Related
warnning; does not work with g4 wizards!!!!!
this steps are to cid unlock and also to unlock sim in the folowing devices; qtek 9100, i-mate k-jam, mda vario, orange spv m3000, o2 xda mini s, dopod 838, Cingular 8125
first; you must make a full backup of you wizard before doing this , I personally use [wizBackup.exe] posted below for my backups and restores. This is not mandatory but could save an enormous amount of trouble.
I as most people with a wizard with the aku2 rom found out that it cannot be cid unlock with lokiwiz tool, you will get the following;{error:itwritedisk-an internal error occurred}.
. that is till now.
downgrade rom here http://dl.dropbox.com/u/7696581/htc%20wizard/CUSTOM__RUU_Wizard_1050412_WWE_101_11210_WWE.exe
note- this steps is for unlocking the cid of the wizard with aku2 rom.
how to cid. unlock all wizard variants ( that have the latest rom build )
first download custom__ruu_wizard_1050412_wwe_101_11210_wwe. rom from the ftp site from the above link, unpack it and just click the romupdateutility_wizard_noid.exe to start downgrading. Simply follow the prompts.
after the rom are loaded go thru the initial setup as you would with any rom.
now download the (lokiwiz02b) from here;
http://dl.dropbox.com/u/7696581/htc wizard/CUSTOM__RUU_Wizard_1050412_WWE_101_11210_WWE.exe
Make sure you unzip lokiwiz to the root o the c: drive.
please copy the whole lokiwiz folder to the root of the drive,not the contentents of the folder!!!!!
and follow the instructions .do not forget to copy the cab file(enable rapi) to your device and run it before running lokiwiz.
Now run lockiwiz and unlock your machine, your machine will reboot itself. if yoy see an eroot while unlocking that says;
..............................................................................................................................................................................
CopyFileToTFFS(cidunlocked.bin:0, 0, 00010000)
ERROR: ITWriteDisk - An internal error occurred.
this means that you device not been unloked......try again............
.................................................................................................................................................................................
That’s it your wizard is unlocked. Make sure yew keep the [lock_backup.bin] in a safe place you may need it for guaranty purposes.
Now flash the latest aku2 rom from your provider.- [very important,to avoid future problems wit rom updates]
then u can flash any rom you want.
question: if i cid unlock and sim unlock my phone (after installing custom 1.5 wwe rom) and then i install latest aku2 i-mate italian rom, will the sim unlock (and cid one too) be preserved?
Answer: i can confirm that that upgrading to the latest aku2 rom the wizard remains cid unlocked.
Special thanks to the author of the above cooked rom [button] also to machinagod for the lokiwiz tool and joninla for finding the downgrade rom, molski for is input and everyone that contributed to the cause.
do not try to downgrade using an older wizard rom other than the one posted above it will not work
also this {how to} is for the htc wizard only it may work with other devices but i don’t know, so if you turn you device into a brick do not blame me. use it at your own risk
if you device is from a operator like: 02, orange etc... You will void your guaranty unlocking cid, but don’t despair, if you keep the [lock_backup.bin] file that the lockiz tool generated you can restore cid to factory default.
this proccess only needs to be done once in the wizards lifetime.
Enjoy;
Jose faria.
donate if you like my work
Faria, can you tell me if this process will do it for the HTC Prophets with rom 2.x ???
I've got an imate JAMin with aku2 from factory. Just downloaded older Imate Rom... will try the process when i get home
8) wish me luck
maybe if you find an older rom for you device i only have a wizard.take a look at the lokiwiz tread i belive tha someone mentioned the HTC Prophets.
jamichy said:
I've got an imate JAMin with aku2 from factory. Just downloaded older Imate Rom... will try the process when i get home
8) wish me luck
Click to expand...
Click to collapse
Bet I will!!
For the record, your Jamin's rom is the same that was available to download some weeks ago with the Aku2??
jamichy said:
I've got an imate JAMin with aku2 from factory. Just downloaded older Imate Rom... will try the process when i get home
8) wish me luck
Click to expand...
Click to collapse
let me know how you get on.
onesolo said:
Faria, can you tell me if this process will do it for the HTC Prophets with rom 2.x ???
Click to expand...
Click to collapse
it may be possible,if you have an old custom rom for your device ,found this;
On the one hand, HTC Prophet is a complete copy (both software and hardware are meant) of HTC Wizard. On the other hand, it's equal to HTC Magician in appearance. That is why today review will be quite short, we will only discuss external elements and a new camera, all other aspects were highlighted in the review of HTC Wizard.
http://www.mobile-review.com/pda/review/htc-prophet-en.shtml
Hi Faria, thank you for your HowTo!
Now i know the wizard remains CID unlocked after the upgrade and that's good. I only hope that it stays SIM unlocked too.
Bye
Sadly, cant move back to older rom... keep getting error message saying the nk.nbf file is not valid/older than your current file.
I guess we just have to wait for an updated version of Lockiwiz
sh*t forgot to post the address to the downgrade rom.here it ftp://xda:[email protected]__RUU_Wizard_1050412_WWE_101_11210_WWE.exe
sorry guys
jamichy said:
Sadly, cant move back to older rom... keep getting error message saying the nk.nbf file is not valid/older than your current file.
I guess we just have to wait for an updated version of Lockiwiz
Click to expand...
Click to collapse
yes u can, use this rom to downgrade
ftp://xda:[email protected]__RUU_Wizard_1050412_WWE_101_11210_WWE.exe
faria said:
jamichy said:
Sadly, cant move back to older rom... keep getting error message saying the nk.nbf file is not valid/older than your current file.
I guess we just have to wait for an updated version of Lockiwiz
Click to expand...
Click to collapse
yes u can, use this rom to downgrade
ftp://xda:[email protected]__RUU_Wizard_1050412_WWE_101_11210_WWE.exe
Click to expand...
Click to collapse
Hello, could you please tell me what is changed in the custom ROM???
I am willing to do the same thing for the prophet.
Thanks
nothing except i did not post the link to the rom by mistake,did you use an old i-mate rom to downgrade? do not it will not work, use the one in the above link.thats the only one that it will work that a know for sure.
faria said:
nothing except i did not post the link to the rom by mistake,did you use an old i-mate rom to downgrade? do not it will not work, use the one in the above link.thats the only one that it will work that a know for sure.
Click to expand...
Click to collapse
You mean to use the wizard rom on the prophet?
Won't that overwrite the bootloader with the one for the wizard???
andrew_sh said:
faria said:
nothing except i did not post the link to the rom by mistake,did you use an old i-mate rom to downgrade? do not it will not work, use the one in the above link.thats the only one that it will work that a know for sure.
Click to expand...
Click to collapse
You mean to use the wizard rom on the prophet?
Won't that overwrite the bootloader with the one for the wizard???
Click to expand...
Click to collapse
haaa you have the prophet
dont do that it may turn the prophet into a brick the only way is to find an old custom rom for your device. take a look at the ftp site it may have one there.
sorry
I told you Faria that it can be done
Great that it worked out okay, I can imagine how happy you are feeling right now
Nice how-to by the way.
mm..i am currently using T-mobile MDA Vario with the original rom
is that mean i don't have to apply it to unlock the cid?
i just use the lokiwiz 2b to unlock the CID, after it, even i upgrade to the newest rom e.g. the new O2 rom, my CID still remain unlock?
siupiu said:
mm..i am currently using T-mobile MDA Vario with the original rom
is that mean i don't have to apply it to unlock the cid?
i just use the lokiwiz 2b to unlock the CID, after it, even i upgrade to the newest rom e.g. the new O2 rom, my CID still remain unlock?
Click to expand...
Click to collapse
THATS IT.
siupiu said:
mm..i am currently using T-mobile MDA Vario with the original rom
is that mean i don't have to apply it to unlock the cid?
i just use the lokiwiz 2b to unlock the CID, after it, even i upgrade to the newest rom e.g. the new O2 rom, my CID still remain unlock?
Click to expand...
Click to collapse
THATS IT.
good, really thx~~^_^
After applying the 2.21.4.1 latest update for my XDA mini s i've found that the reception's not as good as the previous 1.5.4.102 version. I tried to reflash the software with the original rom from the o2 website but it won't allow me to downgrade back to how it was before. I've also tried the various radio roms available from this forum, but the reception's still not as good as it was before applying the upgrade
Is it possible to downgrade back to the original shipping software or not?
Thanks!
adam p said:
After applying the 2.21.4.1 latest update for my XDA mini s i've found that the reception's not as good as the previous 1.5.4.102 version. I tried to reflash the software with the original rom from the o2 website but it won't allow me to downgrade back to how it was before. I've also tried the various radio roms available from this forum, but the reception's still not as good as it was before applying the upgrade
Is it possible to downgrade back to the original shipping software or not?
Thanks!
Click to expand...
Click to collapse
You'll need to downgrade, CID unlock, and then move to your desired ROM. To downgrade successfully though, you'll need the 1.x ROM packaged with the no-ID installer. Look through the first few pages of posts for a message that says something like "Solution found for downgrading 2.x ROMs".
summiter said:
You'll need to downgrade, CID unlock, and then move to your desired ROM. To downgrade successfully though, you'll need the 1.x ROM packaged with the no-ID installer. Look through the first few pages of posts for a message that says something like "Solution found for downgrading 2.x ROMs".
Click to expand...
Click to collapse
That, unfortunately, does not work for the AKU 2.2 (version 2.21) and up ROMs.
[/quote]That, unfortunately, does not work for the AKU 2.2 (version 2.21) and up ROMs. [/quote]
So there's no way to go back? When I phoned O2 I specifically asked if the new radio would give me better reception and they said 'yes'. If i'd have known it would be for the worse then I wouldn't have bothered installing the upgrade :twisted:
Extract the rom you want to update. Make sure you place all the files in one folder. I used Win Rar to extract the rom. Make sure you have nk.nbf, ROMUpdateUtility.exe and along with all the other files. Replace RUUGetInfo.exe with the one I have attached. It will trick your Wizard thinking that it is on a lower ROM version so that you can do the update. Then run the ROMUpdateUtility.exe, and everything should be the same.
Any idea where I can get nk.nbf, ROMUpdateUtility.exe
I've done a search on this forum but can't find it anywhere.
adam p said:
Any idea where I can get nk.nbf, ROMUpdateUtility.exe
I've done a search on this forum but can't find it anywhere.
Click to expand...
Click to collapse
You downloaded the Update (RUU_Prodigy_2210206_22102109_021911_TMO_UK_WWE_Ship.exe).
Just rename it to RUU_Prodigy_2210206_22102109_021911_TMO_UK_WWE_Ship.rar and open it with Winrar.
Sorry if you think i'm stupid but I don't know much about pc's.
What i've done so far is to download the original shipping rom from the o2 website, extract the contents into 1 folder, replaced the RUUGetInfo.exe rom with the one supplied by phouki and clicked on the ROMUpdateUtility.exe to start the update. It displayed an error message about 5-10 seconds into the update saying that I need a newer version of nk.nbf and this is where I don't know what to do next.
Your help is very much appreciated and thanks in advance.
adam p said:
Sorry if you think i'm stupid but I don't know much about pc's.
What i've done so far is to download the original shipping rom from the o2 website, extract the contents into 1 folder, replaced the RUUGetInfo.exe rom with the one supplied by phouki and clicked on the ROMUpdateUtility.exe to start the update. It displayed an error message about 5-10 seconds into the update saying that I need a newer version of nk.nbf and this is where I don't know what to do next.
Your help is very much appreciated and thanks in advance.
Click to expand...
Click to collapse
Search for RomUpdateUtility_NoID.exe download it and use it instead of RomUpdateUtility.exe
It's flashed using that method but now my XDA is saying that it's the same ROM as I had previously:
ROM version: 2.21.4.1 WWE
ROM date: 3/9/06
Radio version: 02.07.10
Protocol version: 413.1.03
ExtROM version: 2.21.4.101
Is this because the ROM has been tricked so it still displays the latest ROM version even though it's flashed back to the shipping rom?
adam p said:
It's flashed using that method but now my XDA is saying that it's the same ROM as I had previously:
ROM version: 2.21.4.1 WWE
ROM date: 3/9/06
Radio version: 02.07.10
Protocol version: 413.1.03
ExtROM version: 2.21.4.101
Is this because the ROM has been tricked so it still displays the latest ROM version even though it's flashed back to the shipping rom?
Click to expand...
Click to collapse
Which method is "that method"?
When you have been given more than one suggestion, please quote back part of the post so we know which one you're referring to.
Please list exactly the steps you used to flash with the original shipping rom.
1) I downloaded the original shipping rom Xda_MiniS-LaunchRomv154102 from the o2 website
2) Extracted the contents into 1 folder using WinRar
3) Replaced the RUUGetInfo.exe rom with the one supplied by phouki
4) Replaced RomUpdateUtility.exe with ROMUpdateUtility_Wizard_NoID
5) Clicked on the ROMUpdateUtility_Wizard_NoID to start the upgrade.
The phone dialer skin has changed back to how it was when I bought the phone so I presume it's worked to some extent but couldn't be 100% sure with it still saying it's got the updated ROM version of 2.21.4.1 WWE
ROM date: 3/9/06 and Radio version: 02.07.10
adam p
Try to reflash it again with same or some older ROM..
Worked for me :roll:
And give IPL/SPL info, pls.
adam p said:
The phone dialer skin has changed back to how it was when I bought the phone so I presume it's worked to some extent but couldn't be 100% sure with it still saying it's got the updated ROM version of 2.21.4.1 WWE
ROM date: 3/9/06 and Radio version: 02.07.10
Click to expand...
Click to collapse
Can't be sure but I'd guess not. If the RUU thinks you flashed good then it will hard reset which would do that.
Skwyk said:
adam p
Try to reflash it again with same or some older ROM..
Worked for me :roll:
And give IPL/SPL info, pls.
Click to expand...
Click to collapse
I've tried reflashing it again and it's exactly the same. The IPL is 1.05 and SPL is 2.21. It's asking me to choose between 'basic' and 'corporate' settings when customizing. The only thing I can see that's changed is the phone skin.
Where can I get any older ROMs for it than than v15402?
adam p said:
I've tried reflashing it again and it's exactly the same. The IPL is 1.05 and SPL is 2.21. It's asking me to choose between 'basic' and 'corporate' settings when customizing. The only thing I can see that's changed is the phone skin.
Where can I get any older ROMs for it than than v15402?
Click to expand...
Click to collapse
You're not going to get any love with other ROMs until you CID unlock. Because you upgraded to 2.21 before CID unlocking there are no free solutions.
Hit up http://imei-check.co.uk (and no, I don't have anything to do with them) and pay the £20. That should SIM and CID unlock your phone. At that point, you should be able to reflash the older ROM without issue.
downgrading
I tried this solution and it also didnt work for me trying to downgrade from the new cingular release back to the old qtek one. I however found a solution that did work for me here
http://forum.xda-developers.com/viewtopic.php?t=47848
hope it helps
Re: downgrading
flipwalter76 said:
I tried this solution and it also didnt work for me trying to downgrade from the new cingular release back to the old qtek one. I however found a solution that did work for me here
http://forum.xda-developers.com/viewtopic.php?t=47848
hope it helps
Click to expand...
Click to collapse
Adam P,
Use the link flipwalter posted (in the quote). You might be toasted already though. If that process doesn't work the you need to get a 1.x Rom from your Carrier (is it O2?) and extract the RUU & nk.nbf files. Then use the RRUGetInfo file from the earlier post to try to get the older rom onto your phone.
That failing, you need to either dump 20 pounds to imeicheck for thier CID unlock.
DONE!
IPL: 1.05
SPL: 1.05
Had to pay the £20 for the CID unlock but i'm well pleased. Many thanks for all your help
adam p said:
DONE!
IPL: 1.05
SPL: 1.05
Had to pay the £20 for the CID unlock but i'm well pleased. Many thanks for all your help
Click to expand...
Click to collapse
Happy flashing!!!! :lol:
Hello everybody !!
I just spent about 28 hours reading the threads in order to change my GERMAN O2 XDA MINI S (Wizard) ROM. Into an english one.
For that matter I know I need to unlock my CID, but since i have the latest ROM installed, IPL 2.21.001 and SPL 2.21.001 Lockwiz won't work !!!!
so I tried to Downgrade my Rom in order to make the Lockwiz work, but I am not able to find a suiting German Rom anywhere on the Net.
So I was wondering if nebody would be kind enough to tell me where to find and older German ROM or how I can avoid DOWNGRADING and simply unlock my CID
best regards ... Bayardo
I3aYardo said:
Hello everybody !!
I just spent about 28 hours reading the threads in order to change my GERMAN O2 XDA MINI S (Wizard) ROM. Into an english one.
For that matter I know I need to unlock my CID, but since i have the latest ROM installed, IPL 2.21.001 and SPL 2.21.001 Lockwiz won't work !!!!
so I tried to Downgrade my Rom in order to make the Lockwiz work, but I am not able to find a suiting German Rom anywhere on the Net.
So I was wondering if nebody would be kind enough to tell me where to find and older German ROM or how I can avoid DOWNGRADING and simply unlock my CID
best regards ... Bayardo
Click to expand...
Click to collapse
Since you have a G4 boot chip (the tailing .001 in IPL and SPL tells that) you CANNOT downgrade your ROM to 1.x version.
DO NOT TRY INSTALLING A 1.X ROM: YOU'LL BRICK YOUR PPC!!! DO NOT FOLLOW FARIA's PROCEDURE TO CID UNLOCK 2.X PHONES: IT WON'T WORK IN YOUR CASE ('cos you've got a G4 boot chip).
This means that you will NOT be able to CID/SIM unlock your phone with lokiwiz 0.2b (however you can still use lokiwiz 0.3a to SIM unlock it, but no CID unlock).
But don't despair, you CAN still change your phone language and install whatever 2.x rom you like. The procedure to follow, however, is a bit different: you cannot simply download a rom you like and install it, you'll need to hack it a little first, but the results will be the same!
Basically, all you have to do is get the ROM you like (only 2.xx ROM!!!) and remove from it the IPL/SPL part. Then, you have to flash this 'hacked' rom using a slightly modified ROM Upgrade Utility (i can provide it to you if you want). With this method you're not going to replace the IPL/SPL (bootloader) of your phone so you don't need to CID unlock it (which, at the time i'm writing, is impossible).
To remove IPL/SPL from your ROM you have to extract the file nk.nbf from the ROM and get its content with typho5 tool (search this forum to have more info). Then you have to reassemble a new nk.nbf using nb2nbf. The new nk.nbf, of course, must NOT contain the IPL/SPL parts.
If you prefer, you can tell me what ROM are you interested in and i'll do the dirty work for you. Just let me know.
Bye
Basically, all you have to do is get the ROM you like (only 2.xx ROM!!!) and remove from it the IPL/SPL part. Then, you have to flash this 'hacked' rom using a slightly modified ROM Upgrade Utility (i can provide it to you if you want). With this method you're not going to replace the IPL/SPL (bootloader) of your phone so you don't need to CID unlock it (which, at the time i'm writing, is impossible).
To remove IPL/SPL from your ROM you have to extract the file nk.nbf from the ROM and get its content with typho5 tool (search this forum to have more info). Then you have to reassemble a new nk.nbf using nb2nbf. The new nk.nbf, of course, must NOT contain the IPL/SPL parts.
Click to expand...
Click to collapse
I would be very thankful if you could post a link or send me the ROM upgrade Utility needed
best regards
Bayardo
risidoro said:
I3aYardo said:
Hello everybody !!
I just spent about 28 hours reading the threads in order to change my GERMAN O2 XDA MINI S (Wizard) ROM. Into an english one.
For that matter I know I need to unlock my CID, but since i have the latest ROM installed, IPL 2.21.001 and SPL 2.21.001 Lockwiz won't work !!!!
so I tried to Downgrade my Rom in order to make the Lockwiz work, but I am not able to find a suiting German Rom anywhere on the Net.
So I was wondering if nebody would be kind enough to tell me where to find and older German ROM or how I can avoid DOWNGRADING and simply unlock my CID
best regards ... Bayardo
Click to expand...
Click to collapse
Since you have a G4 boot chip (the tailing .001 in IPL and SPL tells that) you CANNOT downgrade your ROM to 1.x version.
DO NOT TRY INSTALLING A 1.X ROM: YOU'LL BRICK YOUR PPC!!! DO NOT FOLLOW FARIA's PROCEDURE TO CID UNLOCK 2.X PHONES: IT WON'T WORK IN YOUR CASE ('cos you've got a G4 boot chip).
This means that you will NOT be able to CID/SIM unlock your phone with lokiwiz 0.2b (however you can still use lokiwiz 0.3a to SIM unlock it, but no CID unlock).
But don't despair, you CAN still change your phone language and install whatever 2.x rom you like. The procedure to follow, however, is a bit different: you cannot simply download a rom you like and install it, you'll need to hack it a little first, but the results will be the same!
Basically, all you have to do is get the ROM you like (only 2.xx ROM!!!) and remove from it the IPL/SPL part. Then, you have to flash this 'hacked' rom using a slightly modified ROM Upgrade Utility (i can provide it to you if you want). With this method you're not going to replace the IPL/SPL (bootloader) of your phone so you don't need to CID unlock it (which, at the time i'm writing, is impossible).
To remove IPL/SPL from your ROM you have to extract the file nk.nbf from the ROM and get its content with typho5 tool (search this forum to have more info). Then you have to reassemble a new nk.nbf using nb2nbf. The new nk.nbf, of course, must NOT contain the IPL/SPL parts.
If you prefer, you can tell me what ROM are you interested in and i'll do the dirty work for you. Just let me know.
Bye
Click to expand...
Click to collapse
Hi risidoro,
I am trying upgrade my O2 German Wizrad G4 version into WWE, I followed your instruction & has used nb2nbf to compile a 2.xx rom without IPL & SPL. When I used the update utility to falsh the Wizard, the utility said something like: Error, this update utility is not for your device. etc.
I think I need to used your modified update utility , can you send it to me?
Also my other question is, when I use nb2nbf , what should I put in the model id for my German Wizard?
You advice can help me & many others to solve our headache in upgrading a G4 Rom! Cheers!
phone_one said:
Hi risidoro,
I am trying upgrade my O2 German Wizrad G4 version into WWE, I followed your instruction & has used nb2nbf to compile a 2.xx rom without IPL & SPL. When I used the update utility to falsh the Wizard, the utility said something like: Error, this update utility is not for your device. etc.
I think I need to used your modified update utility , can you send it to me?
Also my other question is, when I use nb2nbf , what should I put in the model id for my German Wizard?
You advice can help me & many others to solve our headache in upgrading a G4 Rom! Cheers!
Click to expand...
Click to collapse
The modified RUU (ROM Update Utility) is attached.
For ModelID you can use both WIZARD or Prodigy (i used the former).
risidoro said:
Since you have a G4 boot chip (the tailing .001 in IPL and SPL tells that) you CANNOT downgrade your ROM to 1.x version.
DO NOT TRY INSTALLING A 1.X ROM: YOU'LL BRICK YOUR PPC!!! DO NOT FOLLOW FARIA's PROCEDURE TO CID UNLOCK 2.X PHONES: IT WON'T WORK IN YOUR CASE ('cos you've got a G4 boot chip).
This means that you will NOT be able to CID/SIM unlock your phone with lokiwiz 0.2b (however you can still use lokiwiz 0.3a to SIM unlock it, but no CID unlock).
But don't despair, you CAN still change your phone language and install whatever 2.x rom you like. The procedure to follow, however, is a bit different: you cannot simply download a rom you like and install it, you'll need to hack it a little first, but the results will be the same!
Basically, all you have to do is get the ROM you like (only 2.xx ROM!!!) and remove from it the IPL/SPL part. Then, you have to flash this 'hacked' rom using a slightly modified ROM Upgrade Utility (i can provide it to you if you want). With this method you're not going to replace the IPL/SPL (bootloader) of your phone so you don't need to CID unlock it (which, at the time i'm writing, is impossible).
To remove IPL/SPL from your ROM you have to extract the file nk.nbf from the ROM and get its content with typho5 tool (search this forum to have more info). Then you have to reassemble a new nk.nbf using nb2nbf. The new nk.nbf, of course, must NOT contain the IPL/SPL parts.
If you prefer, you can tell me what ROM are you interested in and i'll do the dirty work for you. Just let me know.
Bye
Click to expand...
Click to collapse
sorry to hijack your thread,
just wanted to ask a short question.
if my info is as below:
US T-mobile MDA Vario
IPL 1.03
SPL 1.06
GSM 01.12.10
OS 1.3.13.5
ROM version: 1.3.13.5 ENU
ROM date: 9/29/05
Radio version: 01.12.10
Protocol version: 4.0.13.23
ExtROM: 1.3.13.116
OS 5.1.70(build 14406.1.1.1)
Click to expand...
Click to collapse
does this mean that its on a G3 chip and that i can use lokiwiz03a to CID unlock it and upload any 2.x ROM as i please? and downgrade the ROMs too?
@Bola: you have a 1.x ROM so you can CID unlock your phone with Lokiwiz0.2b (NOT 0.3a). Then you'll be able to install whichever ROM you like.
Bye
I've just published a tutorial that can help those with a G4 or G3 (>= 2.21) CID-Locked device to install whichever 2.x ROM they like.
The tutorial is here:
http://forum.xda-developers.com/viewtopic.php?t=56088
Bye
risidoro said:
@Bola: you have a 1.x ROM so you can CID unlock your phone with Lokiwiz0.2b (NOT 0.3a). Then you'll be able to install whichever ROM you like.
Bye
Click to expand...
Click to collapse
thanks risidoro.
i'll give it a go later.
there wont be any issue downgrading the ROM later would there?
eg if i were to install:
RUU_Wizard_2211301_22113102_021911_DOP_ASIA_WWE_Ship.exe
Click to expand...
Click to collapse
and later back to
RUU_Prodigy_1060701_101_11310_QTEK_WWE_Ship.exe ?
Click to expand...
Click to collapse
oh, the bootloader (IPL/SPL) doesnt get upgraded either when i upgrade, would it?
oh thank for the help risidoro.
i saw your post after i uploaded mine.
read through your tutorial and i figured that both IPL / SPL will get updated
people like you makes this site great
thanks once again.
ok so i kinda f'ed up my phone..
the specs are
IPL:1.08
SPL:1.08
OS:1.8.11.1
and i decided to flash the radio rom 2.47.11 and now it freezes when i try to enter in my password at start up..i read that what i need to do is get it into bootloader and flash a 2.x rom on it but when i try to pres the reset button and the 2 buttons on the right side it just normally starts up..also how would i upgrade to a 2.x rom..or is there any way to downgrade back to the stock radio rom? also my phone is unlocked
thanks
keith
edit:
could i downlod the RUU_Wizard_225111_22511102_022511_CWS_WWE_Ship.exe rom and flash that onto my phone and have it work...still cant figure out how to get the bootloader screen to come up
yes after doing some more reading i realized i had to hold down the camera button and the start button until the bootloader came up..then i just pluged it in and ran the radio rom of 1.x and it worked yea!! mbe later i will try to upgrade the rom lol
CID unlock it while it is still working with your current ROM
IPL:1.08
SPL:1.08
OS:1.8.11.1
Then stick Molskis G3 ROM on it and you will be sorted.
http://forum.xda-developers.com/showthread.php?t=274316
for more info.
woudl i be able to go to htc.com and upgrade do the rom upgrade there without havin to cid unlock?
Yes, you can upgrade a Cing 8125 with the officially released Rom (as posted on HTC's Website) without CID unlocking your device.
i do not need to upgrade the IPL/SPL first since i have 1.08?
keith1569 said:
i do not need to upgrade the IPL/SPL first since i have 1.08?
Click to expand...
Click to collapse
Official Rom Updates include the IPL/SPL. If you download and flash the Cingular 2.25 Rom you will have IPL/SPL 2.25 after the flash.
is that good or would i want to cid unlock my phone first?
keith1569 said:
is that good or would i want to cid unlock my phone first?
Click to expand...
Click to collapse
Keith,
If you plan to install cooked Roms then you should CID unlock your phone. Technically CID Unlocking voids your warranty (though I had no problems getting warranty exchange on two previous phones that were CID unlocked).
The main reason to CID Unlock is that you can then install most (generally all) Roms that exist for your device. The only exception would be a G4 only Rom (which has the G4 IPL/SPL only) as your phone is a G3.
If you don't CID unlock then you can't install non-cingular Roms that include IPL/SPL so basically you would have to cook your own Rom if T-Mobile released an OS update that you wanted to use.
I would suggest you do some more reading before you CID unlock or flash anything else to your device.
ok bro thanks for the detailed explanation. I will.def do a lot more reading before I flash my phone or cid unlock it..this is a great forum full of useful information
keith1569 said:
yes after doing some more reading i realized i had to hold down the camera button and the start button until the bootloader came up..then i just pluged it in and ran the radio rom of 1.x and it worked yea!! mbe later i will try to upgrade the rom lol
Click to expand...
Click to collapse
Where did you get the radio rom from ????? Do you have a link ????
just type in 2.47 radio rom in a search
keith1569 said:
just type in 2.47 radio rom in a search
Click to expand...
Click to collapse
Ok i'll search for it thought maybe you had a direct link lready ....
is there anyway to "shelltools" flash my radio rom? I've been missing a lot of calls lately and it really is becoming inconvenient. I havent unlocked my phone, but i am running wm6 using shelltools (mfrazzz's stuff) and i was wondering do i even need to have my phone unlocked to flash my radio? i dont want to lose my warranty so thats why this matters to me. Any ideas guys?
You may get the official (in your case, T-Mobile, I guess) ROM to flash your phone with the full set of WM5 ROM (e.g. IPL, SPL, OS and Radio). As you are using the official ROM, you do not have to CID-unlock your phone prior flashing this official ROM. After that, you may then use shelltool to update/upgrade/flash the WM6 in, while the radio is untouched (e.g. still using the one you've flashed with the official ROM).
i thin i have done what you said already. Before i flashed mfrazzz's wm6 rom i flashed the latest tmobile rom, then i proceeded to flash the wm6 rom. I didnt use shelltools to flash the official tmobile rom obviosuly, but i did use shelltools to flash mrazzz's wm6 rom.
these are my things from what i'm using now:
ipl 2.26
spl 2.26
gsm 02.25.11
os 2.18.0.0
Flash the t-mobile uk radio rom 2.19.11.. that'll work for u.
ur OS is wrong if ur running wm6...
2.18 is Crossbow Reloaded... or Faria's..
Madcap180 said:
Flash the t-mobile uk radio rom 2.19.11.. that'll work for u.
Click to expand...
Click to collapse
can i just flash that right now without being unlocked? i'm in boston, does that matter? lol
Madcap180 said:
2.18 is Crossbow Reloaded... or Faria's..
Click to expand...
Click to collapse
oh, my bad then lol.
and yes u can change ur radio without being unlocked
ok thanks guys for all the help, but i still have a couple small questions
first, in this post http://forum.xda-developers.com/showthread.php?t=253609&page=4
(post #34) he says that if you dont cid unlock before applying the radio rom you will brick the phone.
next im looking for that uk rom, but i really cant find it, can anyone point me in the right place? and even though im in the US it will still work right?
thank you guys so much! i really aappreciate it
There you go
jawnsixteen said:
ok thanks guys for all the help, but i still have a couple small questions
first, in this post http://forum.xda-developers.com/showthread.php?t=253609&page=4
(post #34) he says that if you dont cid unlock before applying the radio rom you will brick the phone.
next im looking for that uk rom, but i really cant find it, can anyone point me in the right place? and even though im in the US it will still work right?
thank you guys so much! i really aappreciate it
Click to expand...
Click to collapse
I have flashed my RADIO ONLY several times with no consequences for my CID LOCKED G4 Wizard, here´s the link for the RADIO ONLY
ftp://xda:[email protected]_Thread/T-Mobile-UK_2.19.11_Radio_Only.zip
You have flashed RADIO only on you G4? HOW? I am having the following problem:
I had to flash a T-Mobile German ROM to use the shelltool for the latest WM6 ROM, it worked but unforunately I have got Radio 2.69 and IPL 3.08.XXX1. (from the latest official MDA Vario ROM flash before)
After the Hardreset everything went fine - I've got WM6, but after i had changed the Clock settings and restarted my device i simply have NO SIGNAL anymore. I am currently in australia maybe thats the reason???
I tried to install the offical T-Mobile AKU 2.0, but the RUU shows me error 296 as I have installed a later ROM AKU3.3 bevor my WM6 flash.
Which tools have y used? And how is the procedure?
Cheers!!!
irm
4irm said:
You have flashed RADIO only on you G4? HOW? I am having the following problem:
I had to flash a T-Mobile German ROM to use the shelltool for the latest WM6 ROM, it worked but unforunately I have got Radio 2.69 and IPL 3.08.XXX1. (from the latest official MDA Vario ROM flash before)
After the Hardreset everything went fine - I've got WM6, but after i had changed the Clock settings and restarted my device i simply have NO SIGNAL anymore. I am currently in australia maybe thats the reason???
I tried to install the offical T-Mobile AKU 2.0, but the RUU shows me error 296 as I have installed a later ROM AKU3.3 bevor my WM6 flash.
Which tools have y used? And how is the procedure?
Cheers!!!
irm
Click to expand...
Click to collapse
No, we can´t flash a ROM with bootloader other than the one you have if you have a G4 CID locked device. Unless you use a RUU with no ID (see next paragraph) and the nb.nkf file lacks of IPL/SPL, such is the case of the Wizard Love which I use before to flash any other ROM with the Shell Tool.
Read post #2 of this thread
http://forum.xda-developers.com/showthread.php?t=310954
Read carefully where talks about Splash Screens and Splash Only RUU for G4, same procedure for splash screen applies to RADIO. This doesn´t work for OS, for OS you have to use Shell Tool.
Good luck!