Database Develop

Downgrade Radio Rom 1.15 ==> 1.13

I have upgrade both CErom and RadioRom as followed
CERom 5.03.02 WWE
Radio 1.15.00
Is it possible that I can downgrade to 1.13 for the RadioRom only without downgrade back to WM2003?
I used the Asia version (Thailand) I try to downgrade already but get Device ID error if i used the MaUpgradeUt_noID.exe got the connection problem I used the Activesync Ver 4
Please help me? The 1.15 list the operator not in thailand.
PS. I have notice that if I take out the battery in the boot screen the radio version will not be show (N/A) and the radio is malfunction so i have to do the soft reset to get the radio back online is there anyone face out this problem with radio 1.15 or not?

To downgrade to 1.13 or 1.12, just download the MaUpgradeUT utility from here :-
ftp://xda:[email protected]/BlueAngel/Tools/MaUpgradeUt_noID.zip
Extract the installer for your updated rom to a directory using winrar or winzip.
Goto the directory you just extracted the files to and delete all ".nbf" files, except "radio_.nbf". This will ensure that you only update the radio ROM, not the windows mobile ROM or the extended ROM.
Extract the MaUpgradeUt_NoID.zip file to the same directory as the Radio rom file "radio_.nbf" and run MaUpgradeUt_noID.exe.
The installer will show a picture of a Magician device, not a BlueAngel. This is normal and nothing to worry about.

Why is 1.13 or 1.12 radio rom preferred over 1.15?

Because 1.15 has problems with wifi and bluetooth with wm5

the radio is nothing to do with the bluetooth or wifi.
the radio is purly the firmare for the GSM chip, and basicaly to put my own experiances here 1.12, 1.13 and 1.15 work fine with 2003se, in wm5 however 1.12 and 1.13 work fine, but with 1.15 i have crap signal and only about 1 in 10 of outgoing calls actually make the dial tone, also many texts and calls are not recieved.

The Radio 1.15 good working on my Pda2K.
On the WM2003SE and WM2005 ROMs...
Your problem-is not radio.

the problem i have described only seem apparent in low signal areas afaik (like where i live), sorry i should have mentioned that before.

1.15 has these problems even in a areas with high signal, my home is in about 30 meters from the cell antenas and i had problems like this, i had it for 3 months and this occured 3-4 times for that time, but when i go to a place with low signal it was almost impossible to make a call

New Radio Rom on WM5

ok, here is the deal.
I flashed the WM5 to my device (Blue angel-qtek 9090), works great !!
standard the radio rom is 1.13.00
a newer is avail. namely 1.15.00
but (as operah says...)
i'm unable to flash the radio rom to my device, yes i checked the forum and read all the BA items....
any suggestions.
greets
ger (the Netherlands)

Go back to WM2003
You can also use the original Provider Package(here you can replace the RadioRom File).
Try to flash the Radio and then revert to WM5 again.
For me it worked.

Last time I had WM5 onmy device I flashed an new radio to see if it worked (was a VERY long time ago).
Have you followed the wiki Radio 1.15 page ?

Thanks for the info!
downgrading to 2k3, updating the radio to 1.15.00.
after that upgraded to 2k5 again.
thanks
by the way what do you mean by ... VERY long time ago....
gr,
ger

Checked wiki and based on my own updates I come up with November 2005.

HTC P3600 don't want to flash!

Hi guys,
this is one of my first post here but I read you everytime. So, the problem now is: my P3600 don't want to flash with any rom.
I've just take it back from assistance for to change the black cover (2nd time...) and when I want to flash, as before I was given to the assistence, with udK 6.1 rom it don't want to flash with any other roms!!
I've now download the Lite version of udK 6.1 and install it but when I've discovered that I prefer the full version that's start the never ending story: I tryed to flash with Full version 2 or 3 time already, the installation goes to 100% but when it restart (should it restart not power off?!?) the rom is always the same Lite version. I tried to use also the official wm5 from HTC without manual entry into bootloaded but after flashing is 100% the rom is always udK 6.1 Lite. I have SPL Olipro 1.20 installed (in the past I've had no problems at all!)
Anyone can help me to flash (with lowest risks) my P3600 again?
Thanks to everybody!

no ideas guys?

so no one can help me with an idea???

What version is your Trinity? P3600 or P3600i? Just to confirm eventhough you mentioned P3600 in the subject.

jackkkkk said:
What version is your Trinity? P3600 or P3600i? Just to confirm eventhough you mentioned P3600 in the subject.
Click to expand...
Click to collapse
it's a P3600

Do a hard reset and flash an OFFICIAL ROM from SD-card

Switch to Des' Crash Proof SPL and try flashing the ROM straight from SD card.
This should work.

thank you very much. I've already tried to change to Des Crash Proof but at about 13%-14% it gives me an error when I reboot by softreset the system is always the same. Is it normal? Is there a specific procedure to change SPL software?

If it works at all after SPL flashing, then you must have followed all procedures. Try flashing Olipro's SPL and scan for bad blocks in flash.

nightblade said:
Hi guys,
this is one of my first post here but I read you everytime. So, the problem now is: my P3600 don't want to flash with any rom.
I've just take it back from assistance for to change the black cover (2nd time...) and when I want to flash, as before I was given to the assistence, with udK 6.1 rom it don't want to flash with any other roms!!
I've now download the Lite version of udK 6.1 and install it but when I've discovered that I prefer the full version that's start the never ending story: I tryed to flash with Full version 2 or 3 time already, the installation goes to 100% but when it restart (should it restart not power off?!?) the rom is always the same Lite version. I tried to use also the official wm5 from HTC without manual entry into bootloaded but after flashing is 100% the rom is always udK 6.1 Lite. I have SPL Olipro 1.20 installed (in the past I've had no problems at all!)
Anyone can help me to flash (with lowest risks) my P3600 again?
Thanks to everybody!
Click to expand...
Click to collapse
Make sure that your SD card it out

problem installing wm6 italian rom

Hi forum.I've a problem flashing my htc p3600. When I'm trying to install a wm6 rom flashing seem to going right...Smartphone restarted correctly but I've blanc screen and i didn't see a lot of icons(for example number on telephone). Start menu working fine. I use olipro 1.20 and radio 1.46.
Any ideas?
Thanks
Djeghe

[Q] Help guys, Wifi not working at all, flashed everything

Hi all! I just got yesterday Mda Vario 3, aka kaiser, and the man who i bought it from told me that wifi need to be setup... Ok. I try wifi, it works, i connected to my router and it worked.
Read specs: radio 1.71.09.01
protocol 25.75.40.02
rom 3. abusalza and i think hard spl was 3.29
and, as far i know rom flashing, i thought get and flash new rom... i tried wm 6.1 wm 6.5... on some camera didnt work and i get a new radio and it works, BUT wifi doesnt work on any rom with any radio, i changed spl but does not work. i dont know what to do...
Any help would be gratefull