Hi, I have a problem. I recently flashed my G3 Cingular 8125 to IPL 1.05 (The Xda_MiniS_LaunchROM_v154102.exe) so that I could CID unlock it and because I had a crash, which resulted in my phone to freeze everytime it reached the screen that said Windows Mobile 5. Before the flash, I could only connect my phone to my PC when it was in Boot mode, I hoped everything would be OK after that.
But it's not!
The phone runs OK now, everything works, except when I try to connect it to my PC. The second ActiveSync starts connecting to the phone, it freezes and needs a Soft Reset to get back up.
So here are the questions:
1) what could be the reason for these freezes?
2) How do I fix it?
3) If I don't succeed in fixing it, can I CID unlock it, if it is connected to my PC, but only in BOOT mode?
Thanks!
Related
Hi folks,
Very strange: I tried to connect to the PC with ActiveSync 4.1 and the BA in the bootloader mode. Didn't connect. Tried a couple of times, reinstalled AS etc. No chance.
Therefore I wanted to be sure, there is no connection problem, I started the MAUpgrade tool, which connected successfully and showed the EPROM versions on the screen. So I started the upgrade procedure, as expected the BA went in the bootloader mode, but as before, from there nothing went on - it was not recognised by the PC or AS.
The strange story about it is, I connected very easily in the normal mode, I upgraded already in the past successfully ...
BUT NOW I'm really in trouble, because I can't exit anymore the bootloader mode. I tried a hard and soft reset, I have removed the battery for 10 minutes .... Now way, the sceen is always in bootloader. If I put the device in the cradle, it recognizes this, by showing USB, without cradle, its Serial. The bootloader shows the version 2.08
Shoud I replace the device and enquire with my provider for a new one?
Thanks and looking forward to hear from you, Alexander
I posted a question last week and I was installing the ROM and windows crashed. My phone now has the bootloader screen (colored screen with USB in the corner). I had already upgraded to 2.17 which was fine. Any thoughts?
If you can still access the bootloader you have not fried your phone. Get it into bootloader - plug in your USB and connect to your PC and run the ROM upgrade again. If it fails again check the ROM is a good version ( re-download if your not sure) Failing that, do the process on a different PC.
BTW you do not need to run Activestink on the PC.
Best of luck :lol:
Hi, I flashed my Herald with WM6 ROM by ASerg, and it fails. Now after hardreset it loading only white screen with some beep (after startup screen with logo) and thats all.......my problem is simple - I can go to bootloader mode, but in bootloader, when i want to re-flash to another ROM, i can't connect it with PC. It showed USB in bootloader screen, but activesync dont want to synchronize and every flashing method showin' warrning NO DEVICE CONNECTED. i know, that herald is connected, pc warned me by beep that new hardware is connected, bud activesync no....how can i fix it ? please help.....thx
P.L said:
Hi, I flashed my Herald with WM6 ROM by ASerg, and it fails. Now after hardreset it loading only white screen with some beep (after startup screen with logo) and thats all.......my problem is simple - I can go to bootloader mode, but in bootloader, when i want to re-flash to another ROM, i can't connect it with PC. It showed USB in bootloader screen, but activesync dont want to synchronize and every flashing method showin' warrning NO DEVICE CONNECTED. i know, that herald is connected, pc warned me by beep that new hardware is connected, bud activesync no....how can i fix it ? please help.....thx
Click to expand...
Click to collapse
Try to falsh with RUU - it should work without active sync. Because in bootloader it connects BUT not via activesync.
Good luck
papamopps said:
Try to falsh with RUU - it should work without active sync. Because in bootloader it connects BUT not via activesync.
Good luck
Click to expand...
Click to collapse
Dear user
I have same problem
I try via RUU
but the problem not solved !
how can i do?
Thanks
Hello!
I have this problem:
I've installed WM6.5 on my Trinity, and it worked well, but today I wanted to try WM6.1 (0.4.9.0 digital) also. The following happened:
Everything worked fine, but at 54% flashing my brother lifted the phone, possibly it lost the USB-contact, because the flasing stopped with an error message (unfortunately can't remember the error number). Since then if I try to flash it with WM6.1 or WM6.5, after 1% the phone resets itself, and the RUU gives a 270 error.
I have the original WM5 ROM also, but if I try installing it, after "Verifying information on your PDA Phone" screen I get a connection error 260.
What can I do???
After the phone resets itself, I can see the HTC logo, and the red letters and numbers, but that's all.
If I try HardSPL, I also get a 260 error.
Can you enter bootloader manualy?
If you can than see SERIAL change to USB when connected to PC it should be OK.
if you have a SD card, you can also try to flash "manualy".
- put your RUU... NBH at the root of the card,
- rename it trinimg.nbh,
- reinsert the card in the phone,
- enter in bootloader (power+cam+reset)
you will have a grey screen asking to push "power", do it and that's it.
if USB is well working, maybe you just need to reflash the hardspooler.
Thank you for your replies.
Fortunately I solved the problem.
I did the following:
1. To be sure, do all the stuff on a Windows XP machine
2. DISABLE "Allow USB Connection" in Active Sync so you see a small red X symbol next to the Active Sync symbol
3. Start the device into Bootloader mode (Cam+Power+Reset) and connect the device to your PC and make sure USB is written on the bottom of your screen (NOT Serial!)
4. Download splxploit (http://forum.xda-developers.com/atta...0&d=1180043588) and execute unlock on your PC
5. Follow the instructions
6. Download HardSPL (http://forum.xda-developers.com/atta...8&d=1185364317) and follow the instructions
7. Finally (to be sure) restart into Bootloader mode and check if SPL is showing "SPL-1.30.Olipro) - if this is the case you've done it !
8. Flash your preferred ROM via miniSD or USB connection
I m glad you solved this. Every day another new way of solving the flash problems.
Hi to All guys
i've got a trinity from my work and it has a custom rom.
I wanted to changed the rom so i download a wm 6.5 and erase the trinity with mtty. After that i try to install the rom with he RUUUupdate, but it get error 270.
Only in that moment i read on the bootloader and see that it haven't olipro or another HARDSPL installed.
So i looked for a solution and i try the unbrick with the splxploit. I did it and i get olipro on the bootloader, but i don't know how go on with install, if i use the exe i get 260 connection error.
Can you help me?
Hi All,
from one moment to another my X1 decided to boot into bootloader mode.
The strange thing is however, that when I connect it to the USB of my PC and reset the X1, it boots normally. Well, almost normal as the USB doesn't seem to be working.
I flashed the rom to APP-SW_X1_GENERIC_UK_1213-6450_R3AA010__KOVS using the SDCard and that worked without a problem. But still the X1 boots into bootloader mode (except when connected to the PC).
I tried a hardreset, pressed the volume down button several times (to make sure it isn't stuck), tried to use MTTY (but that doesn't show a prompt), but nothing seems to help.
Is there anyone who can help me with this, because I'm out of ideas....
Update:
I managed to boot the OS (USB connected) and install HSPL using Xperia-SSPL-Manual. This succeeded and I now have SPL-0.78.OliNext. I flashed the phone to a new ROM (826x_KOVSKY_29017_2021), and that succeeded as well. It didn't solve my problem however. I still get the bootloader screen when I start the phone and can only start the OS by starting with USB connected...
Update2:
Yesterday evening I took the whole phone apart to make sure no buttons are/were stuck. Didn't find anything, put it back together and it still boots into bootloader.
I also managed to get a connection to the phone using NueTTY. I executed command Set 14 0, restarted the phone...and still it boots into bootloader.
If there is any one who knows of something that I haven't tried yet, PLEASE let me know....
same problem,,if there's a way to flash recovery from sd card in fastboot mode,,that'd be great
kldahmd said:
same problem,,if there's a way to flash recovery from sd card in fastboot mode,,that'd be great
Click to expand...
Click to collapse
Flashing the ROM is no problem, I can put every ROM on it that I like. But even after flashing the ROM the phone still starts in bootloader....
You can try to go into the bootloader on ur pc and use recovery.bat with fastboot.
xvink said:
Flashing the ROM is no problem, I can put every ROM on it that I like. But even after flashing the ROM the phone still starts in bootloader....
Click to expand...
Click to collapse
hi, I'm kind of having the same issue as you do..can you please be of help and tell me how did you manage to HSPL it to 0.78.OliNex?
Correct me If I am wrong, but you must copy Xpera_SSPL_Manual. exe on X1, run it from file explorer and then run X1_HardSPL.exe on your PC, whlie X1 is connected via usb (although mine also doesn't recognize the X1) ?
i would really apreciate it... thnx
i have the same problem guys, did anyone of you found any solution for this?
same problem
Have you tried to do a task29 with KovskyAdvancedRUU?