt sure whch forum was the appropriate one for a bricking!
****
My phone seems to have given up the ghost. A few days after having put on the excellent Q-Mobile system. My phone has refused to boot properly. Heres what happens:
In start up from Soft reset, or Power off, i get the tricolour screen saying:
KAIS130 MFG
SPL-1.0 OliPof
CPLD-8
a few2 lines benath that is written 'Serial'
it then flashed onto a white screen saying 'loading......no image file' - this all takes about a second.
And then it rests on the screen mentioned above.
I haven't dropped it or done anything other than flash- correctly.
AAAARGH! it does randomly decide to boot up properly after its been left of for a whil if that helps.
Also - active synch wont recognise it , in the tr-colour state.
HELP!!!
Phone now stable
wondering what the best thing to do is to get it back on track...
i had same issue read the link to my post
http://forum.xda-developers.com/showthread.php?t=352859
mtty worked for me then i reflashed its worth a try i guess
kishorvalji said:
i had same issue read the link to my post
http://forum.xda-developers.com/showthread.php?t=352859
mtty worked for me then i reflashed its worth a try i guess
Click to expand...
Click to collapse
mtty is the way to do...you are not bricked...just take a few breaths and search the forums. When it happened to me, I had to use the BOOT command with MTTY. After it boots back up, run HARDSPL once again otherwise anytime you soft reset it will return to the bootloader screen.
thanks, but what is MTTY - i checked the posts and couldn't find it anywhere
I just got a att tilt.. I have tryed to unlock it using the kaiser sim unlocker. At first it would just go to the load screen and it would say 0%... a white screen. so i looked for a posting with that. And i found this ------HardSPL will not install - WHITE SCREEN: SOLVED (UPDATE 01. March 2008)-----
on that i got all the way up to 95% and then I got a err message.. now all it will do is go to the load screen (white) and show 0% and then I follow the instructions.. and when I go to restart the phone it show the red,green,blue,white screen.. top left show
kais1*0
spl-1.56.0000
cpld-8
top right show
ruunbh
what happen please help.. this is the first time this ever do this to me.. i have ren unlocked programs from hear befor with np..
bikepilot said:
I just got a att tilt.. I have tryed to unlock it using the kaiser sim unlocker. At first it would just go to the load screen and it would say 0%... a white screen. so i looked for a posting with that. And i found this ------HardSPL will not install - WHITE SCREEN: SOLVED (UPDATE 01. March 2008)-----
on that i got all the way up to 95% and then I got a err message.. now all it will do is go to the load screen (white) and show 0% and then I follow the instructions.. and when I go to restart the phone it show the red,green,blue,white screen.. top left show
kais1*0
spl-1.56.0000
cpld-8
top right show
ruunbh
what happen please help.. this is the first time this ever do this to me.. i have ren unlocked programs from hear befor with np..
Click to expand...
Click to collapse
It shows you are using the 1.56 SPL, which is the Stock AT&T SPL.
Download the official AT&T 6.0 Shipped Rom here:
http://rapidshare.com/files/55298724/RUU_Kaiser_CINGULAR_WWE_.exe
Take out your SD card and flash this ROM. After you have a successful flash and your phone boots up normally, post back and we'll go from there.
bengalih said:
It shows you are using the 1.56 SPL, which is the Stock AT&T SPL.
Download the official AT&T 6.0 Shipped Rom here:
http://rapidshare.com/files/55298724/RUU_Kaiser_CINGULAR_WWE_.exe
Take out your SD card and flash this ROM. After you have a successful flash and your phone boots up normally, post back and we'll go from there.
Click to expand...
Click to collapse
Ok I tried that it go to 1% and then it go to say
ERROR[294] : INVALID VENDER ID
this update untility cannot be used for you pda phone pleas check you Update utility
bikepilot said:
Ok I tried that it go to 1% and then it go to say
ERROR[294] : INVALID VENDER ID
this update untility cannot be used for you pda phone pleas check you Update utility
Click to expand...
Click to collapse
You could try this
More specifically, might want to read this whole thread and search it for RUUNBH.
MTTY should be able to help as long as you use the proper commands.
bengalih said:
You could try this
More specifically, might want to read this whole thread and search it for RUUNBH.
MTTY should be able to help as long as you use the proper commands.
Click to expand...
Click to collapse
Ok got it back to all origanal...now every time i take the battery it go back to the colar screen ( now what
Dear friends,
maybe today I missed forever my jewel. I was updating it by using the latest ROM from PDJOS and the update procedures stopped itself on 16%.
Now it starts with the following:
KAIS130
SPL-1.56.0000
CPLD-8
USB
Active sync doesn't recognize the device as well as any flashing utility.
Does anyone can give me any tips?
Thanks!
Maybe try flashing via the SD card. Just a thought.
MTTY
http://forum.xda-developers.com/showthread.php?t=371154
KAIS130
SPL-1.56.0000
CPLD-8
This means theres no HardSPL amirite?
T.T you gotta install HardSPL first.
Imsaffor said:
KAIS130
SPL-1.56.0000
CPLD-8
This means theres no HardSPL amirite?
T.T you gotta install HardSPL first.
Click to expand...
Click to collapse
+1 This is your answer. You need to install HardSPL.
JimmyMcGee said:
+1 This is your answer. You need to install HardSPL.
Click to expand...
Click to collapse
Thanks for the reply! So I'm trying with this tool:
http://forum.xda-developers.com/showthread.php?t=375583
but the device when goes on the white screen stops itself on 0% (the flash doesn't start).
How do I do now?
Thanks once again,
sev7en said:
Thanks for the reply! So I'm trying with this tool:
http://forum.xda-developers.com/showthread.php?t=375583
but the device when goes on the white screen stops itself on 0% (the flash doesn't start).
How do I do now?
Thanks once again,
Click to expand...
Click to collapse
You really need to stop and read the WIKI. Read the part about what to do when you get a white screen?
Bill
whk said:
You really need to stop and read the WIKI. Read the part about what to do when you get a white screen?
Bill
Click to expand...
Click to collapse
I read it carefully but there's something that doesn't work.
So, when now I power-up my Kaiser it goes on the boot screen (USB mode). I have already disabled the active sync connection on my PC.
Now I launch the flash-hardSPL (I tried the v3.28 as well as the v3.29) and the device goes into the white screen where there's the progression bar.
At this point, it don't go ahead and... from 0%.
I'd recommend getting your device back to working order again by flashing with the Official Rom for you Carrier or HTC if it's an unbranded device.
The you can again resume working on HardSPL & such.
Without a working OS (WindowsMobile) you can't use Soft/JumpSPL which is required to flash HardSPL.
I recovered it! Finally!!!
I used the mtty then successfully patched the SPL.
Thanks to all for this awesome forum and of course your sharing spirit ^_^
HI , friends i been trying to sim unlock my new tytn2 which is in uk orange network now.
I tried to install hard spl, i m new to this technical worlds like cooked rom, new hard spl etc ,.any one please tell me how to do this step by step,
When i tried to install hard spl, there comes a tricolor screen first white screen with progress bar 0% , and after some time it stucks and in pc shows error message. tried with jump spl method described by some one, in the kaiser section, what is the meaning of wm6 and wm6.1
Following are the details of my phone
R 1.27.12.29
G 22.45.88.07H
D 1.81.00.00
KAIS130
SPL-1.81.0000
CPLD-8
What should i do to get my phone unlocked, plz help i assure 5 pounds to the one who has time to help me in this. cheers friends.
WM6 and WM6.1 are Versions of Windows Mobile, see Settings, About on your phone.
Looking at the Radio version, you are a WM6.0 user still.
To install Hard SPL read here: http://forum.xda-developers.com/showthread.php?t=334679
If you get a white screen, read here: http://forum.xda-developers.com/showthread.php?t=354061
Once you have Hard SPL complete, you can SIM Unlock, read here: http://forum.xda-developers.com/newreply.php?do=newreply&noquote=1&p=2572785
I suggest you read here Getting Started and on the XDA Wiki, there is lots of information on the HTC Kaiser page that covers the basics.
It is appreciated to search and read before posting new threads when the information is already available. If you get stuck with one part, re-read the thread, search for your problem, and then (and only then) post in the thread you are trying to follow.
Thanks
Dave
thanks dave.but i tried it, i couldnt even install hard spl, i dont know what happens when i run jumpspl also it shows white screen no further actions takes place. i dont know what to do now.
pappoos4u said:
thanks dave.but i tried it, i couldnt even install hard spl, i dont know what happens when i run jumpspl also it shows white screen no further actions takes place. i dont know what to do now.
Click to expand...
Click to collapse
Try SSPL First, then JumpSPL 1.56, then JumpSPL 1.93. one should work.
Ta
Dave
pappoos4u said:
...i dont know what happens when i run jumpspl also it shows white screen no further actions takes place...
Click to expand...
Click to collapse
Dave's second link above says "If you get a white screen..."