I have a old HP Ipaq 1940 which I want to use for some testing n stuff, BUT--
I can tget it to work - turn it on, it shows HP loading screen(loading bar in bottom and 1.00 at right bottom), then it shows topbar on top of that screen and an error " 'BTTrayCE' is not a valid Pocket PC application." and ok in top right corner of that windows-- after a while it shows "print" screen and tap anywhere on bottom, tapped and back to bttrayce and topbar screen,,,, trying to press on ok (bttrayce screen) doesnt work but the screen responds(its like its not calibrated),, then by pressing all hardware buttons randomly i somehow get pass the "bttrayce" error- it goes to "tap the screen to setup your device" , taped it and it goes to allign screen ,, pressed all 5 times right in the middle of + and it shows the allign screen again <- can get past that screen!!!
the PPC had a cracked Digitizer (top of screen was OK, but at the same time bottom was about 1cm off the place you pressed) awhile back, but it had the same error ,, changed the digitizer(from ebay and installed it at home) and the problem still is there!!
tried HardResset and I can get in Parrot mode by pressing all 4 hardware buttons+ power button + reset button, but nothing works!!!
Related
Hi.
I try to start my X1, but when Align Screen appears, I'm taping "+" to corners and anything happens... Maybe I have to click some button too or something? Please help... (Xperia is brand new, with guarantee etc.)
First, try this:
- Turn off the phone.
- Hold the two buttons underneath the screen (Left and right)
- While holding, press and hold the power button.
- This should take you to a screen where you can reset your phone (factory defaults)
If after this procedure the problem still occurs, take your unit back to the store.
Try pressing harder
Make sure you use your stylus
When I got mine I spent a minute trying to allign it using my thumb! (first touchscreen phone)
Good luck
Instead of click keep the stilus preesed until the arrow moves to other position. It worked for me...(had the same problem)
xperia x1 align problem
Hi I'm new to this forum, so please forgive me if what I'm about to post is allowed, if not then I will delete it.
Ok my xperia x1 is in a loop on the alignment screen. I have managed to bypass it using remote align bypass, but the aligment is still screwed up. Does anyone havw the Xperia x1.dat so I can setup correctly please.
hi,
yesterday I disassembled my phone to fix a microp error that had occured when i had dropped my phone. i disconnected two cables (one for the keyboard, the other for the lcd screen). then i reconnected them both and then went about reassembling the phone. however I accidently ruined the power button of the phone when i was doing so. a little part of the power button came off (a black button with the black sticky tape).
when i connect my phone to a charger and the enter button shows a pulsing light indicating it is charging.
so i was wondering does anyone know how to fix the power button for the htc diamond, does it require any minor soldering? or is it possible to turn my phone on any other way so that i can assign a different key to act as the power button.
cheers.
You can turn the phone on by using the soft reset hole on the bottom with the stylus.
dwizzy130
did it fix the microp error? if so how?!
When i press the power button to turn the phone on, i get the Touch diamond logo after that i normaly get the rom information in red on the lower right corner. But now it turns black and it does nothing.
Can it be solved?
Hello there!
I have a weird problem with my Tytn2. When i try to turn it off by pressing for 5 seconds the power button, it displays on the screen the regular message, that power will be turned off and i may lose data if not saved. Press ok and the power seemes to be turned off completely, because the green led won't flash. But, when i press the power button trying to turn on the device, it doesn't boot for entering the system, it just suddenly display the Orange Logo and above it a tiny black bar with the proper icon showing me that i have no phone signal at all (see picture). By pressing the "x" in the right side of the bar, the logo dissapear and appears the home screen, but the same icon is showing that i have no signal at all. I have to go to the comm manager, press once the Phone symbol which is already blue (enabled), and it sticks on the Flight mode. Press once again the Phone, and i have phone signal. The fact is that the phone it doesn't turn off completely and it hangs in a weird state (sleep mode ?). Please help me if you can! Thank you very much !
Hard-Reset your phone.
The Mrs dropped the tablet and the touch function of the screen stopped working. No amount of cold boots helped so I decided to pop it open to see if I could see anything loose.
I could see that the cable towards the top left (by the power and volume buttons) was loose from the motherboard so I put everything back together.
Now the screen shows nothing... I can see the light come on but nothing is displayed