Help Help Help
Iam new to the flashing
I have herald (HTC P430 HERA) with wm5 ,i tried to upgrade to wm6 with TOUCH-IT.I installed the SPL and then ran the RUU ,everything was perfect the installation started normally ,durin the installation i chose the option to use the keylock ,when my htc started it kept on asking me the password on the device which i entered but it did not accepted .i kept on trying and eventually took out the battery.When i restarted the device it got showed a green scnreen with spl 1.08.000 and the turned off i tried going in to the boot ,loader but everytime i run the same ruu it gives me erorr 300 i have tried several time donwloaded each adn every ruu but all in vain and im in pain .sometime the screen get stuck on 0% . Can somebody help or atleast direct me to the right area.
Related
i need some serious help im desperate at this stage.
ive basically got a htc tytn ii on uk orange
i update the rom to htc standard one which sim locked it
i followed the instruction on how to get it like i got it from orange
which i believe was sucessful. but because it was still sim locked i
thought the hardspl was relocked so i ran that again which failed and ended up on the tri colour screen after which i tought it may still be hardspl locked
so i tried to flash it with the rom again it got to 17% then crashed
now my phone will only boot to the tricolour screen it wont load activesync and if i try a flash it with anyrom it either stays at 0% gets stuck or gets to 1% then the phone restarts.
ive buggered the phone up proper i need some help if there is any for this mess
when i try a rom upload it says error [294]: invalid vender id
this update utility cannot be used for your pda phoe please check your update utility
Did you install Hard SPL?
http://forum.xda-developers.com/showthread.php?t=334679
See if you can install that and then try to reinstall your rom.
this required activesync to be green mine will respond to usb but not activesynce so i cant go any further with the hardspl unlock im stuck on the tricolour screen. and flashing will only go to 1% then restart and the message come up again.
same problem
i have the same problem and i can only get to 1% . i have tried to flash it with several roms using diferent utilities and none seem to work i used hard spl the first time when it failed. HELP PLEASE !!!!!!!
found solution
got mine working here is what i did
run mtty select usb after disabling it in activesync
press enter and you should see cmd>
type boot and when your device restarts it should start in your old rom
run hardspl again
then you need to reinstall your rom
although a word of warning my phone became sim locked after this
worked a treat many thanks it is sim locked just have to wait for the sim unlock for it now
willbyrne said:
got mine working here is what i did
run mtty select usb after disabling it in activesync
press enter and you should see cmd>
type boot and when your device restarts it should start in your old rom
run hardspl again
then you need to reinstall your rom
although a word of warning my phone became sim locked after this
Click to expand...
Click to collapse
no worries
yeah no worries, i was affraid when i locked mine i might have to return it and get anothe orange version but i used some company online and got my code in about 3 days.
oh yeah you will probably need to enter the code in twice, mine said simlocked and then network locked but it was the same code
Hi all,
I have been visiting these forums for 2 years now and have downloaded some great tools and ROMs to enhance my Trinity, however something all of a sudden has gone very wrong!
I upgraded to WM6.1 Elegance edition about 3/4 months ago, CID unlocked the phone about a month ago and everything has been working like a dream.
However just today, I attempted to turn the volume down on my phone during a meeting (I always forget to normally!) and there was no display. After few battery resets, again no display. It starts up, loads the the Elegance splash screens and then hangs on the screen before when the OS should appear.
My decision was to flash the ROM again. I cant flash using Activesync as it wont pick up on the hung screen, so I started the bootloader and got as far as 1% of the flash and it will restart. So I tried the SD Card method when resulted in a "loading" screen appearing for a few seconds and then it goes back to the standard bootloader and displayed a 00068002 error.
I am out of ideas, I hear mtty.exe is a good program for this kind of thing, but what I want to know is if this is fixable or if I should give up!
I have been working on this since 2pm today none stop!
Can any of you guys give me any suggestions please?!?!?
Kind regards,
Jonathan
Should be a cinch
Did you SPL the Phone before flashing roms?
If you put the phone into the bootloader mode The RGB screen and kill of activesync you should be able to run one of the flash update programs.
If I have flashing problems its usually Active sync so I kill it then run the flash program.
I've got a sneaky suspision your battery might be causing the problem.
Hi there, thanks for the reply. As I was new to upgrading I havent used SPL on the phone before flashing the ROMS. I did use an unlock tool recently as i wanted to try a different network SIM to see if it worked when I was in South America, so the phone is unlocked to all networks. Are you saying if I SPL now it should sort the problem out? If so how do I do this withour ActiveSync working - can you use SD?
Another thing I failed to mention was that when I start an upgrade and it follows all the steps, it doesnt say the current ROM on the screen where you press update ROM. It just gives the name of the new ROM and the current one is left blank.
I have disabled Active Sync before attempting the update. It seems to go through fine and then the phone restarts wafter 1% of the update.
What makes you think it is the battery? I am happy to spend under 20 pound on ebay if you think it will fix the issue!
try unbrick.bat.......my trinity was also stuck.......unbrick.bat save my day....
The same happened to me several time....I could not find a solution other than this one:
1. Flash the official HTC ROM.
2. Flash the required ROM then.
it works for my TrinTy.
Hi
I have this problem if i want to update my SPL to HardSPL, i does not flased anything yet, because i get my phone today!
Try another version of HardSPL.
i second that use a differant one.
I tried all Versions of HardSPL but nothing works ...
btw. is it rght to go into the colored screen by turning off the phone, then turn it on with the volume down button?
depends what version diamond rom you have and to wich rom you want to upgrade, its usually mentioned wich spl is best in the rom-thread
rushing into this forum and blindly flashing can lead to a brick aka dead phone so take great care when proceeding
I'm having the same issues and I tried all the HardSPL versions myself.
once the upgrade begins, the phone screen just hangs and the installation is stuck at 0% for a while. After which it gives me either one of the following errors:
Error 202 Connection
Error 260 Connection
Only a restart of the phone will release it from the hang.
Yes I used it, but no luck.
@ some 1
even i got same problem with my diamond i m not able to understand where i went wrong...any help appreciated
same proplem
i have same proplem.. first everything looks just fine but when i try to update it stuck couple of seconds at 0% and then it gives error 202
same problem here..
+1
+1
+1
+1
+1
+1
+1.................
Hello everybody.
So the problem is this. I got a QTEK 9100 today, and it happened to be in swedish (got in from a friend, for free). It was WM5 anyway so i decided to update it to WM6 or newer. I followed the original guide to flash rom (i did everything as they were supposed to do) I got the Wizard Service tool, checked the right G-thing. I do have G3 device and i did follow the G3 guide.
But when i tried to flash it did came with an ERROR 262 CONNECTION ERROR. And then it put me to the recovery instructions. I went them trough -cable off, power off, cable back, power back) I tried to re-flash it three times, but it was ALWAYS stuck at 26% giving the same error over and over again.
I re-installed Activesync. I didnt get no connection this time (before reinstall i did get connection). Altrough my computer says something at lower right that it detected a device.
Then i tried Xda_MiniS_LaunchROM_v154102. I tried it two times, same error 262 and stuck at 11%.
Now it wont upgrade to anything. CID is still locked.
Im stuck in the three color space at the beginning. My IPL is 1.05 and SPL is 2.17. I do get the USB in bottom left of the screen.
Any help would be appreticiated. I dont want to brick my new phone.
Greetings. Hurrikaani
have you tried to flash button rom on your device?
Hi folks,
i used several roms from here, worked nicely.
had spl 1.33.OliNex i downloaded latest energy rom and did update from SD.
it wrote update success, then i reseted topaz.
now im stuck on boot screen with tmobile logo and RDG message.
i tryed to upgrade radio and do the flash again but again success message and screen hang on tmobile logo. tryed hard resets etc, same result.
i just got
R 4 49 25 91
G 61.44etc 25 35U
D2.13.64695
message on bottom, nothing more.
i wonder if its not problem that i have older hspl, but i dont know how to upgrade it without having system booted and connected to PC...
Anybody can help me?
-------------------------
managed to update spl to 2.51,
did the flash again, again success message and this time it runs
So, maybe it will at least help other ppl
grapher said:
Hi folks,
i used several roms from here, worked nicely.
had spl 1.33.OliNex i downloaded latest energy rom and did update from SD.
it wrote update success, then i reseted topaz.
now im stuck on boot screen with tmobile logo and RDG message.
i tryed to upgrade radio and do the flash again but again success message and screen hang on tmobile logo. tryed hard resets etc, same result.
i just got
R 4 49 25 91
G 61.44etc 25 35U
D2.13.64695
message on bottom, nothing more.
i wonder if its not problem that i have older hspl, but i dont know how to upgrade it without having system booted and connected to PC...
Anybody can help me?
-------------------------
managed to update spl to 2.51,
did the flash again, again success message and this time it runs
So, maybe it will at least help other ppl
Click to expand...
Click to collapse
Did you try going into bootloader first and then running the RUU.exe?
Or you can look HERE about making a Goldcard with Qmat (#6)
EDIT: Didn't see that you updated your post, congrats on gettin it workin again though