Related
I have tested a few HTC Comm Managers(new black theme. Kaiser style) and low and behold non of them have the wifi working right. I cannot enable/disable it from the comm manager. Anybody find a real working one that does this? Even some that were claimed to be "FIXED" didn't work...
Anyone have a dump of the original also? (stock WM6)
I've got the same problem since the upgrade to WM6. Nothing works: soft-hard reset, upgrade... WLAN doesn't works (since comm manager).
me too...any solution mods?
Same problem here... The default WM6 HTC comm manager is working corectly.
anyone have a cab file of the original? incase i want to revert back to it?
You might find the fix here:
http://forum.xda-developers.com/showthread.php?t=326655&highlight=wing+10+button
What's wrong with it?
I'd tried to install http://forum.xda-developers.com/attachment.php?attachmentid=48832&d=1188607222
And then, the following message: "Installation was unsuccessful. The program or setting cannot be installed because it does not have sufficient system p ermissions"
...
When I try to do the change in registry, a new surprise: in the registry tree, after CommManager doesn't exist "WLAN", but numbers (0,1,2,3... and in 3 there's WLAN). The change in registry: NOT WORK YET!
I've found the problem (maybe...). In folder "Connections" there's not Wi-Fi icon... what it means?
pichetinhas said:
What's wrong with it?
I'd tried to install http://forum.xda-developers.com/attachment.php?attachmentid=48832&d=1188607222
And then, the following message: "Installation was unsuccessful. The program or setting cannot be installed because it does not have sufficient system p ermissions"
...
(
Click to expand...
Click to collapse
SAME THING HERE! No permission to do this! I hope this does not result in a hard reset.
OK, I finally got anew one installed. Even though I tried a fresh install after a reboot, I still couldnt get it installed. So, what I did was start commmanager, Bthen stop it in Settings > Memory > Active programs
REALLY A GENIE!!! I'll try it...
It's Ok! Now, I could installed the comm manager, but it doesn't work... What I must fix exactly?
This is exactly what I did:
- Step 1: Copy to the phone and run it.
- Step 2: (Fixing WLAN button malfunction, somehow it doesn’t work by default on Wing): **Thanks for beowulf6’s post for this fix.
Change "HKEY_LOCAL_MACHINE \SOFTWARE \HTC \CommManager \WLAN= "Windows WLanMgr.exe " "DeviceName" = "{98C5250D-C29A-4985-AE5F-AFE5367E5006} TNETW12345"
the end of this long String is the WLAN-Adaptername of the Device.
just change in this Example "TNETW12345" into "TNETWLN1"
-Step 3: (Fixing Wi-Fi setting launch issue) **Thanks for phatman81’s post for this fix.
Change "HKEY_LOCAL_MACHINE\SOFTWARE\HTC\CommManager\WLAN\ Default:"
\Windows\WlanMgr.exe --> \Windows\ctlpnl.exe
After all this... The WLAN icon is always off...
Nobody else has the same problem? It's incredible!! I begin to think that I've done something wrong. It has began after the upgrade to WM6... Now, I can't downgrade to WM5 because I don't have the rom WM5 original... :'(
That CommManager dosen't seem to work well. I had problems with it. I found another one that DID work though.
grizzley said:
That CommManager dosen't seem to work well. I had problems with it. I found another one that DID work though.
Click to expand...
Click to collapse
hi, can you please point me to where you downloaded this??
hello
i have the same problem. wifi card not run.
the problem? http://forum.xda-developers.com/showthread.php?t=322225
i d´nt know.
anyone a idea? thanks
Do a search. You will find that you have to edit the settings in the registry for the comm manager.
I have this same problem. If anybody has a cab file of the stock tmo com manager, please post it!
Thanks in advance!
You guys...
Go into the registry and find out what the name is for the wireless adapter is. Take that information and change the adapter that is shown in the comm manager.
Thats really all there is to it.
If youre going to screw with the software, youre going to need to blood on your hands. You cant just throw stuff on the phones and expect it to work.
All right...
On my wing
\\\registry\HKLM\Software\HTC\CommManager\WLAN\<DeviceName>
{98C5250D-C29A-4985-AE5F-AFE5367E5006}\TNETTWLN1
That is the adapter for my phone, might be the same for you.
If youre using the changable comm manager you will have to change the settings for the wlan setup.
\\\registry\HKLM\Software\HTC\CommManager\WLAN\<Default>
\Windows\WrlsMgr.exe
Once again might be different for you.
Im using TouchIT 2.3 my stuff might be different.
I GOT IT
pichetinhas said:
It's Ok! Now, I could installed the comm manager, but it doesn't work... What I must fix exactly?
This is exactly what I did:
- Step 1: Copy to the phone and run it.
- Step 2: (Fixing WLAN button malfunction, somehow it doesn’t work by default on Wing): **Thanks for beowulf6’s post for this fix.
Change "HKEY_LOCAL_MACHINE \SOFTWARE \HTC \CommManager \WLAN= "Windows WLanMgr.exe " "DeviceName" = "{98C5250D-C29A-4985-AE5F-AFE5367E5006} TNETW12345"
the end of this long String is the WLAN-Adaptername of the Device.
just change in this Example "TNETW12345" into "TNETWLN1"
-Step 3: (Fixing Wi-Fi setting launch issue) **Thanks for phatman81’s post for this fix.
Change "HKEY_LOCAL_MACHINE\SOFTWARE\HTC\CommManager\WLAN\ Default:"
\Windows\WlanMgr.exe --> \Windows\ctlpnl.exe
After all this... The WLAN icon is always off...
Nobody else has the same problem? It's incredible!! I begin to think that I've done something wrong. It has began after the upgrade to WM6... Now, I can't downgrade to WM5 because I don't have the rom WM5 original... :'(
Click to expand...
Click to collapse
If u wanna know your adapter go to
HKLM\comm\tcpip\linkage
mine is SDIO86861 and in linkage folder it is shown ppp SDIO86861
Hope this info helps u
[SOLVED!! look at the end of the thread]
hello,
i'm in real trouble.
the beginning of my trouble was:
i updated my kaiser with the new vodafone 6.1 rom.
from this point, i can't sync anymore...
i tried really everything what was suggested in google/forums and the forum here.
- hard-reset
- deleted reg-keys (partnership)
- uninstalled WMDC and installed real fresh
- rolled back to VPA Rom 6.0 and back to 6.1 because of the same problem
- tried every settings (advanced network mode)
- disabled firewalls
- .. and so on...
can't get rid of this f*** problem...!
any ideas?? i'll make a donation for the guy who can solve my problem without doing a fresh vista installation!
--> domain network! but there isn't any difference while syncing?
--> i can copy data to my VPA and reverse, explorer mode works fine!
--> Windows Vista x64 Ultimate
please can you help me?!
sorry for my bad english!
eventlog is showing:
- System
- Provider
[ Name] RapiMgr
- EventID 8
[ Qualifiers] 49152
Level 2
Task 0
Keywords 0x80000000000000
- TimeCreated
[ SystemTime] 2008-09-27T08:39:17.000Z
EventRecordID 32699
Channel Application
Computer E6850-Core2Duo.xxxxx.xxxxx.de
Security
- EventData
communication (0x80072745)
at the wmdc.log file:
wmdc Error: 6 : [null] Caught exception: System.Runtime.InteropServices.COMException (0x80004005): Beim Aufruf einer COM-Komponente wurde ein HRESULT E_FAIL-Fehler zurückgegeben.
bei Microsoft.WindowsMobile.IActiveSyncEngine.GetDataTypeArray(String partnerID)
bei Microsoft.WindowsMobile.DeviceManager.ActiveSyncEngine.<LoadDataTypeList>b__5()
DateTime=2008-10-21T12:08:58.8656855Z
wmdc Verbose: 0 : NewPartnershipWizard ended becuse of an exception
garfield2412 said:
hello,
i'm in real trouble.
the beginning of my trouble was:
i updated my kaiser with the new vodafone 6.1 rom.
from this point, i can't sync anymore...
i tried really everything what was suggested in google/forums and the forum here.
- hard-reset
- deleted reg-keys (partnership)
- uninstalled WMDC and installed real fresh
- rolled back to VPA Rom 6.0 and back to 6.1 because of the same problem
- tried every settings (advanced network mode)
- disabled firewalls
- .. and so on...
can't get rid of this f*** problem...!
any ideas?? i'll make a donation for the guy who can solve my problem without doing a fresh vista installation!
--> domain network! but there isn't any difference while syncing?
--> i can copy data to my VPA and reverse, explorer mode works fine!
--> Windows Vista x64 Ultimate
please can you help me?!
sorry for my bad english!
eventlog is showing:
- System
- Provider
[ Name] RapiMgr
- EventID 8
[ Qualifiers] 49152
Level 2
Task 0
Keywords 0x80000000000000
- TimeCreated
[ SystemTime] 2008-09-27T08:39:17.000Z
EventRecordID 32699
Channel Application
Computer E6850-Core2Duo.xxxxx.xxxxx.de
Security
- EventData
communication (0x80072745)
at the wmdc.log file:
wmdc Error: 6 : [null] Caught exception: System.Runtime.InteropServices.COMException (0x80004005): Beim Aufruf einer COM-Komponente wurde ein HRESULT E_FAIL-Fehler zurückgegeben.
bei Microsoft.WindowsMobile.IActiveSyncEngine.GetDataTypeArray(String partnerID)
bei Microsoft.WindowsMobile.DeviceManager.ActiveSyncEngine.<LoadDataTypeList>b__5()
DateTime=2008-10-21T12:08:58.8656855Z
wmdc Verbose: 0 : NewPartnershipWizard ended becuse of an exception
Click to expand...
Click to collapse
Which operating system are you trying to sync with?
First thing you can try is to go start, settings, connections, usb to pc and then untick "enable advanced network functionality"
let me know if that works or not I will give you something else to try.
1.Why don't you try another rom eg a hyperdragon's one.
2.Have you tried more than one pcs to synchronise with? Maybe you have problems with your pcs operating system
If still a problem might be a defective usb port.
Does WMDC even acknowledge your Kaiser?
Launch WMDC from the Control Panel, and then then connect your phone. Do you see "Connecting" pop up for even a second before switching back to "Not Connected"?
If nothing else has worked so far try this:
Go to Device Manager, delete the "Portable Device" keys, then go to c:\windows\inf folder (Make sure you can view hidden folders). Next, find the oemxx files until you find the one that has "Windows Mobile Smartphone" in it. These are numbered sequentially for each device you add, so you'll have to do a bit of digging before you find the right one. Once you find it, delete it and the corresponding .pnf file. Once you've done this, reboot your computer and reconnect your device and it should reinstall. Be sure to make copies of the files just in case you delete the wrong ones.
thank you very much for answering so fast!
answers to your questions:
-Which operating system are you trying to sync with?
--> Vista x64 Ultimate
- First thing you can try is to go start, settings, connections, usb to pc and then untick "enable advanced network functionality"
--> tried a couple of times ticked and unticked --> only gives back different rapimgr fault codes, but still no sync
defective UDB --> trided different cables and ports
connection to kaiser works very well (without sync)!
--> can see my kaiser in explorer an can copy files!
only syncing does not work :-(
mskip said:
If nothing else has worked so far try this:
Go to Device Manager, delete the "Portable Device" keys, then go to c:\windows\inf folder (Make sure you can view hidden folders). Next, find the oemxx files until you find the one that has "Windows Mobile Smartphone" in it. These are numbered sequentially for each device you add, so you'll have to do a bit of digging before you find the right one. Once you find it, delete it and the corresponding .pnf file. Once you've done this, reboot your computer and reconnect your device and it should reinstall. Be sure to make copies of the files just in case you delete the wrong ones.
Click to expand...
Click to collapse
tried to change drivers in device manager about 3 days ago.
i have
HTC USB Sync
version 6.0.6001.18000 21.06.2006 and
version 6.1.6965.0 31.05.2007
tried to change this in device manager but both drivers won't sync.
but both drivers connect very well!
registry needed
can anybody post his regystry-keys for:
HKEY_LOCAL_MACHINE\SOFTWARE\Microsoft\Windows CE Services
??
thank you!
maybe there is a bug in my machine!
idea. these keys are empty at my machine!
[HKEY_LOCAL_MACHINE\SOFTWARE\Microsoft\Windows CE Services\SpecialDefaults]
[HKEY_LOCAL_MACHINE\SOFTWARE\Microsoft\Windows CE Services\SpecialDefaults\CEDevice]
[HKEY_LOCAL_MACHINE\SOFTWARE\Microsoft\Windows CE Services\SpecialDefaults\CEDevice\Services]
[HKEY_LOCAL_MACHINE\SOFTWARE\Microsoft\Windows CE Services\SpecialDefaults\CEDevice\Services\Synchronization]
[HKEY_LOCAL_MACHINE\SOFTWARE\Microsoft\Windows CE Services\SpecialDefaults\CEDevice\Services\Synchronization\Objects]
[HKEY_LOCAL_MACHINE\SOFTWARE\Microsoft\Windows CE Services\SpecialDefaults\CEDevice\Services\Synchronization\Objects\File]
"Settings"="MS.WinCE.CEFStore.InplaceUI"
@="CEFStore Data Object"
Do you have HardSPL installed on your phone so you can try flashing a non stock rom? Alot of the sync problems on stock roms are fixed by the chefs when they cook their own roms. Look at the links in my sig for some threads to look at.
mskip said:
Do you have HardSPL installed on your phone so you can try flashing a non stock rom? Alot of the sync problems on stock roms are fixed by the chefs when they cook their own roms. Look at the links in my sig for some threads to look at.
Click to expand...
Click to collapse
i thought about it...
but worrying about: why does WM 6.0 and WM 6.1 rom work anymore?
flashed back to WM 6.0 (asked vodafone for it!!) and the problem is there anymore?
i've read a litte bit about hardspl and flashing...
is it very difficult?
Guten Aben!
Any chance you can redo your Vodaphone update from a good XP machine? Sometimes it works when Vista doesn't.
It only needs to download Activesync from Microsoft's website if it doesn't have it already.
This happened to me a long time ago, it turned out that rebooting Windows PC after changing the network settings worked, just like in the old Win98 days. I am referring to the Activesync network setting.
For some reason the realtime registry edits for networking wasn't so realtime!
Good luck friend!
joihan777 said:
Guten Aben!
Any chance you can redo your Vodaphone update from a good XP machine? Sometimes it works when Vista doesn't.
It only needs to download Activesync from Microsoft's website if it doesn't have it already.
This happened to me a long time ago, it turned out that rebooting Windows PC after changing the network settings worked, just like in the old Win98 days. I am referring to the Activesync network setting.
For some reason the realtime registry edits for networking wasn't so realtime!
Good luck friend!
Click to expand...
Click to collapse
trying that tomorow..
my brother has an XP and Vista machine..
also thinking about checking his and mine HLKM\Windows CE keys...
garfield2412 said:
i thought about it...
but worrying about: why does WM 6.0 and WM 6.1 rom work anymore?
flashed back to WM 6.0 (asked vodafone for it!!) and the problem is there anymore?
i've read a litte bit about hardspl and flashing...
is it very difficult?
Click to expand...
Click to collapse
No its not difficult at all.
Read this guide I made for Flashing your First Rom its helped alot of people out and the steps are easy to follow
The guide has steps for flashing from MicroSD Card too if you dont trust Vista.
Try this. I ran into issues syncing with my Vista Ultimate x64 machine when running a particular cooked ROM, and this CAB fixed it for me.
I hate to ask such a mundane question, but you are running in administer mode with full access, right?
You can also check out this site http://www.pocketpcfaq.com/faqs/wmdc/connectoverview.htm
SOLVED!
hy,
okay, first of all i have to thank everybody who wanted to help me!
but all things you suggested to me: i tried i weeks before i opend this thread.
i wasn't able to solve my problem --> donation aquired...
but i figured it out on my own (now, months later, one day later i opened this therad ).
but i think the soloution can help many users who whave sync problems ant the rapimgr 0x00... problem!
remembered that i had sync problems years ago under XP with an PPC2002 machine when copyied the sync.-profile from one machine to the other.
i remembered the HLKM\Windows CE reg keys!
i asked my brother for his HLKM\Windows CE reg keys! (you remember i asked in this thread also)!
checked the keys with mine and figured out, that my keys where completely different and many keys are missing!
i exported my reg keys and deleted them in the registry. (HLKM\...\Windows CE (look in ahead and you know whitch keys i'm meaning)) --> backup
then i imported the reg HLKM\Windows CE keys from my brother !
conected my VPA and TADAAAAAAA, working!!!!!!!!!!!!!!!!!!
i think this can be another soloution for all guys who have problems with sync and an reinstall of WMDC dosn't do the trick!
wondering why an reinstallation of WMDC doesn't create the HLKM\Windows CE keys correctly???
thanks a lot for your ideas, even when they didn't help.
Glad you fixed it, if you can provide me with more details of the keys and values you changed i can test it out and make a cab to possibly help other people in the future
mskip said:
Glad you fixed it, if you can provide me with more details of the keys and values you changed i can test it out and make a cab to possibly help other people in the future
Click to expand...
Click to collapse
okay, i'll zip two .reg files (PC-Side). my "not working reg" and "working reg keys" from my brother that i imported.
i think WMDC is calling some dlls. when they aren't in the registry WMDC gives you a strange answer back...
still the question: why does a reinstallation of WMDC do not create these keys?
maybe these parts are interesting:
[HKEY_LOCAL_MACHINE\SOFTWARE\Microsoft\Windows CE Services\SpecialDefaults\PocketPC\Services\Synchronization]
[HKEY_LOCAL_MACHINE\SOFTWARE\Microsoft\Windows CE Services\SpecialDefaults\PocketPC\Services\Synchronization\Objects]
okay, here they are:
garfield2412 said:
okay, i'll zip two .reg files (PC-Side). my "not working reg" and "working reg keys" from my brother that i imported.
i think WMDC is calling some dlls. when they aren't in the registry WMDC gives you a strange answer back...
still the question: why does a reinstallation of WMDC do not create these keys?
maybe these parts are interesting:
[HKEY_LOCAL_MACHINE\SOFTWARE\Microsoft\Windows CE Services\SpecialDefaults\PocketPC\Services\Synchronization]
[HKEY_LOCAL_MACHINE\SOFTWARE\Microsoft\Windows CE Services\SpecialDefaults\PocketPC\Services\Synchronization\Objects]
okay, here they are:
Click to expand...
Click to collapse
thanks i will have a look at them tonight
i am having the same problem except with windows XP and active sync 4.5
the odd thing is that it worked fine a month ago. i havent changed my ROM, installed/uninstalled anything on my phone. my computer, is a different story, i did install office 2007. i hadnt synced my phone for a month, so i decided it was about time. i connect via USB, and i get nothing. not even a little sound saying a device was connected. the phone charges but thats about it.
i have tried, muliple computers, multiple USB ports, multiple wires. I did a hard reset. And i finally tried the registry keys on this thread. still doesnt work. any ideas?
**i have also check/unchecked the "enable advanced network functionality" box
Dear all:
I have made another 20279 rom for wings(s730). I found the S740'S office rom ( 1.14.707.0) from this link http://forum.xda-developers.com/showthread.php?t=441674.And it contain all chinese and english language,so i made our ROM over again.
What's new:
1,full new office 20279 sys
2,full oem from 1.33 707 1(office rom found by hikey)
3,cn&en language,cn default
4,New RADIO 1.60
5,system optimization(unlock,accelerating system-you can feel your phone as if it have wings because it is very fast )
Download from it:
http://www.rayfile.com/files/14ecb868-b3bc-11dd-9067-0014221b798a/
More informations view this link: http://www.ioicn.com.cn/forum/thread-304244-1-1.html
Sorry , I dont know how to insert a link and images.
Who will help me?
Mirror
Ive Created A Mirror For This Rom Due To The Difficulty Ive Just Had Downloading It.
Heres The Mirror Anyway...
http://www.mediafire.com/file/z0yzm3gyuon/RUU.rar
Hey xucue,
Both links doesn't seem to work here.
The downloadlink gives me a page with much chinese characters. I tried de red button but this doesn't work.
Would you post te correct links or maybe upload it to another server?
Thank you.
ps: wat is te free ram?
Oh sorry OllieD's,
Didn't see your your post.
Think this page was in my cache memory.
Downloaded, tried unsuccessfully, get stuck on 19% and then gives me 262 error, after that bricks the phone. To get the phone back, had to reflash with original htc firmware. Tried 2nd time with another way, no success stays at 0%, i mean without running sspl. Am i doing something wrong?
thanks for your link,dear dllied.
to update the rom,you have to make sure your wings' spl is 0.91.
i have test it,and it work well,so i share it to all.
available ram is same to office 6.0.
in my other rom,the available ram have 20 with sd card after flash rom.but it is only contain chinese language.
Yes i have spl 0.91, Had it since update with Alcaline's rom. But still same stuff.
rom is running! battery load over usb is disabled - go to settings an change it. every thing is ok!
i wonder why there is no rom with phonecanvas 2g for wings. also, why is the original s740 weather gone?
but: rom is cool and fast!
many thanks
ok tell me if i am doing something wrong in steps:
1. Unlock the device with sda-unlock
2. Backup-just in case.
3. Put spl-0.91-wings on the phone and run it, accepting everything, then when it says usb, unplug and replug usb cable
4. Run Rom updateutility.exe on pc
Then it goes up to 19% everytime and gives me 262 error. Triying recovery because phone boots to 3 colour mode, as there is no rom in it. Says recovery successful. The flashing again, stays at 0% then gives mee same 262 error.
Then the only way to get the phone back is to flash with original htc firmware. So what am i doing wrong?
may this helps: my ROMUpdateUtility wasn't right. take the nbh and put it in a folder with another one - from an another rom!
Is there any way to get the eT9.Wings.0414.kmap.txt included in this rom? I need the keymapping for norwegian language..!
Zeerocool said:
Is there any way to get the eT9.Wings.0414.kmap.txt included in this rom? I need the keymapping for norwegian language..!
Click to expand...
Click to collapse
I need it too...
NeoID said:
I need it too...
Click to expand...
Click to collapse
I found the answer! Just add the norwegian keymap in the windowsfolder!
SimonKnight6600 said:
I found a german keyboard layout file for the wings: http://pocketpc.ch/showpost.php?p=217070&postcount=7 It also adds support for keys like ä, ü and ö.
Just copy the file into the windows directory of your S730. Then open your favourite registry editor, go to HKEY_LOCAL_MACHINE/SOFTWARE/Tegic/eT9/IME/KeyboardLayoutDlls and change the value of 000007FF to eT9.Wings.0407.kmap.txt.
HTH
Click to expand...
Click to collapse
Zeerocool said:
I found the answer! Just add the norwegian keymap in the windowsfolder!
Click to expand...
Click to collapse
Thanks.. I've made a backup from my HTC... if you want it, here it is..
[HKEY_LOCAL_MACHINE\Software\Tegic\eT9\IME\Keyboard LayouDlls]
Change the value of: "000007FF" to eT9.Wings.0414.kmap.txt
Click to expand...
Click to collapse
Is there anything special I have to do in order to be able to flash my S730 with this rom? I see that some people had problems with it..
@Zeerocool, do you like the rom? Recommended to upgrade from Alkaline's build?
Ok, i think i am unlucky. Done evrything that i possibly could think of. Tried putting .nbh file into different rom update folders - no success, tried changing updateromutility.exe from various roms, tried customruu - no success, tried renaming .nbh file into latin only letters - no success. Tried with 3 different Windows systems: XP, Vista and 7. 2 different pcs. This just doesnt work, gets stuck on 19% always, all other roms upgrade fine, but not this one. Please help.
nice one, quick and stable.
I remade SlidingPanel CPRs to support Calibri,
1) install Calibri mod by NRGZ first
2) copy CPRs to your \Windows folder (replace existing)
I also add BaseHue and ClearType apps I found lacking
Also, I made my own Home layout without Profiles (you can easily access via On/Off key) and with compressed size for speed
I add regedit for your convenience, here are the mods you might like:
* HKEY_CURRENT_USER\ControlPanel\SoundCategories\CallStart to 0
* HKLM\System\GDI\GLYPHCACHE\limit to 65535 (tweak)
* HKLM\System\Inbox\RecipientAutoComplete and set/change the following DWORD: MaxSuggestions=4 (for example)
oh, and you can run Security app to all off so that you can rearrange Windows folder without restrictions + batterymeter that is a line on display top + reboot option added to On/Off button menu
all in the ZIP attached
+ I give you a new desktop theme, just place scheme in Application data/home and pics in \Windows
Finally success.
I am posting this info because I need some assistance in getting it to work perfectly I was hoping some of you out there may have some additional insight! thank you
Known Bugs/Issues
1. Incoming Call are directed direct to Voice mail
2. Speaker and Mic are defaulted to off you must enable
3. headset is default off you must first enable speaker then plug in headset
4. if any sound is activated while on a call Headset, Speaker, Mic are automaticly Disabled
HTC SHIFT FULL PHONE
I don't think it is currently need but I have also inclued the hardsspl for CDMA
Be careful with the RealVGA bit if you haven't got an English machine - I have so I couldn't test this bit - I inferred the solution from one of Daniel's posts.
1. Reset SnapVue if you have been hacking it.
- Run Clearstorage.exe (or Settings, Clear Storage)
- Disable Wi-Fi in Vista (Communication Manager)
- Enable Modem
2. Get Access to WM6
- In SnapVue, click Outlook E-mail
- Click Menu,New
- Click Menu,New,Insert Picture
- Where it says "My Pictures", click and navigate to "Windows" directory
- Highlight (using arrow keys) the "Start Menu" directory and copy it (using ctrl-c)
- Navigate into "Settings" directory in "Windows" and paste (ctrl-v). Ignore the calendar error.
- Click Ok and go back to SnapVue.
- Click Settings button and then "Start Menu, Programs, Internet Sharing"
- Click "Connect". The screen will say "Check USB cable.". Switch over to Vista and make sure that you have a network connection.
- Switch back to snapvue and click disconnect.
- Switch back to Vista and open Windows Explorer. From the "Computer" level, keep pressing F5 until you see Pocket_PC.
- Using "Tools, Folder Options" (alt T,O), click on the View tab and make sure that "Hide protected operating system files (Recommended)" is NOT enabled.
- Copy "RegistryEditor.exe" to "Pocket_PC,"\" directory.
- Still on Vista side, Using "Communication Manager", Click "Advanced Settings" and then "Reset Snapvue". Click OK.
- Switch to snapvue and wait for it to start up. If you miss the warning to allow running "RegistryEditor.exe", don't worry - click setting, Start Menu, Programs, File Explorer, then navigate to Windows, StartUp and run it from there.
- In RegistryEditor.exe, navigate to HKEY_LOCAL_MACHINE, Services. Delete the "SnapVue" entry. Click and hold the "SnapVue" entry until the context-sensitive menu appears, then select delete.
- Navigate to HKEY_CLASSES_ROOT\Cabfile\Shell\Open\command and change the default value to wceload.exe "%1" /nodelete - there is a space after the .exe and before the /nodelete here
- Close RegistryEditor.exe.
- In File Explorer, delete the PKG.exe and BlockTitleBar.exe files from the Windows\StartUp directory.
- Switch back to Vista and reset snapvue from Communications Manager's Advanced Settings.
- Switch back to SnapVue. When it has finished starting up and you have closed RegistryEditor, you will notice that you have the start menu at the top left of the screen.
- Tidy up - reset and delete "Start Menu" from the "Windows, Settings" directory
Pat yourself on the back! You have successfully converted the HTC shift's SnapVue to WM6.
2a. Enable all the hidden "Today" items
- Switch to WM6
- Click "Start Menu (icon at top left of screen), Programs, Internet Sharing"
- Click "Connect". The screen will say "Check USB cable.". Switch over to Vista and make sure that you have a network connection.
If not - go to Vista Connection Manager and stop and start the modem.
- go back to snapview disconnect and then connect again
- switch back to Vista
- Switch back to snapvue and click disconnect.
- Switch back to Vista and open Windows Explorer. From the "Computer" level, keep pressing F5 until you see Pocket_PC.
- In Vista, install and run ceregedit_setup.exe
- Press F1 to connect to WM6
- Use Tools, Unlock Registry to enable the import
- Use Edit, Import to import "today.reg". Ignore any errors.
- Close ceregedit
- Switch to WM6
- In "Start Menu, Settings, Today, Items", pick the today items you want to display.
3. Change the display resolution to 96 dpi (BE SURE THAT THE CHECK BOX FOR DISABLE PHONE SKIN IS CHECKED)
A word of warning - this version of RealVGA is English and does not work very well with non-English systems.
- If you have a non-English version of the Shift, then you will not have a directory called \Windows\StartUp. Before doing the rest of this section, you should create a "StartUp" directory in your Windows directory and copy all of the files from your language equivalent of StartUp.
- Switch to WM6
- Click "Start Menu (icon at top left of screen), Programs, Internet Sharing"
- Click "Connect". The screen will say "Check USB cable.". Switch over to Vista and make sure that you have a network connection.
If not - go to Vista Connection Manager and stop and start the modem.
- go back to snapview disconnect and then connect again
- switch back to Vista
- Switch back to snapvue and click disconnect.
- Switch back to Vista and open Windows Explorer. From the "Computer" level, keep pressing F5 until you see Pocket_PC.
- Copy "RealVGA_11.CAB" and "ResPack96dpi.ARM.CAB" to "Pocket_PC,"\" directory.
- Switch over to WM6
- From File Explorer (Start Menu, Programs, File Explorer), navigate to the top directory (using Up button as necessary)
- Install RealVGA_11.CAB accepting the security warning
- Install ResPack96dpi.ARM.CAB accepting the security warning and select ok to restart the system
- Run RealVGA from Start Menu, Programs
- Change to 96dpi and press OK and wait while the system restarts
- Tidy up - Using "Start Menu, Settings, System, Remove Programs" remove WM6_RealVGA (its job is done)
- In File Explorer, delete the 2 CAB files.
hkey_local_machine\system\state\phone
block voice MO call Change Registry from 1 to 0
CONGRATULATIONS!!!!!
Voice Calls are now enabled with working mic and speaker through headset also speaker phone works
1. Incoming Call are directed direct to Voice mail
2. Speaker and Mic are defaulted to off you must enable
3. headset is default off you must first enable speaker then plug in headset
4. if any sound is activated while on a call Headset, Speaker, Mic are automaticly Disabled
Side Note: you may want to also adjust these entrys as well
these will give you access to the phones menu options
hkeylm\software\oem\phonesetting
change all keys that begin with hidden from 1 to 0
hkeylm\controlpanel\phone
delete the Redirect key
Here's a link for everything you need
http://rapidshare.com/files/236022979/CDMA_Shift_Phone.rar.html
http://rapidshare.com/files/210940637/CDMA_Shift_Phone.rar.html
'This file is neither allocated to a Premium Account, or a Collector's Account, and can therefore only be downloaded 10 times.
This limit is reached.
To download this file, the uploader either needs to transfer this file into his/her Collector's Account, or upload the file again. The file can later be moved to a Collector's Account. The uploader just needs to click the delete link of the file to get further information.'
Link is down. Only ten downloads till it expired. Please post to a premium rapidshare account or send the download link again and I will post for you.
link has been updated
cybericebyte said:
link has been updated
Click to expand...
Click to collapse
Thanks much, downloading now !
Trashed Snapvue
I ran the CustomRuu from the zip file you posted, and managed to get into a loop where Windows Mobile will not boot. I can get into the bootloader with tools I downloaded on XDA, but have not found a ROM that will install without an error. Do you have a CDMA compatible ROM or even the original ROM that comes with the device. Will dive into the box to see whats on the disks next.
Need help though.
the orginal rom should be included in the zip folder
ShiftCDMAFLASH is the folder that I flashed (successfully) that left me in bootloader (three color screen).
RUUNBh is in the upper middle of the screen
CLI 0200
SPL 0.14.000
appear below, and USB in a white box appears below that.
The ShiftCDMAFLASH.zip file contains a different nbh rom file from the folder above, but I cannot get past 0% on the loader screen. I have used ecshift.exe -bl to get back in bootloader mode and hard resetted the Windows mobiel side, but no luck yet. Any suggestions ? +
just give it time
The 0.19 nbh file give a 262 error
On the other hand I can flash the 1.14.651.1 Rom with no trouble but I reboot (even after a hard reset) into the tri color screen with USB on the screen as listed above. Stalled in this mode.
Any other options ? or roms that might work. The GSM roms on XDA also crash out so I am locked in the 1.14.651.1 bootloader mode.....grrrr.
Is there another option I am missing ? I also tried the Snapvue reset program for Vista from the HTC website
Snapvue Software version 1.14.651.1
Snapvue Software version 1.14.651.1 is the one that I installed on my CDMA shift and now cannot get out of bootloader screen (tricolor) despite hard resetting the WM side. I am able to reflash the above listed rom with no errors. But still end up in the bootloader screen.
No other posted rom on XDA will load (probably due to GSM/CDMA differences). Do you have an alternative CDMA rom I could use or is there a way to get out of the bootloader and force WM to load that I am missing ?
use mtty should be posted on site
Used mtty
Thanks. I had been usimg mtty. I can successfully hard reset but WM boots back into the tri color bootloader screen following hard reset. lol. Still stuck. Thanks for the suggestion though.
now do ecshift mode 0 then mode reset
cybericebyte said:
now do ecshift mode 0 then mode reset
Click to expand...
Click to collapse
Thanks, I have been doing all of the above. Restarts into the tricolor screen. I can reformat with the rom you provided. Still tricolor on hard reset. Something in the rom is preventing wm from loading. Anything else left to do ?
I am probably going to need to give up. The snapvue side is toast. Unless there is someone with the original CDMA Rom out there willing to post online (even HTC) I do not think I can make this work.
Original CDMA ROM
Hello, I had exactly the same problem, my SnapVue stood in bootloader...
CMONEX gave me a ROM for CDMA Shift (I think is the original), it worked for me
you can download it from here:
http://srmpro.gas.pemex.com/video/R....30.00_1.33_PRL60711_SHIP_MO_Disable_PPST.exe
this link wont be available forever, if you can download and upload it to a site like megaupload it will be great!
hope this helps
rafaelc said:
Hello, I had exactly the same problem, my SnapVue stood in bootloader...
CMONEX gave me a ROM for CDMA Shift (I think is the original), it worked for me
you can download it from here:
http://srmpro.gas.pemex.com/video/R....30.00_1.33_PRL60711_SHIP_MO_Disable_PPST.exe
this link wont be available forever, if you can download and upload it to a site like megaupload it will be great!
hope this helps
Click to expand...
Click to collapse
Quick response thanks. Will try it out today and post my results. I did download and reupload to rapidshare. Here is the link.....
http://rapidshare.com/files/2374198....30.00_1.33_PRL60711_SHIP_MO_Disable_PPST.exe
I hope CMONEX is okay with that.
Was able to get Snapvue up and running with the exe file listed above. Did not need to do anything else. Thanks for posting. Will need to be more careful when testing new roms.
nmhusa said:
Was able to get Snapvue up and running with the exe file listed above. Did not need to do anything else. Thanks for posting. Will need to be more careful when testing new roms.
Click to expand...
Click to collapse
Excelent!
you are right, but that kind o things is part of the learning process
Thanks again for all the help.
Also managed to fix the Font sizes in Snapue via registry edits so that they increase in proportion to the scaled screen resolution with RealVGA. Until I figure out how to HardSPL the CDMA Shift and cook a custom rom, this will have to do.
when entering in BL mode the device
USB\VID_0BB4&PID_00CE\5&2EEFBCF&0&3
(Qualcomm CDMA Technologies MSM) doesn't get a driver from Windows Update and the ruu can't communicate with the device.
Where can I find such driver (the one for windows vista should work)
Thank you.
Install Windows Mobile Device Connect (WMDC) v6.1 first.
obviously I already did it.
The device connects, the ruu gets the rom version, the user hits next, the device enters in bl mode, after that the usb device attached changes to qualcomm.....and for that device the driver doesn't exist.
Mine went through fine using windows 7... Didn't need to install anything different or anything?!
Update using microSD is faster. Just unpack the rom package *exe & rename ruu_signed.nbh > RHODIMG.nbh > Copy to microSD root > Enter bootloader > Push power button > Wait > Soft Reset > Happy! (Just in case u forgot the step )
lovelldr said:
Mine went through fine using windows 7... Didn't need to install anything different or anything?!
Click to expand...
Click to collapse
What did you do?
I simply attached the rhodium.
Windows downloaded automatically the device center 6.1 from windows update and installed it (along with the driver "generic rdnis" or something like that) and the pc recognized the phone. On xp you have to download manually activesync..but with seven everything was automatic...
I also tryed to uninstall wmdc and do it again..same results...
(Win 7 Home Premium RTM 6.1.7600)
Thanks for remembering me the steps for sd flash..but does this reset the phone? I'm actually using custom ruu (I'm just flashing the radio hotfix and I don't want to lose my data)
LinoX said:
Thanks for remembering me the steps for sd flash..but does this reset the phone? I'm actually using custom ruu (I'm just flashing the radio hotfix and I don't want to lose my data)
Click to expand...
Click to collapse
Your data is safe. Depends on RHODIMG.nbh u r trying to flash. In bootloader, u will see a list of existing images like splash,os, radio, etc.
If u r flashing radio image only, then ur data is safe. I did it a few days ago
Thank you...
I have another problem on Win7 : CustomRUU ask for the root permission then create usual files in its folder and finally theses files disapear, and that's all... I don't get any CustomRUU window
I have already :
-installed WMDC
-activated the .NET framework in the config panel (don't know if it's enough but usual installation files told me to do it...)
-uninstalled my antivirus software
-tried some compatibility modes...
Am I doing smth wrong ?
Aurel143 said:
I have another problem on Win7 : CustomRUU ask for the root permission then create usual files in its folder and finally theses files disapear, and that's all... I don't get any CustomRUU window
I have already :
-installed WMDC
-activated the .NET framework in the config panel (don't know if it's enough but usual installation files told me to do it...)
-uninstalled my antivirus software
-tried some compatibility modes...
Am I doing smth wrong ?
Click to expand...
Click to collapse
I just had this exact same problem when I tried to update the latest energy rom. When unzipped to a folder it had % signs and 2050 in the name of the folder. I just renamed the folder to energyrom without the % signs and it loaded the rom normally. With % signs in the name the program could not find its own location and terminated.
Hope this helps
derekcranson said:
I just had this exact same problem when I tried to update the latest energy rom. When unzipped to a folder it had % signs and 2050 in the name of the folder. I just renamed the folder to energyrom without the % signs and it loaded the rom normally. With % signs in the name the program could not find its own location and terminated.
Hope this helps
Click to expand...
Click to collapse
The reason it had issues is because in Windows when you use %foldername% it thinks that it is a system variable. You should really change the settings on the program you use to decompress things. This is a really bad thing to have set.
Hm stupid error isn't it ? Thank you guys