Since a few months I have been experiencing some serious issues with my TyTN II.
After being on for a while, it displays either:
No Service - While the reception in the area is just fine. Switching 'Phone' off and on in the Comm Manager fixes this problem, but then after maybe half an hour the same thing happens
Sim Card Missing - Apparently it can't read the SIM, a soft-reset usually helps in this situation.
I have tried several ROMs and Radios, and I even had the SIM-reader in the phone replaced. The SIM-card itself works fine in several other phones.
Does anyone have any experience with this? Any other suggestions as to what I could do? Any help would be greatly appreciated! Thanks.
tjado said:
Since a few months I have been experiencing some serious issues with my TyTN II.
After being on for a while, it displays either:
No Service - While the reception in the area is just fine. Switching 'Phone' off and on in the Comm Manager fixes this problem, but then after maybe half an hour the same thing happens
Sim Card Missing - Apparently it can't read the SIM, a soft-reset usually helps in this situation.
I have tried several ROMs and Radios, and I even had the SIM-reader in the phone replaced. The SIM-card itself works fine in several other phones.
Does anyone have any experience with this? Any other suggestions as to what I could do? Any help would be greatly appreciated! Thanks.
Click to expand...
Click to collapse
Have you tried other sim card on your phone and see what happens? Have you checked the sim card slot and see if there is nothing that's interfering the phone signal?
this is the same thing that is happening to me and there is no obstruction or anything interfering with the sim card connecting to the phone eventually i gave up on looking for a fix. So now i reverted to using my opal So the TyTn II just became my pocket pc now im going to flash wm6.5 jijijijijijjijiji but if somebody finds a fix please post it cause the tytn II was awesome but now its dead.
Same problem here
I'm having the same problem here. Already changing the sim flex and sim card reader, but still no improvement. Is there anything that I can do for this problem?
does anybody ever changing the upper board? is there any result?
same thing hapened to me..
tried sim in another phone and it works, tried another sim in the kaiser and no sim detected??
almost the same problem with my 8925
I have WM6.1 on it. It some time has a good reception, but in several minutes it says The SIM card is missing. Then it (not always, but sometimes) finds SIM itself. strange thing is, that if I flash WM6.5, it has almost no problems but it looses sound and camera doesn't work either...
Any ideas?
Thanks beforehand!
Tried Sim Card Flex replaced.
tjado said:
Since a few months I have been experiencing some serious issues with my TyTN II.
After being on for a while, it displays either:
No Service - While the reception in the area is just fine. Switching 'Phone' off and on in the Comm Manager fixes this problem, but then after maybe half an hour the same thing happens
Sim Card Missing - Apparently it can't read the SIM, a soft-reset usually helps in this situation.
I have tried several ROMs and Radios, and I even had the SIM-reader in the phone replaced. The SIM-card itself works fine in several other phones.
Does anyone have any experience with this? Any other suggestions as to what I could do? Any help would be greatly appreciated! Thanks.
Click to expand...
Click to collapse
> I did exactly just all that, using a Windows Mobile 6.5 Rom.
> After replacing the Sim Card Flex but Sim card still unreadable.
> Currently using back my Wizard, was thinking of changing the Flex Ribbon Cable but skeptical it will work unless someone have tried it.
> Found it on Ebay, check it out.
> http://cgi.ebay.com.sg/ws/eBayISAPI.dll?ViewItem&item=280555578532&ssPageName=STRK:MEWAX:IT
> Hope this helps abit
Almost the same with my Kaiser. The only difference, it doesn't show "No Service" message, shows network icon and name, but not available for calling. From time to time becomes available, after few seconds no more! After several hours of such unstable working, drops network at all, with no chanse of restoring it unless switching phone off/on. After that, performing as before.
I have installed a numerous versions of Roms and Radios, ranging from WM6.0 to WM6.5, tried Android, tried almost every combination of band, frequency, hsdpa and data setting with no help.
Is it possible hardware failure?
I did notice a micro switch in the sim card slot when I was tearing down my unit.. perhaps you want to play with the switch to see if other position may solve your issue.
same issue here...
tried everything...
Dear All,
Have you tried to connect an GSM external antenna to check if it improves the reception ?
Regards,
Nino
Sorry for my english.
I found this problem too.( no service)
My solution is
1. I format rom by use MTTY tool.
(1. How to check and repair bad block
a). Please make sure that you are SuperCID and you understand the importance of hard spl as this maybe a dangerious operation for you.
b). Download Mtty.exe file in the attachment below and save it to your computer.
c). Open connection setting of your activesync or WMDC on your PC and disable "Allow USB connection".
d). Put your divice into Bootloader mode and connect to your PC via USB
e). Run Mtty.exe from your PC
f). Selec "USB" in port box and then click OK
g). Press Enter once or twice to let the screen dispay "USB>" or "CMD>"
h). Type "info 8" to check if your device has bad blocks. And if there are any,
i). Type "task 2a" to fix the bad blocks.
2. Flash Rom again.
3. Now Signal come.
mtty fix
has anyone tried this? I'm having the same problem where my phone says no service and sim card missing, but i'm afraid to be the first to try this mtty fix as i've never used it before. Can someone confirm that it will fix this problem? Thanks to the guy that put it up ^
aekapolm said:
...My solution is....
Click to expand...
Click to collapse
master aekapolm...
i will try your solution!
aekapolm said:
...
h). Type "info 8" to check if your device has bad blocks. And if there are any,
i). Type "task 2a" to fix the bad blocks...
Click to expand...
Click to collapse
after "info 8" my kaiser formatted... and i can not type "task 2a" ??????
i'm planning to change the flex cable cause mine has a cut in the middle and need to change the lcd due to crack
It's not the SIM card or the switch. That switch you're referring to will shut the phone off in the event that the SIM door is opened.
As for the "no service" issue, I understand that the HSPDA/3G radio part of the phone tends to go bad, especially with certain radio SPLs'. Once it's gone, it's gone for good. The only way to restore functionality is to replace the lower board which contains the radio, which includes the NAND (all your precious data).
I have seen some success with people using the 1.70 series of radio versions but it does not restore 3G/HSPDA, only 2G is functional, and the way networks are changing over to 4G, I don't see much of a future for 2G devices.
My advice... Find a replacement Kaiser with a cracked screen or other problem that doesn't involve the lower board and swap parts.
Out of curiosity, and asking for a mod to help on this:
This post is teaching newbies to KILL their phones, why was this thread revived?
Any newcomer please DON`T DO THE STEPS BELOW!! It will kill your phone.
aekapolm said:
Sorry for my english.
I found this problem too.( no service)
My solution is
1. I format rom by use MTTY tool.
(1. How to check and repair bad block
a). Please make sure that you are SuperCID and you understand the importance of hard spl as this maybe a dangerious operation for you.
b). Download Mtty.exe file in the attachment below and save it to your computer.
c). Open connection setting of your activesync or WMDC on your PC and disable "Allow USB connection".
d). Put your divice into Bootloader mode and connect to your PC via USB
e). Run Mtty.exe from your PC
f). Selec "USB" in port box and then click OK
g). Press Enter once or twice to let the screen dispay "USB>" or "CMD>"
h). Type "info 8" to check if your device has bad blocks. And if there are any,
i). Type "task 2a" to fix the bad blocks.
2. Flash Rom again.
3. Now Signal come.
Click to expand...
Click to collapse
Related
Hi all - I have a weird problem for which I am hoping people here would have a resolution. Recently bought a Tytn II,
ROM Version 1.81.415.4 WWE
ROM Date 10/29/07
Radio Version 1.27.15.32
Protocol version 22.51.88.13W
Using with a 2 GB memory card
Now, i have noticed a few times that the device just does not come out from the standby mode - the Green LED indicating that the GSM is on is flashing, but when I try to call into it using anothe rphone, it indicates being switched off or not reachable. I try to start is using the power key, or any number of keys without luck - the only way out is a soft reset.
I have seen some people quote a similar problem, but not inding a resolution there, am posting this up here
Pls help - I am extremely reliant on this as a business device and will get stuck if it behaves like this
Have you tried a hard reset? I know some radio's/ROM's have this issue
mine started doing that a while back and I found that it was a combination of my phone automaticly reciving an email while it was asleep and this program I had that gave you points for AP's and cell towers I forget what its called after I got rid of that program and changed my email to retrive manually the problem stoped
What apps would I need after a hard reset ?
KDKobes said:
Have you tried a hard reset? I know some radio's/ROM's have this issue
Click to expand...
Click to collapse
Hi - thanks for the valuable advice. I would do so - however, another problem is compounding the same - I got this from a friend, and dont have the getting started CD that comes with the pack - can you tell me about, on a hard reset, what apps would I need to reload from the getting started CD? Or would I not need the CD ? I have all the other contact data with me on Outlook, and the other files I have copies of on the computer, so I don't plan to use a backup/ restore.
The only thing I have noticed that gets changed is the sensitivity resets to default usually which can be changed back in KaiserTweak or Advanced Configuration. I would say if you have never done any ROM or Radio changes to the device, and its a new phone its probably got something wrong with it. That gives you 2 options. 1 - take it back and get it replaced if you can, or 2 - follow the WIKI and change you ROM/Radio, but read WIKI because you will need to HardSPl before flashing anything.
I had the Standby of Death SOD this is when the phone fails to come out of standby with a power button press. This issue only affects some people on some networks. I'm not sure if its a network problem or a software problem but as only a minority of people have it, I suspect its mainly a network problem there is a software solution.
The solution is to change the phone settings band option from auto 3G/2G to either 3G Only (WCDMA + UTMS 2100 in Europe) or 2G Only (GSM + AUTO) depending on your requirements.
Also read this thread http://forum.xda-developers.com/showthread.php?t=540943&highlight=standby&page=2 where the resolution was to get a new SIM.
Obviously this only solves the problem when the crash is because of the sim and/or settings which impact the sim. To rule out a software cause its best to start with a hard reset.
I have the same issue once in a while. In my case gwes.exe hangs at that point which after that i have to soft reset. Still have no fix found though
I'm sorry but my fix wont work for you as its only for people whose phones only crash in standby there is no gwes.exe hang associated with it. Obviously it only solves the problem when the crash is because of the sim and/or settings which impact the sim. To rule out a software cause its best to start with a hard reset.
@nlel
I allready tried a hard reset but the problem returns after a certain time.
The gwes.exe does not hang when using the device, it only hangs when resuming from standby and does not allways occur.
Well in your case its very obviously a software or hardware problem and nothing to do with the SIM and/or settings which impact the SIM. I don't know what else to suggest if my solution doesn't help I don't know what else you can try to do btw how do you know gwes.exe is crashing when resuming from standby.
When it happens to me (because of phone band type set to auto) I cannot see what is happening on the phone at that precise moment as I have to soft reset. There is nothing that is obviously crashing at the same time.
By the way gwes.exe according to MSDN, its Graphics, Windowing, and Events Subsystem. GWES loads display drivers, printer drivers, and touch screen drivers, maybe you have a hardware fault.
Does it happen to both your Tytn II's?? and have you tried my solution or a new SIM ?
Hi all,
I wonder if anyone can resolve/give suggestion for my problem.
Basically i have experience problems connecting via Wi-Fi i.e the after activating wi-fi the phone will scan for available networks and give you the list. I then try to connect to my router (bt home hub which is actually speed touch) it does connect and stays connected for some time then suddenly the connection is dropped and under wifi it says that my access point is unavailable. If i turn wifi off/on again and scan for networks it comes up with "No visible Networks detected" even though there are like 5 access points in my house and i can connect to any of them using my laptop and old nokia e60. If i wait a while it will connect again but will not keep the connection. I have tried at home, work and some public places-every time is the same story.
Things i tried:
Soft reset/hard reset (many times)
Tried disabling phone radio in case3g chip interrupts
I tried with secure networks, open networks, different types of authentication/encryption, different router (more than 10) and every its the same story. I also tried several ROMS and ALL RADIO's available with the same result.
I am currently on Duttys_Diamv2.3 WWE RADIO 1.00.25.08, its a clean flash, nothing else is installed. I also have SPL-1.40Olinex installed (not sure if that could have an impact) The phone is vodafone branded btw (i had the same issue with vodafone rom which is why i decided to try other roms). I wonder if anyone has any thoughts/suggestions and would appreciate any help. Thanks in advance.
The same situation happened to my Diamond. I took it to the local dealer for HTC and after several days, I am told that the main board will need replacement. I am still waiting for it to be repaired as the parts had to be braught in from another country. I was also saud if the phone was less than a month old (which it is not) they would have replaced it with a new phone.
Good luck repairing yours and keep us updated.
omar302 said:
The same situation happened to my Diamond. I took it to the local dealer for HTC and after several days, I am told that the main board will need replacement. I am still waiting for it to be repaired as the parts had to be braught in from another country. I was also saud if the phone was less than a month old (which it is not) they would have replaced it with a new phone.
Good luck repairing yours and keep us updated.
Click to expand...
Click to collapse
Thanks Omar, I was kinda thinking that it may be hardware issue, but I don't anymore, I am trying something else actually as we speak. The only thing I haven't tried before is another hard SPL and I think that's the problem, I installed another version hspl1.34 and it seems more stable now and wifi keep connection, also with another hspl version (it was hspl 1.24) RAM under devise info>hardware showed 128, now it is 192. I will test in intensively and post my results here in case nay one else have the same issue. Hopefully I will not have to send it away for repair. Thanks for your info anyways.
In risk of sounding lame ...
Have ya tried 'Start' / 'Settings' / 'System' 'Wireless LAN'
Under Wireless LAN click 3'rd tab (strømtilstand in Danish - could be power-settings)
On that tab - pull the marker way to the left in order not to minimize the power consumption when tryng to hookup with the WiFi.
I had massive problems to get my local WiFi working at home - until I did this trick.
Best luck, Kindly
Kwasmir said:
In risk of sounding lame ...
Have ya tried 'Start' / 'Settings' / 'System' 'Wireless LAN'
Under Wireless LAN click 3'rd tab (strømtilstand in Danish - could be power-settings)
On that tab - pull the marker way to the left in order not to minimize the power consumption when tryng to hookup with the WiFi.
I had massive problems to get my local WiFi working at home - until I did this trick.
Best luck, Kindly
Click to expand...
Click to collapse
Yes i have thats the first thin you do anyways . I am now more than sure that the issue was with HSPL version 1.34, as soon as i got rid of it (installed hspl 1.24) all is fine.
With my phone, i tired all Hard SPL versions and even went back to stock SPL & Rom 1.37 & 1.93 and it still didn't fix the WIFI issue. it will work for 5-15 minutes then it will not work.
Anyway, I got a replacement phone as apparently they couldn't fix it.
pufeks said:
Hi all,
I wonder if anyone can resolve/give suggestion for my problem.
Basically i have experience problems connecting via Wi-Fi i.e the after activating wi-fi the phone will scan for available networks and give you the list. I then try to connect to my router (bt home hub which is actually speed touch) it does connect and stays connected for some time then suddenly the connection is dropped and under wifi it says that my access point is unavailable. If i turn wifi off/on again and scan for networks it comes up with "No visible Networks detected" even though there are like 5 access points in my house and i can connect to any of them using my laptop and old nokia e60. If i wait a while it will connect again but will not keep the connection. I have tried at home, work and some public places-every time is the same story.
Things i tried:
Soft reset/hard reset (many times)
Tried disabling phone radio in case3g chip interrupts
I tried with secure networks, open networks, different types of authentication/encryption, different router (more than 10) and every its the same story. I also tried several ROMS and ALL RADIO's available with the same result.
I am currently on Duttys_Diamv2.3 WWE RADIO 1.00.25.08, its a clean flash, nothing else is installed. I also have SPL-1.40Olinex installed (not sure if that could have an impact) The phone is vodafone branded btw (i had the same issue with vodafone rom which is why i decided to try other roms). I wonder if anyone has any thoughts/suggestions and would appreciate any help. Thanks in advance.
Click to expand...
Click to collapse
...I have the same problems with you
However, I think the problem may caused by different ROM versions.
My hTC version Diamond initially flashed a Chinese version ROM, and the WiFi connects well, while I changed to Dutty's most updated ROM, this problem comes and I cannot figure out why untill now.
Some friends also suggested to go to the Power Management and change WiFi to "Best Performance", I tried and failed again.
WiFi can open and connect to Routers located in library of my university, nevertheless it cannot open any pages.
I'm also waiting for any person that can solve the problem and then help us figure out why....
thanks in advance!
I got the same problem as most of the people have. and i think "Fail to turn on wifi" is a very common among guyz who got HTC TD.
I dont know what should be done, i almost tried every thing. actually my phone was locked to 3 mobile Sweden and i unlocked it but my wifi was'nt working before unlocking too but i did'nt gave attention to it. Now i noticed it.. is that any one know how to lock it again soo that i can send my mobile for repairs or, any one know what should i do.
I would recommend upgrading your radio and your rom.
Ive been rocking the setup in my sig for some weeks now and its been flawless, stable and fast.
which rom and radio you are using. can you please help me in this matter.
and i think its not a hardware problem because its showing that hardware is connected to my device as its shown in the screen shoot
Hi,
Im using AlphaZero V7 NLD,
Im have 1 wifi point in my house, downstairs.
even when im on the attic i have 80% signal strengt.
My router is a draytek 2820G router.
Wifi for me is very good. .. correctly, AZTOR V7 NLD is very good for me.
im on t-mobile network.
Radio Radio v1.00.25.05 , Radio v1.00.25.08, Radio v1.00.25.16, where all good,
now testing Radio v1.08.25.20, HDSPA signal is bit weaker atm.
my best radia atm i think, v1.00.25.08.
im betting, that the starter of this toppic, who has 5 access points in his house all have the same SSID. This is not the way.
Or make 1 big AP aera, bij connecting the AP's to each other.
of try to set every AP its own SSID, and its own Channel.
Louis
WIFI problem in HTC Diamond.........
I am trying connecting to my home wireless network. It finds the network but unable to connect to it. Any help please? Has anyone managed to get it connected to any Wifi? I ahve already set the power management to "best performace...no succes.......
(My laptop and O2 stealth does get connected to the same network and it an open wifi connection)...........PLZ Help.....
pranavsethi said:
I am trying connecting to my home wireless network. It finds the network but unable to connect to it. Any help please? Has anyone managed to get it connected to any Wifi? I ahve already set the power management to "best performace...no succes.......
(My laptop and O2 stealth does get connected to the same network and it an open wifi connection)...........PLZ Help.....
Click to expand...
Click to collapse
i am also having this problem, it can find the network, and can spend a minute or 2 trying to connect, and nothing happens. you posted this in february, did you find an answer?
Wifi & Bluetooth not detected by HTC Diamond
Someone pl help. My HTC Diamond is not detecting bluetooth devices neither is detecting wifi. It was earlier doing so and working fine however I believe after installing tweak TD & t3d config it has stopped working. I have installed new ROM also but to no avail. Can someone pl help!!!!!!!!
Wintermoonlight said:
i am also having this problem, it can find the network, and can spend a minute or 2 trying to connect, and nothing happens. you posted this in february, did you find an answer?
Click to expand...
Click to collapse
i also have the same problem. it detects a wifi (my router at home Aztech brand), then trying to connect to it, and then it always showed the wifi as "unavailable". i put my phone 2 mm distance from the antenna of my router it also won't connect. i have change dozens of roms, win 6.1, 6.5, 6.5.1, different cook, MTTY, all with no success.
i've looked for internet and google for answers, i seen quite a lot of forum has described this issue, but with no solution. most of the ppl suggest in various forums to pull the wireless slider to "Best Performance", ofcourse i have done that, but is just the same result.
i'm still trying searching for a solution for this, i hope is not a hardware issue because my warranty has already ended. i'm currently using Gen Y R4.1B rom
pufeks said:
Yes i have thats the first thin you do anyways . I am now more than sure that the issue was with HSPL version 1.34, as soon as i got rid of it (installed hspl 1.24) all is fine.
Click to expand...
Click to collapse
Ok consider now wifi will work by re-flashing the spl.
But what is the relation between spl (os/winmo loader) with wifi?
another dang unsolved diamond wifi?
bravo.
same problem with wifi on diamond2
With Original stock WM6.1 i was unable to connect at all, after flashed official WM6.5 upgrade everything worked fine. However i decided to put cooked rom because of battery life and perfomance issues. Dutty HG6 for Topaz seems to be with glitchy radio, it works sometimes, very rare, and i'm still not up to the pattern when does it happen and why. Pretty sure it's not a hardware problem - so everybody relax, we will find the solution.
which rom and radio you are using. can you please help me in this matter.
and i think its not a hardware problem because its showing that hardware is connected to my device as its shown in the screen shoot
wjenya said:
With Original stock WM6.1 i was unable to connect at all, after flashed official WM6.5 upgrade everything worked fine. However i decided to put cooked rom because of battery life and perfomance issues. Dutty HG6 for Topaz seems to be with glitchy radio, it works sometimes, very rare, and i'm still not up to the pattern when does it happen and why. Pretty sure it's not a hardware problem - so everybody relax, we will find the solution.
Click to expand...
Click to collapse
nope, i also put Gen.Y WM6.5 then the problem still arise.
i'll wait any solution until my diamond is totally wrecked
Last night i was playing with my gps ( Navigon - Google Maps - Google Nav) I switch the phone off at the comm Manager and left it off like that the whole night.
This morning when i switched it on, the phone refused to receive any signal.
Ive tried the following
Soft Reset
Hard Reset
Different Sims
Switching flight mode on and off aswell as the phone tabs
Ive changed the band from auto to gsm and back and still nothing
Gps, Wifi and everything else still works perfectly.
Before i return it and wait like 50 days for them to fix it, what can i try?
stevh0 said:
Last night i was playing with my gps ( Navigon - Google Maps - Google Nav) I switch the phone off at the comm Manager and left it off like that the whole night.
This morning when i switched it on, the phone refused to receive any signal.
Ive tried the following
Soft Reset
Hard Reset
Different Sims
Switching flight mode on and off aswell as the phone tabs
Ive changed the band from auto to gsm and back and still nothing
Gps, Wifi and everything else still works perfectly.
Before i return it and wait like 50 days for them to fix it, what can i try?
Click to expand...
Click to collapse
More information please. Rom, Radio, SPL?
Also have you tried calling your provider to ask if theres any problems at their end?
Mark.
I have no idea what rom..
lemme check..i have not changed a thing since i took delivery of the phone about 9 11 month ago.
my sim works perfectly in another phone.
rom 1.56.405.5
rom date 08.28.07
radio version 1.27.12.32
Does your sim work perfectly in another phone *in the same location* though? It was suggested you contact your network provider to see if they have any known issues or there are any reasons why your phone shouldn't be working. It may help if you have the IMEI number ready if you are in the UK, in case there is some reason why it has been blacklisted. If your TyTN II wont work with another sim in it (ideally from another network provider) and your usual network provider is unaware of any reason why this should be happening, then as a stock standard TyTN II, I think you'll have a good chance of having it looked at for free under warranty by HTC. Here in the UK I had my ROM reflashed from their WM 6.1 abomination back to the original WM 6.0 version by HTCs repair centre within one day so unless you choose a turtleback express postage option to send it in, there's no way it should take 50 days.
It started working all on its own again? how weird is that?
it had been normal ?
my tytnII had became the same after flight mode had turned on.
when fight mode off, it displayed "no service".
yiwangwuqian020 said:
my tytnII had became the same after flight mode had turned on.
when fight mode off, it displayed "no service".
Click to expand...
Click to collapse
you just use GSM-schen-HTC.Kaiser.CommManager.3G
hi, first thanks a lot,
my tytnII had this commManager software. I just used this commManager to turn on or off this flight mode .
how about no sim detected?
This problem is on my phone ,but this prog is not running perfectly. Error report at cca 95% full "sufficient system permissions"
Sorry for little English!
Please help me
radio:1.65.17.56
rom: through
Gastrocsaba said:
This problem is on my phone ,but this prog is not running perfectly. Error report at cca 95% full "sufficient system permissions"
Sorry for little English!
Please help me
radio:1.65.17.56
rom: through
Click to expand...
Click to collapse
after I reflash this tytn`s rom, it remain no service.
I think it had wrong with its gsm hardware.
Sorry for my english.
I found this problem too.( no service)
My solution is
1. I format rom by use MTTY tool.
(1. How to check and repair bad block
a). Please make sure that you are SuperCID and you understand the importance of hard spl as this maybe a dangerious operation for you.
b). Download Mtty.exe file in the attachment below and save it to your computer.
c). Open connection setting of your activesync or WMDC on your PC and disable "Allow USB connection".
d). Put your divice into Bootloader mode and connect to your PC via USB
e). Run Mtty.exe from your PC
f). Selec "USB" in port box and then click OK
g). Press Enter once or twice to let the screen dispay "USB>" or "CMD>"
h). Type "info 8" to check if your device has bad blocks. And if there are any,
i). Type "task 2a" to fix the bad blocks.
2. Flash Rom again.
3. Now Signal come.
And you turned your Kaiser into a BRICK...
... If your SPL supports "task 2a".
Hello,
Firstly I want excuse that I open new threat and open it here, but please let me explain it why I do it.
I have O2 Stellar, with SPL:1.82.0000 and my USB dont work, and USB connector is OK and cable or USB port too. I try it at diferent PCs with diferent systems aka XP, Vista.
Main problem is that USB dont sync with ActiveSync or other, no "Tada sound" dont show "not recognize" really nothing action when I plug it to USB.
And charging is work only when PDA is off and light RED LIGHT but when is off, than no action, no light, no charging.
I know that this is threat for "Kaiser General" but I can live with charging only when is off, but I cant live withou coocked ROMs, I really try use all HardSPL new Radios, NBH from shippedroms copy to SDcard (Formatted to FAT32) and it only show "LOADING..." but nothing, more, still Loading.
I was tryed JumpSPL but it dont flash from SDcard, and USB is not showing and not working, that I cant use MTTY.
Please let this threat open, I really need HELP
Do someone know if this is Hardware or Sofware problem?
I cant send it to service, from my country is too expensive (like new phone)
Thank you in advance
Jozef Ziak
Edit: The handsfree is working perfect, I really dont know what is it.
i have the same problem i been through three phones already 1 that i used roms on and two brand new ones from warranty att said it's a hardware issue".they are sending me another phone.
I had almost a similar problem with my tilt at one point. Check your usb to pc settings and make sure you have "advance connection" (or something similar I can't remember exactly what it says) checked. On the rom I am using now shows something different there. I says "enable faster data sync" "uncheck if activesync doesn't recognize the device"
Thank you, but nothing reconize my PDA, no sound after plug, nothing when I go manualy to Bootloader, only show serial, not USB
same problem
Hi,
I had the same problem. I tried everything but nothing helped. I had 2 more months of warranty so they changed the main panel. After I got it back from the service it was working for 3 weeks long and now again died with the same issue.
Strange. I have to send it back to the service.
HI there , I had the same problem for about 4 month but i solved it >>> how ?
Just clean your htc USB port and check if it is broken or not and you will see that your issue will be solved brother
Hi All,
I've been running the Orange (UK) WM6.1 ROM for months/years without problems and was messing around with some texts and somewhere along the line I have ended up with the standard 4 stripes down the screen and some text top left.
I have scanned the forums here and the wiki and they suggest connecting using USB and running Mtty.exe, however whilst I can connect the phone using USB Activesync won't recognise it and then I get an error from Mtty.exe because it won't recognise the phone.
I have also tried re-intalling the Orange ROM as well as newer roms, but none of them seem to be able to connect to the phone.
Active sync doesn't seem to be able to connect on Win 7 or Win XP despite them syncing fine this morning.
So, any suggestions out there?
I'll do some more searching, but any pointers would be appreciated.
Thanks.
Try a new USB cable, I went through 5 in one year, or try flashing via SD card.
Well I tried a couple of different leads and no luck.
I did manage to get some info from mtty.exe, but didn't make sense.
I took my SIM out to use in another phone and having left the battery out for a while, put it back in to try again at getting it to start and it booted fine without any problems.
After a bit of messing around it seems like that the boot problem is either down to a problem with the SD card, SIM or a foreign object in phones casing.
I keep the phone in a pocket of my overals that I use a workshop and occasionally iron filings from a grinder can get into it's working, which is what I think has happened.
ANyway, it's back and working again, only need to keep it going until Orange can get some Desire HDs in
Hi!
Read those threads again,the solution is there.
1.Disable USB connections in Activesync menu (right click on green icon on the tray)-->connection settings-->untick "Allow USB connections"
2.Put your device in bootloader mode (yours is in it)
3.Start to connect it with MTTY to do what you want or just run an official Orange UK ROM update
If everything is fine,your device will be alive again.
After that install Hard-SPL to avoid problems like this.
BR
Scootie
P.S.:Sorry,I didn't read post #3,but it can be useful later.
One more tip:check the camera button.
Thanks Scootie,
I'll try the Hard-SPL thing - the jumping into boot loader seems pretty random, has happened a couple more times and I find I have to pull the battery for several minutes and then try a restart.
The camera button doesn't seem to do much other than what it is supposed to.
Pretty annoying since I have had the phone for 3 years, but have not had signal at home so hardly use it, and now we have signal due to Orange/T-Mobile merger from the beginning of the month the phone fails me :-(