Need help...please... - P3600 Software Upgrading

Hi..
I've bought a SIM blocked Trinity.
I've tried to use POF's unlocker, but I cannot get the thing to pass through the bootloader stage.
Everytime I get the device into bootloader, I try to install the newer radio rom, unchecking first the USB conections in Active Sync, but I always receive the message to check if the device is conected into the USB cable!!!
I use XP by the way...
Can anyone tell me a way to get through this stage???

What is your SPL version? Press on/off button + camera to enter in the tricolor screen.

HTC Trinity original ROM
Here is the original HTC Trinity ROM:
http://rapidshare.com/files/20284524...12201_Ship.zip
1. Press on/off button + camera button + reset (using the stylus)
2. You should now be in tricolor screen.
3. Connect the usb cable.
4. Make sure you have activesync runing.
5. Install the rom provided in the link.
In the link you will find rom+radio. (Radio version 1.20)
Here is a newer radio version 1.56:
http://rapidshare.com/files/203126613/1.56.70.11.exe

Related

Big Problem with Diamond

Hi,
i've a big problem with my diamond
it starts normally, but after htc splash screen, it tries to load windows but after 1-2 seconds it restart.
i was using cooked rom gen.Y D2 rev.Y with radio 1.09.25.23
G 52.51.25.26H
i've tried with original rom 2.03 but the problem still remains.
What can i do to resolve this problem?
Where can i find original radio and G (what does it stand for?) to put inside my htc with original rom for probably warranty assistence (i hope)
i've also olinex1.40 spl, how can i remove it?
Thank you in advance
Gianluca
SOunds like a bad flash to me. Try using MTTY to reflash. Should work fine
http://forum.xda-developers.com/showthread.php?t=540290
how can i run this procedure:
Connect Device to PC via Active Sync, Once Connected Uncheck USB Connections,DISCONNECT DEVICE then Reboot Computer
if the device can't start completely?
Flash from your System not the Internal Storage. Read the 4th post.
i can't install drivers on my win7 x64 because i can't follow the first post "how to install drivers" so with the mtty.exe it doesn't find the usb driver
In that case see if you can get into bootloader.
(Reset + Hold Vol Down), this will show the Red, Blue, Green screen showing "Serial"
Then plug your usb cable in and you should get it showing "USB".
You then need to Hard SPL and reflash.
yes i've succesfully installed drive on win7 x64
i've run mtty.exe, followed the instructions, all ok.
then i've disconnected the diamond from usb and made an hard reset (it says press vol.up to restore manufacturer default, vol. down to restore and format movinanand, i press vol. up, and after vol.up again: is it the hard reset or is it another menu?)
but after restart the htc has same problem..it continues to restart by itself
i've decided to return htc to stock software and firmware in order to send him in warranty to delaer.
so, i've installed last official rom htc 2.03, it includes the radio.
Now after that, because system doesn't want to start completely, also after mtty.exe format ecc., the last thing i've to do is install official spl right?
i've found the guide:
STEP BY STEP HOW TO RETURN TO STOCK SPL - FOR WARRANTY REASONS ONLY!
0. be sure to first restore stock OS, and stock radio. stock SPL is always to be done last!!
1. download the stock spl package from this post (pick one of the attachments) in this thread.
2. also download the RUU-SSPL-withoutNBH.zip from the attachments in this post.
3. pick the SPL you want to reflash to (ONLY FOR WARRANTY REASONS), it's a .NBH file, put the NBH in the extracted RUU-SSPL-withoutNBH package.
4. run the RUU (or if needed, run SSPL-Manual.exe manually, then run RUU when it goes to black screen), it goes to 100%, reboots, done.
+5. to verify, volume down + reset, see version number on tricolour screen.
that's it.
what official spl have i to install? 1.23 1.34 1.37?
i've tried with all the 3 spl but nothing changed i think, because when i open the bootloader it still saying 1.40olinex

Need Help Please With My HTC P3600 Hardspl error (260)

Hi, i would like to somebody helps me, i got my htc recently and i can't do it a hardspl i do all the steps and when it comes to almost finish gave an error i've tried with many different hardspl and nothing, i will show you the erros that gaves me... please help me with this problem, cause i can't do anything to my htc...
Hi
I have the some problem, I have follow this guide :
Step 2 - Upgrade to Hard SPL
Hard SPL will allow you to flash cooked ROMs without SuperCID’ing your device and also will protect your device from being bricked in a bad flash. If a bad flash occurs it should remain in bootloader, and you can re-flash another ROM.
Before you proceed, check which SPL is on your device. Manually enter the Bootloader by pressing the Power button, Camera button and performing a soft reset at the same time. If your SPL is 3.20.Olipro then you already have Hard-SPL on your device and can skip this step and proceed to upgrade your ROM or radio.
1. Download the Hard-SPL for P3600i (do NOT use any of the Hard-SPL's for Trinity/DoPod)
* Hard SPL 3.20.Olipro (P3600i HardSPL v1.1)
2. Unzip the Files, and click on ‘ROMUpdateUtility.exe’
Image Missing
3. Check the checkbox, and click ‘next’
Image Missing
4. Follow the directions in the window, and establish an activesync connection with your device
* Make sure the activesync icon is be green (finished synchronizing)
* Make sure your battery is charged
Image Missing
5. Check the checkbox, click ‘next’
Image Missing
6. In the next window, click the ‘Update’ button
This will show the version number of the ROM, radio, or in this case bootloader that you are about to flash.
Image Missing
7. After the version number has appeared, click next
Image Missing
8. In the following window, click ‘next’
after you click this, the flash will begin, so do not disconnect your device or do anything stupid on your computer
Image Missing
!NOTE! (quoted straight from Jon's post on first page)
WHEN FLASHING HARDSPL, IT WON'T WORK THE FIRST TIME - YOU WILL GET AN ERROR (CODE 260). THIS IS EXPECTED.
Quote:
Originally Posted by joncgde2
This is what happens.
You go to flash HardSPL like the guide says. LOOK AT THE SCREEN ON YOUR PHONE, YOU MIGHT HAVE SECURITY PERMISSIONS AND NEED TO MANUALLY ALLOW THE PROGRAMS TO RUN.
It looks like it's about to flash and then errors. BUT your phone is on the 3-colour bootloader screen! How odd. Well KEEP YOUR PHONE ON THE BOOTLOADER SCREEN, and unplug it from your computer. Exit the HardSPL program, RUN IT AGAIN, and FLASH THE PHONE AGAIN WITH HARDSPL (obviously connect your phone and stuff back to your PC).
The point here is this: the first time it will fail, but at least manage to get the bootloader up. With this bootloader up, exit the flashing program, restart it, and then you should be able to run the flashing program and have it complete.
DOUBLE CHECK YOUR PHONE HAS THE OLIPRO HARDSPL INSTALLED after completion, by soft-resetting (hold the power and camera buttons at the same time AND use the stylus to press the putton at the bottom of the phone. You might not get it the first time, but with practice you'll get the hang of it).
9. A Progress bar will appear on your computer screen, and your trinity will display a grey screen with progress bar. Be patient while your device is being updated.
Image Missing
Image Missing
10. Once your device is finished updating, it will automatically soft reset. Click the ‘Finish’ button to exit the RUU program.
Image Missing
To confirm is Hard-SPL is on your device, manually enter Bootloader by pressing the Power button, Camera button and performing a soft reset at the same time. If successful you will see the tri-colour screen and the following will be displayed
Hard SPL 3.20.Olipro (P3600i HardSPL v1.1)
but also after restart a lot of time HARDSPLromupdateutility.exe, I still have the same problem!
anybody may help me?
Now I have stratos image,
maybe is this the problem?
Hi
Pls I need help, I tried to upgrade my HTC P3600 then my computer crash so now every time I try to start my phone all what I got is a picture (HTC start mobility) and then nothing.
Pls help me.
Thanks
Hi gys, I think that this is my first post, but I want to share some solution for with you. The most important think with "connection" errors is to have HSPL installed correctly. I was trying to install on my HD2 universal ones, like Hard spl v7 and 9, but problems occured. So after trying everything, I found HSPL (on this forum) just for HD2. After that, everything wass like a charm
Hi,
my P3600 has a serious problem! I've flashed an Elegant Ed. (but I don't remeber the version). Now, I'd like to reinstall original ROM, but this is the results:
1) PC WIN VISTA: Activesync get ON, the PC see the PPC and the result is CONNECTED.
2) Incoming to update the PPC but the error IS 260 (communication error)
3) in the bootloader is indicated:
a) TRIN100 - IPL-0.50
b) TRIN100 - SPL-1.07.0000
c) serial
4) I downloaded [P3600i] HardSPL v1.1 and installs its on PPC and in bootloader there's (but error 260 continues to work )
a) TRIN100 - IPL-0.50
b) TRIN100 - SPL-3.10.Olimpo
c) PPC in bootloader config.
d) serial
5) Now, there's a SPL on my PCC !!! Connect and disconnect my USB cable by PPC, leaving PPC in bootloader configuration and by activesync disable "connect by USB"
6) insert usb cable in PPC, but it doesn't go to USB
..... I do not know what to do !!!!
Please help my
Junior
base167 said:
Hi,
my P3600 has a serious problem! I've flashed an Elegant Ed. (but I don't remeber the version). Now, I'd like to reinstall original ROM, but this is the results:
1) PC WIN VISTA: Activesync get ON, the PC see the PPC and the result is CONNECTED.
2) Incoming to update the PPC but the error IS 260 (communication error)
3) in the bootloader is indicated:
a) TRIN100 - IPL-0.50
b) TRIN100 - SPL-1.07.0000
c) serial
4) I downloaded [P3600i] HardSPL v1.1 and installs its on PPC and in bootloader there's (but error 260 continues to work )
a) TRIN100 - IPL-0.50
b) TRIN100 - SPL-3.10.Olimpo
c) PPC in bootloader config.
d) serial
5) Now, there's a SPL on my PCC !!! Connect and disconnect my USB cable by PPC, leaving PPC in bootloader configuration and by activesync disable "connect by USB"
6) insert usb cable in PPC, but it doesn't go to USB
..... I do not know what to do !!!!
Please help my
Junior
Click to expand...
Click to collapse
You have choice a wrong HardSPL !!!
Olipro 3.10 and 3.20 are for HTC P3600i and no working for TRINITY P3600.
So, now probabily you don't see "USB" on Bootloader when you connect you trinity on PPC.
Solution:
You must reload your H-SPL With SD CArd.
It's very simple:
searching for a Hard SPL for trinity device, example Olipro 1.20 and rename file "RUU_signed.nbh" ---> "TRINIMG.nbh".
Then copy file "TRINIMG.nbh" in a SD CARD and insert it on your Trinity; After that , make a Soft reset with stylus reset +power+camera.
Power bottom for update your Bootloader.
Now you would see your trinity working again
Davide

Problem in Starting Screen in HTC Tytn II !

I was make restart for my PDA HTC Tytn II and it didnt open only i see The Starting Screen Windows Mobile version 6.1 and i was tray to upgrad the ROM the PC cant see the HTC ?
any one can help my ???
Have you flashed any HardSPL?
If the PC doesn't see the phone, maybe you have to enter the bootloader first before could upgade your ROM.
1. Hold power + camera + reset button to enter the boot loader.
2. You will see a tri color screen with "Serial" text at below and then connect your USB cable until the text changed into "USB"
3. Flash your preferred ROM by executing Custom RUU.exe on your PC.
Thanx
Thanks man.
With this solution i dont have to buy another, thanks to you.

My Head hurts....

I am trying to install 6.5 on my HTC touch HD.
i have looked at the guides, but i am getting nowhere......stuck at 0% on the flashing.
I want to flash Energys rom onto my phone.
Phone is currently
SPL 1.14.000
Radio 1.09.25.14
Rom 1.19.61.1 WWE
what do i need and how do i do it ?
i have downloaded
HSPLWrapper_Blackstone_156OliNex,
SSPL-Manual-TouchHD,
Unsigned_HardSPL_for_Blackstone_OliNex,
Energy.BLACKSTONE.29018.Sense2.5.Cookie.2.0.Apr.18
i have tried on both WinXP and Win 7 Systems, same error 262
1- have you tried installing the htc usb sync drivers manually? -->google
2- do you ever see the tri-color bootloader screen? If not you could try to put it in bootloader manually? you can do that by holding vol down+power button. You do have to turn it of first, and you have to remove the usb cable. WARNING: do not pull out the usb cable while its flashing, you won't be able to start your phone then (you can still flash roms though)
hope this helps
when connecting device to pc does bottom of bootloader (tri colour screen) change from "serial" to usb"? If not you need to either update drivers (see link in Dummies Guide) or open activesync and ensure that "allow usb connections" is enabled in connection settings
If above is all ok then you need to follow guide and get yourself HSPL
If getting stuck at 0% try trouble shooting section and use SSPL
Either way, please post further queries regarding flashing in Dummies Guide thread
Thread closed

Dopod D810 / Trinity p3600 stuck at wm6 boot screen

I I can clearly see that this is a known issue, I have tried to flash it via the bootloader (from holding power, camera and reset button) but every guide i have followed says that i need to connect it via activesync to do that, and i cant because windows doesnt detect it as a phone it just detects it as a "HTC usb sync".
I really am stumped on what to do.

Categories

Resources