yesterday my tytn2 started to act crazy, i didn't drop it or installed any new software.
the screen started to turn on on his own, front buttons stopped working accept the center button witch now opens the start menu.
when i open the keyboard the fn light is on and the keyboard doesn't work.
when i write the sms message trough touchscreen the backspace isn't working so i can't delete misspelled words.
the photo button and power button on left side still working fine.
all the applications work fine, and i can make calls trough touch screen.
i can't make hard reset because front buttons wont respond.
is anybody had similar problems or have the solution.
my guarantee is gone so i hope this is software problem.
Try doing a battery pull and letting your phone sit like that for a minute, put the battery back in, and see what happens...
It sounds like you have water damage to your phone, though. Every take it in the bathroom with you while you shower? The steam in the air is a sure fire way to get water damage, and it will take time to show, but eventually circuits rust and stop working and you end up with a lot of random problems, and usually all of a sudden you have a lot of major problems.
well, i can't remmeber that i had carry it in the bathroom while showering.
i pulled out the battery, waited for about 5 mins and when i put it back nothing has changed. thanks for the tip.
is there a way to do a hard reset without pushing the front buttons?
konch said:
well, i can't remmeber that i had carry it in the bathroom while showering.
i pulled out the battery, waited for about 5 mins and when i put it back nothing has changed. thanks for the tip.
is there a way to do a hard reset without pushing the front buttons?
Click to expand...
Click to collapse
look in the wiki for a detail of all the ways you can perform a hard reset (i believe there are at least THREE ways)
METHOD 1: the one you are looking for (because your buttons don't work) can be triggered by going to Settings->System->Clear Storage (assuming your phone still boots up and the touchscreen is usable)
METHOD 2: when the phone is POWERED OFF:
1. stick the stylus in the soft reset hole and hold it there
2. hold down the two soft keys
3. press the power button
if you try METHOD 2 and if it works, then you can safely assume that your soft keys are working and that it is indeed a software issue.
i used METHOD 1 and did a hard reset.
nothing has changed, front buttons and keyboard still refuses to work.
unfortunatly it seems it is a hardwer problem so i'm going to take it to the service.
thank you for helping me.
Related
I have tried several times to hard reset using proceedure described, but the phone just restarts.
Help!
http://forum.xda-developers.com/showpost.php?p=2480910&postcount=4
Cannot hard reset as shown.
The phone does not show reset message & justs restarts, like a soft reset.
it happened to me also. i thought i can not hardreset but the problem was i was doing it wrong.
my recommendation to you:
try and do it without the back cover. to push the reset you need to enter yr stylus in an angle. that together with the use of the other hand (two fingers) make it hard to hard reset (pun intended). i found that i can do it much easier without the back cover or (also highly recommended for ppl with small hands) ask somebody to help you (three hands method ).
make sure you are pressing the volume down button.
also: keep pressing all three points for 1 sec then first release the reset button and keep the other two pressed for 1 second more before releasing and for god's sake do it over and close to a soft surface..., just in case.
i gave up. my phone is about to snap in half from me holding it down so hard. my hands are ****ing numb. what i think i'm doing is i move either slightly up or down while holding down the enter key and it becomes up or down instead of enter.
i did the settings-clear memory-1234 method but is that really the same as a physical hard reset.
i think i did **** up the phone, the usb connector interferes a little as it goes in the phone and activesync doesn't work anymore.
Try this procedure as another method.
Soft reset and the immediately press the volume down + round center button. Then follow procedure in grey menu to reset device back to manufacture settings. This is the same as a Hard Reset.
Good Luck and try not snap things, especially your device, lol
today's my first day with the phone, i really don't think i should ever try a physical hard reset again if i don't want to break the phone. activesync still works, whew...
mgs333 said:
today's my first day with the phone, i really don't think i should ever try a physical hard reset again if i don't want to break the phone. activesync still works, whew...
Click to expand...
Click to collapse
A Hard Reset doesn't brick the phone....
band27 said:
A Hard Reset doesn't brick the phone....
Click to expand...
Click to collapse
i wasn't talking about bricking the phone, but literally snapping the phone in half or something similar from pushing or bending the phone too hard.
anyway, i had a breakthrough today. previously, i was so intent on keeping the buttons pressed (especially the enter button) that i was pushing incredibly hard on the phone, making me feel like i was bending it too much.
and what was happening was that pushing it hard doesn't really help but rather hurt me because it was either being pushed as up or down (or even left or right) while pushing so hard.
the key for me was before pushing reset, to press it not crazy hard but press in directly straight and move up and down to make sure i'm not pushing up or down, and practice keeping it pressed in straight, then when i'm comfortable with that, (while keeping volume down pressed of course) then press the reset button.
and the grey hard reset screen should come up within a couple of seconds of resetting. so if it doesn't appear within a few seconds, let go of the poor phone and try again. previously, i had no idea how quickly that screen was to appear so i would hold it for 1-2 minutes while the phone was going through its booting process. hopefully this helps save some wear on your hands and fingers.
HTC BA WM 6.5 hard reset
Guys need your help also htc blue angel updated rom to windows mobile 6.5. I cant make a hard reset. wud like to know if there is a program for doin such. or any physical ways of having it done
Japsmate said:
Guys need your help also htc blue angel updated rom to windows mobile 6.5. I cant make a hard reset. wud like to know if there is a program for doin such. or any physical ways of having it done
Click to expand...
Click to collapse
http://forum.xda-developers.com/forumdisplay.php?f=244
This morning I woke up to find that my kaiser's buttons were non-responsive. after about 2 min of testing, I found that only two buttons on my kaiser worked, the power button, and the center button (it acts like the windows button now WTF???). Also, when I power on the device, I see the dialer pop up, and the following W on the far right, wich is replaced with S, then Z, then X. (can you say WTF???) The touch screen works perfectly, and none of the keys on the keyboard work.
I would love suggestions on what to do to fix it (I am not afraid to take it apart, I just need a torx-5 bit), and barring that, suggestions on a new phone.
See here: http://www.youtube.com/watch?v=oMv3VONt0R4
Fenny said:
This morning I woke up to find that my kaiser's buttons were non-responsive. after about 2 min of testing, I found that only two buttons on my kaiser worked, the power button, and the center button (it acts like the windows button now WTF???). Also, when I power on the device, I see the dialer pop up, and the following W on the far right, wich is replaced with S, then Z, then X. (can you say WTF???) The touch screen works perfectly, and none of the keys on the keyboard work.
I would love suggestions on what to do to fix it (I am not afraid to take it apart, I just need a torx-5 bit), and barring that, suggestions on a new phone.
See here: http://www.youtube.com/watch?v=oMv3VONt0R4
Click to expand...
Click to collapse
Try hard reset first.
solution..!
hi
first try soft reset, and if that doesnt work then uninstall some program and after each uninstall soft reset
if this doesnt do it for the device then there only one option---->HARD RESET
regards
Hi,
maybe it's a an issue using a creen locker like Sunscape, ThrottleLock or S2U2. Try uninstalling them (it), could help.
Well, I soft reset it a couple of times, same result, I can't hard reset it, because the button combination does not work, and neither does clearstorage. it looks like it's a hardware problem to me.
Hi, I cleaned the screen of my HTC Diamond with a bit of alcohol and a pice of tissue and it seems that the alcohol got inside of the Power button. Now, every time I try to turn the screen on by touching the power button, it turns the screen on but it dispays a message that says: "Warning: Power will be turned off and you may lose data if you have not saved them. Do you want to continue?"
If I click YES, it reboots the phone, If I click NO, then its ok. That is fine, but the problem is when I want to turn the phone off. It's impossible. It will keep trying to reboot.
Does anybody know what can I do? I am really worried.
One solution could be to make some other button from the phone to act as the power button (like the Home button that is rarely used). How can I do that?
Please help!!!!
Thank you
Hi,
I have the same problem.
Did you already find an answer ?
No, I didnt find the solution. I tried to fix the hardware but didnt succeed. So, I created a dummy file to emulate the poweroffwarning.exe that pops up when you long press the power button.
Solution
Hello, I have one AT&T TITL 8925 that upgraded to Windows Mobile 6.5
After the new software was loaded I saw same behavior on my phone.
When the phone is ON and I pressed the power button sometimes it do not respond, and others I received the warning message "power will be turned off and you may lose data if you have not saved them..." My first tought was that it is because the processor is slow to this new software release, or maybe my phone is damaged. I was working perfectly with previous (light version) release so my final guess is that this sw requires more uses of the processos.
Anyways what I have been doing is before turing it off I press the red button or hang up button, and after this if I press the power button it works fine (No more warnings). I have some theories but I will keep doing the same
Hope this partial solution helps you as it does for me.
Regards
Jerry
this is not working for me :| the problem is i can't use my power button not even to open my display when it goes to sleep :|:| i don't know what to do guys please help me
You can use the Stylus to awake the phone, instead of using the power button. You can also use TouchLockPro, to suspend the device, so you do not need the power button for that too.
Also you can set the phone to awake on pressing any key (Windows Mobile Setting), but be sure to have a good locking tool, which makes sure you do not have bogus calls and it goes to sleep again fast enough, otherwise it will drain battery.
I have the same problem.
Anyone solved this one?
I have the same issue and this is not a hardware problem. Strange since even updates/changes of the rom do not correct the issue. Did anybody find a solution for this...?
Well.. ive had this problem just ones.. I was walking downtown with my diamond in the frontpocket of my jeans (face down), after about 3min. of walk, it started to rain (big drops), and my clothes got completely wet, i turned around emidietly, to walk back to home. When i got home after 3 more min. i layed the phone on the table, and then i could hear there were somethibg wrong.. The "turn off" sound came, and the notification kept on coming up, even though i pressed No, as if i were just holding the power button down.. Then i began to press the power button continuesly for about a 100 times, and to my surprise then it stopped and have functioned perfectly for about 2 month now.. Something tells me theres some serius promlem with the smallest kind of moisture near the power button on this phone..
Yes this is hardware related.
If you take a look at the inside of the powerbutton, there are 2 points making contact when you press the button.
If you press it, the software will recognize this and the screen will turn off.
If you press it long enough you'll get the "Do you want to turn off your device" message.
But, if water gets underneath the button, the 2 points may be making contact, because water/alcohol conducts.
In this way you'll get that message.
The button is very weak. Due to this, it may not properly work if you have used it for a long time.
I think that could also be a reason why you constantly get that message.
[ElCondor] said:
Yes this is hardware related.
If you take a look at the inside of the powerbutton, there are 2 points making contact when you press the button.
If you press it, the software will recognize this and the screen will turn off.
If you press it long enough you'll get the "Do you want to turn off your device" message.
But, if water gets underneath the button, the 2 points may be making contact, because water/alcohol conducts.
In this way you'll get that message.
The button is very weak. Due to this, it may not properly work if you have used it for a long time.
I think that could also be a reason why you constantly get that message.
Click to expand...
Click to collapse
Hi! on one of my diamond, the power button off from the board. So the black little board with the button itself is not part of the complete circuit anymore... if someone know the hw testpoint for that it would great please.... i see a few TP around, but if i just start sorting them i just going to kill it...I use to flash phones with TP so is not new for me , but i find nothing for diamond.
I have a similar issue. Mine seems like it is almost stuck on, so it wakes its self up all the time, meaning a full charge lasts an hour or two. Then when it runs out of battery it tries to switch itself back on, so goes through a continuous cycle of vibrating and beeping until the battery is removed. The gf finds it very annoying at 3am lol.
Don't recall mine getting wet, but it's possible it could have got damp at some point, but it's been doing this now for about 3 weeks.
Tried a hard reset with no luck.
[ElCondor] said:
Yes this is hardware related.
If you take a look at the inside of the powerbutton, there are 2 points making contact when you press the button.
If you press it, the software will recognize this and the screen will turn off.
If you press it long enough you'll get the "Do you want to turn off your device" message.
But, if water gets underneath the button, the 2 points may be making contact, because water/alcohol conducts.
In this way you'll get that message.
The button is very weak. Due to this, it may not properly work if you have used it for a long time.
I think that could also be a reason why you constantly get that message.
Click to expand...
Click to collapse
I can see that how to remove the power button from the video showing how to replace the screen. Any idea if once removed the button can be fixed, if not can you get replacements?
2004mark said:
I can see that how to remove the power button from the video showing how to replace the screen. Any idea if once removed the button can be fixed, if not can you get replacements?
Click to expand...
Click to collapse
I think I should send it to HTC, and ask them to do it. Or go to a repair centre. But I should not try it myself, because it can be dangerous for the diamond.
Also try searching on ebay, there might be the parts you could use.
Good luck!
is there a way to remap the power button?
my diamond face same problem since this afternoon, arrrrgghhhh!!!
- blocking hwbutton1, hwbutton2, hwbutton3, hwbutton4, hwbutton5, hwbutton6, hwbutton7 >>>> NO LUCK
- hard reset >>> NO LUCK
guys, any of you solved the problem yet
youtube.com/watch?v=Q4SEQ6AUFOI
My Sony X1 have some strange problems with the power button. When it goes into sleep mode, I can not wake it up with the power button, all I can do is to soft reset. Sometimes it does not go into sleep mode either , it just "wake up" all the time. I don't know what's wrong with it, tried Hard reset but no use .
ANyone had this problems before?
@
The only way to solve this is to leave the phone near your laptop heat vent ( fan) . hot air from it might help you to get the power button up and running. But if that to doesn't work then i'm afraid thats bad.
Current sol :
1. download SU2U ( search threads )
2. go to the settings and make the " lock when stylus inserted" option ON
3. Change the screen turn off time to 5 secs..
So , to unlock , remove stylus , to lock -> insert it back ( its turns off the back light within 5 sec )
Less annoying
elektros said:
youtube.com/watch?v=Q4SEQ6AUFOI
Click to expand...
Click to collapse
thanks for this link, i accidentally tear off my power button flex. now i could turn it on again. Thanks elektros
VERY long time no see folks!
It's been a little over a year if I remember correctly...
Anywho... I'm trying to revive an Xperia which had a very hard life. Ending with being ran over by my 2 and a half ton truck.
Yea.... it still works Now the phone I've been using since I ran over though... this pos couldn't survive the simple process of charging. The charging port has successfully broken off of the phone and will no longer accept a charge.
However, the screen on the Xperia is completely and totally screwed and I can't see anything. Ordering a screen isn't much of an option, reason one being I'd have to be without a phone until Thursday; and reason 2 being my Xperia has an issue realizing whether or not a SIM card is inside of it and isn't really usable as a mobile phone (but it works well as a stationary phone sitting in my house).
Now... I already have a program which willl let me actually see what the screen says, but it needs ActiveSync in order to work. Which... I can't install on the phone because it needs to be hard reset.
However, I can't remember the exact button presses to get it to hard reset, nor do I recall what comes after in order to get everything back running so that I can get to the phone's start screen.
Does anyone have pictures or a video of the full Xperia startup and hard reset processes? I tried scouring the internet but I couldn't find any.
well shut down the phone, remove battery for 5 sec,insert battery. hold the two soft keys (the ones under the screen) pressed with the mobile off and then holding on those two press the power button until the phone vibrates. when it vibrates release the power button bet keep pressing the other two. wait 10 sec with those 2 pressed then press r on your hardw keyboard wait 5 secs and press space on you hardw keyboard.
Hope it helped and i made any sense.
Hello, I have my moto G 2014 for about 2 weeks now (full stock, never even connected it to the PC). A few days ago sometimes when I lock my phone by pressing the power button the touchscreen becomes unresponsive. The side buttons both work but nothing happens as I tap the screen, I can't unlock it or shut down. Then, out of nowhere it starts to work briefly, and I can shutdown only, not unlock.
But this time it rebooted and remained unresponsive, I can input 2 of the pin numbers and then it goes unresponsive... RMA?
Thank you
This dont look like a problem before..... You seem to be the first one with this problem. Have you ever dropped your phone? Or installed something wierd? Can you also tell what you did before when this problem came?
The phone is imaculated, never droped it. The first signs were after I installed Swiftkey, the key to change between numbers and symbols was not responding. Now sometimes the screen is all unresponsive, other times the top bar can be accessed, other times the menu keys don't work. I did a factory reset, after much struggle to get to the Config. menu, rebooted to the same issue.
Mebseven said:
I did a factory reset, after much struggle to get to the Config. menu, rebooted to the same issue.
Click to expand...
Click to collapse
I wouldn't loose to much time, trying to hunt down the problem. Sounds like the digitizer is broken. Unless you use your phone only while connected to the charger. Most chargers will emit a low electrical field that makes it almost impossible to operate the touchscreen. If this is not the case, replace the device.
It's not connected to anything right now, the top bar and 3 menu buttons are working but the rest is dead, can't swipe the screen or select any app, not even the app drawer. I guess it's RMA time.
Yea seems like a good idea, its a great device. I hope your warranty is still working