Stuck at boot screen - 8125, K-JAM, P4300, MDA Vario Software Upgrading

I'm stuck at the "Tap the screen to set up your Windows Mobile-based device." The screen on my HTC 8125 has been acting flakey... working sometimes, but mostly not. A friend thought he would help out, and thought hard reseting the device might help. Now I'm stuck at the tap this screen message, only the touch screen isn't working and is not accepting the tapping. Am I completely outta luck without a phone now?? At least before I could make and answer phone calls. Now, NOTHING. Just this screen. IF there is any way around this that anyone knows of, PLEASE let me know!!
Thank you

I think you have a hardware problem
Maybe the flex
maybe the microcontroler
maybe the rom Try a new again instead the one you have
for skip this screen alignment try to search on the forum there are many ways
I simply conect it to activesync even if it is stucked at this screen it syncs with your pc via activesync... then go to explore...Windows folder.... startup... and delete the file called welcome.lnk then softreset.

Yeah my wizard is stuck to @ tab the screen etc.
I can't connect to activesync becuase activesync does not detect the phone.
Nevermind!

tnt929 said:
I'm stuck at the "Tap the screen to set up your Windows Mobile-based device." The screen on my HTC 8125 has been acting flakey... working sometimes, but mostly not. A friend thought he would help out, and thought hard reseting the device might help. Now I'm stuck at the tap this screen message, only the touch screen isn't working and is not accepting the tapping. Am I completely outta luck without a phone now?? At least before I could make and answer phone calls. Now, NOTHING. Just this screen. IF there is any way around this that anyone knows of, PLEASE let me know!!
Thank you
Click to expand...
Click to collapse
Try to replace a new battery, i have the same problem be4. And i discovered the battery is bulked. So I go to buy a new one, and problem is gone now.

still stuck
I have the same problem, i tried looking through explorer but i couldnt find the file to delete so that i could bypass this startup. If anyone figured anything out let me know please.
[email protected]
thanks!

1. Do a soft reset. (small hole on the right side)
2. When screen is black hold camera button, this will boot into bootloader
3. Connect USB cable (USB will show over left softkey)
4. Try to flash a new ROM.
I did this process a few times with different roms.. the best I had was using the HardSPL process, and then the NBD_v8.3_8MB rom.

Related

Please Help!!!! Tilt Dead!!!!

Hello guys. I have been searching the forum for over an hour to figure out a way to get my Tilt back up and running to the way it was before. I had almost every updated cab thats out there on my tilt along with the TomTom 6 software which is where the prtoblem occured. Once I installed a cab file called "MN6-update" to my memory card it soft resetted itslef and now all I get is a blank screen. This file was supposed to help redirect the maps that I downloaded for tt6 so the program will be able to read it. After installing this file all my phone does now is load up the AT&T startup animation and then it blanks itself out.
I downloaded mtty 1.42 and am able to see the boot screen and it says usb when I connect it. What do I do next? Any help will be much appreciated.
Does anything on the screen show if you do a hard reset?
When I reset the device I only get the At&t welcome screen (along with the anoyying sound) then.... Death. The screen blanks out and none of the buttons respond.
Update: I just did another reset (By holding the power button for 30 seconds) and a message appeared telling me that a reset is not possible due to a program that was installed from an unrecognizable source. It said that it will automatically restore the phones factory settings and since then it has been stuck on the At&t screen for several minutes. Does this change anything?
The Factory Defaults loaded automatically
Looks like that second reset did the trick. Now all I have to do is load all those cabs again avoiding that last problematic one of course!

Help me unbrick my ATT 8925

Hi,
I tried to unlock my ATT 8925 and looks like I screwed it royally Now the tri band color also dont apear! It is all black screen. If I press camera button and then do a soft boot (reset) then I can see the power light. Please help!
if you go the wiki page for this device it might help you out, or try searching google
shuman said:
Hi,
I tried to unlock my ATT 8925 and looks like I screwed it royally Now the tri band color also dont apear! It is all black screen. If I press camera button and then do a soft boot (reset) then I can see the power light. Please help!
Click to expand...
Click to collapse
try contacting GSLEON or Jockyw2001
Go here http://forum.xda-developers.com/showthread.php?t=393337 , download attached files and start from step 4
what kind rom are you using if its 6.0 then theres the problem flash to a 6.1 rom
How do I fix the rom 6.1? It is total dead seemz, not even power light! any help is much appreciated.
Did you try bootloader mode? Power+Camera+Soft reset button?
Kraize
I dont belive I tried the boot loader mode. I'll do that, however, what should I see if go into bootloader mode? what is the next step. Thanks everyone for their help, much appreciated.
No luck, I tried bootloader mode, same thing, all i get green power light and black screen!
your phone is in oemsbl, you erased everything. if you follow what i said in my previous post(#4) you can fix it.
Hey,
any help with a Tri-colour screen problem?
other thing is, i can't tell where to read your reply from
Jerry
Hey,
can anyone help me with AT&T 8925 Tri-colour screen problem?
msn please @ [email protected] because I have no idea how to read the reply to this post, I'm new to all this..
It froze one day, soft reset and it came back in tri-screen. I plugged it into the charger and it worked..
Did that a few times now it won't do anything and it is stuck in tri-colour with:
KAIS1*0
SPL-1.93.000
CPLD-8
i didn't instal anything, it just locked up and not nothing I do, soft or hard reset will make it come back.
I also wanted to install an Australian OS to Telstra maybe, but not sure which ROM or RUU to download.
Can anyone help please, this is extremly important... and donations will be paid on completion of problem.
Thanks
jasonrush said:
your phone is in oemsbl, you erased everything. if you follow what i said in my previous post(#4) you can fix it.
Click to expand...
Click to collapse
what if set can't conect with mtty and no conectivity with the pc and only green lights on the set?????
i have an att tilt and i was trying to unlock it and it got bricked. it will cut on and everything but it doesnt make the swoosh sound when it gets to the white att 3g screen. after that screen it goes completely black and i cant do anything. iv tried the soft reset and it works perfectly fine, the touch screen and everything works great and it goes to the try screen but when ever i try to connect it it doesnt say usb, it says serial. i need any help you can give me its just been sitting here for about three month and i need to unlock it.
please help.
montreezy said:
i have an att tilt and i was trying to unlock it and it got bricked. it will cut on and everything but it doesnt make the swoosh sound when it gets to the white att 3g screen. after that screen it goes completely black and i cant do anything. iv tried the soft reset and it works perfectly fine, the touch screen and everything works great and it goes to the try screen but when ever i try to connect it it doesnt say usb, it says serial. i need any help you can give me its just been sitting here for about three month and i need to unlock it.
please help.
Click to expand...
Click to collapse
Try following all these steps.
http://forum.xda-developers.com/showthread.php?t=433835

Diamond cannot startup past windows screen

Hi
I was trying out some of the samsung today plugins when my device froze(if i touched the screen or the hardware buttons it would still make a noise). I reset my diamond, it started up I then put my password in clicked unlock and now my diamond wont boot past the windows green splash screen. If I push the power button off then on again I end up in the same situation as before(if i touched the screen or the hardware buttons it would still make a noise and the wheel would light up).
Can someone please help me to fix this problem. I hope there is another way than a hard reset as I would not like to lose my programs and data on the 4gb memory.
Thank You
Can anyone help?
just found something else. when my diamond wont go any further and I plug it into my pc it comes up as mass storage. Ive tried pressing the touch screen to try get it into active sync but it will not work. I also discovered if i hold down the power button to turn the diamond off the warning box comes up. This is getting very weird. Is there a way to make the phone go into active sync mode?
From previous experience if it won't go past the boot screen and a soft reset hasn't helped it will be a hard reset. The good news is that all information on the internal storage drive will be safe and not removed.
Good Luck

Kaiser touch screen problem

Few hours ago i unlock my phone, there was a problem with radio rom, and my friend recommend to install Kaiser HyperDragon III_WWE version of WM6.1.
I install it, play 5-6 minutes and after this check some delay problem. I make soft restart and after this phone touch screen don't work.
Touch don't response. Made hard restart ... and it's the last think that i did.
At startup i check this "tap the screen to setup your windows devices ....", but as touch screen don't response .. i don't have any progress.
Try to resintall the same WIN6.1 version, but no changes.
Any advice? what's the problem.
Is there any way to fix it ?
sounds like a hardware problem. Most likely the wiring is bad or corroded. You'll need a new screen or you might be able to fix the wiring. I kind've don't like the fact that our kaisers vibrate at startup because you think it would eventually rattle something loose which may have happened in your case. Before getting a new screen though, load a new ROM. To do it without activesync enter the bootloader mode by pressing down the camera and power button at the same time while the phone is off. Then connect your phone and it should say USB after a few minutes. Then flash
http://forum.xda-developers.com/showthread.php?t=485288
Please Read This Thread...
Because I had almost same problem like your's...
Try the install HardSPL...

Blackstone bricks!! Please help!!!!

Hello guy,
After flashing new rom (official release) on my Blackstone, works fine for a month, after start the home screen being black like the phone is off but he was not. I try first hard reset from the button located next to the sim card, splash screen appears after went black again. I did not realized is a problem with the screen and I perform a hard reset (volume up+down & power up) . The phone perform the hard reset because I heard the power up sound, plus for about one minute I have the screen on, asking me to make the screen line up. During the screen line up the screen went black again and no way to see it showing something again. The problem is in active sync the phone is not recognized anymore, I can't flash it again (I try run RUU but give a error message to connect the phone) plus I'm going blind without seeing anything on the screen. My question is there is any way to solve this problem.
Thank you in advance.
Although screen is black, you should still be able to get into bootloader by normal procedure (turn off device, hold vol down & then press power on). Once in bootloader try flashing (you may wanna try returning phone to stock rom as it sounds like your screen has become loose from motherboard and needs fixed under warranty).
To return to stock rom follow guidelines at bottom of first post in this thread.
Still not working
Thank you for the quick reply, I manage to flash it again with the original rom, but nothing happen, the screen is still black. Probably as you said is something wrong with the display. Another problem is I don't have any more warranty; maybe there is a solution to solve the problem?
The Blackstone is out for less than one Year. Your should really have warranty. oO
Yes you wright but I’m 10000 km from home where who knows where the receipt is. Still hopping there is a solution, maybe I can fix it somehow. By the time I get home the waranty is gone. Thanks.
open it up, and attach the ribbon cable back in, just take your time if you need the htc touch hd service manual, i have it. if you wish to use it let me know i will post it here.
That is going to be a big help because I never open up a phone, I watch couple of times some videos on you tube but that’s all about. Anyway I have to open it because I flash it with 3 different roms and still the screen is black. Even when flashing does not showing anything on the screen. I remember for my old blackjack I had a app called My Mobile to see the screen on your desktop I install that I so the splash screen , the align the screen but I couldn’t go more taping the screen of the phone by looking to the desktop.
Thank you for your help and I waiting for the service manual.
Thanks’ one more time.
You can get the service manual here: http://htcdriver.com/index.php?page=htc-blackstone-touch-hd-service-manual
Start downloading. Thank you
Keep us up-to-date on your progress so we can aid & assist if possible
Ta
Rick
Fallen Spartan said:
Keep us up-to-date on your progress so we can aid & assist if possible
Ta
Rick
Click to expand...
Click to collapse
Thank you,
First I have to find a place where I can buy the tools, probably in couple of days I let you know about the evolution of the HTC operation.
You dont have the possibility to contact youre retailer and require a copy of the receipt?
Since the phone got an IMEI number, you could probably just send them the phone and they'll see that you still have warranty on it.
I'd call them before sending the phone, also.. don't forget to restore the spl etc..

Categories

Resources