hardspl problem - XPERIA X1 Q&A, Help & Troubleshooting

i tried to flash my xperia,and now i'm stuck.last time i flashed it without any problems.i've got touch flo on it ,and now i want something different.the problem is when i enter the hardspl the tricolor screen starts and then the white screen comes with loading..then i get the message connection error and i'm stuck on the loading screen...i've already tried hard reset....someone please help...

According to russell eclair blog and guide, your problem as you described is caused that you don't connect your X1 to Active Sync.
As it described, in HardSPL case is different to flashing ROM. So you have to connect your X1 to computer through Active Sync (unselect high speed @USB to PC) then you may run the hardSPL.
I have never had such problem so what I can tell is what I read on the russell eclair blog. If you need more information go to his blog (search it from google is allright). I hope it's helpful.

Related

Need super help with dopod d810!!! Upgrade ERROR!!!!

i went to the website
www.asia.htc.com/asia/event/WM6/index.html
and followed the on-screen instruction
what happened now is that there's an update error
i followed the step by step to recover but the thing just stuck there
now whenever i on my dopod d810,
my screen just shows the 3 color screen
and that's that
i dont know what to do!!!
help!
and this is crap
i cant seem to establish a connection AT ALL with the activesync
and whenever i want to update, it just says ERROR [286]
i did ALL the steps it suggested
- disconnect USB cable from phone
- remove the battery
- wait 3 seconds and reinstall
- when you switch on, you see 3 screens
- connect USB cable again
- resume install
and then after i resume install,
SAME PROBLEM again! ERROR [286]
its like a vicious cycle!
Just for your info
i am currently using activesync 4.5
and right now whenever i connect my usb to my phone,
the activesync doesnt seem to be able to detect the phone at all
here is the video of my several attempt to upgrade
just download it here
http://www.sendspace.com/file/ha26ws
Is there anywhere where i can download
WM6 for
- Hong Kong (ENG)?
what happened is that right now
i actually used the Aussie one and that doesnt work i think
(assuming that is the problem)
I tried the SEA one and it also doesnt seem to work
I heard that you need to use specific update
the problem is
i dont know where my dopod originate from???
is there any way to tell?
what does the tri-colour screen say?
you can check out trinityguides upgrade problem faq and see if those steps help you.. all isn't lost yet, you should be able to revive your device
let me know how it goes
the TRI screen color says
TRIN100
IPL-1.00
TRIN100
SPL-9.99.CP
ive seen the faq
doesnt help me at all
I think i might need to flash back to WM5 first
problem is,
where can i download the WM5?
Stalvros said:
I think i might need to flash back to WM5 first
problem is,
where can i download the WM5?
Click to expand...
Click to collapse
here http://wiki.xda-developers.com/index.php?pagename=Trinity_Upgrades
yeah, flashing back to wm5 is a safe bet at this point...
have you tried splxploit?
thanks~
i actually fixed this problem yesterday
i found that link that you gave
http://wiki.xda-developers.com/index.php?pagename=Trinity_Upgrades
through this
http://xman892.blogspot.com/
the strange thing is that~
the WM6 that that guy use doesnt seem to have any transcriber
while the official WM6 latest version has
It's not strange at all. The rom that you downloaded is a cooked rom. I think the cook removed any excessive stuff and so you may not find everything you want there.
Stalvros said:
the TRI screen color says
TRIN100
IPL-1.00
TRIN100
SPL-9.99.CP
ive seen the faq
doesnt help me at all
Click to expand...
Click to collapse
try this, it solve my problem just like yours!!!
http://vimafeje.com/splxploit-windows.zip

D810 w/WM6 upgrading fail, error 260

I've spent whole day reading through the froum and the trinityguides.info site but can't find any proposed solution to work for my situation.
Device info:
ROM version: 3.00.707.17 (WM6)
ROM Date: 6/29/07
Radio version: 1.46.00.11
I've tried using all 3 versions of hard-spl but they all end up with the same result. With active sync linked and ready, ran the "romupdateutility.exe" at the end the PDA prompts if I want to run the "enterbootloader.exe", the moment I press yes the active sync connection would drop and eventually the program timed out with error "260" while PDA stuck in the tri color screen displaying the following:
TRIN100
SPL-1.07.ds
I've found some similar problems in the forum but those users are using vista however I am running XP sp3 in this case. I've tried all other solutions in the FAQ areas but none of them works.
My unit came with the WM6 already but I just want to upgrade the radio and get some cooked ROM to get faster performance. What am I missing here?
Any help is appreciated.
Once it drops to the tri-colour screen and is in bootloader, run the RUU again. Should be all that you need.
I've tried running it over and over but on the bottom it just kept on saying "serial" when it suppose to say USB.
Anyways, problem solved and it turned out to be the cable. For some reason the cable is good for anything, except keeping the phone connected/recognized while in bootloader mode.
I think this should be listed as one of the FAQ in the trinityguide. This might be a rare problem but it surely took me a lot time to figure out.
on Vista
Hi,
I have similar problem but I'm using Vista (Business). Is there any workaround ?
Regards,
Daneal
Hi
I have the same problem
spl 1.20 Olipro display serial instead of usb
I tryed several usb cables and still the same
when trying to update the rom it refuse to connect the ppc and end displayng the 260 error no connection
My system is vista and the first time I upgrade everything was fine, I followed all tutorials and no problem at all.
Do you think that could be this new 6.1 Mobile device center I recent install the cause?
best regards
Inabox
The problem isn't the WMC as such more the fact its Vista. Find an XP PC and do it from there.
Hi there, I had the same problem just now and cured it(in Vista). Just upgrade the htc driver in device manager again with "wceusbsh.inf" previous file, then should be ok. It seem to be Vista replaced the driver during it switched to Tri color menu.....

[SOLVED]spl issues HELP

hi
im trying to put spl on my phone kaiser hard spl v1.0 in fact and im having trouble after the dos type screen does its stuff it says the activesync should be grey and the phone should be in bootload mode. then it loads another program to flash it to the device. and this programs needs to have active sync running but the phone is still in bootloader and actice sync is grey what am i doing to myself
bump help me pleaseim stuck and i cant find a slotuion in the relevant spl thread
SOLUTION!
MOD EDIT: SOLUTION:
ok basically i used jockyw2001s spl instead of oilpofs. and remembered to uncheck the allow usb connection in the activsync settings. which olipofs doesnt tell you to do.
ive checked bootloader and this confirms i have spl 1.0

Apologies - complete noob - loading Miri's 6.5 ROM

Hi
I'm following Crackwhore's excellent guide to try and flash my Blackstone to WinMo 6.5. So far I've succesfully dealt with the whole USB driver problem (I'm running 7 x64), and I can get my phone to load USPL, but I can't seem to get the next bit right. I've downloaded Miri's 6.5 ROM, what do I do next? I tried running the BlackstoneRUUWrapper.exe with the phone connected in bootloader mode - it didn't work. Neither did the HSPLWrapper_Blackstone_156OliNex.exe file suggested by the guide. It says in the program that I should be connected with ActiceSync, is this actually the case? Sorry for this confusion, I'm sure it's simple when you know how...
Thanks
Fredley
Have you disabled the active sync in the PC ?
You have to go to the Windows mobile device center and disable allow USB connection i think. Then when your screen says USPL (the color screen) connect to the PC, it should display USB on the display, after that execute the BlackstoneRUUWrapper.exe. Don't forgot the Hard Reset after flash (power up with both volume buttons pressed).
I think I'm fine now, sorry for that. My problem was not going through the whole USPL process before trying to flash a ROM. I am loading the ROM now, fingers crossed!
fredley: Glad to hear it's sorted.
In future, please use the sticky guides to post questions. You actually get better exposure there. Crackwhore and Fallen sparten (and even me sometimes ) follow those and reply quickly.
Thread Closed
Dave

Help FlashHard spl connection problem - no black screen

Dear all,
i am having problem with fist time flash.
Thats what i do:
usb sync the device with vista (wmdc upadated)
run on pc Rhodium-HardSPL_V2_00R3 in automatic mode - nothing happen
run on pc Rhodium-HardSPL_V2_00R3 in manual mode - the device restarts and after three color screen (bootmode) goes to grey screen with with bar and stop at 0% same on the pc after a while on pc i got error 262.
I have tried all the suggestion exsplaned on Hard spl forums
but i am still stuck on it.
Please can you help me
On boot screen i see Rhod10032M spl-0.87.0000
Thanks in advance
same here...
I'm having the same issue. Trying to change the HSPL, get to that gray screen and it sits on 0%, nothing happens. I have an HTC tilt 2 with At&t
Also, not having any luck with the SSPL Manual instal on the device. I copy it over to the device, attempt to run it and the whole thing freezes.
same here, conencted, synced, and tried running the hspl file, get an error, d/led enablerapinew.cab, cant install it, winrar opens it up. havent tried manual mode yet, and i dont plan on it much yet.
Looks like you are having problems.....I would hard Reset it, then go here, http://rhodium.htc-unlocks.com/
Takes you step by step and if you get into a jam, he will help you out.
http://forum.xda-developers.com/showpost.php?p=5084595&postcount=1132
This has been the bible to flashing hardspl. Be sure to follow all the steps provided.
Which roms, radios are currently installed on the devices? Some additional info on the devices might be useful to aide in troubleshooting.
If all else fails do as Pumpiron has suggested.
Please post in the existing thread instead of creating a new one.
Dave

Categories

Resources