Hello..
I've got a sirious problem... I can't tocuh in my password in the startup of the diamond. I've reseted it and still it's not working
I have Duttys Diamond WWE_5.2.20273_Rom Release V1.5. Anyone that have the same problem or that can help me out? Would be greatful.
Perhaps your phone is locked. Had the same problem - phone was locked and i coudn't do any input on touchscreen.
Try to soft reset your phone. Then after boot - short before you have to input your pin you will see "unlock" in the bottom left corner of the screen. But this message will only appear for a very short time.
Related
Has anyone come across the problem of a TILT hanging up (could not find common denominator when does this occur) and ONLY the "Start" icon (and the "start" button)is inoperable. i.e. all functions work perfectly, however I have no way of getting to the Start screen - only soft reset. Help anyone
Do you have a password set? Does this only happen after a call? If so, this has been discussed many times - just do a quick search.
If not, I´m afraid I can´t help you with your issue.
Good luck!
djmaven said:
Has anyone come across the problem of a TILT hanging up (could not find common denominator when does this occur) and ONLY the "Start" icon (and the "start" button)is inoperable. i.e. all functions work perfectly, however I have no way of getting to the Start screen - only soft reset. Help anyone
Click to expand...
Click to collapse
I think I had this problem also. I'm not sure what causes it, but it looks like ti appears after I try to use MS Voice Command.
I had this problem. I found it doesn't need a soft reset, just switch it off (hit the power button briefly) and back on again. Fixed it every time. Annoying but not fatal...
I am having a similar problem. I recieved an 8925 with a touch screen that doesn't work. No physical damage, but I noticed there is no start screen. I got it to upgrade to WM 6.1but still no start menu or system settings. It boots to the align screen but of course the touch screen doesn't work so that's all I get. Sometimes I get past that and the rest of the PDA seems to work with the keypad. I have reset it several times and still nothing. I removed the touchscreen and ordered a new one. Hope I haven't spent folishly. If someone has a clue to what the problem is I would be very grateful.
Hi there
I've not had this problem before
I had to reset my Kaiser because it froze while trying to do too many thingsd at once.
And it rebooted to the pin screen, I put my pin in and waited, and waited, and yet nothing.
I've had the pin lockout bug before and its not that, none of the top bar information is displayed, in fact the only thing showing is my signal bar with a little X next to it.
i managed to boot into safe mode with pocket plus with no worries, but with any standard soft reset I can get past the pin screen.
So I took the plunge and Hard reset expaecting to have this fixed. But im still stuck at pin screen, with no siganl showing.
Anyone any idea what the bloody hells going on?
Im on Dutty's latest dual rom. but i dont think its to blame...
help...cheers in advance
I'm stuck at the "Tap the screen to set up your Windows Mobile-based device." The screen on my HTC 8125 has been acting flakey... working sometimes, but mostly not. A friend thought he would help out, and thought hard reseting the device might help. Now I'm stuck at the tap this screen message, only the touch screen isn't working and is not accepting the tapping. Am I completely outta luck without a phone now?? At least before I could make and answer phone calls. Now, NOTHING. Just this screen. IF there is any way around this that anyone knows of, PLEASE let me know!!
Thank you
I think you have a hardware problem
Maybe the flex
maybe the microcontroler
maybe the rom Try a new again instead the one you have
for skip this screen alignment try to search on the forum there are many ways
I simply conect it to activesync even if it is stucked at this screen it syncs with your pc via activesync... then go to explore...Windows folder.... startup... and delete the file called welcome.lnk then softreset.
Yeah my wizard is stuck to @ tab the screen etc.
I can't connect to activesync becuase activesync does not detect the phone.
Nevermind!
tnt929 said:
I'm stuck at the "Tap the screen to set up your Windows Mobile-based device." The screen on my HTC 8125 has been acting flakey... working sometimes, but mostly not. A friend thought he would help out, and thought hard reseting the device might help. Now I'm stuck at the tap this screen message, only the touch screen isn't working and is not accepting the tapping. Am I completely outta luck without a phone now?? At least before I could make and answer phone calls. Now, NOTHING. Just this screen. IF there is any way around this that anyone knows of, PLEASE let me know!!
Thank you
Click to expand...
Click to collapse
Try to replace a new battery, i have the same problem be4. And i discovered the battery is bulked. So I go to buy a new one, and problem is gone now.
still stuck
I have the same problem, i tried looking through explorer but i couldnt find the file to delete so that i could bypass this startup. If anyone figured anything out let me know please.
[email protected]
thanks!
1. Do a soft reset. (small hole on the right side)
2. When screen is black hold camera button, this will boot into bootloader
3. Connect USB cable (USB will show over left softkey)
4. Try to flash a new ROM.
I did this process a few times with different roms.. the best I had was using the HardSPL process, and then the NBD_v8.3_8MB rom.
Hi all!
This is a brilliant forum, and I am reading it with a lot of plessure
I have a HTC TyTN II, and my touch screen does not work.
This was not a problem until I updated to WM 6.1..
Now I cant use the TyTN because it says "Tap the screen to set up your windows based device"
Is there a workaround for this?? Or do I need to send it in for repair?
Thanks!
Stupid me!!!!
It was due to the stupid screen protector and stupid me!!!!
You're not stupid, fella.
Just "differently clever".
this is what emotions you just went through ................. and now you think you are a Homer Simpson look alike......LOL
Hi folks!
I had the same problem: change my at&t tilt rom/radio/spl to htc.
result: touch screen does not working!
The only way that i found is undo changes:
1º - installing and using: Remote screen Alignment to skip the first screen calibration. Just power on Tilt and wait until activesync are connected, so, run "remote screen alignment" and click skip, if the phone does not restart, do a soft reset.
2º - In the next power on, use activesync to copy JumpSPL1.56-KAIS.exe to your phone.
3º - use the buttons to navigate and execute JumpSPL1.56-KAIS.exe on the phone. (to execute JumpSPL1.56-KAIS.exe file use the ENTER key of the sliding keyboard).
4º- now just replace RUU_Kaiser_CINGULAR_WWE_.exe (OEM ROM i think)/ bootloader spl1.93.0/1.56 (maybe the screen problem occurs due the wrong spl/rom combination or newer spl like 3.28/3.29 ).
After these steps my AT&T Tilt touch screen is back to work!
Now i'm ready to try others roms again !!
PS: Sorry for poor english, if anybody don't understand anything just ask!
Few hours ago i unlock my phone, there was a problem with radio rom, and my friend recommend to install Kaiser HyperDragon III_WWE version of WM6.1.
I install it, play 5-6 minutes and after this check some delay problem. I make soft restart and after this phone touch screen don't work.
Touch don't response. Made hard restart ... and it's the last think that i did.
At startup i check this "tap the screen to setup your windows devices ....", but as touch screen don't response .. i don't have any progress.
Try to resintall the same WIN6.1 version, but no changes.
Any advice? what's the problem.
Is there any way to fix it ?
sounds like a hardware problem. Most likely the wiring is bad or corroded. You'll need a new screen or you might be able to fix the wiring. I kind've don't like the fact that our kaisers vibrate at startup because you think it would eventually rattle something loose which may have happened in your case. Before getting a new screen though, load a new ROM. To do it without activesync enter the bootloader mode by pressing down the camera and power button at the same time while the phone is off. Then connect your phone and it should say USB after a few minutes. Then flash
http://forum.xda-developers.com/showthread.php?t=485288
Please Read This Thread...
Because I had almost same problem like your's...
Try the install HardSPL...