my helard p 4350
ipl 1.08.0001
spl 1.08.0001
i try to flash custom room so that happened
and when i try to flash any room its display invaild update tool
stuck on boot loader what can i do
plz advise me
thanx for ur cooperation
try this thread. read the WHOLE thread and carefully:
http://forum.xda-developers.com/showthread.php?t=417930
mr_guitar_eg said:
my helard p 4350
ipl 1.08.0001
spl 1.08.0001
i try to flash custom room so that happened
and when i try to flash any room its display invaild update tool
stuck on boot loader what can i do
plz advise me
thanx for ur cooperation
Click to expand...
Click to collapse
you could also try this:
Originally Posted by ivanmmj
So, you've decided that your shiny new toy isn't very well setup by default. You flashed a ROM and lo and behold, you missed some instruction somewhere and now you think it's bricked.
Here's the good news:
It's not bricked!!
Bricked means that it's dead and it's in no way or shape recoverable.
There is still a chance. (As long as you didn't try to hardSPL with another Device's SPL...)
All you have to do is:
For the WING:
Hold the Camera button and WHILE holding it, soft reset the device (that means press the little hole above the memory card with the stylus.) That will bring you to the bootloader. Now download the appropiate RUU and run that program. A few minutes later and your new shiny toy is back to it's crappy OEM but working self!
I'll put in links for those who can't find them...
In his case, the goldcard is the answer. He did not heed the warnings about flashing a phone with an SPL/IPL lower than 4.
ivanmmj said:
In his case, the goldcard is the answer. He did not heed the warnings about flashing a phone with an SPL/IPL lower than 4.
Click to expand...
Click to collapse
thats what i thought.
what the gold card
actually i falsh a new room through hard spl then i try to falsh another one through ruu,
but now when i go through bootloader and the three coloure displayed i cant flash any rom cuz its stopped at 0% and the msg invalid,,,,,,,,,,,,,
so ?
What did you flash the second time? It broke your SPL and IPL.
Search for the word Goldcard.
spacemonkey333 said:
try this thread. read the WHOLE thread and carefully:
http://forum.xda-developers.com/showthread.php?t=417930
Click to expand...
Click to collapse
i gave him the goldcard link already
thanx for the link mr but it must need a memory card
is that right
and the steps is not clearly
plz any one help me
[email protected] plz contact me via mssenger
Br
is there any way to get back my device gold card doesnt work
That's the only known method. If it's not working properly, make sure you're following the steps properly. If it still doesn't work, then it's repair time... Sorry.
Done ,, gold card is great
thanx my friends
Related
I have an 8125 that I can't seem to get off of the RUU screen. It shows IPL 2.25.0001 and SPL 2.25.0001. Every time I try to use the HTC software update it reaches 95% and then errors out. Any idea how I can get this phone working again?
Thanks,
T
you have a G4 wizard, you need to install the wizard love rom. I believe if you read around, you may be able to find out where to find it. Also read some info about unlocking your CID and SIM for a G4 Wizard.
t_matheus said:
I have an 8125 that I can't seem to get off of the RUU screen. It shows IPL 2.25.0001 and SPL 2.25.0001. Every time I try to use the HTC software update it reaches 95% and then errors out. Any idea how I can get this phone working again?
Thanks,
T
Click to expand...
Click to collapse
I found this in another thread, try it.
--------------------------------------------------------------------------------
Hi there,
If you ever happen to get stuck in the IPL / SPL screen, try the following (it happened to me and I almost got a heart attack...):
"If your device doen't boot after flash procedure with my shelltool you should
1) Hold "Camera" while short pressing the "reset" button. Your device will enter in bootloader mode. You will se 3 stripes.
2) You should connect your usb cable to your device and pc and run RUU and flash this rom.
http://rapidshare.com/files/17792050/Wizard_Love_2.26.10.2_WWE_Novii_CF2.rar
3) read my instruction once more and repeat all step by step. its very important!!"
[I've edited the download link for the love rar, the original one on the ftp server was deleted]
t_matheus said:
I have an 8125 that I can't seem to get off of the RUU screen. It shows IPL 2.25.0001 and SPL 2.25.0001. Every time I try to use the HTC software update it reaches 95% and then errors out. Any idea how I can get this phone working again?
Thanks,
T
Click to expand...
Click to collapse
Suggestion.
Go to IMEI Check, buy the unlock and have fun upgrading and downgrading your ROM.
It cost you some money but you can restore your device without to much trouble.
Best regards.
golfernutnflorida said:
I found this in another thread, try it.
--------------------------------------------------------------------------------
Hi there,
If you ever happen to get stuck in the IPL / SPL screen, try the following (it happened to me and I almost got a heart attack...):
"If your device doen't boot after flash procedure with my shelltool you should
1) Hold "Camera" while short pressing the "reset" button. Your device will enter in bootloader mode. You will se 3 stripes.
2) You should connect your usb cable to your device and pc and run RUU and flash this rom.
http://rapidshare.com/files/17792050/Wizard_Love_2.26.10.2_WWE_Novii_CF2.rar
3) read my instruction once more and repeat all step by step. its very important!!"
[I've edited the download link for the love rar, the original one on the ftp server was deleted]
Click to expand...
Click to collapse
I have a 8125 as well and just run the wizard love as above and you will be back in business. As for unlocking you can use latest lokiwiz for free as posted in the forums.
cybercub said:
I have a 8125 as well and just run the wizard love as above and you will be back in business. As for unlocking you can use latest lokiwiz for free as posted in the forums.
Click to expand...
Click to collapse
You can only unlock a G3 Wizard like that. G4's are different and have to be unlocked via imei check. The OP has a G4 based on their IPL/SPL they posted.
I can't seem to get my hands on this file. I've tried several places but no joy. Any thoughts on where I can lay my hands on the Wizard_Love ROM?
Thanks,
T
golfernutnflorida said:
I found this in another thread, try it.
--------------------------------------------------------------------------------
Hi there,
If you ever happen to get stuck in the IPL / SPL screen, try the following (it happened to me and I almost got a heart attack...):
"If your device doen't boot after flash procedure with my shelltool you should
1) Hold "Camera" while short pressing the "reset" button. Your device will enter in bootloader mode. You will se 3 stripes.
2) You should connect your usb cable to your device and pc and run RUU and flash this rom.
http://rapidshare.com/files/17792050/Wizard_Love_2.26.10.2_WWE_Novii_CF2.rar
3) read my instruction once more and repeat all step by step. its very important!!"
[I've edited the download link for the love rar, the original one on the ftp server was deleted]
Click to expand...
Click to collapse
t_matheus said:
I can't seem to get my hands on this file. I've tried several places but no joy. Any thoughts on where I can lay my hands on the Wizard_Love ROM?
Thanks,
T
Click to expand...
Click to collapse
I was able to pull it from RapidShare in the link that you provided. Its also seeded on PirateBay if you prefer the Torrent method...
mfrazzz said:
I was able to pull it from RapidShare in the link that you provided. Its also seeded on PirateBay if you prefer the Torrent method...
Click to expand...
Click to collapse
Got it and now the phone is working again!
So do I need to unlock the phone and install another ROM or will it work fine with this ROM?
Thanks, again for all your help!
T
Based on your original post, you have a G4 Wizard. You can't do the standard unlock like the stickies from Dr. P and Faria describe. You have to use the other sticky for installing roms with a CID locked phone. Your other option is to go to Imei Check and do their unlock (will cost about USD 40). Its all online (you give them your IMEI and some other info with your payment and then they send you the files to do the unlock). But even then, you still have to use G4 roms (so you need to be careful or you'll be back in this situation or worse).
BTW:I've never messed with a G4 Wizard so I'm only stating what I've read. Go read and re-read the CID Locked install procedure in the stickies to learn more.
So, you've decided that your shiny new toy isn't very well setup by default. You flashed a ROM and lo and behold, you missed some instruction somewhere and now you think it's bricked.
Here's the good news:
It's not bricked!!
Bricked means that it's dead and it's in no way or shape recoverable.
There is still a chance. (As long as you didn't try to hardSPL with another Device's SPL...)
All you have to do is:
For the WING:
Hold the Camera button and WHILE holding it, soft reset the device (that means press the little hole above the memory card with the stylus.) That will bring you to the bootloader. Now download the appropiate RUU and run that program. A few minutes later and your new shiny toy is back to it's crappy OEM but working self!
I'll put in links for those who can't find them...
Here's tmobile's ROM.
WOW! That´s all??
Ok - then provide us a link to a XDA Terra RUU!!!!!!
hahahaha. Thanks for this help. Maby for some people it is usefull - but written 1000 times before.
ivanmmj said:
So, you've decided that your shiny new toy isn't very well setup by default. You flashed a ROM and lo and behold, you missed some instruction somewhere and now you think it's bricked.
Here's the good news:
It's not bricked!!
Bricked means that it's dead and it's in no way or shape recoverable.
There is still a chance. (As long as you didn't try to hardSPL with another Device's SPL...)
All you have to do is:
For the WING:
Hold the Camera button and WHILE holding it, soft reset the device (that means press the little hole above the memory card with the stylus.) That will bring you to the bootloader. Now download the appropiate RUU and run that program. A few minutes later and your new shiny toy is back to it's crappy OEM but working self!
I'll put in links for those who can't find them...
Click to expand...
Click to collapse
papamopps said:
WOW! That´s all??
Ok - then provide us a link to a XDA Terra RUU!!!!!!
hahahaha. Thanks for this help. Maby for some people it is usefull - but written 1000 times before.
Click to expand...
Click to collapse
I know it has been stated a million times. I'm just tired of the same question being asked over and over again and so here we are...
Too bad it'll be stated a million more times afterwards too.
falconeyez said:
Too bad it'll be stated a million more times afterwards too.
Click to expand...
Click to collapse
If we sticky it and threatened their lives if they don't read it... lol
ivanmmj said:
For the WING:
Hold the Camera button and WHILE holding it, soft reset the device (that means press the little hole above the memory card with the stylus.) That will bring you to the bootloader. Now download the appropiate RUU and run that program. A few minutes later and your new shiny toy is back to it's crappy OEM but working self!
Click to expand...
Click to collapse
It will not help!
ASerg said:
It will not help!
Click to expand...
Click to collapse
And we hold their pet's hostage?
ivanmmj said:
And we hold their pet's hostage?
Click to expand...
Click to collapse
Or better yet, tell them to send us their phones, then we "unbrick" them and sell them on eBay.
falconeyez said:
Or better yet, tell them to send us their phones, then we "unbrick" them and sell them on eBay.
Click to expand...
Click to collapse
Might work out, I get 10% of the over all sold
Ghostrider
Ghostrider said:
Might work out, I get 10% of the over all sold
Ghostrider
Click to expand...
Click to collapse
Fine, but I get 15% because it's my thread.
The instructions to do this are actually in my newbie thread. Which is a sticky.
TylerC161 said:
The instructions to do this are actually in my newbie thread. Which is a sticky.
Click to expand...
Click to collapse
I know, but most people don't search. I figured, maybe if it says "How to fix your bricked phone" on the title, they might get the idea.
It was actually done mostly as a joke...
help
I used the hardSPL from this thread..
http://forum.xda-developers.com/showthread.php?t=358225
It worked successfully and I was able to restart into WM6. Then I tried loading the TouchIT 4.4 and it installed cleanly with no errors. But when I went to restart it, my Wing just sits there at the CanonYang boot screen and never changes.
I tried using the steps here to restore the tmo default rom, but it after 1% on the progress bar, the screen goes blank and the CanonYang screen comes back. Is there anything I can do?
edit: I can get to the bootloader screen with the color bars. I'm not sure if this additional info will be of any help.
IPL 4.10.0002
SPL 4.70.Yang
gumbico said:
I used the hardSPL from this thread..
http://forum.xda-developers.com/showthread.php?t=358225
It worked successfully and I was able to restart into WM6. Then I tried loading the TouchIT 4.4 and it installed cleanly with no errors. But when I went to restart it, my Wing just sits there at the CanonYang boot screen and never changes.
I tried using the steps here to restore the tmo default rom, but it after 1% on the progress bar, the screen goes blank and the CanonYang screen comes back. Is there anything I can do?
edit: I can get to the bootloader screen with the color bars. I'm not sure if this additional info will be of any help.
IPL 4.10.0002
SPL 4.70.Yang
Click to expand...
Click to collapse
SPL 4.70.yang!!! your device is HARD-SPL!!
So going back to stockrom--> delete the SPL.nbh from EVERY RUU you are running.
Then it shouldn´t stop......
Big Thanks papa! That did the trick. My Wing is happy once again and running Open Touch. But I still want to give TouchIt another try.
And what if i cant find stock RUU mine came with some arabic keyboard and spl was 1.08 , thanks to Oli he didnt mention that SPL should be 4 or higher , so device is bricked since first Olis release and no way to find this arabic stock RUU.
Any Help ?????
Hitec
If the device had an spl of 1.08 prior to HardSPLing it, then you'll have to bring the device to your nearest repair center. There isn't a way around that. Oli doesn't know everything and that's the risk we take when we try new and experimental things that people create but have no way of testing. But, we live and learn. If it wasn't for that issue, you could always cook your own ROM and if the HardSPL was working, you could've easily flashed any ROM. But the keyboard wouldn't been wrong until you could find someone who had the correct keyboard and you extracted the ROM from it and cooked that keyboard driver into your ROM.
Oh noooo!!
Hi ivanmmj,
I used your guide to flashing my HTC P4350 at http://forum.xda-developers.com/showthread.php?t=358615.
It was in French and I wanted it in English. So I downloaded one of the official HTC ROMs "HTC_P4350_WWE_4.17.405.2_4.1.13.44_02.94.90_Ship.exe" assuming this was the English one because all the others couldn't have been.
I copied the "RUU_signed.nbh" from the above HTC ROM and put it into the RUU folder as instructed by yourguide (I didn't copy the SPL.nbh file). I then ran the herald-uspl.exe and everything went fine until the RUU utility stopped with the error "invalid vender ID".
The RUU exited without completing, now all I get when the device boots is the screen giving my IPL (1.08.001) and SPL (1.08.001). How do I flash another ROM from this state? I can't do it the "normal" way because ActiveSync can't see the device. When I try to use the RUU tool that comes with your tool, the progress bar shows then it says the tool can't be used with my device.
Someone please help!
foo_bar_baz said:
Hi ivanmmj,
I used your guide to flashing my HTC P4350 at http://forum.xda-developers.com/showthread.php?t=358615.
It was in French and I wanted it in English. So I downloaded one of the official HTC ROMs "HTC_P4350_WWE_4.17.405.2_4.1.13.44_02.94.90_Ship.exe" assuming this was the English one because all the others couldn't have been.
I copied the "RUU_signed.nbh" from the above HTC ROM and put it into the RUU folder as instructed by yourguide (I didn't copy the SPL.nbh file). I then ran the herald-uspl.exe and everything went fine until the RUU utility stopped with the error "invalid vender ID".
The RUU exited without completing, now all I get when the device boots is the screen giving my IPL (1.08.001) and SPL (1.08.001). How do I flash another ROM from this state? I can't do it the "normal" way because ActiveSync can't see the device. When I try to use the RUU tool that comes with your tool, the progress bar shows then it says the tool can't be used with my device.
Someone please help!
Click to expand...
Click to collapse
Oh wow. I'm so sorry. I think I may have forgotten to put up a warning for people that have an SPL lower than 4.0. Was your SPL lower than 4.0? If it was, you cannot use the USPL OR the HardSPL and they end up writing part of the ROM over your current SPL and brick the device. This, unfortunately, needs to be fixed by your local repair center. I'll talk to the Mods about unlocking that thread so that I can update it.
ivanmmj said:
Oh wow. I'm so sorry. I think I may have forgotten to put up a warning for people that have an SPL lower than 4.0. Was your SPL lower than 4.0? If it was, you cannot use the USPL OR the HardSPL and they end up writing part of the ROM over your current SPL and brick the device. This, unfortunately, needs to be fixed by your local repair center. I'll talk to the Mods about unlocking that thread so that I can update it.
Click to expand...
Click to collapse
Oh deary me! I am so dead now - I live in Tanzania, East-Africa. My "local" repair center is several hundred thousand miles away across The Big Blue. What exactly do the repair center folks do to fix the device? Perhaps I can soldier out myself with some guidance...
Thank you,
foo_bar_baz.
hello could anyone help me ?
my device is stuck in bootloader and its recognized by the PC
this happened when i was trying a cooked rom
IPL 1.09.0001
SPL (ditto)
I searche everywhere an there seem to be only ways out for people with SPL 4.00.xxxx
is there a way out ??
thank you
sorry fr the bump but i really need help
I tried placing the phone in bootloader and installing the official HTC rom
but i get an ERROR 300
and the percentage is stuck at 0 on the screen
Try to flash your device with the Stock ROM.
That usually works
He already tried this, but it didnt work.
Let me just quote a post from dougstoner:
dougstoner said:
Well, yes and no. In the long run, it's better to Hard spl your phone. A lot of the roms in the forum require hard spl first. If you somehow fail during the hard spl, then you end up with a "brick". I used the uspl method first to flash, and it was a little easier to do, but hard spl'ing insn't complicated either. You just have to make sure of your ipl number is higher than 4. You can check this by holdign down the camera button, and press the soft reset button (use the stylus on the side to press) and continue to hold the camera button until you get to what's called the bootloader screen. It's red, blue, and green. Here are the instructions for hard spl, but MAKE SURE your ipl number is hight FIRST. If it isn't, you will brick your phone.
I case of people who don´t read 200 post and still brick their device - here is the guide that worked for ALL people with:
HTC P4350
XDA Terra
WING
with IPL 4.xxx and higher!!! (that is IMPORTANT)
and then follow this:
Default
For me it was working when:
1. install canonyang.cab
2. install aserpolicy.cab
3- install disablesecurity.cab
4. SOFTRESET
5. run RUU from Hard-SPLWM6 folder verison 4.70.yang
6. screen will become white - WAIT until it reboots itselfe.
7. done!
check if SPL now is 4.70.yang
Fore sure: I used this
http://rapidshare.de/files/38148213/...l_WM6.rar.html
mirror: http://www.sendspace.com/file/ot8zsn
It worked for many others, too.
Click to expand...
Click to collapse
So the IPL should at least be 4.xx but as you posted yours is 1.xx?! Might this be the issue?
Unfortunately, a SPL of 1.x after a hardspl/USPL means that the phone has been permanently bricked. Did you try to hardSPL your device or use USPL? They're both only compatible with 4.x SPL's.
I saw that someone recently came up with a way to fix bricked phones. They weren't Heralds, I forgot what they were... They basically found a way to use a buffer overrun on the SPL to launch code so they could launch a patched SPL and reflash... i wonder if our SPL's have that same bug and the method could be applied to us, too.
hey,
if my Herald is IPL 1.xxx can I somehow make it a 4.xxx? Or is there no chance to flash other roms? What does the IPL depend on? Production date?
thanks everyone for your patient replies
I guess for IPL 1.x there seems to be no solution as of now !!!
it was actually working initially with touch IT after Hard spl but i wanted to give a try to another version of touch it thats when the device got bricked .
I feel really sorry for you, but dont give up yet. As ivanmmj said, there could be a solution. Just check the forum.
I am not sure whether it helps but I did a little search and found severals threads:
Fix Bricked HTC ELF/ELFin
Someone with the same ERROR300 as yours
good luck
xtc.sanchez said:
I am not sure whether it helps but I did a little search and found severals threads:
Fix Bricked HTC ELF/ELFin
Someone with the same ERROR300 as yours
good luck
Click to expand...
Click to collapse
thanks so much mate !!! I will look into it right away
iv done all the reading
iv heard there was a way to flash the ROM through SD so i did try using
HERAIMG.nbh for the official rom from the HTC website !!
somehow the ROM does not work (invalid rom)
id try a couple of roms !!maybe ill be lucky !!
thanks again xtc.sanchez and everyone else
its been very informative and helpful
ipl spl 1.08.0001
the gold card desnt work so what can i do
i tried every thin hard reset goldcard ????????????
If you followed the "goldCard" walkthrough step by step and did exactly as the thread said, then it should have worked for you. Unfortunately, that is your only hope. Maybe you have a hardware problem.
yeaaaaaaaaaaaas , thanx god aND THANK U my friend its working again
so tell me if i wanna install another room what can i do ?
my ipl now is 4 xx after the gold card operation
thanx
mr_guitar_eg said:
yeaaaaaaaaaaaas , thanx god aND THANK U my friend its working again
so tell me if i wanna install another room what can i do ?
my ipl now is 4 xx after the gold card operation
thanx
Click to expand...
Click to collapse
your "SPL" needs to be above 4.0.0.0. If it is, you need to hardspl your device.
Go to the following link and follow the instructions exactly as they are written:
http://forum.xda-developers.com/showthread.php?t=358225
after you are hardspl, then you can flash your custom rom
Use GoldCard method. More secure than hardSPL, and u have infinite ability... Endless possibilities
You can flash anything that u want without hardSPL... Just put ur favorite flash and its done
pd. You'll got 4.0 at end of process
thanx sir for ur help
best regards
This is for ne one that is looking for detail in making their Wing/Herald hard spl'd
Please do not get mad at me if it does not work.. But there are a ton of success stories with flashing Wing/Herald to Hard SPL..
#1:
Ok first check your ipl and spl.. You can do this by entering bootloader. bootloader (push the pin hole right under volume slide and hold camera button) you will then enter bootloader.. It looks like 3 color bars and say's ipl 4.xxxxx whatever and spl 4.xxxxx same.. Whatever the 4.xxx is thats what ipl and spl you are.. In order to become hard spl you must at least 4. and higher.. So if you see a 4 then your good..
#2:
Ok now that we have checked, soft reset your phone again and let it load.. This will get you out of bootloader and back to normal mode.. I was very careful on flashing.. So i always reverted back to oem rom.. So get the oem Wing rom or Herald rom.. If you can't find it let me know because i have it.. So just flash oem and let it be stock rom..
#3:
Ok now is getting ready to start from the very beginning.. Now if you have the 3 cabs (canonyang.cab, aserpolicy.cab, disablesecurity.cab) just install them in order as writen . After they were successfully installed soft rest your phone again..
#4:
Ok now we start the flash.. Its a scary few moments lol.. But very worth it.. Make sure you are synced and connected to your comp.. I also was extra careful by resetting my comp and making sure all windows were closed and made it so windows weren't open.. But i was extra careful Check the circle and make sure its green or if you have vista it'll be the pda icon lite up.. now open your hard spl folder (the rar. or folder that you dl'd for from the main page) and click on ROMUpdateUtility. Now just wait for it to finish the flash.
- If all goes well then it will come up something like Yang something something.. You will see a dif splash due to you dl'ing a new rom that makes your phone hard spl'd. Let it finish and your good.. Soft reset and enter bootloader and see if spl is 4.70 yang.. If so congrats your hard spl'd!!!!!! fo sho...
* Now to flash other roms all you have to do is get your oem rom and right click on it.. Extract it and you will see its contents.. Among its contents delete the spl.nbh file. Not the ruu.nbh.. Now you click romupdateutility.. I would make the extracted oem a special folder because this is now your new flashcenter.. Ne time you would like to flash a new rom all you have to do is simply replace the rom .nbh of your liking in this folder that you made and run romupdate.. All done.. Easy flashing.. lol.. Welcome to hard spl world!!! Now you can flash at ease.. Ne Herald/ Wing rom you have is now flashable except roms designed for micro sd cards (trasflash cards) Just use the .nbh files..
Please if you are are not ok with my instructions and wish special help(detailed help) with this put it on this thread. Others will learn from others concerns.. Even if the ? has been asked a million times still ask.. Please ask ?'s before flashing if something does not go with instructions..
Once again i'm not responsible for ne thing that happens to your wing/herald.. I am simply trying to help in-detail and be at assistance in ne way possible..
This is the dl from the orginal Hard SPL page. It contains everything thing you need.. (cab. files, .nbh for flahsing and romutility for flashing)
Give credit to Papamopps's for starting the Hard SPL thread
http://rapidshare.de/files/38148213/HardSpl_WM6.rar.html
This is the oem tmobile rom update:
http://rapidshare.com/files/148795008/TMo_Wing_RUU_Update_4.26.531.4.exe
Good manual! thanks!
ruebyi said:
Good manual! thanks!
Click to expand...
Click to collapse
no problem.. i had a friend in a dif thread needing help with hard spl and was looking for detail.. so here it is.. plus ill be as much support as i can be.
trust me if you follow those steps it will work and you will be on your way to great things
I have a question, I hard spl'd my wing before but since than I got another one since it broke. Do I have to install the cab files in a special order? It seems that I remember doing this in a special order before. I hope I did not over look this question in your thread. Good post by the way.
lmyers10 said:
I have a question, I hard spl'd my wing before but since than I got another one since it broke. Do I have to install the cab files in a special order? It seems that I remember doing this in a special order before. I hope I did not over look this question in your thread. Good post by the way.
Click to expand...
Click to collapse
On the original thread there is a specific order.. canonyang.cab, aserpolicy.cab, disablesecurity.cab.. I had a second wing and did not fallow this order.. i just did it from bottom to top in alphabetical order. i kinda didnt care with the second wing thou.. i would do as the first theard says.. i totally forgot that there is an order.. i will edit.. thanks..
iPhone iWing said:
On the original thread there is a specific order.. canonyang.cab, aserpolicy.cab, disablesecurity.cab.. I had a second wing and did not fallow this order.. i just did it from bottom to top in alphabetical order. i kinda didnt care with the second wing thou.. i would do as the first theard says.. i totally forgot that there is an order.. i will edit.. thanks..
Click to expand...
Click to collapse
I wasnt busting your chops ,just wanted to make sure I remembered right. I will be using your directions as a guideline as I am getting ready to hard spl my phone again.
lmyers10 said:
I wasnt busting your chops ,just wanted to make sure I remembered right. I will be using your directions as a guideline as I am getting ready to hard spl my phone again.
Click to expand...
Click to collapse
O no man i wasn't coming close to taking it like that.. It was a big reminder!! Thank you.. Like i said thou i didnt do them in order on my other wing and it worked without a prob.. But do as recommended now.. I put that they need to be in the order i have posted.. Thanks.. I hope your hard spl goes great!!!
fo_sho..
thanks these are great instruction.and i believe anybody should b able to hard spl afer reading these directions...but hey who knows
Thanks it worked perfect
Ditto here. Thank you very, very much. Good instructions!
One little thing: "aserpolicy.cab" is actually "ASerg Policies.CAB" and "disablesecurity.cab" is "Disable_Security.cab" in the OEM ROM you provided a link to.
I just got a used Wing off Ebay. My IPL is 4.10.0002 and my SPL is 4.10.0000 and when I try to HardSPL I get to where the progress bar is but then it says it can't communicate with my PDA/PHone and dies on me.
I installed the CAB files in the order stated then soft reset then ran the ROM UPdate Utility. ActiveSync is active but it says it can't communicate. Did I do something wrong?
Thanks for any help.
*** Edit*** Got this figured out. I needed to go to Settings->Connections->USB to PC and check the box for Advanced Communications then run the ROM Update Utility
Lance
I followed these instructions perfectly, I got the new "yang" splash, I checked the bootloader and it confirms the spl is 4.70 yang but when i soft reset to get out of the bootloader and try to start the phone up it says:
"Error-Device start up failed due to sudden loss of power. Please click Yes or No to continue."
But there wasnt a power loss, and it wont let me click yes or no. Anyone know what happened and what I should do?
EDIT: Never mind, I got it fixed.
chaotic646 said:
I followed these instructions perfectly, I got the new "yang" splash, I checked the bootloader and it confirms the spl is 4.70 yang but when i soft reset to get out of the bootloader and try to start the phone up it says:
"Error-Device start up failed due to sudden loss of power. Please click Yes or No to continue."
But there wasnt a power loss, and it wont let me click yes or no. Anyone know what happened and what I should do?
EDIT: Never mind, I got it fixed.
Click to expand...
Click to collapse
Maybe post how in case this happens to someone else?
iPhone iWing said:
This is for ne one that is looking for detail in making their Wing/Herald hard spl'd
Please do not get mad at me if it does not work.. But there are a ton of success stories with flashing Wing/Herald to Hard SPL..
#1:
Ok first check your ipl and spl.. You can do this by entering bootloader. bootloader (push the pin hole right under volume slide and hold camera button) you will then enter bootloader.. It looks like 3 color bars and say's ipl 4.xxxxx whatever and spl 4.xxxxx same.. Whatever the 4.xxx is thats what ipl and spl you are.. In order to become hard spl you must at least 4. and higher.. So if you see a 4 then your good..
#2:
Ok now that we have checked, soft reset your phone again and let it load.. This will get you out of bootloader and back to normal mode.. I was very careful on flashing.. So i always reverted back to oem rom.. So get the oem Wing rom or Herald rom.. If you can't find it let me know because i have it.. So just flash oem and let it be stock rom..
#3:
Ok now is getting ready to start from the very beginning.. Now if you have the 3 cabs (canonyang.cab, aserpolicy.cab, disablesecurity.cab) just install them in order as writen . After they were successfully installed soft rest your phone again..
#4:
Ok now we start the flash.. Its a scary few moments lol.. But very worth it.. Make sure you are synced and connected to your comp.. I also was extra careful by resetting my comp and making sure all windows were closed and made it so windows weren't open.. But i was extra careful Check the circle and make sure its green or if you have vista it'll be the pda icon lite up.. now open your hard spl folder (the rar. or folder that you dl'd for from the main page) and click on ROMUpdateUtility. Now just wait for it to finish the flash.
- If all goes well then it will come up something like Yang something something.. You will see a dif splash due to you dl'ing a new rom that makes your phone hard spl'd. Let it finish and your good.. Soft reset and enter bootloader and see if spl is 4.70 yang.. If so congrats your hard spl'd!!!!!! fo sho...
* Now to flash other roms all you have to do is get your oem rom and right click on it.. Extract it and you will see its contents.. Among its contents delete the spl.nbh file. Not the ruu.nbh.. Now you click romupdateutility.. I would make the extracted oem a special folder because this is now your new flashcenter.. Ne time you would like to flash a new rom all you have to do is simply replace the rom .nbh of your liking in this folder that you made and run romupdate.. All done.. Easy flashing.. lol.. Welcome to hard spl world!!! Now you can flash at ease.. Ne Herald/ Wing rom you have is now flashable except roms designed for micro sd cards (trasflash cards) Just use the .nbh files..
Please if you are are not ok with my instructions and wish special help(detailed help) with this put it on this thread. Others will learn from others concerns.. Even if the ? has been asked a million times still ask.. Please ask ?'s before flashing if something does not go with instructions..
Once again i'm not responsible for ne thing that happens to your wing/herald.. I am simply trying to help in-detail and be at assistance in ne way possible..
This is the dl from the orginal Hard SPL page. It contains everything thing you need.. (cab. files, .nbh for flahsing and romutility for flashing)
Give credit to Papamopps's for starting the Hard SPL thread
http://rapidshare.de/files/38148213/HardSpl_WM6.rar.html
This is the oem tmobile rom update:
http://rapidshare.com/files/148795008/TMo_Wing_RUU_Update_4.26.531.4.exe
Click to expand...
Click to collapse
Awesome. I was worried about doing this because everything seemed out of date and etc on here but I figured the hell with it, it's been months and so many hours this week and it worked. Thanks. I was a little worried about the spl because it looked like an older version and said wm6 and not 6.1. Well everything worked out great, thanks for this. After hours and days of reading every thing I could, this was the only that did not leave me with too many unanswered questions making me worried about doing this.
*UPDATE* So I I did another one today (or tried) and kept getting that 260 error and don't know why yet (I know; it is some place in the forums) and after having it do it about 5 times I checked (unlike you said to) and it never updated the spl etc I was in a hurry but I don't think the error was my fault. But now I have a question: What exactly are the 3 cab files for? At first I thought that was what did the hard spl but then after doing it and reading this again (I learn by doing not reading) I realizied it is not. And second question is: Why does it have to be flashed with that ROM to hard spl it?
apathetic said:
Maybe post how in case this happens to someone else?
Click to expand...
Click to collapse
It did allow me to click yes, I was just trying to touch the yes with my stylus but I had to click the left soft key. I dont know what caused the error but it seems to be working fine now and Ive successfully flashed 4 different roms.
chaotic646 said:
It did allow me to click yes, I was just trying to touch the yes with my stylus but I had to click the left soft key. I dont know what caused the error but it seems to be working fine now and Ive successfully flashed 4 different roms.
Click to expand...
Click to collapse
Oh ok. I did 3 today and still did not see that (tg)
Hi!
Thanks for all the explanations.
My IPL is 4.18.0002 and SPL4.18.0000.
My phone is locked by a brazilian cell commpany TIM. Do I need to unlock my herald before to do a hard spl?
Thanks in advance
Gorbo
Hi Gordo, I am from Porto Alegre too and I hard-spled ok here.
You dont need to unlock before to do a hard spl.
Thanks.
apathetic said:
Maybe post how in case this happens to someone else?
Click to expand...
Click to collapse
I have done the same yesterday ... the thing was I've forgot the storage card in the phone. There was mess of previous installation (mostly WM5). Today I've made clear installation of the official WM6 with the card out of slot. It is working perfect now.