i was trying to unlocker the phone but for some reason active sync crashed and it didn't finish. then i attempt to recover and unlock again but active sync doesn't detect 262.
how do i get out of bootloader since it's stuck and hardreset won't get me out of it. nor does reseting nor powering off.
twe90kid said:
i was trying to unlocker the phone but for some reason active sync crashed and it didn't finish. then i attempt to recover and unlock again but active sync doesn't detect 262.
how do i get out of bootloader since it's stuck and hardreset won't get me out of it. nor does reseting nor powering off.
Click to expand...
Click to collapse
As far as I know, if you trash the ROM the device is screwed.
no fix? that means i need to go throughu insurance?
hmmm, sounds like your phone might be bricked! how about if you sale it to me half the price you got it for, then I'll take it and throw hardspl on it right before flashing a stock rom ;0)
Now it's in bootloader mode you can load a new ROM.... When you plug the cable in the PC does it say 'USB' on the bootloader screen? If so then you can use RUU to flash a new ROM. But from what you're saying you get an error when you try and do that? Hmm.
This is why I keep DIAMIMG.nbh on the 4GB just in case things like this happen then you can restore from that.
Maybe take it to a mobile phone repairer and see if they can force flash an image. I've had that done with many Nokia's but I don't know it that's possible with a WinMo device..
If you've already HardSPL'd your device then you have voided the warranty. I guess as you said insurance may be your best bet. Good luck
salada2k said:
Now it's in bootloader mode you can load a new ROM.... When you plug the cable in the PC does it say 'USB' on the bootloader screen? If so then you can use RUU to flash a new ROM. But from what you're saying you get an error when you try and do that? Hmm.
This is why I keep DIAMIMG.nbh on the 4GB just in case things like this happen then you can restore from that.
Maybe take it to a mobile phone repairer and see if they can force flash an image. I've had that done with many Nokia's but I don't know it that's possible with a WinMo device..
If you've already HardSPL'd your device then you have voided the warranty. I guess as you said insurance may be your best bet. Good luck
Click to expand...
Click to collapse
yes it does show usb in the bootloader. but te computer wont detect the device since acticesync doesnt recognize it. also the unlock never succeeded so its still locked but stuck in boot screen
twe90kid said:
yes it does show usb in the bootloader. but te computer wont detect the device since acticesync doesnt recognize it. also the unlock never succeeded so its still locked but stuck in boot screen
Click to expand...
Click to collapse
You don't need activesync to flash a ROM when the device is in bootloader. The RUU should detect that the device is attached.
TomInMB said:
You don't need activesync to flash a ROM when the device is in bootloader. The RUU should detect that the device is attached.
Click to expand...
Click to collapse
but it doesnt show in the rru the previous rom loaded. the rru dosnt seem to correctly read the phone
twe90kid said:
but it doesnt show in the rru the previous rom loaded. the rru dosnt seem to correctly read the phone
Click to expand...
Click to collapse
Does the RUU give an error?
TomInMB said:
Does the RUU give an error?
Click to expand...
Click to collapse
i think so. what happens if it does? im out right now and ill try asap when i get back home
You would get a specific error code. Go ahead and try it...I feel confident it will work.
wat would happen if i get a error?
twe90kid said:
wat would happen if i get a error?
Click to expand...
Click to collapse
The RUU would stop (most likely before flashing started) and it would report a specific 3-digit error code.
i hope i dont get error 262 like i did when trying to unlock.
will report back later when i get home
Take a look here also. If error 262 is from RUU, that is recoverable.
http://forum.xda-developers.com/showpost.php?p=1177210&postcount=5
yup got error 262 but i tried this and it didn't work
-> ERROR [262] : UPDATE ERROR
This error occurs during the CE ROM code upgrade process.
Solution: If this happens, you can just soft-reset the device and run RUU again. The update process will then continue.
Note: At this stage, the Wince is destroyed; instead, it is in upgrade mode.
the bootloader shows this
it brings me here
security unlock
DIAM500
SPL-0.57.0000
MicroP-Diam (LES) vB
PSQC Diam STAGE_EVT V20
it says this in the middle of the screen
upgrade rom code error
please try again
but when i try again i get error 262. active sync doesn't detect the device either
anyone got any idea? thanks
bump.... i keep getting errror 262 on flash
Are you trying to flash a ROM or SPL??? You should be flashing the unsigned-HardSPL before trying to flash a ROM.
Related
I was running xelencin's latest custom rom. I have used his previous versions and all was good.
This one hung at 98%. I was just letting it do its thing when out of nowhere, BSOD. So now my phone is just sitting at 98%. I thought there was a forum post here about recovering but I'm not able to find it.
Thanks.
Update: After a soft reset, I am back to the multicolor screen. When I plug it in, it says USB in the bottom left hand corner. Device manager shows a PocketPC USB Sync device as well.
When I perform a hard reset (Comm Button + Voice Dial held, then press soft reset with stylus), I am taken right back to the same multicolor screen.
You're at the bootloader.
This is a Good Thing(tm).
At this point, you should be able to rerun any (assuming you are CID unlocked) any RUU ROM upgrade. Let it do its thing and you'll be good to go.
gamescan said:
You're at the bootloader.
This is a Good Thing(tm).
At this point, you should be able to rerun any (assuming you are CID unlocked) any RUU ROM upgrade. Let it do its thing and you'll be good to go.
Click to expand...
Click to collapse
For those that get stuck here in the future:
I had to extract the installer so as I could get past the CID unlock. I then ran "ROMUpdateUtility_Wizard_NoID.exe" and all went well!
rosewood said:
For those that get stuck here in the future:
I had to extract the installer so as I could get past the CID unlock. I then ran "ROMUpdateUtility_Wizard_NoID.exe" and all went well!
Click to expand...
Click to collapse
Yep, I went thru the exact same thing yesterday when trying to upgrade to 2.24. My PC decided to shutdown (not restart, a complete instant shutdown!) at 8% flashing. I decided to grab the "Mr Clean AKU2.3 ROM" which already had the ROM flash program available separately and then just put in the .nbf file I wanted and it was good to go
if your not cid unlocked, then what? xtract what? to wherehow can i transfer any thing, it seems though the device screen says usb, the avtivesync doesnt detects my phone. n?m, ive got it
What happen when your not CID unlocked? I had removed my hardspl before I tried to again flash a rom. I am stucked with the bootloader now...
Pls help
xpxj said:
What happen when your not CID unlocked? I had removed my hardspl before I tried to again flash a rom. I am stucked with the bootloader now...
Pls help
Click to expand...
Click to collapse
Only Official stock rom or the wizard_love rom will get flashed,no other wm6 rom is possible.
Hello,
I have this rom : RUU_Trinity_LVSW_WWE_1.25.0.8_GPS (AKU 3.5.2)
from http://forum.xda-developers.com/showthread.php?t=302198
I wanted to test the new WM6 roms, unfortunately, my trin doesn't update with any rom I tried (Orange, HTC, LVSW Wm6, Mun_Rus Wm6, ...)
It tells me : "ERROR 262 : UPDATE ERROR
... communication error during the process"
I'm stuck on LVSW Wm5 rom :'(
Not sure if Des SPPL is causing this problem... anyway, I tried to update it from Bootloader or synched, on XP and Vista, 5 differents roms... no luck.
I would really appreciate some help, thanks
can you list the steps of what happened, in order?
also, just to make sure i understand, have you already tried to manually enter the bootloader and THEN run the RUU? *edit* one last question, have you tried this.. after the error, leave your device connected and in bootloader, then restart the RUU.. can you give me your device details too?
Well, when I run the update with normal step (connect AS, then launch update...) when the update is ready to be started (progress bar appears), phone have to switch to bootloader, which it does. However, it seems that the RUU is waiting for that since it return me this error:
ERROR 246 : Device not responding
And I have to exit. I don't understand ?
Progress bar didn't even appear on the phone.
At this time boot loader shows
IPL-SSPL by Des
SPL-1.07.ds
So since I'm already in Bootloader mode, i try to launch RUU again. Here is the error I get when the progress bar appears on both phone and PC :
ERROR 262 : Update Error
And it offer me to recover the device, which I don't need as the current rom has been left untouched and is still functionning after the error.
Then I reset the device to enter bootloader this time:
IPL-0.50
SPL-1.06.0000
same error : ERROR 262 : Update Error
I'm kinda out of option, thanks a lot for your help !
well, it's been a pretty common thing for the RUU to give an error when the device goes in to bootloader (can't detect it for some reason). Most times, simply running the RUU again while the device is still in bootloader works fine.
Why don't you put hard-spl on just in case, manually enter bootloader (which will then be hard-spl) and run the RUU again. You shouldn't enter the bootloader manually unless you've loaded hard-spl or sspl on to your device. From what i understand you won't be successful from what you did after the hard reset. When your phone went in to bootloader the first time, it was with SSPL pushed to your device by the updater program to enable you to update safely. After resetting, you're back to your normal bootloader which won't help anything.
I know one time it did this to me, and wouldn't connect to my device. I started the RUU about 3 times in a row with my device on bootloader, and for some reason after the 3rd time it suddenly worked.. weird, i know.
anyway, hard-spl will make the whole process safer.. let me know if it connects or not, i'll see if i can help you troubleshoot
I wanted to install hard-spl, but it runs as a normal RUU and give me exactly the same errors as a normal run update (error stated above).
So I don't see how I could install it
Another thing weird, when I run a official HTC rom update, when the udpdate should start (device enter in boot loader, progress bar appear in bot PC an device), the Trin reset itself and boot as normal... of course the RUU gives an error due to this reboot ...
Same weird behavior with an official Orange rom...
Now I'll try with SSPL...
Oh and thanks a lot for your help
simply try to run twice ROMUpdateUtility.exe after error
Please read carefully what I have posted (and the steps I ran into)...
Already launched again RUU, it gives me an Update Error and the device is stuck on the screen that show the progress bar.
Need to soft reset... I can't launch again the RUU after that since the device is no longer recognised as connected on PC.
I confirm I can't manage to install the Hard SPL, even after laoding Des sspl from the device...
Defintly blocked
At last I have succeeded in upgrading the device. Seems like my bootloader was somehow corrupted or something... after doing another Hard Reset it have installed hard spl succesfully...
I had already done a hard reset before, so I don't understand what happened.
Nevermind, at last i can try wm6
thanks a lot for your help racerx_ anyway
hey no problem.. not sure that i actually helped haha.. but i'm glad you sorted it out. happy flashing!
Might it have been the USB driver on the desktopside ?
Did you see XP recognize and install HTC USB device again, after device disconnecting from AS and going into bootloadermode for first time ?...
Just a thought...
Not sure what it is, but it's happening again, can't update anything as the bootloader seems somehow corrupted.
When i enter bootloader it briefly display the 3 color, then grey screen with "loading" and then the hard spl screen from Olimpo... the only problem I see is that it does no longer display TRIN100, but only little dots (like if it was corrupted)...
Very annoying situation, and I have already done some hard reset, but nothing
So more exactly, where I start DES SSPL or when I enter Olipro Hard SPL (that I installed before WM6), it shows the good infos like :
TRIN100
xxxx
TRIN100
SPL-
But after 1/4 of second, it start loading for a very short moment
and display again the RGB screen with the infos except the "TRIN100" parts are like this ':':':':':':
Anyone has seen this before ???
@cedrick: You have a SD card inserted on this device, right? if so, remove the SD card and try again.
If the SD card is not the problem, then you might have overwriten the memory region where the ModelID is stored. I can help you to recover it if that is the case.
pof said:
@cedrick: You have a SD card inserted on this device, right? if so, remove the SD card and try again.
If the SD card is not the problem, then you might have overwriten the memory region where the ModelID is stored. I can help you to recover it if that is the case.
Click to expand...
Click to collapse
...... well well, that was simple hahaha (and I feel stupid lol).
yes I had my SD inserted (and I remember only now that the last time it worked I had indeed removed the mini-SD).
So, thanks to you I have understood this issue at last !
Muchisimas gracias por tu gran ayuda pof
Now the question is, wtf do u have on this SD card? LOL
Errr that's a good question... maybe it is time to clean those 4go of things (which most of those come from the SD I had on my Prophet, in the top of that)
Anyway, it's a rare specimen indeed... want a copy to play with heh ?
i need some serious help im desperate at this stage.
ive basically got a htc tytn ii on uk orange
i update the rom to htc standard one which sim locked it
i followed the instruction on how to get it like i got it from orange
which i believe was sucessful. but because it was still sim locked i
thought the hardspl was relocked so i ran that again which failed and ended up on the tri colour screen after which i tought it may still be hardspl locked
so i tried to flash it with the rom again it got to 17% then crashed
now my phone will only boot to the tricolour screen it wont load activesync and if i try a flash it with anyrom it either stays at 0% gets stuck or gets to 1% then the phone restarts.
ive buggered the phone up proper i need some help if there is any for this mess
when i try a rom upload it says error [294]: invalid vender id
this update utility cannot be used for your pda phoe please check your update utility
Did you install Hard SPL?
http://forum.xda-developers.com/showthread.php?t=334679
See if you can install that and then try to reinstall your rom.
this required activesync to be green mine will respond to usb but not activesynce so i cant go any further with the hardspl unlock im stuck on the tricolour screen. and flashing will only go to 1% then restart and the message come up again.
same problem
i have the same problem and i can only get to 1% . i have tried to flash it with several roms using diferent utilities and none seem to work i used hard spl the first time when it failed. HELP PLEASE !!!!!!!
found solution
got mine working here is what i did
run mtty select usb after disabling it in activesync
press enter and you should see cmd>
type boot and when your device restarts it should start in your old rom
run hardspl again
then you need to reinstall your rom
although a word of warning my phone became sim locked after this
worked a treat many thanks it is sim locked just have to wait for the sim unlock for it now
willbyrne said:
got mine working here is what i did
run mtty select usb after disabling it in activesync
press enter and you should see cmd>
type boot and when your device restarts it should start in your old rom
run hardspl again
then you need to reinstall your rom
although a word of warning my phone became sim locked after this
Click to expand...
Click to collapse
no worries
yeah no worries, i was affraid when i locked mine i might have to return it and get anothe orange version but i used some company online and got my code in about 3 days.
oh yeah you will probably need to enter the code in twice, mine said simlocked and then network locked but it was the same code
After I get out my diamond from my pc and than turned off it cannot start, it stoods on screen when it shows me version of my radio and ROM. I know that I have to do hard-reset but i dont want to, because i were so dumb that I dont backed up my mdata and programs which Ihave installed in Memory. Is there any chance to turn it on without the hard-reset???
Thx in advance.
betacheer said:
After I get out my diamond from my pc and than turned off it cannot start, it stoods on screen when it shows me version of my radio and ROM. I know that I have to do hard-reset but i dont want to, because i were so dumb that I dont backed up my mdata and programs which Ihave installed in Memory. Is there any chance to turn it on without the hard-reset???
Thx in advance.
Click to expand...
Click to collapse
do you mean bootloader (Tri-Coloured Sceen) Or the splash screen (Black Screen with touch diamond on it)?
I suggest you do a hard reset, and check this thread on how to easly back up ur programs, settings and manila config for future use using SASHIMI
http://forum.xda-developers.com/showthread.php?t=538513
Stuck in Bootloader screen
Whlie trying to upgrade the ROM on my Touch Diamond something happend so i got an error and the upgrade stopped. Now i cant continue the upgrade becouse my pc wont recognize the phone when i connect it with the usb-cabel. When i try to run the upgrade again i just get an error saying that there is something wrong with the connection.
I have tried hard reset but nothing works.
Hope someone can help me with this problem.
Thanks
/Kenneth
KenOslo said:
Whlie trying to upgrade the ROM on my Touch Diamond something happend so i got an error and the upgrade stopped. Now i cant continue the upgrade becouse my pc wont recognize the phone when i connect it with the usb-cabel. When i try to run the upgrade again i just get an error saying that there is something wrong with the connection.
I have tried hard reset but nothing works.
Hope someone can help me with this problem.
Thanks
/Kenneth
Click to expand...
Click to collapse
i think I am in same situation. phone is bricked :/
I dont think your phone is bricked, put your phone into bootloaded mode, connect phone to pc and flash the nbh file using CustomRUU. That should fix things
Dom1n8tr1x said:
I dont think your phone is bricked, put your phone into bootloaded mode, connect phone to pc and flash the nbh file using CustomRUU. That should fix things
Click to expand...
Click to collapse
each bootloader i have tried using the different hard spl version gets as far as the progress bar but fails at 0% with 262 connection error. tried about 6 different hard spl, signed unsigned olinex, customRUU. each of them all fail at 0% of progress bar.
will try it again today.
sorry betacheer for the hijack, but hope this helps you out in some way too.
Hi,
I'm having a problem with CID-Unlocked. I've a branded MDA Vario III and some person tried, without unlocking, to upload a new firmware.
I can't come into wm6 cause it stalls after the startup logo is displayed. If trying the original rom the famous 270 corrupted error will be displayed (after 1%)
Also it looks like the kaisdiag/kaisimg on SD won't work, it stalls on the "Loading..." screen, or am i doing something wrong? The only place I could go is the tri-colour screen.
Any suggestions?
BommelDingNL said:
Hi,
I'm having a problem with CID-Unlocked. I've a branded MDA Vario III and some person tried, without unlocking, to upload a new firmware.
I can't come into wm6 cause it stalls after the startup logo is displayed. If trying the original rom the famous 270 corrupted error will be displayed (after 1%)
Also it looks like the kaisdiag/kaisimg on SD won't work, it stalls on the "Loading..." screen, or am i doing something wrong? The only place I could go is the tri-colour screen.
Any suggestions?
Click to expand...
Click to collapse
What does it say on the tri-color screen when you plug in to the PC.
First on the TRI-Colour i see is:
Serial and after plug the usb it says USB
BommelDingNL said:
First on the TRI-Colour i see is:
Serial and after plug the usb it says USB
Click to expand...
Click to collapse
Flash Hardspl then and after that flash to any rom you want. Click under my signature and read carefully of how to flash and if you want to keep your tilt warranty
Let me say that the warranty has allready been void.
However, all the time busy with jumpspl, currently with error 00068002. Tried with the original file from the provider. Didn't get stuck with this one but restarts himself.
I was allready trying lots of stuff, but still fails.
Which hardSPL would you suggest? Cause I allready tried:
HardSPL-3.07
HardSPL-3.56-force-USB
HardSPLv1
Still with no luck.
BommelDingNL said:
Let me say that the warranty has allready been void.
However, all the time busy with jumpspl, currently with error 00068002. Tried with the original file from the provider. Didn't get stuck with this one but restarts himself.
I was allready trying lots of stuff, but still fails.
Which hardSPL would you suggest? Cause I allready tried:
HardSPL-3.07
HardSPL-3.56-force-USB
HardSPLv1
Still with no luck.
Click to expand...
Click to collapse
3.34 Daveshaws and 3.29 try those.
I Tried 3.34, renamed to kaisimg.nbh, but the loader gets stuck on Loading... and that's it.. all the teme.
Even with 3.29.
BommelDingNL said:
I Tried 3.34, renamed to kaisimg.nbh, but the loader gets stuck on Loading... and that's it.. all the teme.
Even with 3.29.
Click to expand...
Click to collapse
Did you tried this http://forum.xda-developers.com/showthread.php?t=375583
won't work, but even tried it:
"YOUR DEVICE MUST BE IN CE AND SYNCED BEFORE RUNNING EACH STEP."
First time on my pc..
BommelDingNL said:
won't work, but even tried it:
"YOUR DEVICE MUST BE IN CE AND SYNCED BEFORE RUNNING EACH STEP."
First time on my pc..
Click to expand...
Click to collapse
I'm assuming that you already tried to hardreset your device right
Additional:
When using Kaiserunlocker I get stuck at 0% with the following error: Error 262..
Just took to long, i guess.
gmaniac2008 said:
I'm assuming that you already tried to hardreset your device right
Click to expand...
Click to collapse
I did.. several times
BommelDingNL said:
Additional:
When using Kaiserunlocker I get stuck at 0% with the following error: Error 262..
Just took to long, i guess.
I did.. several times
Click to expand...
Click to collapse
http://forum.xda-developers.com/showthread.php?t=423486
Running all progs as admin?
Allways.. in win7 UAC is turned off and win xp pro, no limitations.