Related
Hi everyone,
I got my new Kaiser (AT&T Tilt) last week, unlocked of course, and I have reformatted it yesterday, and since then, I am unable to get Wifi to connect to any network! The device shows me the available network and everything, but it says it's connecting to them and then it just says they're available
Any solutions? Suggestions?
-W.
TyTN X said:
Hi everyone,
I got my new Kaiser (AT&T Tilt) last week, unlocked of course, and I have reformatted it yesterday, and since then, I am unable to get Wifi to connect to any network! The device shows me the available network and everything, but it says it's connecting to them and then it just says they're available
Any solutions? Suggestions?
-W.
Click to expand...
Click to collapse
same here.... but no solutions yet....
What ROMS/Radios are you using?
Actually, a solution that would work is to power cycle the device (remove the battery for a few mins out of the device, put it back in, and run again) however, I am not sure about this solution as it may be a temporary one!
The ROM I have is:
1.57.502.2
Radio:
1.27.12.11
Any suggestions on the ROM/Radio?
-W.
just a suggestion of what works for me.......my POS router, i can only connect to it if the wifi power mode on the kaiser is set to best performance. same sh*t with the wizard and the hermes. i seriously should get a new router
i had the same issue. But today i triedd q-mobile rom, which has a different radio than before. It works now. I am finally connected to my router. I have a Tilt as well.
I've noticed variations in performance and willingness to connect to APs depending on the Radio version. On 1.27.12.32 it would sometimes connect, other times not - and take a long time! On 12.17 it connects pretty quickly to most APs. If it doesn't, I turn Wifi off, then on.
Actually, It used to connect to the same network (probably different AP) with no problems at all!
I encountered the same issue today, and even after a powercycle the same thing happened..
BiPolarXpress said:
i had the same issue. But today i triedd q-mobile rom, which has a different radio than before. It works now. I am finally connected to my router. I have a Tilt as well.
Click to expand...
Click to collapse
I had the same problems you guys had. tried to connect then would say available.
i took your advice. first i tried to install the radio that comes with the q-mobile. i couldnt install it to my phone, the screen would black out.
next i went ahead and installed the latest version of q mobile. now it works. and btw q mobile is one fast freaking rom! the screen goes from landscape to portrait in a flash!
thanks!
Mine abruptly started not connecting to any network as well. I'll try the powercycle idea. I have the AT&T standard ROM.
ranger47 said:
Mine abruptly started not connecting to any network as well. I'll try the powercycle idea. I have the AT&T standard ROM.
Click to expand...
Click to collapse
So if I powercycle it it works, except that when I try and connect to what wifi it works for a minute or so and then causes the same problems.
ok, need help with my wifi also, if I go to Wireless Lan settings it says LAN is off, and has a link to click to turn it on, I click it and it connects, shows info including signal strenth, then it disconnects.........it wont stay connected
jsnone1 said:
ok, need help with my wifi also, if I go to Wireless Lan settings it says LAN is off, and has a link to click to turn it on, I click it and it connects, shows info including signal strenth, then it disconnects.........it wont stay connected
Click to expand...
Click to collapse
I am facing the same problem. anyone help?
Hmm, sounds like the same problem I was having. See http://forum.xda-developers.com/showthread.php?t=366526
Not really a fix but a better workaround than having to reboot all of the time.
Wifi Problems with TyTn II
I have a HTC TyTn II and i have some problems with "wlan".
I cannot connect with my router.
I tried it even withouth a security key but it says connecting and for the rest nothing happens.
Ive resetted my router to default settings so everything is open but still i cannot connect my phone to the router.
My router brand is:SMCWBR14S-N2.
Details of my Phone:
Rom version: 1.56.404.6
Rom date: 08/28/07
Radio Version: 1.27.12.32
I hope you guys can help me, Thnx
Hi,SMCWBR14S n2 router the same problem for me but when i turn it to 802.b it works.
I think there is something in the mixed mode what the pda dont respect.
I have a similar problem, but with a twist.
When I'm at my parents, I can connect to their BT Homehub Wifi with no problems at all, even on power-saving wifi mode.
At my house, I have a Siemens Wifi router (from Tiascali), and I cannot connect to this (says it is available, shows signal strength, but won't successfully connect) unless I turn off the encryption/security key.
The only difference between the two networks (apart from the names) is the BTHomehub uses 64bit WEP key and the Siemens uses WPA-PSK key (AES/TKIP not specified in router setup page). I can change the key method on the Siemens to 64bit WEP, but it still won't connect. My laptop connects without problems to both networks.
Is this a problem with encryption handling by the Kaiser?
ROM: Dutty's WM6.1 WWE 29/04/08
Radio: 1.65.14.06 (tried the other radio version of Dutty's rom with same results)
Chris
edit: verfarkas, that's something I haven't trued yet - I'll give it a go when I get home tonight. That would be a nice simple fix - by default, my Siemens router has the "b" (and other suffixes) chosen automatically.
Change to best performance
I was having all of the above problems until I set my power save mode to "Best Performance". Go to settings -> Connections -> Wireless LAN
hey guys, i'm using one of dutty's 6.0 roms, and when i first started using it, i opened the comm manager and turned off the 3G. once i did that the comm manager doesnt even have that 3G icon anymore. now i'm using a friends sim card to tether, and i cant seem to get 3G on. its pretty crappy tethering w/edge, so if somebody can help me i'd appreciate it, thanks
omar
Haven't got my phone in front of me, but if you go into Start > Settings > Phone, there's an option in there for Network connection which can either be set to Auto or GSM/GPRS . This is all the 3G button in the Comm Manager does (Auto is 3G on, GSM is 3G off).
Sorry if the directions are a little vague, I'm doing this from memory and it's been a while since I had a Comm Manager without the 3G button!
Of course, if your friend's SIM or account isn't 3G-enabled, then whatever you do to your phone won't work!!
So I connect to internet on PC via Kaisers USB which connects to HSDPa.
Problem is that HSDPa connection disconnects aprox. every 8-10mins.
I dont know why, on my Wizard everything works fine.
Where is the problem?
Thanks.
BUMP
So, im using kaisers internet connection on mine PC (internet sharing,usb) and every 10minutes connection drops.
Where is the problem?
Thanks.
Please provide some additional information. Such as: Carrier, ROM version, and Radio version.
I frequently tether for several hours at a time and do not have an issue with disconnects, so there is probably a settings issue that will not come to life until we know a little more about your situation.
NotATreoFan said:
Please provide some additional information. Such as: Carrier, ROM version, and Radio version.
I frequently tether for several hours at a time and do not have an issue with disconnects, so there is probably a settings issue that will not come to life until we know a little more about your situation.
Click to expand...
Click to collapse
Carrier name is "VIP" , location: Europe(Croatia)
ROM: WM 6.1(nothrills)
r 1.65.14.06
g 25.81.40.02H
d 3.14.00.00
I had the same network setup on HTC Wizard and everything worked just fine...
Have you tried any other ROMs or radios? I was able to tether using the NoThrills ROM back when I was running it.
You can also try reflashing the same ROM and radio again in order to eliminate any possible problems stemming from a "bad flash".
Do you have the kaiser tweak installed?
No i didnt try any other ROM or radio..
Everything works fine on that ROM and radio ,only internet sharing is a problem..
And yes i have installed KaiserTweak.
Do you have it set to disconnect your internet?
No i didnt set to automatic dissconnection...
Maybe try another tilt or reset the phone????
huh...i've finally setup everything on this ROM and everything works very nice...so i dont want to flash another ROM (of course if this is only solution, i will..)
strange how nobody had this problem..
NoThrills is a WM6.1 ROM, and your phone would have shipped with a 6.0 based ROM since 6.1 isn't out yet. Did you have this problem prior to flashing to NoThrills?
Well i didnt try on 6.0 original rom...
I've flashed it same day i've got it..
Think i will flash some other ROM..
Any suggestions?
Thanks.
When you say that HSDPA disconnects are you sure it's disconnecting or just downgrading to idle. On my Kaiser I see that when the connection needs to pull data from the net, the icon changes to H (HSDPA) and when idle it changes to just 3G but remains connected. I can see that it remains connected because the signal icon has the 3G logo on top of it.
Cheers!
Rayan
I noticed too that when connection is idle stands 3G icon and when downloading there is H.
But yes, it just disconnects..
When I'm using connection on Kaiser(not internet sharing), it doesn't disconnects..
Hey guys I need a little help I just got a new diamond and it is working great. So far I am in the process of HardSPL and then will install radio .05 however my question is that it will connect to at&t fine with phone service but when I try to open internet or download weather data it says there was a connection error. Can anyone tell me how to set up this internet I will do HardSPL tonight and put on the new radio and see if that does anything. Thanks
I had trouble with data on the .03 radio as well, but have had no troubles at all with the .05 radio. Also, go to Settings/Phone and set Network type to GSM, and Band to 850+1900. That seems to help with battery life (since the Auto settings cause it to constantly search for the best option), and it might have also had something to do with getting data to work, but I'm not sure because I updated my radio to 05 at the same time.
Hey thanks that seemed to work as now I have data access I did think it would make much difference switching radios but it does thanks a bunch.
hey one more question have you figured out how to use weather in the USA as the internet works but when I hit update weather it shows in the status bar updating then comes up with an error message saying "connection error" any idea?
A strange problem..
I recently got GPRS activated on my sim..
When i try connecting on my Diamond, the E becomes active and it tries to connect.. But after abt 30 secs to a min, it says "Cannot connect for an unknown reason... etc etc.."
I initially thought it was a problem with the network..
But, when i put the same sim in my old Asus P525, set up the connection and tried to connect, the G became active and got connected within a few seconds!!!
From then i've been tryin to connect on my Diamond and have got connected about twice with E in the signal bar.. But that must've been some freak accident cos after a few hours i tried connecting w/o changing any of the settings and absolutely no luck!
I've tried almost all the cooked ROM's. And different radios.
Right now i'm on the Official WWE ROM 1.93.
Hard SPL 1.23 or 1.24.
And 1.00.25.03 Radio.
Any idea about what's wrong, guys?
Make sure you have the correct GPRS/WAP settings installed on your HTC Diamond.
There are different settings for Payandgo and Contract SIM cards.
You can try searching Google for them, or if you live in the UK try this website: http://www.filesaveas.com/gprs.html
prank1 said:
Make sure you have the correct GPRS/WAP settings installed on your HTC Diamond.
There are different settings for Payandgo and Contract SIM cards.
You can try searching Google for them, or if you live in the UK try this website: http://www.filesaveas.com/gprs.html
Click to expand...
Click to collapse
prank1, the settings are right..
That's why it's working on my old phone..
I think it may have somethin to do with Edge and GPRS..
Maybe my service provider does not have Edge capabilities..
If i'm able to restrict my Diamond to try and connect to Edge and connect to GPRS instead, it may work..
Any way that could be done?
sanctifiedrust said:
A strange problem..
I recently got GPRS activated on my sim..
When i try connecting on my Diamond, the E becomes active and it tries to connect.. But after abt 30 secs to a min, it says "Cannot connect for an unknown reason... etc etc.."
I initially thought it was a problem with the network..
But, when i put the same sim in my old Asus P525, set up the connection and tried to connect, the G became active and got connected within a few seconds!!!
From then i've been tryin to connect on my Diamond and have got connected about twice with E in the signal bar.. But that must've been some freak accident cos after a few hours i tried connecting w/o changing any of the settings and absolutely no luck!
I've tried almost all the cooked ROM's. And different radios.
Right now i'm on the Official WWE ROM 1.93.
Hard SPL 1.23 or 1.24.
And 1.00.25.03 Radio.
Any idea about what's wrong, guys?
Click to expand...
Click to collapse
My bad - didnt see the 'set up connection' bit so I assumed you didnt have the correct settings.
I had this problem once but it went away with a ROM upgrade - that was when I had the XDA Orbit.
The problem may be that my phone does not try connecting to GPRS and directly tries to connect Edge..
Isn't the connection supposed to be G-E-3G, in that order?
Is there any way i can prevent my phone tryin to connect to Edge?
Can i make GPRS as first preference instead?
Anybody? Please?
From what i heard my diamond doesn't support US( or Canada which is where i live) 3g because of diamonds hardware so that's why it only connects to edge which is really slow... anyways to connect i had to phone rogers my wireless provider and they gave me my username and password which was needed to connect online. So i'm guessing it's the same for you if you go to
Settings > Connections > rogers internet( for mine) > Manage existing connection
from there you'll go to the next page where you can input your info.
NekciuQ said:
From what i heard my diamond doesn't support US( or Canada which is where i live) 3g because of diamonds hardware so that's why it only connects to edge which is really slow... anyways to connect i had to phone rogers my wireless provider and they gave me my username and password which was needed to connect online. So i'm guessing it's the same for you if you go to
Settings > Connections > rogers internet( for mine) > Manage existing connection
from there you'll go to the next page where you can input your info.
Click to expand...
Click to collapse
Hey.. That doesn't seem to be the prob since i can get it to work on my old PDA with the same settings..
That phone gets connected and it shows 'G'.
What might help me is somethin to block my phone tryin to connect to Edge before it even tries to connect to GPRS..
I don't think that's practical, but wishful thinking..
I've had the same issue with my Diamond, I know for sure that the network settings are correct as it sometime connects fine and other times I keep getting the "Cannot connect for an unknown reason..." error- only a soft reset would resolve the issue. Seems a bit random but am trying to monitor what is causing it.
It always used to work fine on my Hermes. BTW I'm using Dutty's ROM on my Diamond.
sh500 said:
I've had the same issue with my Diamond, I know for sure that the network settings are correct as it sometime connects fine and other times I keep getting the "Cannot connect for an unknown reason..." error- only a soft reset would resolve the issue. Seems a bit random but am trying to monitor what is causing it.
It always used to work fine on my Hermes. BTW I'm using Dutty's ROM on my Diamond.
Click to expand...
Click to collapse
Yeah.. Sounds almost like my prob..
Could it be a rare manufacturing defect sort of thing thats affecting our phones?
Cos nobody else seems to have such an issue..
And i keep changing between Dutty's and Panosha's ROM..
I don't know if it's same problem you have ,
but I had kinda same problem..
I found that the lame ActiveSync change the proxy of my internet connection and put in the internet connection proxy my local proxy at work, even I removed the proxy it didn't help (dunno why) , just by adding new connection from the advance and adding new name etc.. it solve the problem...
sanctifiedrust said:
And i keep changing between Dutty's and Panosha's ROM..
Click to expand...
Click to collapse
I've only had my Diamond (MDA Compact IV) for only about 3-4 weeks. I was so keen to flash to a different ROM that I did so within 10-15 hours of receiving the device; my point being that I didn't get to try out my data connection on the stock T-Mobile ROM.
The connection seems to be fine today...!
arix said:
I don't know if it's same problem you have ,
but I had kinda same problem..
I found that the lame ActiveSync change the proxy of my internet connection and put in the internet connection proxy my local proxy at work, even I removed the proxy it didn't help (dunno why) , just by adding new connection from the advance and adding new name etc.. it solve the problem...
Click to expand...
Click to collapse
Hmmm.. I don't think i have the exact same problem, but somethin similar..
I'll try adding a new connection..
Thanx..
As I know something with Activesync **** the GPRS connection..
Let us know if you solve your problem with new connection...
Ok.. Note the "E" in the first pic and in the second..
The first one is 'clear' and the second one is 'hazy'!
When the "E" is 'clear', my GPRS connects!!!
I found this out after putting a different sim card of a different network and connecting..
When i put the other sim card, i got 'clear' "E" and GPRS worked..
Then i put back my old sim card and on switching on the phone, the "E" was still 'clear'!!
On tryin to connect, it worked!!!! Even after several manual diconnections, it worked only cos the "E" was still 'clear'..
Then i reset my phone with my sim card and got the 'hazy' "E".. And back to square one.. Not connecting..
My question is, what does this 'hazy' "E" mean and how do i make it 'clear'???! Only then my GPRS seem to work!
Help!!!!!!
This is how it is when connected properly..
Cannot connect for an unknown reason
I also had this problem. To make my story short, I have a data plan with Claro Peru which I have been using with my Touch (not 3G phone) with no problems. 3 days ago I acquired my Diamond 3G US version. When attempted to connect to the HSDPA I got the error mentioned here (cannot connect for..., sometimes the "H" symbol was difusse [like in the picture in a previous post in this thread], etc). The root cause of this was that my data plan only have GPRS/EDGE activated, my network provider (Claro) differentiates 2G internet vs 3G (so no HSDPA/UMTS until subscribing to a new plan).
The **SOLUTION** for my case was to select under "Select your network type" the option GSM (Start, Settings, Phone, Band tap). The option Auto was the default. Thus restricting to EDGE my data connection (which is according to my plan). Also, on the same tap I selected UMTS(850+1900)+GSM(850+1900) under "Select you GSM/UMTS band". You have to select here the frequencies according to your country.
P.S. The problem was the same before and after I updagred my ROM to RUU_Diamond_HTC_WWE_2.03.405.3_Radio_Signed_Diamond_52.51.25.26_1.09.25.23_Ship. So, two things to mention here. 1, A ROM upgrade is not the solution for this problem (in my case). 2, you can upgrade the Diamond US version (my is DIAM110) with a WWE ROM upgrade.
Hope this help someone.
dach said:
I also had this problem. To make my story short, I have a data plan with Claro Peru which I have been using with my Touch (not 3G phone) with no problems. 3 days ago I acquired my Diamond 3G US version. When attempted to connect to the HSDPA I got the error mentioned here (cannot connect for..., sometimes the "H" symbol was difusse [like in the picture in a previous post in this thread], etc). The root cause of this was that my data plan only have GPRS/EDGE activated, my network provider (Claro) differentiates 2G internet vs 3G (so no HSDPA/UMTS until subscribing to a new plan).
The **SOLUTION** for my case was to select under "Select your network type" the option GSM (Start, Settings, Phone, Band tap). The option Auto was the default. Thus restricting to EDGE my data connection (which is according to my plan). Also, on the same tap I selected UMTS(850+1900)+GSM(850+1900) under "Select you GSM/UMTS band". You have to select here the frequencies according to your country.
P.S. The problem was the same before and after I updagred my ROM to RUU_Diamond_HTC_WWE_2.03.405.3_Radio_Signed_Diamond_52.51.25.26_1.09.25.23_Ship. So, two things to mention here. 1, A ROM upgrade is not the solution for this problem (in my case). 2, you can upgrade the Diamond US version (my is DIAM110) with a WWE ROM upgrade.
Hope this help someone.
Click to expand...
Click to collapse
I have the Diamond on T-Mobile in the UK with the web'n'walk plan (HSDPA enabled - although not the higher-speed "plus" version). This happens to me every single time I'm in a GPRS-only area - when I have HSDPA coverage, it connects fine. In order to get it to connect, I have to open the Comm Manager, turn off the data connection and re-activate it.
Before anyone asks, my connection settings are all correct and I've tried numerous different main and radio ROMs - nothing makes a difference. I'll give this a shot, see if it makes a difference.
BLCollier said:
I have the Diamond on T-Mobile in the UK with the web'n'walk plan (HSDPA enabled - although not the higher-speed "plus" version). This happens to me every single time I'm in a GPRS-only area - when I have HSDPA coverage, it connects fine. In order to get it to connect, I have to open the Comm Manager, turn off the data connection and re-activate it.
Before anyone asks, my connection settings are all correct and I've tried numerous different main and radio ROMs - nothing makes a difference. I'll give this a shot, see if it makes a difference.
Click to expand...
Click to collapse
OK, I would try the option Auto for the "Select your network type" so the phone auto negotiates the technology in use (between GPRS or the much better HSDPA), but change the option for the bands according to your country.
Let us know the results!