Problem in Starting Screen in HTC Tytn II ! - Tilt, TyTN II, MDA Vario III General

I was make restart for my PDA HTC Tytn II and it didnt open only i see The Starting Screen Windows Mobile version 6.1 and i was tray to upgrad the ROM the PC cant see the HTC ?
any one can help my ???

Have you flashed any HardSPL?
If the PC doesn't see the phone, maybe you have to enter the bootloader first before could upgade your ROM.
1. Hold power + camera + reset button to enter the boot loader.
2. You will see a tri color screen with "Serial" text at below and then connect your USB cable until the text changed into "USB"
3. Flash your preferred ROM by executing Custom RUU.exe on your PC.

Thanx
Thanks man.
With this solution i dont have to buy another, thanks to you.

Related

Need help...please...

Hi..
I've bought a SIM blocked Trinity.
I've tried to use POF's unlocker, but I cannot get the thing to pass through the bootloader stage.
Everytime I get the device into bootloader, I try to install the newer radio rom, unchecking first the USB conections in Active Sync, but I always receive the message to check if the device is conected into the USB cable!!!
I use XP by the way...
Can anyone tell me a way to get through this stage???
What is your SPL version? Press on/off button + camera to enter in the tricolor screen.
HTC Trinity original ROM
Here is the original HTC Trinity ROM:
http://rapidshare.com/files/20284524...12201_Ship.zip
1. Press on/off button + camera button + reset (using the stylus)
2. You should now be in tricolor screen.
3. Connect the usb cable.
4. Make sure you have activesync runing.
5. Install the rom provided in the link.
In the link you will find rom+radio. (Radio version 1.20)
Here is a newer radio version 1.56:
http://rapidshare.com/files/203126613/1.56.70.11.exe

Need Help Please With My HTC P3600 Hardspl error (260)

Hi, i would like to somebody helps me, i got my htc recently and i can't do it a hardspl i do all the steps and when it comes to almost finish gave an error i've tried with many different hardspl and nothing, i will show you the erros that gaves me... please help me with this problem, cause i can't do anything to my htc...
Hi
I have the some problem, I have follow this guide :
Step 2 - Upgrade to Hard SPL
Hard SPL will allow you to flash cooked ROMs without SuperCID’ing your device and also will protect your device from being bricked in a bad flash. If a bad flash occurs it should remain in bootloader, and you can re-flash another ROM.
Before you proceed, check which SPL is on your device. Manually enter the Bootloader by pressing the Power button, Camera button and performing a soft reset at the same time. If your SPL is 3.20.Olipro then you already have Hard-SPL on your device and can skip this step and proceed to upgrade your ROM or radio.
1. Download the Hard-SPL for P3600i (do NOT use any of the Hard-SPL's for Trinity/DoPod)
* Hard SPL 3.20.Olipro (P3600i HardSPL v1.1)
2. Unzip the Files, and click on ‘ROMUpdateUtility.exe’
Image Missing
3. Check the checkbox, and click ‘next’
Image Missing
4. Follow the directions in the window, and establish an activesync connection with your device
* Make sure the activesync icon is be green (finished synchronizing)
* Make sure your battery is charged
Image Missing
5. Check the checkbox, click ‘next’
Image Missing
6. In the next window, click the ‘Update’ button
This will show the version number of the ROM, radio, or in this case bootloader that you are about to flash.
Image Missing
7. After the version number has appeared, click next
Image Missing
8. In the following window, click ‘next’
after you click this, the flash will begin, so do not disconnect your device or do anything stupid on your computer
Image Missing
!NOTE! (quoted straight from Jon's post on first page)
WHEN FLASHING HARDSPL, IT WON'T WORK THE FIRST TIME - YOU WILL GET AN ERROR (CODE 260). THIS IS EXPECTED.
Quote:
Originally Posted by joncgde2
This is what happens.
You go to flash HardSPL like the guide says. LOOK AT THE SCREEN ON YOUR PHONE, YOU MIGHT HAVE SECURITY PERMISSIONS AND NEED TO MANUALLY ALLOW THE PROGRAMS TO RUN.
It looks like it's about to flash and then errors. BUT your phone is on the 3-colour bootloader screen! How odd. Well KEEP YOUR PHONE ON THE BOOTLOADER SCREEN, and unplug it from your computer. Exit the HardSPL program, RUN IT AGAIN, and FLASH THE PHONE AGAIN WITH HARDSPL (obviously connect your phone and stuff back to your PC).
The point here is this: the first time it will fail, but at least manage to get the bootloader up. With this bootloader up, exit the flashing program, restart it, and then you should be able to run the flashing program and have it complete.
DOUBLE CHECK YOUR PHONE HAS THE OLIPRO HARDSPL INSTALLED after completion, by soft-resetting (hold the power and camera buttons at the same time AND use the stylus to press the putton at the bottom of the phone. You might not get it the first time, but with practice you'll get the hang of it).
9. A Progress bar will appear on your computer screen, and your trinity will display a grey screen with progress bar. Be patient while your device is being updated.
Image Missing
Image Missing
10. Once your device is finished updating, it will automatically soft reset. Click the ‘Finish’ button to exit the RUU program.
Image Missing
To confirm is Hard-SPL is on your device, manually enter Bootloader by pressing the Power button, Camera button and performing a soft reset at the same time. If successful you will see the tri-colour screen and the following will be displayed
Hard SPL 3.20.Olipro (P3600i HardSPL v1.1)
but also after restart a lot of time HARDSPLromupdateutility.exe, I still have the same problem!
anybody may help me?
Now I have stratos image,
maybe is this the problem?
Hi
Pls I need help, I tried to upgrade my HTC P3600 then my computer crash so now every time I try to start my phone all what I got is a picture (HTC start mobility) and then nothing.
Pls help me.
Thanks
Hi gys, I think that this is my first post, but I want to share some solution for with you. The most important think with "connection" errors is to have HSPL installed correctly. I was trying to install on my HD2 universal ones, like Hard spl v7 and 9, but problems occured. So after trying everything, I found HSPL (on this forum) just for HD2. After that, everything wass like a charm
Hi,
my P3600 has a serious problem! I've flashed an Elegant Ed. (but I don't remeber the version). Now, I'd like to reinstall original ROM, but this is the results:
1) PC WIN VISTA: Activesync get ON, the PC see the PPC and the result is CONNECTED.
2) Incoming to update the PPC but the error IS 260 (communication error)
3) in the bootloader is indicated:
a) TRIN100 - IPL-0.50
b) TRIN100 - SPL-1.07.0000
c) serial
4) I downloaded [P3600i] HardSPL v1.1 and installs its on PPC and in bootloader there's (but error 260 continues to work )
a) TRIN100 - IPL-0.50
b) TRIN100 - SPL-3.10.Olimpo
c) PPC in bootloader config.
d) serial
5) Now, there's a SPL on my PCC !!! Connect and disconnect my USB cable by PPC, leaving PPC in bootloader configuration and by activesync disable "connect by USB"
6) insert usb cable in PPC, but it doesn't go to USB
..... I do not know what to do !!!!
Please help my
Junior
base167 said:
Hi,
my P3600 has a serious problem! I've flashed an Elegant Ed. (but I don't remeber the version). Now, I'd like to reinstall original ROM, but this is the results:
1) PC WIN VISTA: Activesync get ON, the PC see the PPC and the result is CONNECTED.
2) Incoming to update the PPC but the error IS 260 (communication error)
3) in the bootloader is indicated:
a) TRIN100 - IPL-0.50
b) TRIN100 - SPL-1.07.0000
c) serial
4) I downloaded [P3600i] HardSPL v1.1 and installs its on PPC and in bootloader there's (but error 260 continues to work )
a) TRIN100 - IPL-0.50
b) TRIN100 - SPL-3.10.Olimpo
c) PPC in bootloader config.
d) serial
5) Now, there's a SPL on my PCC !!! Connect and disconnect my USB cable by PPC, leaving PPC in bootloader configuration and by activesync disable "connect by USB"
6) insert usb cable in PPC, but it doesn't go to USB
..... I do not know what to do !!!!
Please help my
Junior
Click to expand...
Click to collapse
You have choice a wrong HardSPL !!!
Olipro 3.10 and 3.20 are for HTC P3600i and no working for TRINITY P3600.
So, now probabily you don't see "USB" on Bootloader when you connect you trinity on PPC.
Solution:
You must reload your H-SPL With SD CArd.
It's very simple:
searching for a Hard SPL for trinity device, example Olipro 1.20 and rename file "RUU_signed.nbh" ---> "TRINIMG.nbh".
Then copy file "TRINIMG.nbh" in a SD CARD and insert it on your Trinity; After that , make a Soft reset with stylus reset +power+camera.
Power bottom for update your Bootloader.
Now you would see your trinity working again
Davide

I think i've bricked my htc after flashing :( HELP plzzz

Hi guys
Originally i had a HTC touch pro 2 from Vodaphone with win6.1 i tried to put the new energy rom on by following the guide here:
(flashing via activesync)
http://forum.xda-developers.com/showthread.php?t=550540
with this
ROM:
EnergyROM_21876_RHOD500_24.Nov.2009_Standard
it goes past the start up screen "Touch pro 2" and then it stops on with a white background, at the bottom of there screen it displays
B 80
R 4.49.25.17
P 61.44tc.25.32U
D Energy ROM
the multi colour screen info shows
RHOD100 32M ss-BC
SPL -0.85.0liNex
MicroP(LED 0x0A
MicroP(KEY) 0x04
TURBO HW/TURBO SW
TP MFG DATA
508,533 800,851
800,208 209,208
217,852 CALIBRATED
can someone help me recover this plz its a new phone
Thanks in advance
once at that final screen,
plug in usb
once your computer has installed drivers, it will say usb instead of serial at the bottom of the phones screen.
try flashing again,if that fails try a different rom or redownload, its not bricked your at bootloader
if you still struggle use the search feature of this site, you will find everything you need
cheers steve
rosebud said:
once at that final screen,
plug in usb
once your computer has installed drivers, it will say usb instead of serial at the bottom of the phones screen.
try flashing again,if that fails try a different rom or redownload, its not bricked your at bootloader
if you still struggle use the search feature of this site, you will find everything you need
cheers steve
Click to expand...
Click to collapse
or try flash using SD card
Flashing Via MicroSD Card
1. Make sure your microSD is Formatted to fat32 (you dont have to delete all files but it is safer if you do)
2. Download your prefered Rom from the Rhodium Rom Develpoment Page and unzip/unrar it to your PC
3. Goto the Roms Folder and rename the .nbh file to RHODIMG.nbh
4. Copy the RHODIMG.nbh file to the root of your MicroSD Card
5. Plug the MicroSD Card into the phone
6. Enter the BootLoader screen, you will first see a tri-color screen with the phone and SPL Information at the top
7. Follow the On Screen instructions to start the update
8. After flash has completed, press the reset button with the stylus to reset the device.
cheers
indra9110
Pheeew thats a relief panic mode off now
Thanks rosebud and indra9110 for your fast replies, I got it working rosebud's way.
I downloaded the rom again and it works perfect now,
I've also got iskoot working (which was NOT working on the vodaphone 6.1 rom)
Thanks again guys
Glad to hear your phone has come back to life

[PROBLEM] Bricked my Blackstone

Hi All.
I've had my flashed severtal times with the new ROM and never had any problems with it (apart from ROM itself not being perfect).
Yesterday I've cooked myself a plain ROM and flashed phone with it. Flash took less than a minute and my phone isn't starting any more. I've checked NBH file and it's only 6 MB!
At the moment all I can do it to is to try to turn it on, it stops on the 'Smart Mobility' screen with red info on the bottom. Info reads:
R 1.14.25.24
G 52.64.25.34U
D 1.59.48753
When I start my phone with Vol Down button pressed it goes to tricolor and when I continue to hold Vol Down I get white screen with message: Loading: No Image File! showing on the screen briefly and back to tricolor.
No problem you say - flash another ROM. But at the moment my phone doesn't connect to my PC. Cable tested with another HTC - works. When I connect it I get USB on the screen but Flashing utility doesn't detect the phone.
When I try to Hard Reset the phone it just starts normally. So Vol Up + Vol Down + Power doesn't work at all. All I have is smart mobility and tricolor.
Info from Tricolor:
BLAC100 32M
SPL-1.56.OliNex
MicroP-Blackstone (LED) v6
and on the bottom either Serial or USB.
Question is:
is there anything I can do to revive my phone? Is there any way to flash it without USB connection? If yes, how do I do it?
Thanks in advance,
There is a way of flashing from SD card if you have HSPL (you do... OliNex).
Please do some search...
if it displays usb in tricolor you can flash a rom with CustomRUU from there. its not bricked
Put BLACIMG.nbh on the root of your SD card and enter bootloader mode, it'll detect it and ask if you want to flash it - press power button to confirm.
Dont connect your phone to your computer.
Hold down the Volume down button and hit the power button.
Your entering the tricolor boot screen and at the bottom the word "Serial".
Now connect you phone to your computer with te USB cable the word serial disappear and now it says USB.
Now you can normally flash/update your phone.
Thank for all your answers.
Problem still lasts, tried everything I could, including trying another computer. I've tried SD card flashing but couldn't get past tricolor. Everytime I tried all I got was No image file! and nothing.
In desperate act of dying I've went to my neighbour and borrowed his old Win XP laptop and it worked... Currently flashing new ROM to it.
What I cannot understand is why my computer (iMac running Windows on parralels), my laptop (Win 7) and my second laptop (Win Vista) couldn't detect the phone. I've succesfully flashed it before using all three machines, including virtualized Win 7 on my mac :/
Any ideas why it stopped working? I'll try to connect it again when ROM will be fully flashed and let you know.
Thanks for your help anyway.
Cheers,
Why don't you try shipped ROM, it may do the trick.
Get the original shipped ROM from HTC site or from XDA site.
Extract the content in some directory
Rename ruu_signed.nbh to BLACIMG.nbh and copy it on root folder of your SD card.
Now start your phone holding Vol down button.
Fingers crossed to to start flashing
Hi again.
I can confirm that due to flashing my phone with that odd 6MB ROM I could not connect it to any computer running Windows Vista or Windows 7. Strangely enough - it worked with Windows XP Professional. I have managed to flash my phone again on it using custom ROM from this forum.
Cheers,
yeramihi said:
Hi again.
I can confirm that due to flashing my phone with that odd 6MB ROM I could not connect it to any computer running Windows Vista or Windows 7. Strangely enough - it worked with Windows XP Professional. I have managed to flash my phone again on it using custom ROM from this forum.
Cheers,
Click to expand...
Click to collapse
Glad you got this sorted. As your issue is now rectified I'm closing this thread

Dopod D810 / Trinity p3600 stuck at wm6 boot screen

I I can clearly see that this is a known issue, I have tried to flash it via the bootloader (from holding power, camera and reset button) but every guide i have followed says that i need to connect it via activesync to do that, and i cant because windows doesnt detect it as a phone it just detects it as a "HTC usb sync".
I really am stumped on what to do.

Categories

Resources