How to flash HTC DIAMOND ? - Touch Diamond, MDA Compact IV General

I have htc diamond which is dead and need to flash it plz. Tell me from where i get its rom and how to flash it?
Plz. Help
regards

Read this....
http://forum.xda-developers.com/showthread.php?t=416211
It should help. Good luck.
Will

ajaysehgal said:
I have htc diamond which is dead and need to flash it plz. Tell me from where i get its rom and how to flash it?
Click to expand...
Click to collapse
WHat do you mean dead ? Can you get to the bootloader?
Before you do anything if you haven't already, flash your device with
a hard-spl ....http://forum.xda-developers.com/showthread.php?t=400950
and then look here for
a rom.....http://forum.xda-developers.com/forumdisplay.php?f=430

Can't get to the boot loader
I have the same problem. I have a dead HTC diamond, when i insert the battery, it vibrates, gives me a sound and just keeps turning the backlight on and off... HELP ME

Bootloader
band27 said:
WHat do you mean dead ? Can you get to the bootloader?
Before you do anything if you haven't already, flash your device with
a hard-spl ....http://forum.xda-developers.com/showthread.php?t=400950
and then look here for
a rom.....http://forum.xda-developers.com/forumdisplay.php?f=430
Click to expand...
Click to collapse
I am faced with the same problem. I get the Touch diamond screen the the red R G D numbers in the bottom right corner and its frozen so how th flash the ROM? I do know the Rom is the problem because I know the Bozo that tried to flash the "Android" rom to it.

Iron_Dingo said:
I am faced with the same problem. I get the Touch diamond screen the the red R G D numbers in the bottom right corner and its frozen so how th flash the ROM? I do know the Rom is the problem because I know the Bozo that tried to flash the "Android" rom to it.
Click to expand...
Click to collapse
Just follow the instructions above. Follow them to the letter. If you don't you will mess things up more. Flashing Roms etc is a very easy but very strict process. You have to follow to the letter. I have been doing this for 10+ years! I am no technical expert but do follow the cooks instructions...
There are loads and loads and loads and loads and loads and threads on this and where you are. You may have to look a bit harder as the Touch Diamond is an old phone. I personally still use it as a dongle. It works really well and does not install loads of rubbish superfluous software!
Good luck....
Will

Related

** Urgent ** my Wizard cant power on after upgrade ROM

Hi to all that can help me, i just flash the rom yesterday night that i have download and its completed the upgrade and go into the screen and running the installing of the program that come with the rom.
after the full install and the device restart without any more power and picture show.
I have try to charge the battery with wall charger and also replace with new battery but still no power.
Is that mean i'm flashing with a wrong rom and what should i do now.
Can i get it fix?
nicholas99 said:
Hi to all that can help me, i just flash the rom yesterday night that i have download and its completed the upgrade and go into the screen and running the installing of the program that come with the rom.
after the full install and the device restart without any more power and picture show.
I have try to charge the battery with wall charger and also replace with new battery but still no power.
Is that mean i'm flashing with a wrong rom and what should i do now.
Can i get it fix?
Click to expand...
Click to collapse
That really sucks...
nicholas99 said:
Hi to all that can help me, i just flash the rom yesterday night that i have download and its completed the upgrade and go into the screen and running the installing of the program that come with the rom.
after the full install and the device restart without any more power and picture show.
I have try to charge the battery with wall charger and also replace with new battery but still no power.
Is that mean i'm flashing with a wrong rom and what should i do now.
Can i get it fix?
Click to expand...
Click to collapse
which rom did u flash it with ??? wat ver ur configs before that . ur ipl/spl version os and etc.
sometime it happens that the power button doesnt works ....
try poking the reset button wiz ur stylus ... press and hold for sumtime and c wat happens
if it starts then ... press it again and wen the screen goes blank pree the camera button and hold it ... ull get into the bootloader ... den connect da usb and flash a new rom or da old factry one ...
i use molski's rom its really stable
well i'm using Wizard_Love_2.26.10.2_WWE_Novii+CF2 for the first but after that i just try to flash the rom the the chinese support rom which is Dopod_CHT_TW_RUU by using the newromupdateutility to flash it to my phone. At the beginning the rom flash successful and login to the device for install all the program that come with. After all the installation done the device will restart but never boot up anymore even u can see any green light flashing at all. Please dont tell me i damage my rom, should i send for repair?
or someone can help me out please......
nicholas99 said:
well i'm using Wizard_Love_2.26.10.2_WWE_Novii+CF2 for the first but after that i just try to flash the rom the the chinese support rom which is Dopod_CHT_TW_RUU by using the newromupdateutility to flash it to my phone. At the beginning the rom flash successful and login to the device for install all the program that come with. After all the installation done the device will restart but never boot up anymore even u can see any green light flashing at all. Please dont tell me i damage my rom, should i send for repair?
or someone can help me out please......
Click to expand...
Click to collapse
did u try da soft reset ???
yes i did but nothing happen at all
Xda Neo
I have the same problem. IPL and SPL 2.15.00001 and tryed to downgrade but after restart it does not power on. Tried everything but no way to power on. Is somebody know how to make it work again.
Regards,
You guys tried to flash a G3 Rom on your G4 Wizard.
So your bootloader (IPL/SPL) that is 2.xx.0001 is overwritten by a G3 bootloader that is 2.xx, so in other words....your devices are bricked.
Please someone, correct me if I am wrong.
Molski
yup, I agree. Bricked hopefully someone can fine the JTag on these devices.
Wow that sucks! Full moon over Miami last night, naw that can't be it .....
Sorry but unfortunately I must follow my Grandmother's advice concerning when I don't have anything nice to say...
R there NO ALTERNATIVE WAY for THIS?? HOPE we can help those people that made a mistake by upgrading to a ROM that doesnt fit to their WIZARD. due maybe because of TOO XCITEMENT they forgot to CHECK FIRST(PLS! ALWAYS CHECK FIRST) their IPL/SPL.
HOPE those master GURU's can do something!
So, please someone tell clearly how to know G3 or G4 of the Wizard
thanks so much
Sorry but I have no more tolerance for people who just jump in first without doing a little research. A while back when the G4 first came out we didn't know. Now everyone who puts out a ROM warns people about the possible consequences. And there's so many threads on just the first page with tales of woe... how can a person miss them all??
I'm sorry but my parents raised me to take responsibility for my own actions, as Baretta used to say" Don't do the crime if you can't do the time"
Similar to when a Cat 4 hurricane is coming at you and you don't leave after being warned.... then blaiming everyone but yourself...
And if anyone wants to rebute me on this, don't bother as I've neither the time nor the patience.
Bottom line is that flashing phones has the very real possiblity of trashing an expensive piece of hardware in a very short period of time. If one has any doubts, then they shouldn't do it! And if a person doesn't have a concern initially then they're asking for trouble.
Sorry....
magicer said:
So, please someone tell clearly how to know G3 or G4 of the Wizard
thanks so much
Click to expand...
Click to collapse
a G4 has a .00001 on the initial splash screen.
ArtXT said:
R there NO ALTERNATIVE WAY for THIS?? HOPE we can help those people that made a mistake by upgrading to a ROM that doesnt fit to their WIZARD. due maybe because of TOO XCITEMENT they forgot to CHECK FIRST(PLS! ALWAYS CHECK FIRST) their IPL/SPL.
HOPE those master GURU's can do something!
Click to expand...
Click to collapse
The problem is that if your bootloader (IPL/SPL) is fuc*ed up, there is no way to get it in bootloader mode to do a flash!
Only known solution is with JTAG connector, but that solution is not a clear solution yet, but I dont know nothing about that solution (simply...because I never needed it).
Molski
Dr Puttingham said:
Sorry but I have no more tolerance for people who just jump in first without doing a little research. A while back when the G4 first came out we didn't know. Now everyone who puts out a ROM warns people about the possible consequences. And there's so many threads on just the first page with tales of woe... how can a person miss them all??
I'm sorry but my parents raised me to take responsibility for my own actions, as Baretta used to say" Don't do the crime if you can't do the time"
Similar to when a Cat 4 hurricane is coming at you and you don't leave after being warned.... then blaiming everyone but yourself...
And if anyone wants to rebute me on this, don't bother as I've neither the time nor the patience.
Bottom line is that flashing phones has the very real possiblity of trashing an expensive piece of hardware in a very short period of time. If one has any doubts, then they shouldn't do it! And if a person doesn't have a concern initially then they're asking for trouble.
Sorry....
Click to expand...
Click to collapse
I knew I have a G4 and can't upgrade/downgrade with G3 roms or even change IPL/SPL, but I did that :]
Just found ROM v2.22.1 (I think), like my original Wizard's was. I was so happy that I found it, that I forgot about G3 chips existence 8)
Well, ROM was for G3 -_-
Just ran too fast and slipped. Maybe I got that speed after very often Pioneer BCT 1430 flashing. It is just immortal :]
well i know about the G3 and G4 but the rom that i downloaded from doesn't say anything about support G3 or G4 thats why i consider this rom doesn't included IPL and SPL just like the custom rom been make from other member.
Damn now i have to send my phone back to factory for fixing it. Lucky i still have a warranty of it.
nicholas99 said:
well i know about the G3 and G4 but the rom that i downloaded from doesn't say anything about support G3 or G4 thats why i consider this rom doesn't included IPL and SPL just like the custom rom been make from other member.
Damn now i have to send my phone back to factory for fixing it. Lucky i still have a warranty of it.
Click to expand...
Click to collapse
I do feel for you. I believe that the best thing that we can do is to not even make G3 ROM's available to the general public. Maybe all new ROM releases should be IPL/SPL - less. If one needs a ROM that will upgrade their bootloader they'll have to request a password protected file.
I just dunno...
Dr Puttingham said:
I do feel for you. I believe that the best thing that we can do is to not even make G3 ROM's available to the general public. Maybe all new ROM releases should be IPL/SPL - less. If one needs a ROM that will upgrade their bootloader they'll have to request a password protected file.
I just dunno...
Click to expand...
Click to collapse
...which is one of the reasons why carriers make it so hard to flash a ROM from one carrier to the device of another.
Qtek 9100 half bricked
Hi Molski
I'm new here.Just 'd like to know if you could support me on this matter.
Here we go...
I've flashed my 9100 from wwe to esn (spanish) with the ROM 1.3.7.5 or something like this.
This is the problem...I got a power failure in the middle of the flashing process.So now the device isnt able to start up it didnt install the OS properly.
Now it says:
IPL 2.24 (i managed to flash the ipl n spl)
SPL 2.24
OS 1.3.7.5
But I'm pretty sure that there's no OS watsoever because after keep trying flashing with other ROM in bootload mode.I finally managed with an Orange of 34 mb it updated the ROM,that is the IPL And SPL and with the process was running I've noticed the screen got blank and updated it properly.I was realy happy when I saw it but even though it did it properly I still got the same problem.The pda doesnt start up.When I flashed it for the first time I did it with care,followed all the instructions,that is, unlocked the CID first etc.But had the damn joy of getting a power failure in the middle of it.
I'm just wondering if one of you would be able to gimme a light on it.I've tried everything but flashing it with a G4 ROM coz I know it wont work.
Regards
Luiz Santos
Molski[/QUOTE]

[Walkthrough] How to fix your bricked phone

So, you've decided that your shiny new toy isn't very well setup by default. You flashed a ROM and lo and behold, you missed some instruction somewhere and now you think it's bricked.
Here's the good news:
It's not bricked!!
Bricked means that it's dead and it's in no way or shape recoverable.
There is still a chance. (As long as you didn't try to hardSPL with another Device's SPL...)
All you have to do is:
For the WING:
Hold the Camera button and WHILE holding it, soft reset the device (that means press the little hole above the memory card with the stylus.) That will bring you to the bootloader. Now download the appropiate RUU and run that program. A few minutes later and your new shiny toy is back to it's crappy OEM but working self!
I'll put in links for those who can't find them...
Here's tmobile's ROM.
WOW! That´s all??
Ok - then provide us a link to a XDA Terra RUU!!!!!!
hahahaha. Thanks for this help. Maby for some people it is usefull - but written 1000 times before.
ivanmmj said:
So, you've decided that your shiny new toy isn't very well setup by default. You flashed a ROM and lo and behold, you missed some instruction somewhere and now you think it's bricked.
Here's the good news:
It's not bricked!!
Bricked means that it's dead and it's in no way or shape recoverable.
There is still a chance. (As long as you didn't try to hardSPL with another Device's SPL...)
All you have to do is:
For the WING:
Hold the Camera button and WHILE holding it, soft reset the device (that means press the little hole above the memory card with the stylus.) That will bring you to the bootloader. Now download the appropiate RUU and run that program. A few minutes later and your new shiny toy is back to it's crappy OEM but working self!
I'll put in links for those who can't find them...
Click to expand...
Click to collapse
papamopps said:
WOW! That´s all??
Ok - then provide us a link to a XDA Terra RUU!!!!!!
hahahaha. Thanks for this help. Maby for some people it is usefull - but written 1000 times before.
Click to expand...
Click to collapse
I know it has been stated a million times. I'm just tired of the same question being asked over and over again and so here we are...
Too bad it'll be stated a million more times afterwards too.
falconeyez said:
Too bad it'll be stated a million more times afterwards too.
Click to expand...
Click to collapse
If we sticky it and threatened their lives if they don't read it... lol
ivanmmj said:
For the WING:
Hold the Camera button and WHILE holding it, soft reset the device (that means press the little hole above the memory card with the stylus.) That will bring you to the bootloader. Now download the appropiate RUU and run that program. A few minutes later and your new shiny toy is back to it's crappy OEM but working self!
Click to expand...
Click to collapse
It will not help!
ASerg said:
It will not help!
Click to expand...
Click to collapse
And we hold their pet's hostage?
ivanmmj said:
And we hold their pet's hostage?
Click to expand...
Click to collapse
Or better yet, tell them to send us their phones, then we "unbrick" them and sell them on eBay.
falconeyez said:
Or better yet, tell them to send us their phones, then we "unbrick" them and sell them on eBay.
Click to expand...
Click to collapse
Might work out, I get 10% of the over all sold
Ghostrider
Ghostrider said:
Might work out, I get 10% of the over all sold
Ghostrider
Click to expand...
Click to collapse
Fine, but I get 15% because it's my thread.
The instructions to do this are actually in my newbie thread. Which is a sticky.
TylerC161 said:
The instructions to do this are actually in my newbie thread. Which is a sticky.
Click to expand...
Click to collapse
I know, but most people don't search. I figured, maybe if it says "How to fix your bricked phone" on the title, they might get the idea.
It was actually done mostly as a joke...
help
I used the hardSPL from this thread..
http://forum.xda-developers.com/showthread.php?t=358225
It worked successfully and I was able to restart into WM6. Then I tried loading the TouchIT 4.4 and it installed cleanly with no errors. But when I went to restart it, my Wing just sits there at the CanonYang boot screen and never changes.
I tried using the steps here to restore the tmo default rom, but it after 1% on the progress bar, the screen goes blank and the CanonYang screen comes back. Is there anything I can do?
edit: I can get to the bootloader screen with the color bars. I'm not sure if this additional info will be of any help.
IPL 4.10.0002
SPL 4.70.Yang
gumbico said:
I used the hardSPL from this thread..
http://forum.xda-developers.com/showthread.php?t=358225
It worked successfully and I was able to restart into WM6. Then I tried loading the TouchIT 4.4 and it installed cleanly with no errors. But when I went to restart it, my Wing just sits there at the CanonYang boot screen and never changes.
I tried using the steps here to restore the tmo default rom, but it after 1% on the progress bar, the screen goes blank and the CanonYang screen comes back. Is there anything I can do?
edit: I can get to the bootloader screen with the color bars. I'm not sure if this additional info will be of any help.
IPL 4.10.0002
SPL 4.70.Yang
Click to expand...
Click to collapse
SPL 4.70.yang!!! your device is HARD-SPL!!
So going back to stockrom--> delete the SPL.nbh from EVERY RUU you are running.
Then it shouldn´t stop......
Big Thanks papa! That did the trick. My Wing is happy once again and running Open Touch. But I still want to give TouchIt another try.
And what if i cant find stock RUU mine came with some arabic keyboard and spl was 1.08 , thanks to Oli he didnt mention that SPL should be 4 or higher , so device is bricked since first Olis release and no way to find this arabic stock RUU.
Any Help ?????
Hitec
If the device had an spl of 1.08 prior to HardSPLing it, then you'll have to bring the device to your nearest repair center. There isn't a way around that. Oli doesn't know everything and that's the risk we take when we try new and experimental things that people create but have no way of testing. But, we live and learn. If it wasn't for that issue, you could always cook your own ROM and if the HardSPL was working, you could've easily flashed any ROM. But the keyboard wouldn't been wrong until you could find someone who had the correct keyboard and you extracted the ROM from it and cooked that keyboard driver into your ROM.
Oh noooo!!
Hi ivanmmj,
I used your guide to flashing my HTC P4350 at http://forum.xda-developers.com/showthread.php?t=358615.
It was in French and I wanted it in English. So I downloaded one of the official HTC ROMs "HTC_P4350_WWE_4.17.405.2_4.1.13.44_02.94.90_Ship.exe" assuming this was the English one because all the others couldn't have been.
I copied the "RUU_signed.nbh" from the above HTC ROM and put it into the RUU folder as instructed by yourguide (I didn't copy the SPL.nbh file). I then ran the herald-uspl.exe and everything went fine until the RUU utility stopped with the error "invalid vender ID".
The RUU exited without completing, now all I get when the device boots is the screen giving my IPL (1.08.001) and SPL (1.08.001). How do I flash another ROM from this state? I can't do it the "normal" way because ActiveSync can't see the device. When I try to use the RUU tool that comes with your tool, the progress bar shows then it says the tool can't be used with my device.
Someone please help!
foo_bar_baz said:
Hi ivanmmj,
I used your guide to flashing my HTC P4350 at http://forum.xda-developers.com/showthread.php?t=358615.
It was in French and I wanted it in English. So I downloaded one of the official HTC ROMs "HTC_P4350_WWE_4.17.405.2_4.1.13.44_02.94.90_Ship.exe" assuming this was the English one because all the others couldn't have been.
I copied the "RUU_signed.nbh" from the above HTC ROM and put it into the RUU folder as instructed by yourguide (I didn't copy the SPL.nbh file). I then ran the herald-uspl.exe and everything went fine until the RUU utility stopped with the error "invalid vender ID".
The RUU exited without completing, now all I get when the device boots is the screen giving my IPL (1.08.001) and SPL (1.08.001). How do I flash another ROM from this state? I can't do it the "normal" way because ActiveSync can't see the device. When I try to use the RUU tool that comes with your tool, the progress bar shows then it says the tool can't be used with my device.
Someone please help!
Click to expand...
Click to collapse
Oh wow. I'm so sorry. I think I may have forgotten to put up a warning for people that have an SPL lower than 4.0. Was your SPL lower than 4.0? If it was, you cannot use the USPL OR the HardSPL and they end up writing part of the ROM over your current SPL and brick the device. This, unfortunately, needs to be fixed by your local repair center. I'll talk to the Mods about unlocking that thread so that I can update it.
ivanmmj said:
Oh wow. I'm so sorry. I think I may have forgotten to put up a warning for people that have an SPL lower than 4.0. Was your SPL lower than 4.0? If it was, you cannot use the USPL OR the HardSPL and they end up writing part of the ROM over your current SPL and brick the device. This, unfortunately, needs to be fixed by your local repair center. I'll talk to the Mods about unlocking that thread so that I can update it.
Click to expand...
Click to collapse
Oh deary me! I am so dead now - I live in Tanzania, East-Africa. My "local" repair center is several hundred thousand miles away across The Big Blue. What exactly do the repair center folks do to fix the device? Perhaps I can soldier out myself with some guidance...
Thank you,
foo_bar_baz.

restoring a bricked phone

any ideas.......read all the threads here, nothing works.
i had the 1.7 orange version. hardspl'd it and put a 6.5 dev on there, but radio quality was poor. so followed the procedure to put the stockspl back on there. But nothing else works, I can't restore the original rom (grabbed from here) as the screen stays at 0%. tried to hardspl it again but that doesn't work either.
what do i do now .........?
thanks.
Was restoring the stockspl succesfull?
What info do you get in bootloader?
The info is:
JADE110 64M
SPL-1.40.0000
MicroP-Jade (LED) v5
It still has windows 6.5 rom on there tho, which is seriously messed up now.
pls dont wast threads
hi
a humble request Kindly dont was threads i have created a specific thread for Q& A on Jade why not post it their pls see below link
i see u have wasted 3 thread which could have been used for a much more usefull purpose this is just my humble request to you i hope u will do the neeful thanks
Note : kindly read the first page u would understand why not to waste threads
http://forum.xda-developers.com/showthread.php?t=534581
orange3g said:
any ideas.......read all the threads here, nothing works.
i had the 1.7 orange version. hardspl'd it and put a 6.5 dev on there, but radio quality was poor. so followed the procedure to put the stockspl back on there. But nothing else works, I can't restore the original rom (grabbed from here) as the screen stays at 0%. tried to hardspl it again but that doesn't work either.
what do i do now .........?
thanks.
Click to expand...
Click to collapse
"a humble request Kindly dont was threads" read your thread on that, space taken up whether new thread or reply is the same.
orange3g said:
The info is:
JADE110 64M
SPL-1.40.0000
MicroP-Jade (LED) v5
It still has windows 6.5 rom on there tho, which is seriously messed up now.
Click to expand...
Click to collapse
Am afraid you have a problem, you should have down it the other way around...first stock ROM then stock SPL.....but this is merely a fact then helping you out, i have absolutely no clue how to go from here...sorry!
Maybe someone who can offer some practical assistance will be along soon ......
@Nirak: yes, I misread it. What a silly thing to do. Do you think HTC can help. The phone is in warranty.
Well, since you've got stock SPL on it you could give it a try. When they start asking questions you could say you tried to install a WM 6.5 ROM by accident.., dunno if they buy it...
But on the other hand, being honest is maybe better, they might just help you out or else you have to pay, but since you have a rather expensive paperweight right now, this might be an option too.
BTW.. did you try to contact one of the releasers of the HardSPL? (Cmonex or Olipro), you never know where they can come up with....
May be they will see this thread. .... otherwise how can I contact them?
Thanks for the ideas.
Have you tried to flash your rom through the boot loader mode
try this
hi
try this
1. do HSPL on ur phone again using the tools given in the thread
2.after successful HSPL Flash the Stoc rom the right one for ur phone
3.then flash the Stock SPL again the right spl for ur phone
this is just my suggestion i hope ur successful and it helps to solve ur problem
goodluck
orange3g said:
May be they will see this thread. .... otherwise how can I contact them?
Thanks for the ideas.
Click to expand...
Click to collapse
Send them a PM, Olipro is not often here, but Cmonex is
haree said:
hi
try this
1. do HSPL on ur phone again using the tools given in the thread
2.after successful HSPL Flash the Stoc rom the right one for ur phone
3.then flash the Stock SPL again the right spl for ur phone
this is just my suggestion i hope ur successful and it helps to solve ur problem
goodluck
Click to expand...
Click to collapse
Doesn't work because it needs a functioning windows mobile, which I don't have. Mine gets stuck.
thomas01_58 said:
Have you tried to flash your rom through the boot loader mode
Click to expand...
Click to collapse
Yes, nothing happens. The screen is stuck at 0%. I tried using a htc original rom, it got to 1% and said something like not suitable for this device.
I sure this sounds rather silly ,and I am sure you have tried it,have you tried removing the battery and then putting it back again.
Not sure if you tried this already:
Run HardSPL when your phone is in tricolor mode (bootloader?).
Then reflash a stock ROM, also in tricolor mode.
Finally, flash stock SPL.
Hope this helps.
@izzysc: I have tried it (will try again though) in running HardSPL when phone is in tricolor mode. It did not work.
Nirak said:
Well, since you've got stock SPL on it you could give it a try. When they start asking questions you could say you tried to install a WM 6.5 ROM by accident.., dunno if they buy it...
But on the other hand, being honest is maybe better, they might just help you out or else you have to pay, but since you have a rather expensive paperweight right now, this might be an option too.
BTW.. did you try to contact one of the releasers of the HardSPL? (Cmonex or Olipro), you never know where they can come up with....
Click to expand...
Click to collapse
I have PMd Cmonex. Thanks.
replied to PM
cmonex said:
replied to PM
Click to expand...
Click to collapse
Tx! had an idea you could help out...

My Touch HD just died

Hi,
I just flashed Pdavietv 65.
After 10 minutes of using it, I locked the phone using the WM lock.
When i wanted to unlock it, the screen doesn't respond anymore.
I did a hard reset, I can't type anything on the screen, screen doesn't feel my fingers....
Anyone has an Idea?
I try to flash stock rom right now...
Sorry for my bad english
darkblue68 said:
Hi,
I just flashed Pdavietv 65.
After 10 minutes of using it, I locked the phone using the WM lock.
When i wanted to unlock it, the screen doesn't respond anymore.
I did a hard reset, I can't type anything on the screen, screen doesn't feel my fingers....
Anyone has an Idea?
I try to flash stock rom right now...
Sorry for my bad english
Click to expand...
Click to collapse
Flash another rom from the tri-color screen.
I just flashed the frenck Stock Rom From HTC.
I can't access.
When i 've the screen 'tap the screen to align screen', Nothing happens when i Touch the screen.
Only vol UP and down and power off are working....
Any solution?
Thanks
I think your digitizer unit died..get one one ebay and replace it
try fresh a stock rom which includes SPL as well.
mcdull said:
try fresh a stock rom which includes SPL as well.
Click to expand...
Click to collapse
You have a link please?
darkblue68 said:
You have a link please?
Click to expand...
Click to collapse
Try Putting your Phone in BootLoader mode.
Flash it with HARD SPL1.56
Then Try Installin a Fresh firmware again, a Hard Reset n it will be fixed.
I did all of this...
Nothing, I think I must send it to HTC...
I think your HD died touchscreen . You need to bring the HTC Service Center for repairs. If you is bought on ebay then there will pay for about 200 USD
My Touch HD just died
R.I.P. !
Damn all was working nice.
I did nothing.... Only flashed all days another rom
And when i wanted to call a friend yesterday,the screen didn(t respond anymore....
Grrr, I will send it to HTC this week, and i will by a Topaz One...
Leo is too big for my pocket....
ancola66 said:
I think your HD died touchscreen . You need to bring the HTC Service Center for repairs. If you is bought on ebay then there will pay for about 200 USD
Click to expand...
Click to collapse
DIY for 30 USD..ebay the spare part.
Had one same condition and fixed flashing with an original rom. Radio+Rom and Align screen on startup/\
I was in same condition as yours ,When in typped align scren nothing but after flash and a hard reset everything getback
Me, nothing after flshing original Stock ROM and originalHSPL.
But solething is very strange.
When the backlight power off (the dimmer), it comes back when i hit the screen... But i can't align the screen, the screen doesn't recognise my touch.
Why the dim is working when i hit the screen ans my gesture are not recognised?
Thanks a lot
Greats from France
It looks like only the alignment of the screen is wrong. Why it does not get fixed when flashing original ROM is strange. But the fact that the screen response to touch (returning from dim) should mean that the digitizer is OK.
Yes I think the digitizer is OK.
But I don't know what the problem is.
I will try to reflash tomorrow a custom Rom without align to screen at first boot....
Thanks
try mtty to completely erase ur internal memory..
then flash stock rom..
Ok, a few simple queries to help solve your issue. I'm assuming you used USPL or HSPL before flashing rom? and correct version of HSPL? Can you still access bootloader? What is your SPL?
If you can access bootloader, all is not lost and your device is not bricked.
I'd recommend flashing original stock rom onto your device and starting from fresh. Stock roms can be found in the wiki here. Once you have restored stock rom and if you still want a cooked rom, follow thisguide.
Let me know the answer to the above queries and how you get on.
Hi,
I used the SPL by Olinex.
Now i revert back to the original SPL.
When i enter in booloader mode, I can see: SPL-1.54.0000
Is this ok?
Before flashing the origal SPL i flashed the original French Stock ROM.
What is MMTY ?
Thanks
darkblue68 said:
Hi,
I used the SPL by Olinex.
Now i revert back to the original SPL.
When i enter in booloader mode, I can see: SPL-1.54.0000
Is this ok?
Before flashing the origal SPL i flashed the original French Stock ROM.
What is MMTY ?
Thanks
Click to expand...
Click to collapse
Solution should be found here including MTTY info & instructions. Same method for HD

Please help, I think I bricked my phone :(

Sorry if I shouldn't be writing a new thread about this, but I couldn't find a thread about bad flashes...
I'm a newbie with this, and I think I just bricked my phone after only my second flash I have a Touch Pro 2 (T-Mobile), and I was able to successfully install HardSPL. I even flashed the EnergyROM LEO with no problems. After a few days of playing around, I tried to flash the AthineOS v2.0 ROM, and now my phone won't boot up... it gets stuck in the Touch Pro 2 black screen with the red lettered version numbers at the bottom. I tried rebooting and pulling the battery out, but I have had no success in being able to boot it back up.
Any ideas on how I can fix this? This sucks I've only had the thing for less than a month...
localcall001 said:
Sorry if I shouldn't be writing a new thread about this, but I couldn't find a thread about bad flashes...
I'm a newbie with this, and I think I just bricked my phone after only my second flash I have a Touch Pro 2 (T-Mobile), and I was able to successfully install HardSPL. I even flashed the EnergyROM LEO with no problems. After a few days of playing around, I tried to flash the AthineOS v2.0 ROM, and now my phone won't boot up... it gets stuck in the Touch Pro 2 black screen with the red lettered version numbers at the bottom. I tried rebooting and pulling the battery out, but I have had no success in being able to boot it back up.
Any ideas on how I can fix this? This sucks I've only had the thing for less than a month...
Click to expand...
Click to collapse
hi if you have done the hardspl then try this
to enter Bootloader
Remove the back cover from the phone.
Hold the Volume Down button.
Use the stylus to press the reset hole.
Or if the device was powered off, press the power button whilst holding down the Volume Down button.
you should see serial at the bottom of the three color screen then plug in the usb cable the serial should change to USB then just flash another rom.
i hope this helps you.
Thank you! Thank you! Thank you! Thank you! That worked! That's a really cool recovery feature from HardSPL... you guys really know what you're doing This is such a huge relief...
localcall001 said:
Thank you! Thank you! Thank you! Thank you! That worked! That's a really cool recovery feature from HardSPL... you guys really know what you're doing This is such a huge relief...
Click to expand...
Click to collapse
only to pleased to help I am glad you got your phone back working
localcall001 said:
Thank you! Thank you! Thank you! Thank you! That worked! That's a really cool recovery feature from HardSPL... you guys really know what you're doing This is such a huge relief...
Click to expand...
Click to collapse
hehehe finally you found solution.. but my rom does not have any problem.. somethings goes wrong
b16b said:
hehehe finally you found solution.. but my rom does not have any problem.. somethings goes wrong
Click to expand...
Click to collapse
idd, this is not ROM related, its just unlucky like hell. See the phone as a PC, where blocks need be written. If a block fails or is corrupt, you get these jokes. Its like a BSOD on a Windows PC.
I gotta admit it is great knowing that once you've done a hardspl you are safe as houses as even if you flashed the most currupted ROM, the bootloader will always allow a reflash.
This is way more stable and safe than any other experience I've had of phone flashing.
b16b said:
hehehe finally you found solution.. but my rom does not have any problem.. somethings goes wrong
Click to expand...
Click to collapse
Funny that, your latest ROM was the only one I had problems with - the same problems as the original poster, in fact. I flashed a different ROM fine, re-downloaded your 2.0 and flashed it again, same problem. Hanging on the boot screen.
b16b said:
hehehe finally you found solution.. but my rom does not have any problem.. somethings goes wrong
Click to expand...
Click to collapse
Probably I think I was just unlucky. My fear (while I was panicking) was that your ROM is European based, and since mine came from T-Mobile, it didn't mesh well. I also didn't unlock my phone so that could be also be a problem...
awesome community
localcall001 said:
That's a really cool recovery feature from HardSPL...
Click to expand...
Click to collapse
well..this is a normal recovery feature for stock spl also
Same Issue
I had the same issue with AthineOS v2.0 ROM it gets stuck on Touch Pro 2 logo
wahida76 said:
I had the same issue with AthineOS v2.0 ROM it gets stuck on Touch Pro 2 logo
Click to expand...
Click to collapse
no one have told me that on my thread... only here i found this issue.. and finally how pass the problem?
I had to re-flash a different ROM.
I'm wondering if it's related to the radio version...
what is your version of radio
can't you flash the latest 23060?
i use radio 3.36
I've used 4.49.25.05 and have just got the same result on 4.49.25.17
I'll try flashing 3.44.25.27 (the oldest in the radio thread) and re-flashing your ROM.
Alas, no luck with that one either.
I have no idea why it doesn't seem to work on my Rhodium :/
I'm sorry if I'm hijacking this thread but it's the only one I've found that's even close to having the same issue I have, though I'm still using the stock rom/os.
I was installing winmo msn messenger. It installed fine and reset my tp2 fine. It goes thru the tp2 splash screen, the verizon splash screen and the winmo splash screen. Then it shows owner information and this is where it gets screwed up. Owner info will stay up forever if I dont touch the screen. After touching the screen the only thing left will be the top bar and the rest of the screen stays black. The only things on the top bar are the signal icon (which always has an x), the wifi icon (which seems to be connected fine lol) and either owner info will still be in the upper left or the start menu will be there. Hitting the screen only causes my tp2 to beep.
Nothing I know how to do (which is basically just hard and soft resetting it) works. Verizon can't fix it (didnt think they would be able to) and I can find no drivers (possibly cause I'm still a noob with winmo) to resolve my issue. I'm not even sure how I'd get them on as it wont even sync up to my computer and my computer cannot find its hd. If I could get a rom for the verizon one I think I can figure it out from there with no issues...but htc website sends me to verizon website for support and vice versa. The htc wiki is the closest I've gotten to an answer...but no rom to download. The only OEM roms I can find anywhere aren't for this phone, unless one of those will work? You guys are the experts.
Does anyone know what I can try? Verizon wants me to return it but cannot tell me when I'll get my new one as they are out of stock...again. Please help lol! Thanks for any and all help.
Mr.Clark said:
I've used 4.49.25.05 and have just got the same result on 4.49.25.17
I'll try flashing 3.44.25.27 (the oldest in the radio thread) and re-flashing your ROM.
Click to expand...
Click to collapse
i using this..
*Change the radio to 3.46.25.30 (Hot Fix For GPS Lock)
and also try the latest release of my rom.. (maybe you have bad file bad download)
b16b said:
i using this..
*Change the radio to 3.46.25.30 (Hot Fix For GPS Lock)
and also try the latest release of my rom.. (maybe you have bad file bad download)
Click to expand...
Click to collapse
Sorry, I tried that one as well yesterday. And I've downloaded your ROM a few times too...
Are you still working on the 6.1 ROM? Maybe a new version will just magically start working for me...
EDIT: Tried a fresh 3.46.25.30 and a fresh download of your ROM. Still nothing

Categories

Resources