Database Develop

Is it bricked? (Upgrade ROM error)

(I'm not 100% sure this is the correct forum, but since it is very ROM related it didn't feel all wrong to put it in here...)
Hi guys. After som serious flashing of cooked ROMs I decided for some unknown reason that I should try to restore a stock ROM. Now, being very tired as I was, i completely forgott that its probably a good idea to flash a new Stock ROM on the unit BEFORE flashing it with a signed SPL....so I just flashed the Signed SPL to the device. That in it self seem to have gone ok, because when I start the unit it say "SPL-1.15.0000". Problem is though that it also says "Upgrade ROM error, please try again"
Now, what should I do? Have tried put both signed and unsigned SPLs on the storage card and started up via the volume down/pwr button thingy, but that does not seem to do anything. I have also tried to attach the unit to a USB port when in tricolor mode ("USB" shows up on the screen) and tried the CustomRUU program. It finds the device and starts to "upgrade" (grey screen on the device with 0%) but then it just doesnt seem to get any further...
As the device was working fine with a custom ROM before I started all this, I suspect that the main problem proably is that I now have a Standard SPL with a cooked ROM, and that they collide sort of. I, as well as the Blackstone, is now stuck and I am all out of ideas what to do? Have also tried Hard and Soft resets, but that doesnt seem to change anything.
Help!

try removing the SD Card and put the phone into bootloader mode and re-flash the stock ROM! if this doesn't work ... still with the SD Card removed try flashing to USPL and flash the stock ROM again!
hope this helps

You can try USPL on your HD and flash a custom or stock ROM with it.

PapaDocta said:
try removing the SD Card and put the phone into bootloader mode and re-flash the stock ROM! if this doesn't work ... still with the SD Card removed try flashing to USPL and flash the stock ROM again!
hope this helps
Click to expand...
Click to collapse
Thanks for the feedback!
Just be be sure, "into bootloader mode" is when you start the device holding down volume down and powerkey until you see the tricolor screen? Then that is probably what I have tried to do for a while now without success (total success that is, I do get into the tricolored screen)). Or maybe I am doing something wrong, could you perhaps point to a detailed explaination besides the one in "HardSPL" thread?
USPL I havnt tried, will do that! Is it still so that trying to do USPL on Vista is asking for trouble?
I read somewhere that Stock ROMs should only be flashed from internal storage, not SD cards, is that true? If so, how do I go about accessing that storage now when it doesnt show up in the file explorer on my PC (PC recognizes it as USB device, "HTC Sync" but I get no file access to it).

improwise said:
Thanks for the feedback!
Just be be sure, "into bootloader mode" is when you start the device holding down volume down and powerkey until you see the tricolor screen? Then that is probably what I have tried to do for a while now without success. Or maybe I am doing something wrong, could you perhaps point to a detailed explaination besides the one in "HardSPL" thread?
USPL I havnt tried, will do that! Is it still so that trying to do USPL on Vista is asking for trouble?
Click to expand...
Click to collapse
just do uspl it will work

improwise said:
Thanks for the feedback!
Just be be sure, "into bootloader mode" is when you start the device holding down volume down and powerkey until you see the tricolor screen? Then that is probably what I have tried to do for a while now without success (total success that is, I do get into the tricolored screen)). Or maybe I am doing something wrong, could you perhaps point to a detailed explaination besides the one in "HardSPL" thread?
USPL I havnt tried, will do that! Is it still so that trying to do USPL on Vista is asking for trouble?
I read somewhere that Stock ROMs should only be flashed from internal storage, not SD cards, is that true? If so, how do I go about accessing that storage now when it doesnt show up in the file explorer on my PC (PC recognizes it as USB device, "HTC Sync" but I get no file access to it).
Click to expand...
Click to collapse
bootloader mode is when you power off the device and hold the volume button down and press power till you get the tricolor screen...
so here is what you need to do .
1. remove the sd card
2. go into the tricolor mode connect your device to the pc and make sure it says (USB) at the bottom
3. run the stock shipped exe from you pc
if that didn't work then you should try the USPL version.. and there is a guide if you are using vista.. i just tried and worked fine.. here it is
http://forum.xda-developers.com/showpost.php?p=3331078&postcount=153
and the reason i'm asking you to remove the sd card because if you have a rom (blacimg.nbh) it won't let you do anything it will try to flash from the sd card and right now you don't want to do that.
and you shouldn't put any rom into the internal storage of the phone..

PapaDocta said:
and you shouldn't put any rom into the internal storage of the phone..
Click to expand...
Click to collapse
What happens if you do that? will it try and flash over the flash? Proper *&@! it up?

nicelad_uk said:
What happens if you do that? will it try and flash over the flash? Proper *&@! it up?
Click to expand...
Click to collapse
i don't think anything would happen... the file will get deleted when you flash as the rest of the files in the internal memory

Thank you everyone! The USPL thing solved it, when I did it from a XP machine! The once bricked Blackstone is not alive an kicking again!
About USPL, I saw the workaround for Vista, but downgrading a few components to make it work just doesn't seem like a safe way to do it. And I cant help but to think that it might have unwanted side affects, ie affecting system stability. But maybe I am wrong?

Going back to shipped ROM without bricking?
Hi,
After reading this thread I am now a bit worried and, as a newbie, would appreciate maybe a "simple" answer to my question.
I''ve been experimenting with various cooked ROMs after following the guide in the WIKI for installing HardSPL and then putting the ROM file (BLACKIMG.nbh) on my SD card and installing it using the power on + volume down button method.
However, I now want to revert back to the original "shipped" ROM, which I have downloaded from the list of shipped ROMs via the WIKI (I downloaded the one which closely matched what was originally on my HD - as I didn't know how to backup the actual ROM on my HD at the time).
So, my question:
How should I put the downloaded original/shipped ROM:
RUU_BlackStone_HTC_WWE_1.14.405.3_Radio_52.49a.25.26_1.09.25.14_Ship.exe
into my HD without bricking it?! Do I just run it on my PC with ActiveSync enabled or do I need to do something to remove the HardSPL or something first?
Sorry if this has been answered previously but I get confused when a thread just makes loads of references to SPLthis and SPLthat etc.!

if you have the HardSPL already installed on your phone then you don't need to do anything more.. just connect your phone to the pc and let it sync (activesync enabled) and flash to any shipped rom you want by simply running the exe file..

PapaDocta said:
if you have the HardSPL already installed on your phone then you don't need to do anything more.. just connect your phone to the pc and let it sync (activesync enabled) and flash to any shipped rom you want by simply running the exe file..
Click to expand...
Click to collapse
Brilliant! Thanks for the simple answer Worked no problem!

Xperia brainfart: Problems with flashing

So people around here sometimes get troubled with regular flashing that doesn't work anymore.
I'll explain my problem on this part:
I flashed to a new ROM just to find out that i didn't like the content so i wanted to flash back to TOUCH X.
I did the usual stuff to flash my phone with, Hardspl, then bootloader etc. etc.
PROBLEM!
Now all my phone seems to be doing is go into bootlader and start updating. However, after 3 seconds i get the message that the update is complete. My phone resets itself, and i found out that nothing has changed. I tried it a number of other times, without results.
Now my question is: is there any other way to do this, this is obviously not working!
post all your ideas here so other people can read this in case that they have the same problem!

Everytime you flash a ROM, you do not need to hardspl your device, only once...I would reformat your memory card,use a stock original rom and see if it will flash with that....usually the issue you are seeing is because the nbh file is not being read properly, make sure your nbh file is named correctly.I have had the issue earlier in my days where if I copied the nbh file through active sync something gets screwed in the transfer...used an external card reader and copied it to my memory card after formatting it and it went through....just some suggestions....Good Luck
Regards,
WC

didn't solve it at all.
More suggestions?

SyntheticDistortion said:
didn't solve it at all.
More suggestions?
Click to expand...
Click to collapse
seems to be your problem? ---> CLICK

Nope, didn't do anything..
Any other suggestions?
EDIT: Really a lot of thanks for anyone helping, i really would love to start flashing again!

grateful for the help arnt you..

try flashing the USB method, if it works its probably due to your memory card. (unless ur already using the usb method, then try the memory card method!)

How do i use the USB method exactly?
And really guys, thanks for all the feedback, maybe make this a sticky for future reference?

SyntheticDistortion said:
How do i use the USB method exactly?
And really guys, thanks for all the feedback, maybe make this a sticky for future reference?
Click to expand...
Click to collapse
well what you do is download the file attached to this post (it is available in one of the stickies but when i tried to download it, it failed so i zipped this one up for you)
extract the .exe within to where your nbh file is (not on xperia, on computer)
make sure there is no KOVSIMG.nbh on your memory card!
put your phone in bootloader (tricolour screen) and plug in via USB
run the custom_RUU.exe and follow the prompts pressing next etc.
you don't have to sync via activesync 1st like it says.
ignore the version number of the ROM just make sure your using the correct nbh and flash!

urm i think you should at least try to look at the stickies .........
this is very useful. i had problem flashing using micro sd so all my flashes are via usb.
http://forum.xda-developers.com/showthread.php?t=497511

That seemed to have done the trick people!
Thanks very much and keep up the good work!

Can't Flash

A few days ago I could not boot my X1 after flashing to a new rom. It came up with "Loading" and no image found. I was able to recover it with MTTY using a windows XP machine. I am now trying to flash to the newest version of CHristian's rom but I can't even hard SPL without getting stuck at the "loading page" again. I am able to pull the battery out and place it back in to boot back up to the OS. I also tried to do the SD card method and that didnt work.
I think something is wonky as last time I hard SPL'd it was a "success" but it just reloaded an old version of Christians Rom.
Please help. I have searched high and low on the forums and all i can find is people with the problem but no answers.
Thank you!

hey im nt no expert but have you tryied hard reseting the device to default settings, then formatting your memory card and then trying to port the rom across? i wonder if that would help!

confusedtadpole said:
hey im nt no expert but have you tryied hard reseting the device to default settings, then formatting your memory card and then trying to port the rom across? i wonder if that would help!
Click to expand...
Click to collapse
I did and it loads to Christians rom...

Please help...not sure if a moderator should move this to another thread or not

Shameless bump here. I still have not been able to resolve this. I can not seem to Hard SPL.

Answer:
I used the SSPL method from http://forum.xda-developers.com/showthread.php?t=431218 to finally get Hard SPL to work.
Hope this helps other people

Please Please someone help me! tmobile uk g1

Hi all,
I’m in desperate need of some of your wealth of experience, i have managed to root and flash my g1 with - rc9 JFv1.51_CRB43-EU.zip (Jesus freke), and recovery-RA-dream-v1.6.2.img recovery image!. Now i want to update to a newer rom!
Now for the problem, the recovery program allows me to flash many of the rom's available but none of them work after the flash completes it just loads the g1 screen and stops there i have left it on that screen for about 10 min’s and nothing at all happens, but then it will allow me to flash back to rc9 JFv1.51_CRB43-EU.zip absolutely fine no issues every time?. Do i need to install anything else before updating to Open Eclare 2.1.1 or SuperD1103-blk.? I’m in the UK with a UK g1 mobile if that makes a difference?

crusader0071 said:
Now for the problem, the recovery program allows me to flash many of the rom's available but none of them work after the flash completes it just loads the g1 screen and stops there i have left it on that screen for about 10 min’s and nothing at all happens, but then it will allow me to flash back to rc9 JFv1.51_CRB43-EU.zip absolutely fine no issues every time?.
Click to expand...
Click to collapse
Just use the top three wipes available in Anon's recovery menu: Wipe System/Data (1st), Davilk Cache (2nd), Ext Partition (3rd). If you haven't partitioned your SD card into FAT32, Ext2, 3, or 4 and Linux-Swap, do so now with the Recovery menu. You must backup your fat32 first, because a total repartition will totally blank your data. Good luck!

crusader0071 said:
Hi all,
I’m in desperate need of some of your wealth of experience, i have managed to root and flash my g1 with - rc9 JFv1.51_CRB43-EU.zip (Jesus freke), and recovery-RA-dream-v1.6.2.img recovery image!. Now i want to update to a newer rom!
Now for the problem, the recovery program allows me to flash many of the rom's available but none of them work after the flash completes it just loads the g1 screen and stops there i have left it on that screen for about 10 min’s and nothing at all happens, but then it will allow me to flash back to rc9 JFv1.51_CRB43-EU.zip absolutely fine no issues every time?. Do i need to install anything else before updating to Open Eclare 2.1.1 or SuperD1103-blk.? I’m in the UK with a UK g1 mobile if that makes a difference?
Click to expand...
Click to collapse
Make sure you partition your sd card and then try like the above said....or maybe try flashing death spl.
http://forum.xda-developers.com/showthread.php?t=625886&highlight=Death

thanks for trying to help but....
hi thanks for your help but ...
i have partitioned the card via anons recovery flasher, i have set my 8gb to 96mb swap , 1.5gb ext2 and the rest is used for fat32.
i have also gone throught the menu and deleted / erased the top 3 as requested but when i install a new rom it still freezes on the g1 welcome screen? please help!

G1ForFun said:
Make sure you partition your sd card and then try like the above said....or maybe try flashing death spl.
http://forum.xda-developers.com/showthread.php?t=625886&highlight=Death
Click to expand...
Click to collapse
hi i just noticed im using Hard Spl update at the moment ? how do i update to Haykuro?

i think i have totaly broke my phone? - i downloaded haykuros spl and flashed it via the anons recovers flash image from sd card, and now i can no longer get in to the recover menu? and no fast boot please please help me !

crusader0071 said:
i think i have totaly broke my phone? - i downloaded haykuros spl and flashed it via the anons recovers flash image from sd card, and now i can no longer get in to the recover menu? and no fast boot please please help me !
Click to expand...
Click to collapse
This is YOUR FAULT for NOT READING!!!!
You installed an SPL meant for an HTC MAGIC onto your HTC DREAM. It *CAN* be made to work, HOWEVER, you failed to read and understand what is required to actually do it safely.
SPECIFICALLY, you are stuck in boot mode 3 -- boot to recovery, and because you changed the SPL, your recovery partition is UNABLE TO BOOT.
You are BRICKED, and the only way out is to use a hardware interface called "JTAG", which requires you to disassemble the phone.
SPECIFICALLY:
You missed the part of that thread that says "MOD EDIT PLEASE READ THIS THREAD FOR UP TO DATE INFORMATION".
I have no sympathy for you. That instruction is in big purple letters.

hi thanks for your info, do you know anyone or anywhere i can get my phone jtagged?

How could you mess it up with step by step instructions....lol...I am being dead serious....it doesn't get more clear than this.
IMPORTANT: Before going any further make sure that you have PVT board. You can do this by rebooting your phone and holding the camera button. The first line should say "PVT" if you see "DVT" then DO NOT flash this because odds are you will get a brick but If it says "PVT" then you are good to go.
First you are going to need to download the latest radio and the SPL. both can be found here http://code.google.com/p/sapphire-port-dream/ There is also a new radio that is compatible that can be found here http://forum.xda-developers.com/showthread.php?t=640535
Prior to starting the installation process please make sure that your battery has a good charge. Also DO NOT pull your battery out at anytime during the installation process. I know it seems like common sense but I read a thread where someone had pulled their battery in the middle of the installation process and they ended up with a brick.
Now that all that's out of the way lets get started!
1. Copy "ota-radio-2_22_19_26I.zip" or "G1-radio-2_22_23_02.zip" and "spl-signed.zip" onto the root of your SD card.
2. Reboot into recovery. I suggest using the RA-dream recovery you can download it here http://forum.xda-developers.com/showthread.php?t=566669
3. Wipe your phone "factory data reset" (this step isnt really necessary since your phone is wiped after flashing the SPL but I always like to wipe before flashing anything)
DO NOT SKIP THIS NEXT STEP OR YOU WILL BRICK YOUR PHONE
You must have the latest radio "2_22_19_26I" or "2_22_23_02" to flash this SPL if you already have the latest radio you should not have to flash it again but it will not hurt if you do flash it again. When in doubt flash it anyway.
4. Flash the Radio "ota-radio-2_22_19_26I.zip" or "G1-radio-2_22_23_02.zip" it will install and then it will ask you to reboot to finish the installation, so reboot, it will then finish installing and then reboot back into recovery.
5. Flash the SPL "spl-signed.zip" it will install and then ask you to reboot to finish the installation, so reboot, it will then finish installing and reboot into recovery so you can flash your ROM

i cant get in to fast boot or recovery i just get the g1 screen, if i press camera and power or if i press home and power i just get the g1 nothing else

crusader0071 said:
i cant get in to fast boot or recovery i just get the g1 screen, if i press camera and power or if i press home and power i just get the g1 nothing else
Click to expand...
Click to collapse
Did you follow those steps when flashing the SPL? Did you even flash the radio before flashing the SPL?
It sounds like you have no idea what you did to your phone which is never a good sign (and usually means you shouldn't even be flashing custom radios/spl's/roms)

no i did not, i was asking for help for the last 2 or 3 days? i did what i thought was right but it was not. can i fix it or not?

heres what you do
ive did this too lmao jus go here www*androidhustler*blogspot*com ( THE * ARE REPLACEMENTS FOR . BECAUSE I CANT POST A OUTSIDE LINK SO U GET WUT IM SAYING SWITCH THE * WITH A . ) THEN SCROLL DWN TO A POST CALLED THE 2010 HOW TO GET CYANOGEN LATEST. DO ALL STEPS AND DONT RUSH. IF YOURE G1 DOESNT BOOT UP PROPERLY THEN I QUIT THIS SHYT BRO. LOL FOR REAL AND IF U HAVE ANY QUESTION EMAIL ME AT [email protected]*COM

crusader0071 said:
no i did not, i was asking for help for the last 2 or 3 days? i did what i thought was right but it was not. can i fix it or not?
Click to expand...
Click to collapse
Sigh....I would go buy another phone off Craigslist or something similar.
Next time...please read before flashing....Although I'm sure you will after the last mishap.

the only way to fix your phone is to buy a doner phone with a broken screen or something cheap off of ebay
there is NO KNOWN WAY to fix it without a doner (the jtag method isnt do-able yet)

I know here in town...there are so many G1's up for sale around the $150 mark in really really nice condition.
That's where I'd be looking if I bricked my G1. Well...I'd be replacing it with a HD2 probably...lol

garok89 said:
the only way to fix your phone is to buy a doner phone with a broken screen or something cheap off of ebay
there is NO KNOWN WAY to fix it without a doner (the jtag method isnt do-able yet)
Click to expand...
Click to collapse
What do you mean by jtag method isn't do-able?
ezterry did mine without an issue.

details
Sleeepy2 said:
What do you mean by jtag method isn't do-able?
ezterry did mine without an issue.
Click to expand...
Click to collapse
have you got contact details for ezterry? if so pm me please.

as far as i can see the jtag is still in testing?

This noob is in the UK anyways. Let him figure it out.
Wrong section, soft bricked his own phone and freaking out.
Please READ. You are from the UK so your English isn't bad. You have no excuse for not following instructions.
Ways to fix your phone:
1) motherboard replacement
2) JTAG (experts are not anywhere near you though)
3) buy a new phone
Mods please get this out of here

touch screen does not work at all

Hello. Yesterday morning when i woke up suddenly my touch screen did not respond any more. I try reinstalling windows or hard reset but now i can not even get over tap the screen.Please help me. You already helped me once when i was going to throw it away because i thought it's a hardware problem and it was a software one.I did the soft reset and leave it for a day then it worked but when i wanted to charge, it happened again and i have the same problem now.Any way a thing it's certain it is a software problem.If you have other advice please help.

another problem
I tried installing lots of roms hoping it will be fine. but now i installed a 6.1 version of wm and when i try installing wm 6.5 it stopes in loading screen and the pc gives me an error conection.What about this?

Moved as not ROM Development.
Place a welcome.not file on root of storage card can be a .txt file but change the extension doesn't want to be welcome.not.txt this will get you past all the configs on setup.

Please be more specific
Where can i find a welcome.not file?

linucu said:
Where can i find a welcome.not file?
Click to expand...
Click to collapse
You make it out of a .txt file
Have done it 4 u.

Thank you but that was not the problem
I did as you said and it worked but that was not the problem.The problem is my touch screen not responding.And it's not a hardware problem because if i did as i have been told to fully charge the phone, then do a soft reset and leave it for a day it was as new.But when i try to charge it again i got the same not responding screen. Now after all this i have another issue and that is when i try doing a soft reset the phone resets and it sopped on gray screen with Loading... and the pc gives me error connection. So i get this only i put a 6.1wm. Is this the reason for not letting me change the wm to 6.5 one? i will go crazy with these strange things that are science but have no explanation. Where is the science then? What you did was to allow me to use the phone without touch screen. Well...thank you, but i know there is a way to get the phone normal again and that is what i need you to help me with. Thank you. Catalin

Are you Hard-SPL'd?
Regards problem if software then flashing a different ROM even stock should be able to tell you, i know you think not hardware but if repetitive then maybe you just fluked the being ok again.
Anyway flash another stock ROM, then if fine flash a 6.5, you don't have to use computer as can flash via SD.

First of all thank you
Thank you because you try to help but please talk so i can understand. What is stock rom?
"even stock should be able to tell you" what is stock?
And now i have another one. It can not connect to active sync.
tell me please how can i Flash form SD?

I can not insatll anything from pc
So i don't understand why it does not allow me to do anything like hard spl, or flash rom, or anything to install from pc. It connects to active sync and lets me access the card but when i try installing something it stops.