hi
im trying to put spl on my phone kaiser hard spl v1.0 in fact and im having trouble after the dos type screen does its stuff it says the activesync should be grey and the phone should be in bootload mode. then it loads another program to flash it to the device. and this programs needs to have active sync running but the phone is still in bootloader and actice sync is grey what am i doing to myself
bump help me pleaseim stuck and i cant find a slotuion in the relevant spl thread
SOLUTION!
MOD EDIT: SOLUTION:
ok basically i used jockyw2001s spl instead of oilpofs. and remembered to uncheck the allow usb connection in the activsync settings. which olipofs doesnt tell you to do.
ive checked bootloader and this confirms i have spl 1.0
Related
So i just attempted to flash my tilt.
These are the steps i did.
Used Jump SPL 1.56 Kais
Then flashed a Kaiser Custom RUU.exe
everything was good at this point.
I then attempted the Kaiser SUperCID tool
when i did the unlock radio is when the problem occurred. After initializing and completing the screen turned black and does not display anything after the 3g sreen. I have done several soft resets and am attempting to do a hard reset with the soft keys but all it does is restart the phone....
i am not able to do a hard reset via sys>clear storage since no screen is displayed
this is what my phone does show
the tri color screen is this
kais1*0
spl-3.28.Hard
cpld-8
and it says security unlocked above all of that.
The ATnT screen shows this
R 1.70.Olinex
G 25.65.30.04h
D 1.62.00.00
please help
You need to follow step 0. Too late know. Which includes having an actual "RADIO" ready.
1.70OliNex is not a Radio. Thusly the Device can't load the Phone. Find a Radio and Flash it
Oh And Count this as your Freebie. Next time Search for your answer. And if you don't find the answer this should have been posted in the SuperCID thread.
Thank you kind sir. Off to look for a radio
Ghxoxst said:
Thank you kind sir. Off to look for a radio
Click to expand...
Click to collapse
Before you go off.
Here's something to try. The SIM/CID Unlocker do not work with the stock rom and you should have put hardspl on there.
Setup activesync and make sure that it detects your phone. As long as activesync works, you should be able to flash the stock rom and radio on the phone (even if the display is blank).
1st use jumpspl
then put on hardspl (read and follow the hardspl instructions)
then upgrade to 6.1 ROM
Then Unlock
then reflash with the rom of your choice with the matching radio
you should be good to go.
well i finally figured out the hard reset, which i did. It booted up and i was able to do the screen alignment etc, but once i was on my actual home screen it CUSTOMIZED and loaded a bunch of who knows what and back to the blank screen...
well i do have hard spl 3.28. I will try again....Im also not sure if my phone is 6.0 or 6.1
Ghxoxst said:
well i finally figured out the hard reset, which i did. It booted up and i was able to do the screen alignment etc, but once i was on my actual home screen it CUSTOMIZED and loaded a bunch of who knows what and back to the blank screen...
well i do have hard spl 3.28. I will try again....Im also not sure if my phone is 6.0 or 6.1
Click to expand...
Click to collapse
If you have hardspl on there, then just flash one of the cooked roms on the phone. I loaded the L26 Rom and it works great. It will include a radio firmware and is compatible with the SIM/CID unlocker.
the question i have is how do you flash without being able to execute the program from the phone? How am i able to execute it from the active sync?
Ghxoxst said:
the question i have is how do you flash without being able to execute the program from the phone? How am i able to execute it from the active sync?
Click to expand...
Click to collapse
Have you connected it to the computer via usb? Does activesync see the phone? You won't see anything on the phone itself until you correct the problem. As long as the computer activesync sees the phone you should be able to flash it from the computer.
I had the same issue
Just follow the steps
get the SIM unlock code from the computer
then flash a "real radio"
Once it finishes and boots up
it will ask you for the sim unlock code
AND VIOLA!!!
got it going
flashed it from my mini sd card after fat32 formatting it.
works like a charm
Thanks to everyone
Hey guys,
I have two WINgs and I Hard SPLed one already and I Flash it regularly
the other one was at the T-mobile Rom and stable till it starting restarting at every call.
So i treid to Unlock it also like the other one
So I backed up all my contacts and Messeges with PimBackup
and after i Installed the three files
security removal, Aserg and cannonyang
when I try to Hard SPL through RUU with USB so it tells me no connection although its connected in Activsync
I searched the forums and Bypassed the Connection issue by entering the Boot loader through the phone and it got to 2 percent and told me i need a newer RUU although it is the Same as the other Wing for the versions and I have done the other one Fine
when I tried to do it again and still bypassed into the boot loader through the phone it now tells me that There is no Connection to the device. Although the USB sign is available in the bottom.
Now I have Also searched the forums and found Aserg suggesting that we install the Native T-mobile Rom
It connected fine and went into
1% of updating Image and then it gave me a communication Error
Now I noticed two things:
1. it Goes into Bootloader and CHills there
2. It Changed the IPL number from 4.26.0000 to 4.10.0000
but SPL remained 4.26.0002
Does any one have a Solution for this Problem Guys?
Is it bricked now and I just can't see it?
Please help because all my contacts are are on it and i am working with crappy nokia instead of it that has none of them.
you can import your contacts from PIM backup onto your other device if it has PIM also, you know that right?
Now some questions
Did you install the cabs that papamopps said to?
Can you still flash the RUU? It seems you have the newer Wing SPL but the older IPL.
Ok so I was upgrading my radio on my P3600 to 1.41.00.11 to enable GPS and when it started upgrading, the status bar started on the PDA (as per trinityguides.info's instrucions) but it didn't on my computer. My computer then switched itself off, was dead for about 3 seconds, then restarted itself. I pulled the USB cable from the PDA and now it is stuck in a bootloader style screen, but sais,
TRIN100
IPL-0.50
TRIN100 MFG
SPL-1.30.Olipro
A soft reset does nothing, neither a 'Battery pull-out'
I think that I am stuck in Hard SPL (according to Trinity Guides). Can anyone help me get the PDA back to normal so I can re-flash with the new Radio please? Thanks Alot.
P.s If it is of any relevance, My PDA was not synced with Activesync, But before the flash, I downloaded Activesync 4.5 to fix the 'Generic RNID device' problem on XP. It was identified on my pc as 'Mobile device' in my computer, as far as I can remember.
Sorry if this thread is not new to the site but as a noob (lol) im not really 'broken in' to the site yet. Thanks again for your help.
Hi everyone,
After further research, I reckon I should do the following:
1. In hard SPL, Connect it to another XP computer (my laptop)
2. Untick box called 'Enable USB connections' or whatever in Activesync 4.5
3. Open the ROM of my choice and Double click 'upgrade' or whatever
ROM][WWE][30.10.2008]Karmba_a Diamond Blue For Trinity
4. Wait for the ROM to install
5. Let the trinity soft-reset
6. Done!
7. Upgrade to radio '1.41.00.11' off trinityguides
8. Wait for the radio to install
9. Done!
Please tell me if im wrong so I know if there are any other steps to take. Thanks alot.
Ok guys, I guess, with time I solved my own problem. I did in the end connect my PDA to my XP laptop and used 'splxploit' (thanks to whoever made/programmed this!) which unbricked my device. Now when I tried to upgrade my radio again to a different version, because I have Olipro 1.30 installed instead of 1.20, I was unsuccessful. This shall be what I do next so I guess this thread is not needed anymore.
I'd appreciate it if one of the mod's would close this thread to try and save precious server memory, or can I do it myself (soz im new(ish) to the site!)?
Cheers Guys.
Hey everyone,
recently the screen of my HTC Diamond died. I have since reflashed to the original ROM and am currently attempting to reflash to the original SPL. However, when I load the RUU with the correct .NBH I want to flash to, the progress bar stays at 0%. After this, it gives me an error 202 meaning the USB cannot connect to the phone. However, ActiveSync is connected, and MyMobiler is trying to find my phone all the time, yet not finding it. Any help?
Doh the tag lifts. Please delete
Have you tried putting the SSPL-Manual.exe file in \Windows\Startup of your device so it will be launched at startup? Maybe this will set up the device in mode that RUU accepts.
i tried to flash my xperia,and now i'm stuck.last time i flashed it without any problems.i've got touch flo on it ,and now i want something different.the problem is when i enter the hardspl the tricolor screen starts and then the white screen comes with loading..then i get the message connection error and i'm stuck on the loading screen...i've already tried hard reset....someone please help...
According to russell eclair blog and guide, your problem as you described is caused that you don't connect your X1 to Active Sync.
As it described, in HardSPL case is different to flashing ROM. So you have to connect your X1 to computer through Active Sync (unselect high speed @USB to PC) then you may run the hardSPL.
I have never had such problem so what I can tell is what I read on the russell eclair blog. If you need more information go to his blog (search it from google is allright). I hope it's helpful.