I've been using my HTC Diamond for about 2 weeks now.
Bought it from www.plemix.com and it came unlocked , and I had no trouble at all using it and installing the HardSPL's / updating ROM (Dutty's Diamond v1.6) .
Today I ran the TomTom Navigator 7, and after a while it started to make continuous sound - the default sound when a button is pressed or touchscreen is tapped- , so I did soft reset a few times, didn't solve it, touchscreen was kinda jammed, and I took out the battery. A minute after I put it back, and it worked fine, I took some photos right after, and everything was working fine.
Then two hours later, I took out my phone from pocket to check the time, I see it's halted on the photo screen, and no response at all. So I just turned the phone off by taking out the battery, and just left it off until I came home.
Now the touchscreen is not responding to any taps or clicks, except that it seems that it still detects any sort of tap/click, because the backlight comes on from dim state when I try to tap it.
So it definitely means the touchscreen is not completely dead, but it's just not functional most part.
Hardware buttons works fine, but I'm stuck at the initial "Tap your screen to begin configuring your Windows Mobile" after hard reset. I even updated the ROM to Dutty's Diamond v1.8 just now.
Since I can't do anything and just leave it idle, it goes to [ Align Screen ] page, and still I can't press any cross, since the touchscreen is completely not responding.
Anyone had this screen death problem? Any method of solving it?
---Updated---
Just now the touchscreen worked for 30 seconds, i could actually align the screen, then it showed me the Date/Time setting page, where I could scroll the cities , but then it stopped working again. So i'm still at Date/Screen page...
--Updated--
The touchscreen works for 2 minutes after I do a soft reset / power on&off, or I should say, it works until you press some hardware key on the bottom (volume up/down buttons doesnt affect this).
After I press any of those buttons at the bottom, the touchscreen stops working.
Also, after I turn on the device, enters WM, and runs TouchFLO3D, for the entire time touchscreen works, it's constantly pressing the tasklist dropdown (upper right corner of the screen), making it constantly pop down the task list.
have you tried a hard reset?
Yes, like 3 times. Wiped everything, OS, ROM, NANDFlash.
Also updated the ROM from 1.6 to Dutty's 1.8 ROM. Everythingn works fine except for the Touchscreen.
Right now, when I turn on, the touch screen seems to be pressing all the time at the task manager part of the screen (where the [X] is), its popping up all the time the task list, then after a while, like say, 2 minutes, touchscreen again ceases to work.
Not really promising, but you could try to remove the screen-protector. Perhaps this releases any tension onto the screen.
Thanks. I've thought of that, maybe I'll try later on.
For now i'm suspecting that maybe water went in through, so I've put the phone upside down to maybe take out the water using gravity for 2 days.
It seems like it's working better now, with longer hours of normal functioning..
I'll wait and see one more night... if water is the cause of the problem, it should dry up in say 3-4 days.
It may sound strange, but pit it face down on the carpet and rub it around for a while. Its how I fixed mine. Don't ask me why it works but I had the same thing happen. I think somehow the electrical charge got dissipated from the screen and the static from the carpet recharged it.
Actually your words makes a lot of sense
My Diamond was acting completely alright today, used GPS for 2 hours and called a few people along with many weather updates.
Seems to be working fine now...
But I think what you said is pretty reasonable, since when I rubbed my dead screen , after a few rubs it started to work (2 days ago).
Thanks
yeah this had happened to me about a week ago exactly the same thing I had hardspl mine and updated radio to .05 and then a few days after I had the identical problem. However I took a shortcut and sent the phone back in and requested a replacement claiming it was defective they agreeded and sent a new one however this one already has .05 radio on it so I didn't have to hardspl it. I can't say any of these things would have worked form me as I did not try them byt symptoms are identical. my .02
Related
It have happened to me 3 times already, and I've only had my Diamond for 3 weeks...
When I leave my device charging over night, in the morning the display looks completely scrambled / distorted and the only thing I can do is a restart... Luckily it boots up normal again.
Am I the only one with this issue??
Btw... I've handled my phone with care & not ever dropped it or had it near any moisture, I guess this might be a harware issue!?
Dun worry owziee....
I having the same problem too.........
nothing but a white static/scrambled screen, right? Happens many time to me...the only thing i can do is re-insert the battery (holding the power button to restart doesnt work).
what about soft reset button ?
Sof reset fixes it. I think that the 3D chip is overheated, because it happens when I play sensory overload (a 3d game) too.
But strangely not when I play Call of Duty 2...?
Alteast we could get it back to normal with a soft-reset, kaiser had similar problem where only a hard-reset was possible after the same situations i guess..
Regards,
Carty..
i had a similar situation after i used my device to send a text, turned the screen off then turned it back on immediately, i had some strange screen with all different coloured pixels and it looked broke as hell, but i merely just pressed the power button on and off and it was fixed again :S
Yes i have the same problem and have no idea what is causing it. The most frustrating thing is when it happens my alarm does not go of... I would realy like a fix for this.
phew! It has happened once with me, and frankly it scared me a bit. Removed the battery and then it was Ok again. Weird behaviour. I don't think it has anything to do with heat tho.
I had the same issue too and I had to perform a soft reset fer it to work but after a week the touch screen of mine stopped workin no idea why i had to give to the service center fer repairs they told me it wud take a week to repair it rite now I am without a diamond
Something like the screen shots below?
I've had this problem for quite a while. If you disable Touchflo3d, you will not have this problem at all. This issue only concerns the 3d gpu.
I've since updated to v1.93 Olinex SPL and its more stable now, thou I still get it once a while, especially after a long period of not touching the phone (e.g. when sleeping).
OK, so I tried taking my Kaiser out of my pocket and it slipped sending the phone, the back cover and the battery in three different directions. I put it back together but it wouldn't switch on. The green light would blink when pressing the power button but nothing more than that.
I checked everything again including the battery contacts which seemed OK, but the contact pins UNDER the battery seemed a bit flat so I repositioned them. I tried again with fingers crossed and thankfully it came back to life.
Everything seems to be working fine except one little thing I noticed. When I bring the phone out of power saving mode, the clock does not update automatically. It just displays the time the screen went black. One touch with the stylus anywhere on the screen will update the clock. To me this seems like a software problem so I am thinking of reflashing but since this issue started after the fall I am also afraid of an underlying hardware problem that could cause unexpected behavior during the flashing process.
Any suggestions or ideas?
jt131 said:
OK, so I tried taking my Kaiser out of my pocket and it slipped sending the phone, the back cover and the battery in three different directions. I put it back together but it wouldn't switch on. The green light would blink when pressing the power button but nothing more than that.
I checked everything again including the battery contacts which seemed OK, but the contact pins UNDER the battery seemed a bit flat so I repositioned them. I tried again with fingers crossed and thankfully it came back to life.
Everything seems to be working fine except one little thing I noticed. When I bring the phone out of power saving mode, the clock does not update automatically. It just displays the time the screen went black. One touch with the stylus anywhere on the screen will update the clock. To me this seems like a software problem so I am thinking of reflashing but since this issue started after the fall I am also afraid of an underlying hardware problem that could cause unexpected behavior during the flashing process.
Any suggestions or ideas?
Click to expand...
Click to collapse
i have a similar problem every once in a while that it takes a few seconds to update. best way to answer your question is to flash the stock rom, if it still does it then its hardware.
Hey guys, I was wondering if somebody would be able to maybe help me diagnose the fault\problem part with my non-working diamond...
Basically I went to a club one night and the place was unbelievably steamy / humid. My phone was working one minute and then the next it wouldnt display anything on the LCD. The backlight was working however.
Since then I havent been able to get an image on the screen although when trying to turn it on, it seems to go through its startup sequence (backlight -> vibration -> beep (i think))
I havent had any power to the phone since a day after it broke (a few weeks ago).
I'd like to get it back working again but dont know exactly what part i would need to replace. I'm fairly competent with electronics .
Any help/advite would be appreciated!
Haha, ok that's odd...
I've plugged it into my pc to get some data files off about an hour ago.. forgot about it and just looked at it now and the screen is displaying!
It is displaying and accepting input although it was flickering at first (like pixel shifting). but i pressed the power button to standby the screen and pressed it again and the display is fine with no flickering ?
Ive moved the phone about and shook it quite hard to see if there's any loose connection but the display still seems fine..
Anybody have any ideas as to what it may be?
I'm not going to deem it as fixed until I know what the problem was/is lol
cheers guys
Ok screen actually keeps flickering nonstop, and sometimes 'fades away' to gray/white/black
comes back after a few seconds though
Looks like a faulty connector?
Hello
One night I was using the phone without doing anything special , some video watching . Phone went dark, tried to reboot. Blank Screen and the capacitive buttons flash. Left it to charge all night, in the morning it started but after I pressed the lock button blank screen but phone still working and receiving input.
Took the battery and SD card out left it for 30 seconds then started it again, Stuck at LG logo. Repeat , phone started ... Pressed lock button once then again to unlock , screen wouldn't start.
Used LG Mobile Update recovery tool to restore it ... Didn't solve problem. Sometimes it does not even start , just flashes buttons, other times it does without screen and last all works even the screen until first time goes dark , in the last two cases I can use LG On-Screen Phone without trouble, in doing so I installed a proximity sensor test app to see if it was causing my screen to not come back on , the sensor looked fine.
Facts:
1. Two day old Optimus Black p970, worked like a charm until stated problem
2. The app that checked proximity sensor showed the sensor to be free when my hand wasn't on it
3. The warranty laws in my country are idiotic so I would do or buy anything rather than send it so they can give me a new one in 3 months.
4. Tried another battery from another Optimus, fully charged nothing different.
5. Stock rom.
Do any of you fine people have some ideas on how to fix this? Thanks in advance
Hi there...
Sometime ago [1 year and a half or so~] I worked at a cell refurbishing facility [there were samsung, motorola and palm devices from sprint] and that problem you have was quite usual. Blank screen, still the phone is somehow usable like reciving calls...
There's this thing called "flex" which is the connector between board and display and that is what we fix, most of the time not even "fix it" just getting it in the right place...
This happen because of excesive use in those sliding or clamshell devices, in OB could be for overheating, you could try to fix it yourself or pay $20 usd [that's what it cost here]
Would that connector explain the fact that sometimes it doesn't start at all? hmm I am thinking now and I guess if it moves and somehow the phone feels it has not display connected it could fail to start... Anyhow thank you
actually yes, it could be only for the flex [some devices don't start at all when not having display or keyboard if there's any] but since our OB is not sliding nor clamshell type probably was overheating.
you say you have stock rom, well now I'm using CM7 but when I was at stock and after using the phone a few minutes it felt warm and some more minutes [like playing gunbros where you need to use both hands and a lot of movement] it was really hot and had to stop playing for a while.
what I'm trying to say is that because of overheating flex could have moved, but because of overheating too may have move something else, you couldn't belive the huge number of micro-things that reside in the board.
so if it's only the flex, it's an easy task to do, just unplug and plug again, but if it's something else it's quite hard to know just looking at it, you need to do some electric measures and stuff, the recomendation is to take it to a tech center or something
Hi. I Have same issue. Two times when i press power buton, butons flashing and screen still black. Phone not responding. I must remove baterry.
Sent from my LG-P970 using Tapatalk
Hi there, got the same problem too with my optimus black. Screen goes flickering, shut down don't do any good, and the phone temperature is kinda hot. But in my case it work after I clean some cache and data in the phone storage through LG OSP. After that, the phone temperature back to normal and the phone screen back to normal also. I believe that in my case the phone is overheated.
Now there is another long topic on freezing, but its basically about 10seconds freeze , then things normal and stuff. Mine is different so I made a new topic.
Have sprint note. On Marshmellow now but happened on Lollipop as well.
The problem is:
After several hours of use, or may even a day, the phone just freezes....partly. Let me explain. Basically if you touch anywhere on the screen, it won't register the touch. If you hit the hard recents button, it'll show recents, but you can't click any program (it doesn't register your touch). When it first happened I thought I needed a new screen, but quickly found out I probably don't: If I hit the nav bar, it will pull down full screen, and if I have it full of notifications, I can click any of the notifications, whether its near the top, middle, or bottom, and it registers the touch and sends me to the app. But then again, at that app, the screen doesn't register. Even if I touch in the same place on the screen where I clicked the notification that sent me to the app. But the nav bar still works. It recognizes the touch, and will pull down full screen, and I can click anywhere on the screen and my touch will register. Also if I hold the power button and the reboot options come up (which on mine has option from top down to bottom, I can click any option on the screen, and it will register my touch. But if I hit the home button, the whole screen is non responsive. So I have a partial freeze. The whole screen doesn't work, but then the whole screen will work when I pull the nav bar down, so im totally confused. I already tried usually differnt launchers, but same thing, after while, screen will be non responsive
If I reboot then everything works fine and normal, so I doubt its a screen issue. Because if its broke its broke. Also tried a hard reset,problem still came back. I guess it may be an app clashing problem but I have over 100 apps it could be any one of them
Has anybody experienced something similar?
I had a buddy give me an LG Lucid3 that had a similar issue... It actually got worse over time and the touchscreen totally stopped working. (He thought) I took it apart and actually the connection was good. Put it back together and just kept rebooting it multiple times in a row. Finally, the touch started to work a little an for some reason I thought to go and download an antivirus program. The phone had 11. Got rid of them and phone has been working fine for a couple weeks now. Idk if that's your problem but I figured I'd share this experience because I've never seen anything like it.
Sent from my KYOCERA-C6745 using Tapatalk