Unable to start data connection! - Tilt, TyTN II, MDA Vario III General

For some strange reason Kaisertweak continues to 'reset' itself to disable my data connection.
I have made a simple video that shows I am on E connection only, 3G is off, as well as Data Connection.
I launch Kaisertweak to enable the Data (GPRS/EGDE/HSDPA/WIFI) tab. As a good measure I verify that the others are enabled as well.
The following screen shows one of the errors I am receiving - stating This programs requires a data connection, and will retry automatically. In the mean time, please check your signal strenght. (Error: wininetHttpError [0 12150]0)
As you can see on the ssame screen I am at full signal strength.
I have enable my data connection through Kaisertweak and reconnect to google maps to use a random search in order to start the data connection.
Searching....
Searching....
Searching....
Again - This programs requires a data connection, and will retry automatically. In the mean time, please check your signal strenght. (Error: wininetHttpError [0 12150]0)
I launch Kaisertweak again and my Data (GPRS/EGDE/HSDPA/WIFI) 'tab' is back to disable. I reenable the connection by using the pulldown.
Exit Kaisertweak and do a random search using google maps.
Searching....
Searching....
Searching....
Same error as above.
I launch the comm manager and enable 3G.
Once 3G is enabled I try to complete the random search though google maps.
Searching....
Searching....
Searching....
You will note that 3G does not connect during this search. As soon as it erros out with the same error as listed it connects to H.
I retry the search...
Searching....
Searching....
I check connectivity and although connected to H I see no active data sessions.
Searching....
This programs requires a data connection, and will retry automatically. In the mean time, please check your signal strenght. (Error: wininetHttpError [0 12150]0)
I did relaunch Kaisertweak again and my Data (GPRS/EGDE/HSDPA/WIFI) 'tab' is back to disable.
any ideas?
I need my data!! haha!! Please see attached!
You may need to pause the video at some parts to see what happens since the screens flash pretty fast at some parts.
YOUTUBE VID

Silly question, but does a soft reset not fix....?
Do you get the same issue if you try to launch IE?

brandall said:
Silly question, but does a soft reset not fix....?
Do you get the same issue if you try to launch IE?
Click to expand...
Click to collapse
I did do a soft reset and I was able to use my data connection for one use. Meaning after the 30seconds on nonuse it would automatically turn off as per settings in Kaisertweak.
Then I was back to the same issue as listed above.
Again soft reset, I am able to use my data connection via IE and other apps that require data, however, after the 30 seconds of nonuse the same issue occurs as listed above.
Initially I thought it was something wrong with the build. So I did reflash the phone, I did download and use a newer version of Kaisertweak.

Remove post sorry read wrong....

This is a strange one my friend. Try the ATT settings cab just for Shnitz and giggles. Also, how about you try manually disconnecting the data before Tweak has a chance, are you able to reconnect after that?

after some trial and error -
I deleted kaisertweak and associated files. Soft reset the phone. My phone is back to normal. I am able to use my data. I can manually disconnect from H and then launch IE and my data connection starts up fine. I am still unsure why Kaisertweak would default to DISABLED for data although I set it to ENABLE. I am just glad to have my data connection back without having to soft reset when I wanted to use it.
To those that have replied... thanks for your feedback.

usachftp said:
after some trial and error -
I deleted kaisertweak and associated files. Soft reset the phone. My phone is back to normal. I am able to use my data. I can manually disconnect from H and then launch IE and my data connection starts up fine. I am still unsure why Kaisertweak would default to DISABLED for data although I set it to ENABLE. I am just glad to have my data connection back without having to soft reset when I wanted to use it.
To those that have replied... thanks for your feedback.
Click to expand...
Click to collapse
The screen shot you displayed was for the fast sleep settings
Your data settings should look as displayed below
Sounds as if you had the "Disconnect After" set to 30 seconds

Related

gprs using data when trying to connect...

i was in an area with no gprs today and my kaiser was constantly trying to connect, this went on unnoticed and when i looked at my gprs tracker is racked up 38mb in one hour, thank god i have a 1gb data plan. what's going on here why does it use data to connect? and is there any way to stop it from trying to repeadily connect like that? when i try to turn off the gprs connection with comm manager or gprs manager, windows will automatically try to reconnect over and over and over again.
Any chance you have ActiveSync running in the background when you check? I'm abroad at the moment and have the same problem, this is my no.1 culprit at the moment.
nope i have nothing running in the background. i don't understand how it's using data when it's not connected. i can't figure this out, i don;t even know where to begin.
sorry double post
I have the same issue! I have no data plan and my GPRS was connected for some 39 minutes the other day!!!
Anyone any ideas? Not sure if it's the MMS messaging that is causing it...?!?
figured it out, i just left the password section blank in the connection setting that was it always promts me to enter the password everytime the phone tries to reconnect

Data connection never drops

I was away for a week and upon returning my Tilt is exhibiting some strange behavior that's different from before.
Basically, data connections never drop. So once the first ActiveSync, use of Pocket IE, etc, occurs, the connection stays on forever. For example I just checked my phone and the connection has been active for over 16 hours (the phone sat hibernated for most of that time).
I could have sworn that previously, the connection would drop after some period of inactivity. The little H with the signal strength on the title bar would change back to the triangle antenna. But no more. I tried with HSDPA off too and saw the same problem (except I got a little 3G instead of a little H above the signal bars).
I even hard-reset my Tilt and this did not fix it.
What can explain why my data connections used to drop on their own before but suddenly stopped doing so? Basically, my phone used to behave as if the "disconnect after" KaiserTweak was enabled (even though I never enabled it) but it's now behaving as if "always on" is enabled (even though it is not enabled).
So you know about Kaiser Tweak - have you loaded Kaiser Tweak and set the setting? and it still behaves this way?
I cannot explain it - but if Kaiser Tweak fixes it do you still need an explanation?
Bill
whk said:
So you know about Kaiser Tweak - have you loaded Kaiser Tweak and set the setting? and it still behaves this way?
I cannot explain it - but if Kaiser Tweak fixes it do you still need an explanation?
Bill
Click to expand...
Click to collapse
I agree with Bill... If You have a solution that will work even though you haven't had to use it before, why not fix the problem a new way instead of Dwelling on the problem.
Maybe Check this. In Phone Goto Menu -> Data Tab. Check your Check Box on Disable data connections when device enters Sleep Mode. Soft Reset and see if that will fix it for you.
Thanks for the suggestions guys.
I didn't want to fix this with the KaiserTweak because it comes with a disclaimer that (a) it might not work with all programs and (b) is might prevent simultaneous voice and data calls. The latter seems more problematic; maybe this is not an issue with 3G/HDSPA (and only with the older data technologies)?
I can't find a data tab anywhere. I have a Tilt with stock ROMs... is the menu and data tab available somewhere? I'd like to try that suggestion.
tai4de2 said:
Thanks for the suggestions guys.
I didn't want to fix this with the KaiserTweak because it comes with a disclaimer that (a) it might not work with all programs and (b) is might prevent simultaneous voice and data calls. The latter seems more problematic; maybe this is not an issue with 3G/HDSPA (and only with the older data technologies)?
I can't find a data tab anywhere. I have a Tilt with stock ROMs... is the menu and data tab available somewhere? I'd like to try that suggestion.
Click to expand...
Click to collapse
If you don't have that tab the option has been "hidden" by the ROM Makers. So Though there is a way to get to it, It is One I don't know.
I would suggest then getting Schaps Advanced Config, Is what I use to put my Data Connections to off after three minutes. I haven't had any problems with simultaneous lovin' with Voice and Data.
Well I turned on the KaiserTweak for this and it works. Maybe I had it enabled before and didn't realize.
One thing I notice is that I always get the "connecting to" balloon pop-up when a connection is being established, even if I tell it to hide. So there's one annoyance, but it's better than having my battery drain down due to the constant connection.
Interestingly this never drop behavior coincided with the switch-over from the behavior of the 3G icon that goes to H only when a connection is established, to always showing the H icon. Could these 2 behaviors be connected somehow, and due to a change on AT&T's side?
You can turn off the notification by going to settings -> sounds and notifications -> notifications tab ->event = connection established, uncheck "display message on screen".
I was just experimenting and I found that enabling the "disconnect after" KaiserTweak prevents simultaneous voice and data. If a voice call is going, I cannot establish a data connection and if a call comes in the data connection drops. If the KaiserTweak setting is not enabled, I can get simultaneous voice and data.
My phone always shows the H icon.
It seems I have to choose between the stock setting of "connection never drops, and drains battery" and the KaiserTweak setting of "can't get simultaneous voice and data connections". Ouch!
Does BandSwitch use a different way to handle forcing the disconnections, or is going to boil down to the same registry setting that KaiserTweak uses for this?

Disconnect data connection

Hi,
Anyone know how to set so the data connection will be disconnected automaticaly if there is no activity after certain times?
gogol said:
Hi,
Anyone know how to set so the data connection will be disconnected automaticaly if there is no activity after certain times?
Click to expand...
Click to collapse
there might be a program for this however you can also use the built in function in your phone. If you go to settings.. click phone and than go to the data tab and check the box that says "disable data connection when device enters sleep mode". This way everytime you press the power button to turn screen off data connection will disconnect or whenever device automatically enters sleep data will disconnect.
Kaiser Tweak
has an option that u can set to automatically disconnect a data session after a certain amount of inactive time
Open up your REG editing software
Navigate to (HKLM>Comm>ConnMgr>Planner>Settings)
Click on (SuspendResume)
Change Value Data to: GPRS_bye_if_device_off
Click OK
Soft Reset
By changing this value, your phones data connection will automatically disconnect after closing an app that uses your data connection about 30sec-1min, or if your phone goes to sleep. Whichever comes first.
Be warned though that some programs for some reason are not visible as keeping an active GPRS connection so it will disconnect while in use. THe only one that I encountered was youtubeplay. After about a minute, the video was freezing and I didnt know why. Well it was because my phone was automatically disconnecting. So before I would use youtubeplay I would just open skyfire then minimize it to keep the connection open. Youtube play was the only program that I found had this problem.

How to stop internet connection

A silly question by a new user: how is it possible to stop an internet or data connection (no matter if hsdpa, edge, gprs) once started?
Thanks
use 'long key press' in settings, can be set to disconnect a data connection (sdpa, edge, gprs)
Use this program:
http://rapidshare.com/files/173250379/GPRS...onnect.CAB.html
The connection stop after 1 minutes of inactivity
jack1985 said:
Use this program:
http://rapidshare.com/files/173250379/GPRS...onnect.CAB.html
The connection stop after 1 minutes of inactivity
Click to expand...
Click to collapse
faulty url!
take this one:
GB-SOFT GPRS-UMTS_Tweak_WM6.1_Diamond
there you can choose the idle-time for disconnect
Anyway the manual stopping mode is to tap the bar that is on the top of the sceen...than tap the G E 3G or U icon and so you can tap disconnect.
Poker85 said:
Anyway the manual stopping mode is to tap the bar that is on the top of the sceen...than tap the G E 3G or U icon and so you can tap disconnect.
Click to expand...
Click to collapse
Cool, also in stead of holding the end call button, wich locks the phone in my case,
Dubbelclicking the end call button alse ends my edge connection.
In order for your end key to stop the connection, you have to go to Settings>System>Long Press End Key>Select Terminate data connection
Then when you press and hold your end key, it will end the connection
if you prefer to stop internetconnection by shortcut, try VJKeyPress.exe 126
this one toggles internet connection
i've searched and i've searched and i cant find the resolve!
after retrieving hotmail, the connection stays active, meaning bars are lit up. for HOURS after unless i long-press-end key or something like that. even when i am surfing the web, after a page is fully loaded, the bars stay lit. on my old diamond, the bars used to go gray or "dormant" etc. therefore no tweaks i have found help (i.e. most operate with this rule "if the connection is dormant/inactive for xx minutes, turn off data" etc. well my connection remains ACTIVE unless i manually intervene)
what is causing this??? i only have spb mobile shell and spb phone suite installed. stock ROM.
hello? anyone? NO one is having the same issue or can help with this??? at this point i'd even be happy with a rude comment about how i should learn how to search coupled with a few links to threads which contain the answers! :\
I'm not sure I understand your question.
You're saying the connection stays alive after using mail or opera?
By default, WMo does not turn off data connection, so once you've made a data connection, it stays on.
Now, there are lots of programs out there that turns off data connection after a pre-set time. If you have Advanced Config on your Diamond, it's somewhere in there as well (I use SKTools and not Advacned Config so I can't point you exactly where, but it's there)
That said, many have tested battery drain and find that leaving the data connection ON or OFF makes absolutely no difference on the battery drain. It's only when you're transmitting data that drains more battery. Not sure if that's where you're coming from to want to turn off data connection
number16 said:
I'm not sure I understand your question.
You're saying the connection stays alive after using mail or opera?
By default, WMo does not turn off data connection, so once you've made a data connection, it stays on.
Now, there are lots of programs out there that turns off data connection after a pre-set time. If you have Advanced Config on your Diamond, it's somewhere in there as well (I use SKTools and not Advacned Config so I can't point you exactly where, but it's there)
That said, many have tested battery drain and find that leaving the data connection ON or OFF makes absolutely no difference on the battery drain. It's only when you're transmitting data that drains more battery. Not sure if that's where you're coming from to want to turn off data connection
Click to expand...
Click to collapse
number16, my savior! i'll try to explain as best i can: when the data connection is started/being used, those left-right arrows appear above the signal strength, correct? what i call "active" is when those arrows are lit (presumably when data is actually being transferred). what i call "dormant" is when the arrows are still there but are gray/not lit (i.e. connection is still open, but not currently transferring data). well, up until a 2 wks ago, all seemed fine - the arrows would briefly stay lit when downloading a page, connecting to hotmail, etc, but then would go gray once the transfer was complete. now however, the arrows stay lit. sometimes for hours at a time even tho nothing is running, no data (that i know of) is being transferred, etc.
so what i was saying is that, yes, i know i can long-press-end key to shut it down, but that only works if i notice it otherwise it's just draining my battery. (most times it is in my pocket, and since it checks hotmail periodically, the data connection may open and stay on without me noticing). and yes, i know about advanced config setting (and actually, i DO have it set to turn off after a minute) BUT that only applies if "connection is not active for more than a minute". i.e. since my whole problem is that my data connection technically stays active, that advanced config setting doesnt work.
so my question is, what is keeping the connection active? why is it doing this? i am running stock ROM and only have spb mobile shell and spb phone suite loaded. and a few other minor tweaks via advanced config/regedit. i even tried spb wireless monitor to see what was active after a data transfer was complete (as far as i could tell) but it didnt really tell me anything.
does all that make sense?
thanks for any help you can provide...

Unable to turn off Tilt data connections

I am unable to turn off current data connections on my Tilt. I'm using MoDaCo's "No Data". So I decided to try shutting off data connections with KaiserTweak. I'd set the Data connections to disabled but data still comes thru. When I try to shut if off with NoData I get this message "Connection disabled. You will need to manually duscinnect if a GPRS connection is currently active". Anyone know whats goin on here?
Anyone? Anyone? Bueller?
You could always go into settings ---->connections----->connections----->manage connections and delete anything there..... it cant connect if it doesnt know what to connect to................
I'm not looking to completely delete it. I just want to be able to disable it when I'm around WiFi.
FuSchnickens said:
I am unable to turn off current data connections on my Tilt. I'm using MoDaCo's "No Data". So I decided to try shutting off data connections with KaiserTweak. I'd set the Data connections to disabled but data still comes thru. When I try to shut if off with NoData I get this message "Connection disabled. You will need to manually duscinnect if a GPRS connection is currently active". Anyone know whats goin on here?
Click to expand...
Click to collapse
correct me if I'm wrong, NoData is only to disable data connections before it connects.
so if U already have a data connection (not WIFI) active, U need to disconnect the data connection first.
After that, your tytn will not be able to turn on the data connection unless U "enable" the settings in NoData.
hope it helps.
oriki said:
correct me if I'm wrong, NoData is only to disable data connections before it connects.
so if U already have a data connection (not WIFI) active, U need to disconnect the data connection first.
After that, your tytn will not be able to turn on the data connection unless U "enable" the settings in NoData.
hope it helps.
Click to expand...
Click to collapse
I'm not familiar enough about NoData to know if it only disables a data connection before connecting or not. Sometimes when I connect I get the pop up window saying I'm connecting. Other times I don't. There's usually a big "3G" up at the top of the phone and when I connect I gt a little "3G window.
FuSchnickens said:
Anyone? Anyone? Bueller?
Click to expand...
Click to collapse
Noob here but....I used Kaisertweaks and it blocks GRPS for me.
torp74
When I try to do it thru KaiserTweaks I set it to Disable. When u disable yours does it say enabled or disabled when in Kaisertweaks? Does anyone at all know what going on here?
FuSchnickens said:
When I try to do it thru KaiserTweaks I set it to Disable. When u disable yours does it say enabled or disabled when in Kaisertweaks? Does anyone at all know what going on here?
Click to expand...
Click to collapse
Mine says disabled. I pretty much set everything under "data" to disable. I'm in a wifi paradise so screw att.
torp74
In connections I set it under one without any settings. Its been working for me so far. When I DO want to connect I just switch it back to medianet. Everything else works as normal.
Even when I change it to disabled it continues to say enabled under settings? I've even tried to reinstall Kaisertweaks but still get the same results. Has anyone else come across this problem? This is getting frustrating.

Categories

Resources